Search Documents

By William C. McBee

Prompted by forecasts of a sulfur oversupply, the Bureau of Mines, U.S. Department of the Interior, is conducting research on potentially large-scale uses of this commodity to extend or replace such construction materials as asphalt, cement, and mineral aggregates. Through these efforts, paving materials have been developed in which sulfur replaces up to 50 pct of the asphalt normally present and which can be prepared and placed with existing mixing and paving equipment. Laboratory properties and design methods for this direct mixing process are described along with properties obtained on small-and large-scale field demonstration projects. These properties are compared with those obtained from control materials prepared without sulfur additions. Monitoring for toxic gases during laboratory and commercial mixing and paving operations is discussed also.

Jan 1, 1978

By B. H. Eccleston

The Bureau of Mines, in cooperation with the American Petroleum Institute, studied the effect of fuel volatility and front-end fuel composition on the amount and photochemical reactivity of automobile exhaust and fuel-system evaporative emissions. The study involved six gasolines--the base fuel, three fuels of varied volatility, and two fuels differing from the base and from each other in front-end olefin content. Data were obtained from 16 vehicles operated on a chassis dynamometer using a speed-load-time cycle that approximated a typical urban trip. Tests were made at ambient temperatures of 20°; 45°, 70°, and 95° F, using a climate-controlled dynamometer room. The amount of hydrocarbon emission and its probable photochemical effect, a potential contribution to pollution, is expressed as weight (reactivity equivalent) of a moderately reactive material, ethylene. Emissions of oxides of nitrogen, car-bon monoxide, and aldehydes were also observed. Results showed that reduction of volatility from currently typical levels serves to reduce both the amount and the reactivity equivalent of evaporative losses with a slight penalty by way of higher exhaust emissions. Alternatively, reducing the amount of light (low boiling) olefin in the fuel had no effect on the amount of hydrocarbon pollutant but did significantly reduce the reactivity equivalent of the emissions. Neither volatility change nor chemical changes to the fuel significantly affected the nonhydrocarbon emissions.

Jan 1, 1970

By W. W. Graff

This paper describing the mining practice at Mine No. 5 of the Marquette range, Michigan, is one of a series being prepared by the Bureau of Mines on mining practices, methods, tend costs in the various mining districts of the United States. The top-slicing system of mining, has been used ever since the present operating company took control of the property in 1903, the main level and sublevel layout being chanced only as local conditions required and the use of mechanical equipment increased.

Jan 1, 1930

By W. A. Haley

The purpose of this investigation was to develop and improve mining methods for mining thin coal beds, to increase productivity, and to increase the recovery of coal. German coal planers and a modified longwall system of mining were introduced into American mines and are bringing about increased productivity and better recovery as compared with the conventional methods displaced. Since the first installation, 4 additional planers have been purchased by coal companies and over 1-1/2 mil¬lion tons of coal has been mined by them, using the modified longwall mining method. INTRODUCTION Except from 1932 to 1934, the growth of mechanical loading in underground bituminous-coal and lignite mines in the United States has increased steadily. The amount of coal loaded mechanically in underground mines has increased from 0.3 percent in 1923 to 79.6 percent of the total underground production in 1953.3/ The use of new and improved mining machines and auxiliary equipment, together with new techniques in mining methods, usually has resulted in increased productivity.

Jan 1, 1957

By Jerry W. Stengel

The Bureau of Mines subjected two manufacturers' chemical oxygen (K02) self-rescue breathing apparatus to a series of laboratory environmental treatments designed to simulate various conditions in underground coal mines. The environmental treatments consisted of extremes of temperature, shock, and vibration. The tests were designed to be used as predictors of the ability of the self-rescuers to survive those environmental insults with no degradation in their protection to the wearer. Based on the severity of the treatments, simulating conditions more severe than offered by the mining environment, the two apparatus tested should be able to withstand the abuse offered by the mining environment and still function as intended in an emergency. Correlation of these tests with results of long-term field evaluations is needed to provide confidence in the laboratory tests as predictors.

