Search Documents

By A. G. Journel

The regionalization of tungsten grades at the deposit represents an ideal case for anisotropic hole-effect variogram modelling. The modelling technique is presented step-by-step and the consequences of the model on block kriging are indicated.

Jan 1, 1982

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By R. E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on giving mine operators the capability to evaluate the higher production, the lower costs, and safety enhancement that comes with mechanical mining. The opportunities for low cost and high production must outset the high capital costs associated with mechanical excavation. Giving the mining industry the tools to effectively evaluate and successfully implement mechanical methods defines the challenges and directions of the mechanical mining industry.

Jan 1, 1994

By H. E. Wyslouzil

The highly competitive nature of the international iron ore market has forced producers to improve the quality of their pellets. The demand for low acid pellets suitable for direct reduction has resulted in an increase in the number of plants utilizing reverse froth flotation for silica reduction. Column flotation is being favoured for this service due to the low capital and operating cost of the equipment, as well as improved metallurgical performance when compared to conventional flotation cells. This paper describes the benefits of column flotation and discusses some important aspects of circuit design.

Jan 1, 1993

By R. M. G. Machunter

The presence of ultra-fine particles affects the separation performance of wet gravity separation equipment. Several studies have been undertaken to establish the maximum level of these particulates that can be tolerated by spiral separators and it has been found that unless the ultra-fine material is effectively processed, relatively low proportions in the ROM material combined with high feed rates can result in degradation in plant performance and/or excessive water consumption. The maximum level of particulate material in the process water has been determined by examination of separation performance of spiral separators under varying slime loading. This work has been conducted utilizing various feed sources and a robust ‘rule-of-thumb’ has been derived.

Jan 1, 2005

By E. Taskin

Diasporic bauxite from the Mugla-Milas region was mechanically activated in a planetary mill for different activation times and the structural changes were examined by X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and specific surface area analysis (BET ? Burnauer, Emmett and Teller). Non-activated and activated bauxite samples were leached directly in alkaline (Na2O) solution at atmospheric conditions and the activation procedure led to the amorphization and structural disordering of the diasporic bauxite structure, which increased the dissolution efficiency. Effects of milling speed, liquid/bauxite ratio and leaching time on alumina extraction in direct alkaline leaching of diasporic bauxite were also studied. The alumina extraction was ~7% for non-activated bauxite and ~70% for activated (75 minute) bauxite. Key words: Diasporic bauxite, Mechanical activation, Alkaline leaching, Alumina extraction

Jan 1, 2009

By E. Bakhtavar

In this paper, problem of short-term production planning for dimension stone quarries was mathematically modeled using a binary integer programming. The model includes an objective function, which was founded as the minimization of the costs due to the total cutting planes of the blocks. This objective may cause to maximization of the net present value (NPV) in dimension stone quarries. During the mathematical modeling the essential constraints are dimension stone quarry capacities and the market demand, block accessibility for the equipment and the reserve constraints. As a base, an optimal size and shape of extractable blocks should be first assigned according to the available extraction technique and the market demand, in order to create a geological block model. Then an economical block model is provided by assignment of a value of ?one? for ore blocks and ?zero? for waste. Maximum profitability and minimum amount of the ore wastage can be gained using this plan and modeling.

Jan 1, 2012

By W. Ellison

Worldwide development of commercial markets for FGD (flue gas desulfurization) gypsum is described and used as a basis for assessing potential overall market growth and regional demand foreseen in the U.S. during the 1990s. Diverse strategies are outlined for cost-effective substitution of this major supply from acid rain control retrofits (power plant scrubbers) for natural gypsum in the principal, existing markets: gypsum board and portland cement. Another focus of utilization forecasting is a key group of related. new-product advancements including floor screeds, mining mortars and various types of innovative construction products.

Jan 1, 1993

By Guangyao Si, Ismet Canbulat, Xun Luo, Yi Duan

Routine analyses of seismicity and event locations are essential for coal burst risk management, especially in the presence of unfavorable and complex geology. In an Australian longwall coal mine, a small-scale seismic monitoring network was installed to monitor a section of a major dyke intersected by the roadway, which was classified as a coal burst prone zone. The Deep Convolutional Neural Network (DCNN) technique was adopted for automatically discriminating seismic events to assess seismicity in this zone. The discriminated seismic events were located with the Shortest Path Method based on the Boundary Discretization Scheme (BDS-SPM) for temporal-spatial seismic event distribution analysis. The results demonstrate that the seismic events are discriminated with an average accuracy of 94%. Moreover, the seismic events are more accurately located using the BDS-SPM with a 3D heterogeneous velocity model compared with results obtained with a homogeneous velocity model. The temporal and spatial variances in seismic activities identify that the rock fractures in the dyke zone are closely related to the longwall mining process and a local dyke has a controlling influence on the stress concentration in its vicinity.

Apr 26, 2022

By F. Ansheng

Though it becomes increasingly important with the valuable minerals in their deposits tending to be fine and poor, the solid and liquid separation remains difficult especially when the particles are of micrometer size and of low density. Almost of all conventional thickeners result in that fine particles lose into overflows which often costitutes a loss of potentially valuable resources as well as an environmental hazard. The addition of flocculations may improve the settling of solids but may also not work well for the final removal of fine particles from the overflows (Ref.1).

