Search Documents

By C Ferron, R Massimi

There is approximately 240 000 tonnes of arsenic trioxide dust stored in underground chambers at the Giant Mine in Yellowknife, Northwest Territories, Canada. To minimise the amount of arsenic released to the environment, a number of closure alternatives are being considered. One alternative is to mine the dust, encapsulate it and dispose the mixture into a secured landfill. The potential leaching behaviour of the encapsulated dust was examined in a laboratory programme. Cylinders of arsenic trioxide dust mixed with cement/aggregate and bitumen were prepared. The dust content varied between zero per cent and 60 per cent of dry weight charge. The cement cylinders were tested for strength, leaching and freeze/thaw durability. The bitumen cylinders were tested for leaching only. The results show that increasing dust content in the cement cylinders negatively impacts the strength and the freeze/thaw durability of the samples. A contributing factor is likely the high water to cement ratio in the samples. Leaching tests show that arsenic release from cement cylinders increase with increasing dust content. Arsenic concentrations in leachates do reach a plateau at a certain point in time. Arsenic release from bitumen cylinders was significantly lower compared to cement cylinders. Arsenic concentrations eventually were less than 0.05 mg/L in samples containing up to 25 per cent arsenic trioxide dust. Arsenic leaching rates were found to decrease by an order of magnitude over the course of three months.

Jan 1, 2003

By P. S. Haury, Thomas C. Denton

"INTRODUCTION AND RESUMEThe Reward zinc property was one of the first selected for exploration by the Bureau of Mines at time when zinc supplies for war production were very short. Preliminary examination indicated that an appreciable tonnage of zinc that could be developed for early production might be found by diamond drilling. The geology was mapped by the Federal Geological Survey, and 14 holes were diamond drilled by the Bureau of Mines. This work was started in September 1942 and completed in September 1943.The Reward is an old property in southwestern Pinal County, 26 miles from Casa Grande on the Southern Pacific Railroad. Mining was begun in the early 1880's and was continued intermittently by several operators to about 1917. About 400,0oo pounds of copper was produced from the north¬eastern part of the property, mainly from a 600-foot incline in oxidized copper ore that replaced a bed of limestone. This ore was mined out. A 400-foot vertical shaft in the copper area was inaccessible. A 325-foot vertical shaft had been sunk near the southwest end of the zinc-bearing area, and a 600-foot crosscut tunnel had been driven near the northeast end of the zinc area, but little zinc ore was produced. There were several shallow inclines and numerous surface pits between the main workings.The ores were deposited in Paleozaic limestones that strike northeast and dip about 40 degrees northwest. These are capped by Cretaceous clastic and volcanic rocks in the zinc area. The outcrops show mineralization in a segment of the limestone 4,500 feet long, which is limited by large cross faults at each end. Another large fault, which strikes north, separates the northeast third of the mineralized belt from the remainder. Copper predominates northeast of this fault and zinc southwest of it. The ore beds are cut by numerous small cross faults. Ore was deposited for short distances along some of these, but more of it made out from the fissures along certain replaceable limestone beds."

Nov 1, 1946

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By Walter K. Utt

The vibration levels of the heavy machines used in surface mining are much greater than for vehicles used on highways. In order to assure the proper functioning of electronic equipment placed on the surface mining vehicles, the U.S. Bureau of Mines has conducted a program of field measurements to define their vibration environment. The information in this report is for a class of vehicle that has a blade for scraping and wheels with rubber tires. The statistical information derived from these measurements can be used as a basis for laboratory testing to qualify equipment for a surface mining vehicle of this class. The envelope that would encompass 99 pct of the vibrations encountered in normal operations is presented for each location on the vehicle. The five locations for which data were recorded are the floor of the cab, the engine, the frame, the drive train (gear, differential, and torque converter), and the axle. Tabulated data are provided for those who wish to use a different probability level. The appropriate test profile for the laboratory testing can be determined from the information presented in this report.