Jan 1, 1982

By G. S. Rice

The recommendations of the Bureau of Mines on rock-dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions,5 approved by the. American Engineering Standards Committee,6 December 30, 1925 It is specified that the dust to be used is of a size that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch.

Jan 1, 1930

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the noncondensable cases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of uses produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills.

Jan 1, 1931

By J. D. Hadden

The Bureau of Mines conducted drilling studies in the Pocahontas No. 3, the Pittsburgh, and a western coalbed to establish the gas migration characteristics for each. Gas pressures in the Pittsburgh coalbed were about 260 lb/in2 and in excess of 550 lb/in2 in the Pocahontas No. 3. Caving in drill holes prevented pressure measurements in the western coalbed. The Pittsburgh coalbed contained intersecting "clay veins" which formed gas pressure cells. Although these geological features hamper mining, they can be used to control the flow of methane into a mine working. Methane control techniques are proposed for the Pittsburgh and Pocahontas No. 3 coalbeds.

Jan 1, 1969

By S. M. Runke

An ever-increasing demand for beryllium and beryllium alloys has directed attention to the milling of low-grade domestic deposits as a possible means of supplying part of the Nation's ore requirements. The United States generally produces less than 10 percent of its annual supply. For example, new supply in 1953 was estimated at about 9,250 tons, of which the United States imported 8,500 tons. Domestic production was only 750 tons.2/ Since record high prices for beryl in 1952 and 1953 did not greatly increase domestic product ion, the United States must develop mechanical beneficiation processes to use low-grade deposits and reduce dependence on foreign sources

Jan 1, 1954

By C. M. McCulloch

As part of the Bureau of Mines methane control program, the Pittsburgh coalbed was studied in Washington and Green Counties, Pa., and in Marion and Monongalia Counties, W. Va., where this coalbed is now being mined at its greatest depth. The coalbed thickness appeared to be structurally controlled; the bed was generally thinner near the axes of anticlines and thicker near the axes of synclines. The overburden isopach shows a similar relationship. Most of the clay veins in coal occur in the synclinal troughs, generally under sandstone roof. Cleat orientations measured in 18 underground mines showed that face cleats are perpendicular to the axial trends of the folds, and the butt cleats are parallel to the axial trends, indicating structural control of the cleat. Measurement and analysis of surface joint orientations provide a method for predicting the cleat orientations of the coalbed, but linears measured from infrared photographs and photoindex sheets helped only to determine regional trends. The results of these investigations provide a geologic framework for rational planning for underground mine development to use the best available technology to cope with methane emissions, coalbed discontinuities, and related ground support problems.

Jan 1, 1975

By L. C. IlsLey

From time to time the Bureau of Mines has issued publications dealing with the various classes of explosion-proof mining machinery that have been tested and approved as permissible for use in mines having atmospheres that may become inflammable by reason of the inadvertent presence of gas or dust. These publications are confined almost entirely to description of the features contributing directly or indirectly to the prevention of explosion or shock hazards, and are intended to give inspectors, safety engineers, and others already familiar with the general safety requirements more detailed information on the safety features of the design of a particular machine. As a background for papers describing permissible machines and to avoid the necessity of duplicating descriptions of methods of conducting investigations and tests of such machinery, Bureau of Mines Bulletin 305, Inspection and Testing of Mine-Type Electrical Equipment for Permissibility, was published in 1929. Three bulletins giving detailed descriptions of the three most numerous types of machines have been issued, viz., Bulletin 313, Permissible Storage-Battery Locomotive and power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment.

Jan 1, 1937

By G. S. Rice

The recommendations of the Bureau of Mines on rock dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions, approved by the American Engineering Standards Committee. December 30, 1925. It is specified that the dust to be used is of a elm that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch. Thus the coarsest size of dust and the minimum proportion of fine dust are specified, but the specification does not indicate whether a larger proportion of fine dust would be desirable. There have been advocates of the use of that size of rock dust of which the particles would all approach 200-mesh in fineness. Explosion tests were made in the Experimental mine in the earlier period of testing which indicated that the finer rock dust is somewhat more effective under test conditions, but not sufficiently so to Justify the cost of finer grinding of the dust; also there are some disadvantages of finer dust described hereafter.

