Search Documents

By M BSckstr÷m

Acid rock drainage (ARD), commonly found in vicinities of sulfidic mines, possess properties capable of widely affecting the surrounding environment by acidification and heavy metal pollution. In most ARD treatments, various alkaline sources are used to neutralise the acid produced. Utilisation of highly alkaline fly ashes instead of raw materials is a cost-effective alternative, which lately have become increasingly popular. In laboratory batch experiments, neutralising capacity of fly ash was studied during 20 days. ARD was added to the fly ash once a day, for each increment the liquid to solid ratio (L/S ratio) was increased. At an early stage of the experiment (day 6, L/S ratio 12), the concentration of barium in solution unexpectedly increased by a factor of 50 (from 200 to 10 000 ¦g+l-1). This high concentration also sustained the following two days (L/S ratios 14 and 16) before dropping to the original level. pH showed a slight increase during these observations (pH 12.4 - 12.7). The phenomenon was also observed in a parallel and identical series. In addition to barium, aluminium and strontium clearly increased in the same manner, however not as much as barium. Furthermore, concentrations of chromium and molybdenum noticeably decreased at these distinct L/S ratios (12, 14 and 16). The behaviour of barium and subsequently strontium, aluminium, chromium and molybdenum is only partially understood. The decrease of chromium and molybdenum is suggested to be due to incorporation into the interlayer regions of hydrocalumite (Ca4Al2(OH)12(OH)2+6H2O), replacing the hydroxide groups, which also explains the increase in pH. Moreover, the increase of barium, strontium and aluminium could be attributable to dissolution of the silicate mineral celsian (Ba,Sr(Al2Si2O8)). Alternatively, barium and strontium increase could be explained by dissolution of a Ba,Sr(SO4)-solid solution and aluminium increase by dissolution of hydrocalumite or ettringite.

Jan 1, 2008

By P Klaric

Drive stability is critical in block/panel cave mining. The production levels of these mines are required to remain operational for the entire life-of-mine which can be in excess of 30 years. It is therefore necessary to produce high-quality drives to ensure sustainable mine productivity. In order to improve the quality of drives and pillars, this gold mine instigated a project to optimise their development blasting. The initial aim was to reduce the level of overbreak in development mining, which was averaging approximately 18 per cent. The benefits of controlling overbreak not only included an increase in the integrity of the drives but also a decrease in load and haul and ground support costs. Through focusing on the optimal blasting of the perimeter holes, overbreak was reduced to 4.5 per cent. The project’s focus then moved to drill and charge designs for development faces. In optimising these designs, it was anticipated that improvements in the development mining cycle would be achievable.CITATION:Klaric, P, 2015. Improving drive stability through efficient development blasting design and practices, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 327–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Ji Fang, Chong Fan, Fengrui Wang, Dongxin Bai

Unmanned mining technology in underground mines offers high efficiency, safety, and low cost. However, ground operators face challenges in accurately perceiving the underground environment through videos. This paper presents an augmented reality (AR) platform developed to enhance the unmanned mining process. The platform uses cameras and 5G technology to transmit high-fidelity video streams to the ground, where key targets are identified and virtual models are registered in the video to enhance the real scene. Tests in the Xinli stope of the Sanshandao gold mine showed the platform’s effectiveness in improving ground operators’ perception and production efficiency.

Jan 30, 2022

By Carlos Alberto Sanchéz

El presente trabajo describe la realización del monitoreo de zonas revegetadas de cierre de minas utilizando técnicas de teledetección espacial. El estudio evaluó las áreas iniciales del programa de revegetación final de la minera Yanacocha. Las áreas de estudio son Maqui Maqui y San José, se localizan en la zona este de operaciones y se encuentran en cierre desde el año 200 y son restauradas dentro del programa de revegetación de áreas finales de la empresa. Como parte de la medición del éxito del programa se realiza el monitoreo de las mismas utilizando estas nuevas tecnologías. Por ello, es aplicable como parte de la conducción de los programas de revegetación de los planes de cierre de minas.

