Search Documents

By Donald T. Robertson, Kurt Hecht, Michael K. Muchard

"This paper presents case histories of driven concrete pile damage detected with dynamic testing methods utilizing strain gages and accelerometers embedded in the pile at the prestressing yard during pile construction. Data from the embedded instrumentation is compared with data taken with external bolt on instrumentation and other test methods such as low strain testing on the same pile. In the most severe cases, the piles were extracted revealing and corroborating the embedded data collector results.INTRODUCTIONDynamic testing of driven pile foundations was originally developed in the late 1960’s and commercialized in the early 1970’s. While the methods of analyzing dynamic test data have improved with the advancement of computer technology, the test method and the sensors used to acquire the data have changed little. In 1998, under a research grant provided by the Florida Department of Transportation, (McVay et al, 2002) an Embedded Data Collector system (EDC) was developed. The collector utilizes two sensor packs, each consisting of one strain gage and one accelerometer, embedded near the pile toe and pile top. Utilizing the toe sensor pack, the system provides reliable real time pile end bearing capacity measurements. This end bearing capacity is combined with a Case Method Solution augmented with an automatic damping calculation to provide the overall pile capacity, pile skin friction capacity and pile end bearing capacity. Also, since the gages are embedded, they have the ability to track all changes from the casting yard (i.e. prestress), driving, and subsequent setup (freeze, relaxation, etc) at both the top and bottom of the pile."

Jan 1, 2017

By W. G. K. Fleming

Mr P. Bermingham introduced paper 9.1, describing the development and trials of a new pile load-testing technique that the Authors had termed "Statnamic". The system involved launching a test weight mounted on the head of the pile by igniting chemical fuel in a pressure combustion chamber between the pile head and the test weight. The expansion products from the burning fuel generated large pressures which were used to launch the weight upwards at high velocity. The reaction from this force generates an equal and opposite force at the pile head. This force is typically of much longer duration compared with, for instance, dynamic load testing by drop hammer. In addition the pile experiences a much lower acceleration - typically of less than one g. Because of the long duration blow, the pile is loaded at below its natural frequency and is therefore under a uniform high stress over its full length throughout the duration of the test. The pile behaviour is not dominated by the complex action of an impulsive stress-wave as with standard dynamic testing. The test technique is thus essentially quasi-static. It was anticipated that a ram test weight of 16 tonne would be sufficient to provide the test reaction for a 600 tonne load test. It was pointed out that the device was still at the research stage, but had yielded encouraging results to date. Testing would proceed from model testing and computer simulation to full scale field testing.

Jan 1, 1991

By Toshio Yonezawa, Helmut Florian, Herbert Kuh, Masamichi Aoki, Takao Koono, Franz-Werner Gerressen

"To increase the bearing capacity of the ground, soil improvement technique is often adopted. One advantage of soil improvement techniques is the fact, that the impact to the environment is low, as the system utilizes the existing soil. Recently, compressive strength of soil improvement gets more into the focus for the use of building foundation. To prevent brittle fracture, which is a weak point of soil improvement, fiber reinforced soil improvement has been developed. Laboratory tests were conducted to examine the fibers suitable for reinforced soil improvement, and examine the optimum mix design for fiber cement slurry. Based on the laboratory tests, polypropylene fiber and cellulosic viscosity admixture was selected. For the laboratory tests a scaled model of CSM mixing head was used to examine the dispersion of the fibers in the ground. Using the CSM mixing head, the outer periphery fibers of soil improvement seemed to be arranged in the vertical direction, toughness performance of the soil improvement could be improved. Furthermore, full scale field test was performed using actual CSM unit, modified to enable the use of fiber mixed slurry. The validity of the material as well as the toughness performance of the soil improvement, determined from lab test results, was confirmed. In addition, it was confirmed that fiber reinforced soil improvement can be constructed appropriately by CSM method.2 INTRODUCTIONSoil improvement technique to improve the strength and deformation performance of ground has been used for a long time. Cement improved methods, with the increase of the deep Mixing Method, which has been disseminated since the 1970's, was often used since. Cement used soil improvement technology has been utilized to stabilize excavations, slopes in embankment and much more. Recently, it can be used for preventing liquefaction by building soil improvement in a grid (Suzuki et al. (1996)), and also as basis of the structure by increasing the compression strength of soil improvement (Yamashita et al. (2011)). Cement used soil improvement method, a technique for mixing the in-site soil and cement, can effectively utilize natural resources, and it can be expected that its use will increase further in the future. Therefore, soil improvement technique will be able to minimize the impact on the environment. Cement improved soil is a mixture of soil particles and cement with high compressive strength but low tensile strength. Since tensile strength of soil improvement is low, brittle destruction occurs. Therefore, it is not possible to use soil improvement in conditions acting with bending stress. If a horizontal impact force occurs in the improved soil, the width of the soil improvement needs to be increased to reduce the bending stress. If preventing the brittle fracture of soil improvement, the width of soil improvement could be reduced, then less resources would be needed. In order to increase the tensile strength of the soil improvement, several studies for the mix of fiber and soil were performed. Victor (1992) indicates cracking deterrent effect by fiber based on laboratory tests. Moreover, based on laboratory tests, Hayasaki (1982) illustrated the effect on the tensile strength of the fiber types, the type of fiber, the diameter of and the length of fiber."