Jan 1, 1930

By John D. Corrick

Three species of chemosynthetic iron- and sulfur-oxidizing autotrophic bacteria have been isolated from the leaching waters of copper mining areas. These species are: The sulfur-oxidizing Thiobacillus concretivorus, the iron-oxidizing Ferrobacillus ferrooxidans, and a sulfur- and iron-oxidizing bacterium closely resembling Thiobacillus ferrooxidans, INTRODUCTION Among several suggested new processes for treating marginal ores in the United States, none is more intriguing than the possibility of extracting metals from low-grade materials by the action of microorganisms One phase of a Federal Bureau of Mines investigation toward developing such a procedure was to isolate and identify specific chemosynthetic iron and sulfur. oxidizing autotrophic bacteria native to certain domestic copper deposits where leaching is practiced. The bacteria or microorganisms considered important to this investigation are those capable of producing solutions of ferric sulfate and sulfuric acid. Solutions of this type are excellent solvents for some copper minerals By establishing the presence of these bacteria at certain copper-leaching areas, strength would be given to a theory that microbial activity is partly responsible for the oxidation that takes place at these areas. Their presence also advances possibilities for controlled use of microbial action in metal extraction processes. Leathen4/ has demonstrated that one of the chemosynthetic iron-oxidizing bacteria, Ferrobacillus ferrooxidans, can oxidize 200 parts per million of ferrous iron to the ferric state in 3 days,

Jan 1, 1961

By T. E. Purcell

(a) Moisture. - Moisture, "as fired," is specifically significant in pulverized-coal firing because of its effect upon the continuity of raw-coal feed to the pulverizer, pulverizer capacity, flame stability, and speed of ignition. The extraneous moisture content is a rough index of potential difficulties in unloading and maintaining the flow of raw coal to the pulverizer and of pulverized coal to the furnace, with the troubles increasing geometrically as the percentage increases. Sticking or other stoppage of coal flow at any point between the bunker and the furnace is especially serious with pulverized-coal firing because there is danger of immediate loss of output. Where moisture is a problem, the designer must exercise great care in the design of coal-handling and preparation apparatus.

Jan 1, 1951

By J. Bender

The objective of this research was to (1) Further develop cyanobacteria mats' for metal-tolerance and cold-tolerance, (2) test them for durability in the field environment and (3) assess them for metal sequestering potential with actual and simulated field samples. Results show that mats performed well In the field and effectively sequestered metals from actual and simulated field samples. Metal uptake from Iron Mountain Hine samples was for Ins 87%, Cu and Cd 99%, Initial concentrations (mg/L) were Zn = 3,250, Cu , 279, Cd = 28. In solutions simulating the Gulf Tunnel drainage, Zn and Mn were effectively removed by mats immobilized on glass wool. Effluent water, after treatment, generally had a Ph of 7 .5-8.5. Al though the final metal concentrations in the mats 'harvested from the decontaminated water were only 1% or less, the actual mechanism of metal deposit was probably a mat-mediated alteration of the environmental conditions causing the metals to deposit outside the mat as oxides or carbonates. Bioflocculents, released by the mats, were likely involved in the metal-removal process.

Jan 1, 1996

By W. P. Diamond, John C. LaScola, D. M. Hyman

In 1972, the Bureau of Mines developed a direct-method test for measuring the gas content of virgin coal core samples for coal mine health and safety considerations. Since that time, approximately 1,500 coal samples from more than 250 coalbeds in 17 States have been collected for gas content determination. The gas content data, when combined with geologic and engineering studies, can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if methane drainage in advance of mining should be considered. The data are also critical in delineating coalbed methane resources and in utilization feasibility studies. This report makes the Bureau's extensive data base of gas content data more readily available to the coal and gas industries. The data are presented in tabular form, alphabetically by coalbed name and by State. The components of the total gas content (lost, desorbed, and residual gas) are given, Location (State and county), sample depth, coalbed or formation name, and coal rank are included for geographic and geologic identification.