Sep 12, 2005

By K. T. Aust

The occurrence of annealing twins in high-purity aluminum resulted in the formation of grain boundaries having orientation relationships which correspond to a high density of coincidence sites. The results provide support for the coincidence site model and indicate that large-angle coincidence boundaries have lower free energies than large-angle noncoincidence boundaries. Observations are presented concerning the coherent structure of twin interfaces in aluminum and the importance of inter-facial energy in preferred orientation. RECENT experiments1 have shown that when an annealing twin is formed during grain boundary migration in zone-refined lead, a large-angle random boundary is replaced at the growth front by a large-angle coincidence site boundary. The coincidence site orientation relationships obtained by twinning were of the type considered by Kronberg and Wilson,2 Frank,3 and Dunn.4 On the basis of the theory of annealing twins advanced by Fullman and Fisher,5 these observations indicate that the energy of a coincidence site boundary is less than the energy of a random boundary by an amount which exceeds the energy of the coherent twin boundary. This energy difference between the coincidence and random boundaries must be at least about 5 pct since the ratio of twin boundary energy to grain boundary energy in zone-refined lead is 0.05 * .014.6 Fullman7 has found that the twin boundary energy in aluminum is about 21 i 5 pct that of a large-angle grain boundary. A twin boundary energy as large as this would be expected to exclude the formation of many coincidence site grain boundaries, especially those which have a relatively low density of coin- cidence sites. Therefore, if the coincidence site model is a useful interpretation of certain large-angle boundaries, then it would be predicted that only coincidence boundaries which separate adjacent crystals with a relatively high density of coincidence sites may be obtained as a result of twinning in aluminum. The present experiments provided a means of testing this prediction since annealing twins occurred during the growth of recrystallized grains into striated, melt-grown single crystals of zone-refined aluminum. EXPERJMENTAL PROCEDURE A striated single crystal of zone-refined aluminum, about 1 cm sq and 37 cm in length, was obtained during zone melting of aluminum of 99.996 wt pct starting purity in a graphite boat under helium atmosphere.8 A molten zone of 2 to 3 cm in length, which was maintained by induction heating. was passed along the length of the bar for eleven passes at a rate of 0.9 mm per min. An additional final pass was given at a rate of 0.2 mm per min. The center portion of the zone-melted bar was characterized by an electrical resistivity ratio between room temperature and 4.2° K of 8000 to 9000. Single crystals of 1 to 2 cm in length were removed from the center section of the zone-refined bar and electrolytic ally polished in a 2:l solution of methyl alcohol and concentrated nitric acid. The specimens were then chemically polished in Alcoa R-5 solution. X-ray analysis of the single crystals indicated the presence of striations or lineage substructure having misorientations as high as 2 deg. New, recrystallized grains were introduced into each striated crystal by the technique of artificial nucleation and growth, previously described.9 During the growth of the recrystallized grains at 300' to 600°C in argon, it was sometimes found that a

Jan 1, 1962

What is a nugget effect? In the early development of geostatistics, the term ?nugget effect? was coined for the apparent discontinuity at the beginning of many semivariogram graphs. This name was chosen to reflect the large differences found between neighbouring samples in ?nuggety? mineralizations such as Wits gold reefs. Geostatistical theory assumes that the difference between a sampled value and a potential repeat sample at the same location is actually zero. Included in this ?nugget effect? would be true variation between contiguous samples due to the nature of the mineralization, micro-fracturing, nugget or crystal size, and so on. Also included in the nugget effect would be any ?random? sampling variation which might occur due to the method in which the sample was taken, the adequacy of the sample size, the assaying process, etc. Arguments were put forward that ?sampling errors? actually exist at zero distance. Some geostatistical schools actually maintain that the ?nugget effect? is all sampling error. This would imply that ?perfect? sampling would eliminate the nugget effect entirely. There is now a dichotomy both in the geostatistical world and in the software packages provided for geostatistical analyses. It may seem academic to argue over whether the semivariogram model should take a value of zero, a value equal to the nugget effect, or a partial value at distance zero. However, the decision can have a profound effect on both the estimated resource and in our confidence on that resource. Whereas most geostatistical texts define the semivariogram model as taking the value of zero at zero distance, others imply that the full nugget effect should be used at zero distance. For example: ?The nugget effect refers to the nonzero intercept of the variogram and is an overall estimate of error caused by measurement inaccuracy and environmental variability occurring at fine enough scales to be unresolved by the sampling interval3 ?Christensen4 has shown that the ?nugget effect?, or non-zero variance at the origin of the sernivariogram, can be reproduced by a measurement error model ?The nugget effect is considered random noise and may represent short-scale variability, measurement error, sample rate, etc.5. In many training texts and Web courses, the definition of the semivariogram is ambiguous as the formulae for semivariogram models is not actually specified at zero distance6,7,8.