Jan 1, 2015

By Oladayo O. Komolafe and Majid Ghayoomi

p-y curves have been used over the years to determine the lateral resistance of piles. This method is popular among practicing engineers due to its simplicity and its ability to determine the slope, displacement, shear force, and bending moment for various depths along the pile. The ultimate lateral load resistance is a key component of p-y curve formulation. The p-y curve formulation by Reese et al. (1974) does not consider the effects of soil’s degree of saturation on theoretical ultimate lateral resistance of the failure wedge. This limits an accurate assessment of the lateral soil resistance near the ground surface and the consequent p-y curves. This paper extends the existing approach for determining the failure wedge in unsaturated cohesionless soils with suction dependency, especially for the depths that are above the water table within the wedge. The modification to the failure wedge analysis was made by considering the variation of the degree of saturation which affects effective stress and lateral earth pressure. Through a set of parametric analyses, the impact of incorporating principles of unsaturated soil mechanics in the estimation of theoretical ultimate lateral resistance is examined, and its implications on lateral pile response are discussed.

Sep 8, 2021

By Lawrence F. Johnsen, Marc J. Gallagher

"Micropiles are small diameter, bored, grouted-in-place piles incorporating steel casing and/or reinforcements. The omission of micropiles from most United States building codes has resulted in the application of varying standards for design and installation. The ADSC/DFI Micropile Committee has developed a proposed section for the 2006 edition of the International Building Code (IBC 2006) covering micropiles. The proposed IBC 2006 micropile code section is presented, along with comparisons to existing micropile codes and guidelines. A discussion section is provided to clarify sections of the proposed code. IntroductionMicropiles, defined as small diameter (typically less than 12 inches outer diameter), bored, grouted-in-place piles incorporating steel casing and/or reinforcements, are becoming common foundation elements for new construction, retrofits, and emergency repairs. Developed in Europe in the 1950's and used in United States practice since the late 1970's, micropiles are typically not addressed in building codes, particularly in the United States. As a result, micropiles are often reviewed by building officials to a variety of standards, including drilled shafts, caissons, cast-in-place bored piles, and concrete filled pipe piles. None of these adequately address the unique design and construction aspects of micropiles. Therefore, it became apparent to the foundation design and construction community that a micropile-specific code section was required.To that end, the International Association of Foundation Drilling and the Deep Foundations Institute (ADSC/DFI) Micropile Committee appointed a subcommittee in October 2003 to develop and submit a proposed micropile code section for the 2006 IBC. The subcommittee members included the two co-authors, as well as Tom Richards (Nicholson Construction Company), Tom Armour (DBM Contractors, Inc.), John Wolosick (Hayward Baker, Inc.), Allen Cadden (Schnabel Engineering) and Matt Niermann (Schnabel Foundation Company). At the time of the writing of this paper, the proposed code section has been presented at the IBC public hearing during which it was modified slightly. Final adoption (or rejection) will be determined by the IBC at the final action hearing in September 2005. The attached code section is the revised version following the public review hearings."