Jan 1, 1986

By Charles F. Weber

Premature blasts of charges of explosives have caused many deaths in anthracite mines, and the causes of many of the blasts were not determined satisfactorily. Investigators often found fairly high potential differences between such metallic objects as rails, pipes, conveyor lines, or sheet-iron chutes in the working place where an accident had occurred. At one mine where a premature blast occurred in a rock tunnel, one workman was killed and two others were injured, and several days later a potential difference large enough to explode an electric squib was detected between the compressed-air pipe and the track rail; the voltage fluctuated and appeared to change with the movement of a locomotive. At another mine, a. workman was killed when a primed cartridge that he was about to load in a blast hole exploded in his hand. During the investigation, a potential difference was found between the conveyor line and the sheet-iron chute. During a 5-year Period, 61 fatalities and 771 nonfatal injuries were caused by explosives accidents in anthracite mines, and one of the chief causes of these accidents was premature blasts.

Jan 1, 1950

By C. M. K. Boldt

This report summarizes five separate Bureau of Mines contract studies on the use of aerial photogrammetry, satellite transmission of in situ instrumentation information, and satellite imagery to monitor and update mine waste embankment data. The equipment used, methods applied, results, recommendations, and cost analyses are presented along with a bibliography of related investigations.

Jan 1, 1987

By G. E. McElroy

Economic solutions of problems of mine-ventilation improvement can be found by mathematical analyses of alternative methods of procedure, but, in the case of our older bituminous-coal mines, the airway network is usually so complex that mathematical solutions are too tedious to be practical. Recourse usually is made to extremely costly and uncertain trial-and-error procedures with the existing layout and equipment. The resulting errors often prove costly and sometimes create hazardous conditions. Both the economic and safely aspects of alternative methods of ventilation improvement may be rapidly and cheaply investigation with analogue computers. An electrical analogue computer, designed and built especially for analyzing mine-ventilation-distribution problems, has been placed in service by the Bureau of Mines at its Pittsburgh, Pa., Experiment Station. It is a nonlinear, low-voltage, fluid network analyzer of a type developed by Malcolm S. Mcllroy, professor of electrical engineering at Cornell University. It was designed in close coopera¬tion with Professor Mcllroy and built by the Standard Electric Time Co., Springfield, Mass. It is the seventh unit of this type to be placed in service and the first designed for mine airflow problems. The other six were designed for either water- or gas-distribution analyses. Three are much larger and more expensive units. The largest unit has a capacity of 20 sources, 576 mains, and 180 loads, or regulated-flow paths. The Bureau unit has a capacity of 5 sources, 128 mains, and 48 loads.

Jan 1, 1954

By H. W. Davis, Richard J. Lund

"In presenting the results of this survey on consumption of ferrous scrap and pig iron for the year 1935 the Bureau of Mines, responding to requests from industry, seeks to fill a major gap that has long existed in the field of metalliferous raw-material statistics. This type of information is designed to meet the needs of: (1) Consumers of ferrous scrap. including operators of blast furnaces, steel mills, ferrous foundries, and rolling mills; (2) marketers of scrap iron and steel, including large brokers who sell, and dealers who collect, prepare, and sell the material; (3) large scrap producers; (4) producers of iron ore, with which scrap competes indirectly; and (5) other individuals and agencies interested in more general economic analysis, since the scrap market has repeatedly been cited as one of the most sensitive of all industrial barometers, If the survey prover as useful as now seems probable, it will be continued annually with possibly an enlarged scope of treatment.The Bureau appreciates that its first efforts in this field may not meet all expectations: but it hopes to develop gradually, through suggestions, advice, and criticism from the industrial groups most interested, a type of analysis that will accord closely with technical processes and best meet the needs of all groups vitally interested in supplies and use of ferrous scrap. Constructive criticism and suggestions from industry regarding improvements to be desired in the conduct of future surveys on this subject will therefore be warmly received by the Bureau."

Nov 1, 1936