Jan 1, 1993

By J. B. Lott

The authors' company has recently undertaken a development programme aimed at exploring the relationships between the variables of greatest importance in the design of mixer-settlers for metallurgical solvent extraction applications. Such applications vary from relatively small scale plants treating copper mine waters, nickel containing effluents, etc., where the total flowrates may be of the order of a few hundreds of gallons per minute, to very large scale plants treating several thousands of gallons per minute of leach liquors containing copper, uranium or other metals. This paper outlines the physical and mechanical factors which must be taken into account when designing mixer-settler systems for large scam. solvent extraction plants. The performance of the equipment will also be dependent upon the chemistry of the system, including the kinetics and thermodynamics of the ion exchange reaction itself, the effect of impurities flocculants, surfactants, temperature, etc., but these will not be dealt with here. Much of the laboratory work has been carried out using copper containing solutions and either LIX 64* or LIX 64N* as the solvent dissolved in various grades of kerosene. For simplicity, all the graphs and tables of results which are presented and discussed here will refer to the LIX-copper system, although the conclusions will in many cases be generally applicable to other systems also. The LIX-copper process is now sufficiently well known to obviate the need for a full description, however, an outline flowsheet of the process is shown in Figure 1. The ultimate objective of a laboratory programme for a particular extraction application is to provide data upon which a mixer-settler system can be designed to handle a given throughput of leach liquor and extract from this liquor the maximum quantity of metal for the minimum cost. In other words, the objective is to determine the design and operating parameters which achieve the optimum balance between capital and operating costs. * Trade-marks for General Mills solvents.

Jan 1, 1971

By A. L. Mular

Some specific cases of the collection of data from industrial grinding and classifying operations, and the development of models from the data so obtained, will be described. The problems encountered, the effort involved, and the value of the derived models in improving the plant efficiencies will be discussed and documented where possible.

Jan 1, 1971

By W. M. Cross

Optical fibers have revolutionized the telecommunication industry, because of their ability to transmit large amounts of data over long distances. Without optical fibers many of the communication technologies on which business, industry and research rely would be impossible. In addition to their use as communication devices, optical fibers are often used as sensors. Despite the great promise that optical fibers have for the development of many types of remote sensing devices, few remote sensing devices have been built for use in the mineral industries. This paper will describe the use of optical fibers as sensors for surfactant adsorption at mineral surfaces.

Jan 1, 1995

By Atmesh K. Sinha

Death and injury rates in mining have been the highest of any industry; the injury severity rates in mines have also been the highest. Tentative figures reveal that 1971 was the best year yet for the bituminous coal indus¬try with the lowest number of fatal accidents. Nevertheless, 177 men were killed at a frequency rate of 0.76 per million man hours. Coal mine accident statistics have been described at various times as unacceptable and intolerable and recently resulted in the enactment of massive legislation. The 1969 Coal Mine Health and Safety Act was passed by Congress "to improve the working conditions and practices in coal mines and to prevent accidents and occupational diseases originating in the coal mining industry." The prevention of accidents in coal mines is the statutory responsibility of mining engineers and the moral responsibility of all who have any part to play in mining coal. The questions to be answered by these men may well be - What are the reasons for the high accident rate? Are the mines as safe as they can be? Are our mines sufficiently manned to insure proper supervision of production cycles and safety requirements? Are our plans for safety committees, safety campaigns, and safety inspections sufficient? Are they producing the results intended? If not, how can these be reorganized to have a greater impact? What is the real cost of an accident? What are the immediate and long-term plans for further improvements? These questions are in no way exhaustive, and the answers are not easy. There are many aspects of mine safety, and any one of them can be the subject of a lengthy discussion. The aim of this paper, therefore, is to limit the analysis to documented fatal electrical accidents in mines so that meaningful conclusions for improvement in electrical accident-experience statistics can be made. In doing this, it is also the intention to emphasize areas of missing information and propose a few suggestions for better hazard analysis.

Jan 1, 1972

By P. Syrjänen, Lovén. P.