Jan 1, 2005

By Takeru Fukaya, Tsutomu Namikawa

"The bending tensile stress occurs in the ground improvements when external forces are applied to the column and wall shaped ground improvements. Therefore, in the design of the column and wall shaped ground improvements, the tensile properties of the cement-treated soils become a predominant factor when the external forces induce bending moments. Then the tensile properties are required to design the ground improvements rationally.Three points bending tests are conducted to investigate the bending tensile properties of cement-treated soils in this study. Cement-treated soils mixed in a laboratory are used in the bending tests. The test specimens are prepared with the several mixing properties to study the relationship between the tensile properties and unconfined compressive strength qu. Bending tensile strength Tfb and fracture energy Gf of the cement-treated soils are evaluated from the load-deflection curves obtained from the bending tests. The experimental results indicate that Tfb and Gf are approximately proportional to qu.INTRODUCTIONThe ground improvement by deep mixing has been widely used for structure foundations, retaining walls and liquefaction mitigations. Recently column and wall shaped ground improvements by deep mixing method have been applied for economical reason. When external forces are applied to the column and wall shaped ground improvements, the bending tensile stress occurs in the ground improvements. Therefore, in the design of the column and wall shaped ground improvements, the tensile properties of the cement-treated soils become a predominant factor when the external forces induce bending moments. Then the tensile properties are required to design the ground improvements appropriately.Namikawa et al. (2007) conducted the finite element analysis to investigate the dynamic behavior of the lattice-shaped improved ground for liquefaction mitigation. In the analysis, an improved ground consisting of several grids in a line was chosen to study the basic behavior of the lattice-shaped improved ground. Fig. 1 shows a example of calculated tensile failure zones in the improved soil during the earthquake. Half of one section of the improved soil consisting of two grids in a line for the 8 m × 8 m grid was modeled in the case. In Fig. 1, the failure occurs at the bottom and upper corners of the improved soil grid. The analysis result indicates that the constitutive model which can appropriately evaluate tensile failure behavior of cement-treated soils is required to evaluate the performance of the lattice-shaped improved ground for liquefaction mitigation. In the analysis, the elasto-plastic model developed by Namikawa and Mihira (2007) was adopted for the cement-treated soil behavior. The elasto-plastic model can suitably describe the tensile failure behavior of cement-treated soils. In the elasto-plastic model, tensile fracture energy is adopted to determine a tensile softening relationship because it is difficult to directly measure the stress-strain relationship after the peak stress state in direct tension tests. However there is little experimental study on the tensile fracture energy of cement-treated soils."

Jan 1, 2015

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Attasit Korchaiyapruk, Edward C. Clukey

"A deep mixing method (DMM) foundation was selected by the Project Team for a very large LNG facility in West Africa. As described in a companion paper, this foundation consists of a large number of columns installed by mixing cement with in-situ soils. The foundations are arrayed as a variety of honeycombed type configurations which, if installed to desired specifications, can provide a robust foundation alternative. The foundation is capable of distributing loads and limiting settlements even if some of the soil in the columns is not fully mixed during installation. An important part of the overall quality assessment program, therefore, involved developing a testing program to verify the methodology. In addition the impact of potential defects in columns on the overall foundation integrity had to be assessed. This paper describes some of the preliminary work done to establish the requirements for the quality assurance program. A key component of this program involved the sampling frequency used to assess potential defects in the columns. To verify the column integrity 104- mm samples were taken continuously at a selected frequency through the 23 m long columns. The preliminary work described in this paper demonstrated that the appropriate sampling frequency depends on both the desired reliability level as well as the number of defective columns encountered during testing.Initial finite element analyses were performed to assess the extent that defects could occur in columns within the honeycombed structure without adversely affecting the overall foundation integrity. The results from this work demonstrated that the spatial location of the defects was critical to properly assessing the foundation integrity.In addition to column sampling a load test was performed as part of the foundation verification process. The methods used to apply appropriate loads so that loads at the bottom of the columns approached design values are discussed in the paper.The results obtained from this preliminary study were then used to help develop a more comprehensive assessment program, described in a companion paper, to determine the robustness of the DMM foundations for both the LNG processing facilities and a condensate tank.IntroductionFoundations constructed with the Deep Mixing Method (DMM) can be an attractive and cost efficient alternate to other deep foundation options. This foundation is constructed by mixing soil and cement with an auger type drill. The foundation is usually constructed with a dual auger system that simultaneously creates two contiguous columns called foundation elements. Many elements are then arranged in a honeycombed configuration to create the overall foundation (Figure 1). A desired column strength can be obtained by varying the volume of cement added to the columns, the mixing rate of the soil and stroking sequence."