Jan 1, 2010

By R C. Schodde

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Over the last decade (2005–2014), a total of 439 significant deposits of gold and base metals were found in the world. Twenty (or 4.6 per cent) of these deposits were in the Pacific/South-East Asia (Pacific/SE Asia) region. In terms of contained metal, the region accounted for 1.6 per cent of gold and 13.8 per cent of copper found in the world. With regard to nickel and zinc/lead, the region’s contributions were insignificant.Over the same period, the Pacific/SE Asia region accounted for 6.6 per cent and 12.6 per cent of all gold and copper exploration expenditures in the world respectively. After adjusting for by-product credits, unreported discoveries and likely growth in resource, the unit discovery cost for the region was US$199/oz (compared to a world average of US$50/oz). For comparison, the unit discovery costs for the previous decade were US$55/oz and US$25/oz respectively. The region’s unit discovery cost for copper was US$0.036/lb (versus a world average of US$0.040). For comparison, the unit discovery costs for the previous decade were US$0.026/lb and US$0.008/lb Cu respectively.The region’s mediocre discovery performance doesn’t reflect its distribution of known mineralisation. Some countries within the region have a very good endowment per square kilometre.It is noted that the intensity of exploration (and resulting success) would be boosted if governments provided a more mining- and investment-friendly business environment and generated better precompetitive geological data sets (to identify new exploration targets and boost the country’s perceived mineral prospectivity). A multivariable regression analysis of a decade of data from the Fraser Institute’s mining company surveys found that a ten point increase in the Policy Perception Index or a 0.1 point increase in the Mineral Potential Index could boost (in the short term) exploration expenditures by 1.9 per cent and 2.7 per cent respectively. The resulting economic benefits of an expanded mining sector would be significant. The same story applies elsewhere in the world.CITATION:Schodde, R C, 2015. Discovery performance for gold and base metals in the Pacific/South-East Asia – 2005–2014, in Proceedings PACRIM 2015 Congress, pp 25–34 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By A. Juganda, F. WILSON, G.E. BOGIN, H. PINHEIRO, N. SANDOVAL, J.F. BRUNE

To evaluate methane explosion hazards in underground longwall coal mines, researchers at the Colorado School of Mines developed a computational fluid dynamics (CFD) model along with a 1/40th-scale, optically accessible, physical model of a longwall mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met to accurately represent the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure and gas concentrations. This research will help develop strategies for methane monitoring to prevent methane ignitions and explosions in longwall coal operations.

Dec 1, 2022

By Rodrigo Costa dos Santos

O objetivo deste artigo é apresentar uma proposta de metodologia para auxílio na fase de planejamento de um projeto de manutenção, objetivando a redução de falhas no mesmo. Tal estudo possui relevância, pois quando se trata de manutenção preventiva o custo é sempre considerável para qualquer empresa, uma vez que para realização as máquinas devem ser paradas e recursos humanos e materiais devem ser disponibilizados, desta forma o planejamento deve ser feito de maneira que sejam utilizados apenas os recursos necessários e suficientes para manter a qualidade dos equipamentos. A metodologia se embasa na teoria geral de projetos e utiliza de maneira sequenciada e estratégica ferramentas já aplicadas no mundo da manutenção para determinar as oito fases personalizadas para um evento de manutenção. A aplicação da metodologia facilita o trabalho do planejador o que consequentemente viabiliza a sua entrada no meio industrial, posto que a metodologia é altamente simples e sequenciada, o planejador não precisa conhecer com detalhes a teoria de projetos para utiliza-la. Portanto, com objetivo de facilitar e sequenciar o planejamento da manutenção afim de reduzir falhas, a metodologia trabalha de maneira forte a análise e gestão de riscos e definição de cronogramas em projetos.