Because geostatistics together with block modeling has not been studied in detail before in the rock mechanics, a two-year research program to investigate the practical use of geotechnical modeling was started in Finland in 1999. According to research work results block modeling gives good estimate of overall rock mass quality but it can not identify individual structures like faults and narrow weakness zones. Weakness zones and faults should be mapped from drill cores, surface mapping, geophysical methods etc. and manually generate 3-D structural model. Rock mechanical 3-D modeling can be used for preliminary stope dimensioning and preliminary reinforcement design. Detailed design needs rock quality mapping from drifts during excavation work. La géostatistique associée à la modélisation par blocs n'ayant pas été étudiée en détail jusqu'à présent dans la mécanique des roches, un programme de recherche sur deux ans visant à examiner l'utilisation pratique de la modélisation géotechnique a été lancé en Finlande en 1999. D'après les résultats des travaux de recherche, la modélisation par blocs donne une bonne estimation de la qualité générale de la masse rocheuse mais elle ne permet pas d'identifier les structures individuelles comme les failles et les zones géologiquement dégradées étroites. Ces zones et failles devraient être cartographiées à partir de carottes de sondages, d'une cartographie de surface, de méthodes géophysiques, etc. et générer manuellement un modèle de structure 3D. La modélisation mécanique des roches en 3D peut être utilisée pour un dimensionnement de la chambre et un plan d'armature préliminaires. Un plan détaillé nécessite l'élaboration d'une cartographie de la qualité des roches des galeries lors des travaux d'excavation. Da man früher Geostatik und Block-Modellieren in der Gebirgsmechanik nicht detailliert untersuchte, wurde 1999 in Finnland ein zweijähriges Untersuchungsprogramm in Angriff genommen. Aufgrund der Untersuchungsergebnisse ergibt das Block-Modellieren eine gute Beurteilung der gesamten Gebirgsmassenqualität, kann jedoch einzelne Strukturen wie Verwerfungen und kleine Schwachzonen nicht identifizieren. Schwachzonen und Verwerfungen müssen demnach aus Bohrkernen, oder mit Hilfe von Oberflächenkartierung, geophysischen Verfahren usw. ermittelt und danach ein 3-D-Strukturmodell manuell erstellt werden. Felsmechanisches 3-D-Modellieren ist für die vorbereitende Abbaudimensionierung und für die vorbereitende Bewehrungsplanung verwendbar. Ein detaillierter Entwurf benötigt die Kartierung der Gesteinsqualität aus den Gesteinsstrecken während der Ausbrucharbeiten.

Jan 1, 2003

By K. Holmberg, D. Herriot

This paper by Mr Mclvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulat¬ing load operation. The Bond calculation is itself based upon

Jan 1, 1989

By Fanor Quinteros

El presente trabajo señala el sistema administrativo de trabajo de 2 X 1 en la mina Raura aplicado desde setiembre del 2000, cuyos resultados obtenidos satisfacen las metas trazadas y justifican el costo de inversión que pudo generar su implementación. Asimismo se muestran las ventajas para el trabajador y la comunidad, el marco jurídico, el procedimiento empleado para la instauración al sistema y su evaluación.

Sep 13, 2001

By E. Shelobolina, S. M. Pickering, J. E. Kogel

A long history of weathering and bacterial alteration processes have transformed Georgia’s Coastal Plain kaolins from dark organic muds to recrystallized white pigment-grade industrial clays. A sequence of six stages in development of these valuable mineral deposits is outlined over their Late Cretaceous and Tertiary deposition and alteration history. Anaerobic and aerobic iron oxidizing and iron-reducing bacteria are present in the Georgia kaolins. These bacteria may have had a major role in iron and organic matter removal during several of the alteration stages that occurred over the past 60+ million years. Iron was likely solubilized by both iron-reducing and iron-oxidizing bacteria, depending on availability of Fe(II), Fe(III), and NO3. Thus, over long periods bacterial activity slowly led to nearly complete groundwater removal of iron from the kaolin deposits. Further bacterial iron removal on an industrial process scale may eventually prove feasible. “Without the multitude of living reactions as channels for energy and electrons and without the enormous capability of life to transfer with and against chemical gradients, there would be practically no or at least a very reduced geochemical rock cycle on this planet.” (Krumbein and Dyer, 1985, p. 157)