Jan 1, 2017

By Edward C. Clukey

A deep mixing method (DMM) foundation was selected by the Project Team for a very largeLNG facility in West Africa. As described in a companion paper, this foundation consists of alarge number of columns installed by mixing cement with in-situ soils. The foundations arearrayed as a variety of honeycombed type configurations which, if installed to desiredspecifications, can provide a robust foundation alternative. The foundation is capable ofdistributing loads and limiting settlements even if some of the soil in the columns is not fullymixed during installation. An important part of the overall quality assessment program,therefore, involved developing a testing program to verify the methodology. In addition theimpact of potential defects in columns on the overall foundation integrity had to be assessed.This paper describes some of the preliminary work done to establish the requirements for thequality assurance program. A key component of this program involved the samplingfrequency used to assess potential defects in the columns. To verify the column integrity 104-mm samples were taken continuously at a selected frequency through the 23 m longcolumns. The preliminary work described in this paper demonstrated that the appropriatesampling frequency depends on both the desired reliability level as well as the number ofdefective columns encountered during testing. Initial finite element analyses were performed to assess the extent that defects could occur incolumns within the honeycombed structure without adversely affecting the overall foundationintegrity. The results from this work demonstrated that the spatial location of the defects wascritical to properly assessing the foundation integrity. In addition to column sampling a load test was performed as part of the foundationverification process. The methods used to apply appropriate loads so that loads at thebottom of the columns approached design values are discussed in the paper. The results obtained from this preliminary study were then used to help develop a morecomprehensive assessment program, described in a companion paper, to determine therobustness of the DMM foundations for both the LNG processing facilities and a condensatetank.

By Chul Soo Park, Juhyung Lee, Duhyun Baek

"In this study the preliminary design of suction pile as the supporting system of the concrete floating structures was performed at the offshore pilot project area in Korea. The suction pile of the floating structures has to satisfy the lateral resistance against external force evaluated from the marine and structure conditions, as well as the penetration ability according to the soil and seepage conditions. In the design, the required penetration depths for lateral resistance were evaluated with different diameters of cylindrical steel suction pile, and the design suction pressures at each penetrating depths were assessed through the comparison of penetration forces and penetration-resistances. Finally, the optimal dimension of suction pile for the pilot project area was proposed.IntroductionInterests in sea spaces have rapidly increased around the world due to limitations in use of lands. Such increase has resulted in construction of numerous marine structures aimed at expanding the use of sea spaces and developing marine resources. South Korea also needs to secure construction technologies for floating infrastructures on its relatively deep seas. Foundations for floating structures consist of anchors and mooring systems rather than driven piles or cast-in-place piles, due to limitations in equipment operation or economic feasibility. Anchors and foundations used on the sea include drag anchors and suction piles, but the suction piles are more widely used for reasons regarding uncertainties of calculation of bearing capacity and construction. Large-diameter suction piles are generally used to utilize fully their penetration ability, which is proportionate to the square of the foundation diameter, and the length-diameter ratio (L/D) does not exceed 6 (Randolph et al., 2005; Andersen et al., 2005). Recently, a design and construction technology using group suction piles consisting of medium-diameter suction piles and concrete pile caps is being developed as an alternative to the conventional large-diameter mono suction piles. In addition, pilot projects involving the group suction piles of mediumdiameter are currently being reviewed for the southwest coast area in Korea. In this study, therefore, preliminary design for installation of medium-diameter mono suction piles as the supporting system of the concrete floating structures was performed, and suction pressures, penetration forces and resistances, and lateral loading capacity with diameters were reviewed."

Jan 1, 2017

By Yazn Khasawneh Ph. D. P. E., Will Tjaden, Spencer E. Ness P. E., Mohammed Nasim Ph. D. P. E.

Wind turbine components undergo many loading cycles during their operational life. Additionally, wind turbines may undergo extreme loading conditions from natural hazards, mechanical failures, or emergency stops. Current design practice for the foundations of wind turbines accounts for these complex loading conditions through a simplified pseudo-static approach based structural loading combinations. A rotational stiffness for the foundation is estimated from the pseudo-static analysis and then compared to an acceptable minimum rotational stiffness provided by the turbine manufacturer. These minimum rotational stiffnesses are based on dynamic analysis of the tower and nacelle system with the foundation represented as linear springs. This approach provides a reasonable approach to the foundation design but does not accurately capture the true dynamic performance of the entire soil-foundation-tower-nacelle system. This becomes especially important for pier-type foundations, which are being more commonly used to support modern and future generations of larger turbines. Additionally, the dynamic performance of the foundation will vary as the adjacent soil undergoes a large number of loading cycles of varying strain magnitudes. In this study, the full turbine-tower-foundation-soil system was modeled using finite element methods. An advanced non-linear soil constitutive model and dynamic loading time histories were used to investigate changes in stiffness of the soil, and the possible impact on the dynamic response of the system. Results were compared to conventional design methodologies with the goal of reducing foundation capital costs while avoiding increases in O&M costs and which can lower the LCOE of wind energy.