Jan 1, 1990

By Christopher Mark

Area wide pillar failures, or “squeezes,” were once fairly common in underground coal mines. While rare today, they do occur. This paper describes seven case histories that were investigated by MSHA Technical Support. They occurred across the range of US coalfields, in both longwall and room-and-pillar mines, and involved development mining, pillar recovery, longwall panel extraction, and multiple seam interactions. Significant lessons from each are discussed.

Jun 25, 2024

By L. Schlink

Impacted waters, often complex, are created in mining which at some point in the mine life cycle will need to be attended. The simplest and most cost effective method of handling impacted water is to reuse it as makeup water for operations. At the end of mine life, operational reuse will not be an option and the impacted water will require treatment to achieve alternative reuse goals. Conventional mine impacted water treatment is successful in removing unwanted constituents but create brine and sludge that may require special handling or additional treatment, resulting in additional liabilities and costs. Freeport-McMoRan Copper & Gold has taken an approach to water treatment that focuses on transformation not concentration. The Water Treatment Test Facility located at Sierrita Mine has three test plants that are piloting the mine impacted water transformation process. Two plants have been designed for the removal of calcium and sulfate with products of gypsum and sulfur. The third plant removes metals from process water and transforms them into marketable metal sulfides. The transformation, rather than concentration, of mine impacted water solutes greatly reduce long term risks.

Feb 23, 2014

By A. J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of steel wire ropes. Steel wire ropes are very suitable for mine hoisting due to their high strength and durability, but have the negative characteristic of a low strength/weight ratio. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength/weight ratio of synthetic ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application.

Feb 23, 2014

By R. L. Grayson

A goal programming-based worker scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model the accomplishment of each regular and non-regular job is a goal. The objective is minimization of the deviations away from the goals. A number of coefficients are used as premultipliers of the decision variables in order to address practical considerations associated with the utilization of workers and the requirements of jobs. Some of these premultipliers will be updated expertly within MMSS, timely updating the statuses of the dynamic parameters.

Jan 1, 1991

By P. Somasundaran, S. Venkatachalam, N. K. Khosla, K. Khosla

Froth flotation of alumina particles was studied by employing and hydrogen gas bubbles. The effect of current density was studied over a range of 0.1 to1.6 kA/m2. Compared to hydrogen, the use of oxygen bubbles at any given gas evolution rate resulted in a higher flotation recovery. The existence of an optimum current density, for each given particle size was indicated. Flotation at higher current densities resulted in better flotation kinetics, while flotation at lower current densities resulted in better Spas utilization.

Jan 1, 1996

By Francois E. Heuze

This paper summarizes the geomechanics programs conducted in two hard rock underground mining operations in the Western United States, between 1966 and 1981. The two projects were directed towards understanding the behavior of the rock masses, at the scale of the caverns. To this end, the emphasis was put on large scale field measurements, complemented by limited laboratory testing. The results of these observations were used to build realistic finite element models of the underground chambers. In the marble mine, at Crestmore, California, the models were applied to the structural optimization of the room-and-pillar pattern. In the granite mining, at Climax, Nevada Test Site, the models explained some unusual stress changes observed during excavation. Based on the large number of geomechanical techniques employed, specific conclusions and recommendations are offered regarding the quality, applicability, and usefulness of the various methods. The two case histories clearly indicate chat numerical models are extremely useful for a detailed understanding of the structural behavior of mine openings. To be realistic, these models must be based first and foremost on large scale field observations. The lessons Learned on these two projects also are directly applicable to the design and analysis of nuclear waste repositories in hard rocks such as basalt, granite, and welded tuff.

Jan 1, 1982

By G. M. Wilemon

The U.S. Bureau of Mines has conducted preliminary investigations on the leaching of phosphate ores obtained from deposits in the western United States using sulfuric acid (H2SO4) in the presence of methanol. Phosphate extractions in excess of 80 pct were obtained on an ore sample from Pocatello, ID. Initial leaching studies using the ore as received yielded extraction levels of approximately 35 pct. However, when the sample was ground for as little as 5 min in a rod mill, in methanol, then treated with HzS04, 82 pct extraction was achieved. The R2O3-P2O5 (R2O3 = Al2O3 + Fe2O3) ratio of the starting material was 0.11. Solubilized products after leaching exhibited an R2O3-P2O5 ratio of 0.02, which is well within desired limits. These results illustrate the potential of acid-alcohol leaching for recovering phosphate values from marginal-grade ores and as an alternative to methods involving current beneficiation techniques that yield lower phosphate recoveries.

Jan 1, 1992

By D. Einarson, B. Strickland

The decision to accelerate development of Stillwater Mining’s East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and RailSystems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km(3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By G. A. Shirey

Breakthroughs in software technology and in computer hardware capabilities have opened new opportunities to develop more accurate process simulators and to reduce the operating time to reasonable levels. As a result, there are several new simulation packages being commercialized for modeling coal preparation plants and pulverized coal-fired power plants, and the users of these packages are reporting significant improvements in process efficiency and operating costs by implementing the simulators' results. This paper provides an overview of some of the models currently in use at CQ Inc., including the ASPEN PLUS"" Coal Cleaning Simulator, the Ultramax® process optimization software package, and EPRI's Coal Quality Impact Model?. Case histories of specific applications are also presented.

Jan 1, 1995