Jan 1, 2002

The concept of isokinetic measurement of strength was originally related by Hislop and Perrine.(1)Characteristics of an isokinetic exertion are constant velocity throughout a predetermined range of motion. Strictly speaking, a means of speed control, and not a load in the usual sense, is applied in isokinetic exertions.(1)However, load and resistance are definitely present in this technique. In this case, the load is a result of the energy absorption process performed by the device to keep the exertion speed constant. The device prevents energy from being dissipated through acceleration in isokinetic exercise. The energy is instead converted into a resistive force, which varies in relation to the efficiency of the skeletal muscle. Since the speed of motion is held constant in isokinetic exercise, the resistance experienced during a contraction is equivalent to the force applied throughout the range of motion. For this reason, the technique of isokinetic exercise has sometimes been referred to as accommodating resistance exercise. This type of exercise allows the muscle to contract at its maximum capability a tall points throughout the range of motion. At the extremes of the range of motion of a joint, the muscle has the least mechanical advantage, and the resistance offered by the machine is correspondingly lower. Similarly, as the muscle reaches its optimal mechanical advantage, the resistance of the machine increases proportionally. It must be understood, however, that while isokinetic devices control the speed of the exertion, this does not assure a constant speed of muscle contraction. The speed of isokinetic contractions is constant during individual exertions; however, it is also possible to compare muscular performance over a wide range of isokinetic velocities. Increasing the isokinetic speed of contraction will place increasing demands on Type II muscle fibers (fast twitch and fast oxidative glycolytic). Workplace Assessment It is clear that isometric strength testing cannot substitute for dynamic strength assessment when examining highly dynamic occupational job demands. As most industrial work tasks contain a significant dynamic component, analysis of isokinetic strength capabilities appears to offer some advantage to isometric testing in this regard. However, it must be recognized that isokinetic devices are not entirely realistic compared with free dynamic lifting in which subjects may use rapid acceleration to gain a weight-lifting advantage.

Jan 1, 1998

By C. K. Kocsis

A study was undertaken to evaluate the thermal environment and determine the contributing heat sources within the existing 153 Orebody of Coleman/McCreedy East Mine which would then enable the prediction of the climatic conditions in the mine?s future 170 Orebody. The study entailed continuously monitoring, for a 2-week period, the dry-bulb temperature, humidity and barometric pressure along the existing intake airways from surface down to the 4810 Level and throughout an active mining area on that level. Furthermore, the mining activities and associated equipment that could be responsible for any changes in the temperature and humidity conditions within this mining area were also monitored. These data were then used to develop and validate a climatic simulation of the mine?s mechanized cut and fill mining method. This climatic model was then transposed to the future 5700 Level in the deeper 170 Orebody, to determine the environmental conditions within its production workings and along the main haulage route ascending from that area. Based upon the simulations performed it was shown that the level of ventilation planned for the new orebody should be able to maintain adequate environmental conditions. However, this study did emphasize the importance of the appropriate distribution of airflow in workplaces that used auxiliary ventilation in order to sustain a suitable thermal environment.

Jan 1, 2009

By G Njowa

Mineral resource evaluation and estimation process is not an exact science; however it depends on the knowledge and experience of the competent person and his ability to apply his mind, make reasonable assumptions, interpretations and exercise sound judgment in the mineral resource estimation process. The mineral resource evaluation results in a mineral resource statement are disclosed to investors. The minerals industry is presently undergoing rapid changes in legislation governing the public reporting of mineral assets. It has gone through different phases of development with respect to the reporting of mineral resources and mineral reserves (mineral assets). In the past no reporting was done and currently mineral assets are reported as a supplementary section that briefly describes the mineral asset termed ?the mineral reserve and mineral resource statement?. The current industry trend appears to be going towards recognition and disclosure of the mineral assets on to the balance sheet. This paper explores the salient issues behind the mineral resources and mineral reserve statement of vein and reef deposits published in the public domain. It also highlights the potential misleading consequences of these issues and which filter through to the valuation of these particular mineral assets. The creation of reporting standards in the minerals industry has made significant inroads in standardizing and consolidating the interpretation and understanding of the different classification categories in the industry in an effort to promote common interpretation towards these salient issues.