Oct 1, 2022

By James M. Tantalla, Roderic A. Ellman, W. Allen Marr, Scott R. Bamford

"Construction of the powerhouse for the Willow Island Hydroelectric Project required a 100-ft deep excavation inside the limits of a cofferdam and embankment-seepage cut-off wall through soil and rock adjacent to the Ohio River. Portions of the rock had preexisting weak plans and slickensided surfaces with low frictional strength. Stability analyses were performed for critical sections of the excavation to evaluate the stability of the soil slopes and rock cuts using buckling, tension crack, and limit equilibrium analysis techniques. Loading conditions included the 100-yr and intermediate floods, normal pool, sudden drawdown, and seismic design conditions.Stability analyses indicated adequate factors of safety for soil slopes and for rock cuts through the landside embankment sections. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated unacceptable factors of safety. Consequently, the riverside portion of the excavation required measures to increase stability. Long, high-capacity rock anchors and deep dewatering wells to lower the site piezometric head were chosen for this purpose.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. Required rock anchor loads varied from 1,968 to 2,074 kips. The designed anchors consisted of multiple, seven–wire strands with up to 59 strands per anchor. Bond lengths used an allowable bond stress of 100 psi based on the rock bond measured with pull-out tests. Maximum bond and anchor lengths were 50 ft and 140 ft, respectively. Measurements of forces in selected strands and displacements of the excavation showed excellent performance."

Jan 1, 2017

By Dennis Wrixon

It was a little bit exceeded. The decision was the uniform settlement is measured at each one corner and the highest one corner is the important one. And in addition there is a differential settlement of 2.1 mm allowed. So we reached about 7.8 or 7.9 mm with the highest corner and in addition 2.1 so it was a little too much. But behind there is a very difficult calculation of the authorities where all of the displacements are combined together and there are of course some more factors of safety in these settlements.

Feb 10, 2003

By Thomas Kennedy, Michael Bennett

"History never repeats itself, but it often rhymes." The old aphorism reflects how the study of the past may, perhaps, be most widely valued when it can be used to improve current and future decision making. The education the authors received as geotechnical graduate students certainly impressed upon them the importance of recognizing that not all wisdom is necessarily new. Much of their graduate coursework involved reading technical papers that had introduced concepts of outstanding historical significance in the field, such as pore pressure coefficients, stress paths, and the stress history and nor- malized soil engineering model. These papers gave the authors both respect for and interest in the historical develop- ment of the field. After graduation, the authors furthered and deepened this interest by continuing to expand their knowledge of the profession through both experience in practice and the review of additional literature.

Jan 1, 2023

By Olgun

Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.

By C. Guney Olgun, Charles Elks, Sherif L. Abdelaziz, James R. Martin, Christopher Fox, Pier Luigi Iovino, Fatih Catalbas, Pierre Gouvin

"Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.IntroductionThere is a developing trend around the world to explore alternative energy sources. The main driving forces are growing global energy demand, depleting natural resources and the adverse effects of greenhouse gas emissions from fossil fuel consumption. Geothermal energy is one of the promising renewable sources that can be utilized to offset such trends. However the use of geothermal energy has been limited mainly to certain hot spot areas where it is used either for district heating and/or electricity generation. Ground temperatures below a depth of about 6 meters (20 feet) remain stable compared to outside air temperatures, typically lying between 8-23°C (46-73°F) at most U.S. regions. The constant temperature and heat storage capacity of near surface soils in any region represent a tremendous potential of stored energy that can be used for heating and cooling of structures."