Oct 30, 2017

By Kenneth E. Hay

Researchers from the U.S. Bureau of Mines conducted a field study to assess the safety of remotely controlled mobile roof supports (MRS) in a retreat pillar mining operation, Data were collected to provide the Mine Health and Safety Administration with criteria needed to develop guidelines for MRS use and to determine if precursors could be identified that would alert miners to imminent roof falls. Two test sites at which two different support methods-MRS's and posts were used and were monitored to obtain information on entry stability. Pressure transducers and string pots were installed on all four MRS's to obtain loading and displacement information. and roof bolt load cells. sonic probes, extensometers, and survey targets were installed in the surrounding entries to obtain information on ground behavior. Results showed a larger increase in roof bolt loading and roof movement when MRS's were used, especially in the intersection area. Roof bolt loads in the entries showed decreases in load when the MRS's were set and increases up to 11,1 kN (2,500 lbf) when the MRS's were unloaded. Unloading of one MRS in a pair did not significantly increase load on the other. MRS's I and 2 usually had the higher loads, with these loads increasing as the pillars on each side were being mined. MRS 3 normally had lower loads than I and 2: however, it also experienced some very high loads when in the last position near the pushout. MRS 4 usually had the lowest loads, primarily because it was located near the solid pillar that was not being mined.

Jan 1, 1995

By C Thompson, D Connelly

The history of mill liners has evolved over time and this paper tracks the changes and development of liner technology. It provides an overview of the primary types of liners, the design and the materials of construction. The design of a mill liner is driven by application, materials of construction, casting technology and handling issues. The choice of solid steel, grid liners, rubber or composites and magnetic liners is based on many factors.The methods used for monitoring wear and predicting eventual change out time are many and varied. The contribution of discrete element modeling (DEM) analysis in predicting wear profile is discussed.Mill trajectory and DEM software programs are used with great effect to predict the effect of lifter height, face angle, high low lifters or mill speed. In the field, trial and operational experience is used or improvements/design concepts at one operation are applied to another. Broken mill lifters, accentuated wear and other problems can be better understood using hardness testing, chemical analysis and photo micrograph analysis of pearlitic or martensitic structure along with fracture face observations. This forms a part of the typical root cause analysis. However given correct and sound liner and lifter, feed and discharge design media selection, and materials of construction, the majority of premature liner or bolting failure is normally attributed to incorrect operational methods such as excessive high ball to feed ratio, incorrect mill speed relating to lifter ball throw, incorrect media selection, "tramp" material entering the mill charge from upstream or recirculating process and understanding the specific mill operation in question.It is hoped that this paper will benefit mill operators who are faced with challenges of improving wear life and at the same time optimizing mill throughput and performance.CITATION:Connelly, D and Thompson, C, 2013. The selection design and application of mill liners for large wet grinding mills, in Proceedings MetPlant 2013 , pp 133-140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds ;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2 : I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resins may serve as a habitat of microorganisms. In the decomposition of a medium. some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17, 32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

Sufficient time has elapsed since the enactment of the amendments to the mining legislation in 1981 to enable an examination to be made of the way in which the licensing system operates in practice. One of the most important decisions in resource management in New Zealand is whether or not rights of access to the resource should be conferred by the Crown upon an appropriate private sector participant. The licensing system is the means for allocating these rights of access. The manner in which the licensing system is administered, therefore, is crucial to natural resource management in New Zealand. What is the mining licensing system in New Zealand designed to achieve? This simple question admits of no easy answer. Is it the identification and development of the mineral resources of New Zealand? Are these objectives tempered by issues of resource conservation and environmental protection? Is a balance to be achieved among these competing factors? Does the legislation contain any priorities? Does the system respond in an ad hoc manner to particular facts and circumstances or does it operate within a more predictable framework? To what extent are decisions made on access to minerals with reference to the development or conservation of other resources? These questions may be summarised in the title to this paper which poses the question whether mining licences are instruments for resource management.

Jan 1, 1988

Organization Place Date 1917 American Institute of Architects Philadelphia,.,; Pa. Dec. 26-29 American Society of Mechanical Engineers New York City. Dec. 26-29 American Mining Congress State Chapter Phoenix, Ariz. Dec. 26-29

Jan 11, 1917

By Alastair M. Lumsden

A study was initiated to examine the ways in which a number of foreign countries classify and regulate metal/non-metal mines which experience problems due to naturally-occurring flammable gases. Twenty countries were selected for study, and useful information was obtained from sixteen of these. Nine countries were visited (five of them twice) to hold meetings with representatives of government mine regulatory agencies and mine operators, and to visit mines encountering methane and other gases (carbon dioxide, nitrogen). In the later stages of the study seven gassy metal/non-metal mines in the United States were visited so as to provide a basis for comparison, and hence the evaluation of both the U.S. and foreign gassy mine regulations. In addition to obtaining copies of the mining laws and regulations of a number of foreign countries, nine foreign gassy mines, and the seven in the United States were documented in as much detail as possible. All this information is presented, along with appropriate conclusions and appendices. The study took two years and three months to complete.