Jan 1, 2008

By Francis Chartrand

The Kwyjibo deposit is an iron oxide Cu-REE-F-Mo-Au mineralization of Mesoproterozoic age located in the Grenville Province approximately 120 km NE of Sept-Îles, Quebec (Figure 1). Occurring along the SE margin of the Canatiche granitic complex, the deposit is composed of several polymetallic showings that are related to different textural facies of magnetite. The mineralization process at Kwyjibo is complex, and is divided into Early Granitophile, Magnetite, Main Polymetallic and Specular Hematite stages (Cayer et al., submitted for publication). The Main Polymetallic stage, comprising chalcopyrite, pyrite, fluorite, molybdenite and REE-bearing minerals, is superimposed on pre-existing magnetiterich rocks. Discovered by SOQUEM Inc. in 1993, the Kwyjibo deposit shares many characteristics with other hydrothermal polymetallic iron oxide deposits around the world. Foose and McLelland (1995) suggested that this class of mineralization could occur in the Grenville Province. However, only a few polymetallic occurrences are known to be associated with low-Ti iron oxide deposits in the Grenville. Kwyjibo is one of the most significant examples of a polymetallic iron oxide deposit to have been found in the Grenville Province to-date.

May 1, 2003

By B Mohanty, Y C. Lizotte

Optimization of blast fragmentation in underground hardrock mining requires analysis of its effects on loading and haulage equipment, together with the downstream materials handling system, with the objective of minimizing total mine operating costs. A methodology is reported which has been developed to quantify the actual fragmentation and equipment performance in the field. This is data which has seldom been practicable to capture nor received serious attention in mines. Based upon the experience gained in underground studies, a prototype standard is proposed which aims to summarize the pertinent data, collection and analysis for fragmentation assessment. This relates to parameters of direct measure, such as mean size and distribution, as well as muckpile and work environment. The paper concludes by defining the impact of fragmentation on the loading and downstream handling system.

Jan 1, 1991

By F. Bonnet, J. Lehmann, H. Gaye

A review of thermodynamic information and models of slags, including associated software when available, is presented. The pertinence and accuracy of these models is discussed by comparison of their predictions for various slag thermodynamic properties with the available experimental data. Practical industrial applications will be illustrated by a literature review of the dephosphorization process of ferromanganese alloys and by the description of Ti behavior during silico-manganese alloys production. This latter example will show how the thermodynamic models have been used to propose a flotation treatment at low temperature to enhance TiC removal.

Jan 1, 2004

By E. Bloomstein

The Lone Tree gold mine is located about 4S kilometers east from Winnemucca on the west flank of Lone Tree Hill in Humboldt County, Nevada. The deposit occurs at the north end of the low, rolling Havallah Hills and is about 1 kilometer south of Interstate Highway 80, in sections 11 and 14, Township 34 North, Range 42 East, Mount Diablo Base and Meridian (Fig. 1). The Lone Tree deposit is outside of any previously established mining district and all lands are owned or controlled by Santa Fe Pacific Gold or affiliated companies.

Jan 1, 1993

By Terry Braden

"Meeting probable world mineral demand in the years ahead will almost certainly require an ability to economically treat lower grade and more complex ores. Achieving this will require extensive research and technical development across the full spectrum of mineral processing.For mid-sized or smaller companies the most effective way to participate in such extensive programs - and gain access to the technology required to stay competitive - may be through collaborative research.This paper explores the recent history of collaborative research in mineral processing and in particular its ability to attract world-class multi-institutional research teams with sufficient resources to make step-change advances. It chronicles the advances achieved, but also explores the research architecture and administrative structures required to deliver research outcomes and technology transfer mechanisms to a range of often disparate sponsoring companies.INTRODUCTIONIn medieval times the dream of alchemists was to turn base metals into gold. We modern alchemists, of course, don’t waste our time on that sort of foolishness: we turn base metals into dollars. When I see the profit reports filed by some companies recently, I can only conclude that a lot of those present today must be pretty good at this.But the fact that we are here at this conference reminds us that an alchemist’s work is never done; turning base metals into dollars is not a one-trick wonder but an art that we must extensively refine year after year if we are to survive in a competitive marketplace.It is not that demand for metals is likely to slow; most people seem to think that China, India, Brazil and other emerging economies are still at the lower end of their demand curve. They will need significantly larger volumes of metals in the years ahead. The challenge for us as processors is that to supply increasing tonnages of those metals profitably we will almost certainly need to process more complex or lower grade ores and probably to do so with reduced energy inputs."

Jan 1, 2009