Jan 1, 2017

By Maral Papazian Bedian

"Case 2. 100th Street Bus Depot: Elimination of Deep Caissons in Favor of Spread FootingsThe PROJECTThe 100th Street Bus Depot is a new five-story bus terminal for the New York City Metropolitan Transit Authority occupying one city block in Manhattan between 99th and 100th Streets, and between Lexington and Park Avenues. It replaces a former two-story garage, built in the 1890’s and initially used as a trolley-car barn. The new structure is a steelframed building with concrete floors and includes a partial basement near its middle. The easternmost column line with design loads of 10 MN (1,125 tons) is within 1.5 m of the underlying multi-tube Lexington Avenue subway system. To support the new columns along the subway line, the project bid plans had called for 1 m diameter and 17 m deep drilled shafts. The upper 14 m of each unit would have required 50 mm separation from the surrounding rock to prevent stress from being imposed on the roof and walls of the adjacent tunnel. The column loads were thus transferred to below the base of the tunnel and supported by 3 m long sockets in bedrock. The bid documents contained extensive test boring information, which revealed that the project site was underlain by massive Manhattan Mica Schist bedrock within just 3 m below street level. In fact, the Lexington Avenue two-level and multi-tube subway had been tunneled through this rock circa 1910, leaving an about 6 m thick solid roof over the upper-level subway. The NX rock core recovery values were near 100 %, with average RQD of 75 %.The CHANGEThe Bus Depot project was let as a design/build contract with a very aggressive fast-track schedule. Both the pre-bid preliminary design and the subsequent final design by the Contractor’s own hired design engineers relied heavily on very restrictive codes, including unnecessarily conservative approaches to seismic design. Any suggestion for value engineering change was undesirable and was strongly resisted. Yet, objecting against the blind reliance on codes in foundation design, the author questioned the real need for the deep drilled shafts to support the columns along the subway. The unsupported statement that no stresses from the new structure can be imposed on the roof and walls of the adjacent tunnel was not sufficient reason for the drilled-shaft design. Unconvinced that deep shafts were necessary, the author rushed to MTA’s warehouse where many rows of rock core boxes were neatly stacked. Careful inspection and some simple testing of the rock cores with the blows of a geologic hammer gave support to the reservations about the design. Later, as expected, the schist bedrock at this site was found to be hard to very hard with unconfined compressive strength values estimated to range from at least 70 MPa to over 100 MPa (10,000 psi to 15,000 psi). The tensile strength of the rock was assessed to be minimum 5 MPa (750 psi)."

Jan 1, 2003

By John C. Ryan

The Emeca Pile Splice, an innovative mechanical prestressed concrete pile splice, is the first robotically welded splice to be fabricated in the United States. An analytical and experimental study was conducted to establish the capacity of the standard splice for 12-in. and 14-in. square piles. The study illustrates compliance of the splice with International Building Code (2006) requirements. A case study for a large petroleum tank foundation project in Port Canaveral, FL is presented, demonstrating the efficiency achieved through use of spliced-piles. For the case-study project, single-piece 18-in.-square, 100-ft-long piles were replaced with 12-in.-square, two-piece, spliced piles. As a result, a significant reduction of material, labor, handling, and equipment was documented for the project. Savings realized on the installed pile cost was estimated to be in excess of 30% by the owner.

Jan 1, 2010

By A. Felipe Uribe-Henao, Camilo Ballesteros, Luis G. Arboleda-Monsalve, David G. Zapata-Medina

Conventional excavation analysis based on total or effective stress methods can result in inaccurate estimation of ground movements when impervious soil conditions or rapid excavation sequences are not found in the excavation (i.e., assumption of undrained response is not valid). The influence of excavation rate, hydraulic conductivity, and excavation geometry on the fully coupled solid-fluid behavior of a braced excavation in cohesive soils are studied parametrically using PLAXIS2D. The coupled excavation analysis is performed using the Hypoplasticity clay model to reproduce the constitutive behavior of soil and the poro-elasticity Biot’s theory to account for changes in pore water pressure due to deformations in the soil skeleton. Results obtained from the parametric studies indicate that excavation rates to hydraulic conductivity ratios, ER/k, smaller than 0.1 and larger than 104 can be used as limits for drained and undrained analyses, respectively. In practical applications, undrained and partially drained excavation analysis with ER/k larger than 102 resulted in a similar ground deformation. However, smaller ER/k ratios demand fully coupled solid-fluid analysis. An analytical method aimed at predicting excess pore water pressures and determining the required type of analysis associated with soil and excavation conditions, e.g., drained, partially drained, and undrained analysis, is proposed herein to accurately estimate the ground movements induced by the excavation.

By Tony Amis, Marco Barla, Alice Di Donna

"Energy geostructures are becoming an increasingly popular solution around the world for Developers looking to reduce CO2 and system running costs. Energy geostructures are geotechnical structures that provide both the important role of structural stability while also acting as a heat exchanger with the ground, enabling the supported buildings and or infrastructure to be heated and cooled using the principle of low enthalpy geothermal systems. The main advantage of this innovative technology with respect to standard geothermal plant is the reduction of the initial installation costs and construction schedule benefits, compared to installing conventional geothermal solutions, largely due to the additional use of structures which would be constructed in any case. However, it is important with respect to energy geostructures that additional aspects need careful consideration. For this very reason, several research studies have been carried out over the last decade on this subject and a number of real case studies have been monitored and analysed. The key difference with respect to conventional shallow geothermal systems are mainly related to the geometry, which is imposed by the geotechnical project, and the need to ensure that the primary structural role is always guaranteed. Special boundary conditions, the reduced depth, the influence of atmospheric external temperature can also play an important role for energy geostructures. They can affect, both energy efficiency and, the geotechnical behaviour because of the possible thermal induced mechanical effects. This paper presents a picture of the current situation regarding energy geostructures and their peculiar features, and collects available data to provide a reference framework. Data has been collected from literature and personal communications and then processed to provide easy-to-read charts useful for practical consultation at a glance. This paper provides, an indication of the distribution of such systems worldwide, their spread in time, and a global view of their actual efficiency from the structural, energy, economic and environmental point of view.1. IntroductionEnergy geostructures are becoming an increasingly popular consideration around the world. Energy geostructures are geotechnical structures with a dual role of providing structural stability and the ability to exchange heat with the ground, to provide low carbon heat and coolth to supporting and or adjacent buildings and infrastructure, using the principle of low enthalpy geothermal systems (Barla and Di Donna, 2016; Laloui and Di Donna, 2013). A closed circuit of high density polyethylene (HDPE) pipes is embedded in the concrete, and a heat carrier fluid circulates through them exchanging heat with the ground. The HDPE pipework circuit inside the geostructure is linked to one of the above buildings or infrastructure through a heat pump, which adapts the temperature of the circulating fluid to the heating (winter mode) and cooling (summer mode) needs. In this way, heat can be injected into the ground during summer and extracted from it during winter. In principle, all structures in contact with the ground can be used as energy geostructures. The first examples of energy geostructures date back to the eighties in Austria and were mainly piles and shallow foundations. A decade later, Henderson et al. (1999) reported on what would appear to be the first successful use of geothermal energy piles in the US, with loops incorporated into the foundation for a hotel in Geneva, New York. As was their use in this New York case history, the typical geothermal energy pile application is used in conjunction with additional closed loop boreholes to provide the required energy capacity for a structure. Interestingly the report concludes that the geothermal energy piles had a better heat transfer performance than the borehole field. The first energy walls appeared slightly later, while still today only a few experimental cas"

Jan 1, 2017

By Abolfazl Eslami, Sara Heidarie Golafzani

CPT-based methods considered as complementary tools for static analyses outperform other axial pile bearing capacity predictive methods. Considering soil spatial variability and minor errors associated with procedure and operator, CPT-base methods mitigate the effect of latent uncertainties in pile design. These methods were developed based on different databases and purposes. Hence, several statistical and probabilistic attributes were defined and implemented to assess the predictive CPT-based methods’ performance via CPT and pile databases in terms of the model parameter. These features make a comparison among methods in terms of precision, accuracy, and efficiency. Furthermore, CPT-based methods can be subjected to scrutiny over their backgrounds and how they were developed via reliability analysis. In this regard, a database of sixty-two driven piles and their adjacent CPT soundings were gathered, and six commonly applied CPT-based methods were examined according to criteria other than prevailing statistical and probabilistic ones, including; (a) input variables, (b) soil behavior classification (SBC) (c) model assumption (d) Influence zone, and (e) axial loading direction. According to these introduced criteria, CPTbased methods were classified and appraised via efficiency ratio. Eventually, these reliability-based, statistical, and probabilistic criteria evaluate the understudied methods performance for the investigated compiled database and help designers select consciously appropriate predictive methods according to the site conditions.

Sep 8, 2021