Jan 1, 1983

By André Vien, Pedro Gonzalez, Julio Palomino, Rob Perry

"In many mineral processing plants ore is reclaimed from a stockpile using multiple feeders. The discharge from these feeders is combined onto a single conveyor from which total tonnage is measured. Typically, operators set feeder output ratios to adjust the proportion of total tonnage drawn from each feeder. From a process control perspective, this system is not easy to control because the response time of each feeder depends on the distance from the feeder to the weightometer. This paper proposes a simple and elegant process control strategy to manage feeder ratio changes and the associated long and varying process dead-times. Changes in feeder speed are delayed and filtered to compensate for transport delays between feeders. The strategy was evaluated by simulation and installed on a mill feed system.ResumenEn numerosas plantas procesadoras de minerales, el mineral es extraido desde una pila de almacenamiento usando varios alimentadores. La descarga de estos alimentadores es recibida por zinica correa transportadora, en la cual se mide el tonelaje total. Comzinmente, los operadores colocan un valor determinado en cada controlador de razdn para ajustar la proporcidn del tonelaje total extraido por los alimentadores. Desde el punto de vista del control automatic0 de procesos, este sistema es dijkil de manejar debido a que el tiempo de respuesta de cada alimentador depende de la distancia de este respecto a la ubicacidn del pesdmetro. Este trabajo, propone una estrategia de control, simple y elegante, para compensar los cambios de razdn a cada alimentador y los tiempos muertos del proceso largos y variables. Los cambios en la velocidad de los alimentadores son retardadas y filtradas para compensar los retardos del transporte entre alimentadores. La estrategia fue evaluada por simulacidn, instalada y probada en un sistema de alimentacidn a molino."

Jan 1, 2000

By Eliane Hirata

En el año 2016 se identificó que el 79% de los trabajadores propios y terceros de Nexa presentaban al menos un riesgo relacionado con el estilo de vida, lo cual incentivo a que se buscaran programas que promovieran la calidad de vida. Por ello, en el año 2017, se impartió el programa de calidad de vida, el cual se enfoca en los pilares establecidos por la OMS para calidad de vida que son físico, psicológico, ambiente, relaciones sociales, autonomía y creencias. Así mismo, este programa estaba alineado con el OBS 3 - Salud y Bienestar, el cual busca garantizar una vida sana y promover el bienestar en todas las edades.

Sep 30, 2022

By K. Kavouridis

The energy and climate protection policy of European Union (EU), and its Member States adopted in 2007 bridges security of supply, environmental protection and competitiveness. The objectives of the EU energy and environmental strategy cover the foreseeable period till 2020. It assumes all sources of energy will be needed. The objectives for renewable and improved efficiency are ambitious; it must be established if they are also realistic. Coal can continue to make valuable contribution to the security of supply and low price of electricity, only with technologies allowing for drastic reduction of the CO2 emitted of its combustion. The aimed at -20% reduction of green-house gases (GHG) of EU-27 by 2020 is an objective limited in time and content. Europe produces less than 15% of global CO2 and this will be reduced to 10% in 2030. Emissions Trading (ET) is to remain the central instrument for CO2 management, especially in the power sector. ET scheme (ETS) or other mechanisms need designing to create an incentive for investment in higher efficiency and technologies and to Carbon Capture & Storage (CCS). The ETS as the climate protection instrument of the EU can become a heavy burden (high fuel and electricity prices, less security of supply) or it can create a climate for modernization of fossil fuel power plants. The suggestion in this paper of fuel-specific benchmark system for CO2 allocation after 2012 can combine the emission levels to be reached with a strong drive to invest, the necessary investment security, transparency and the principle of proportionality. A Benchmark System as recommended by coal industry could adapt to the different circumstances in the long term and comply with EU energy and environmental policy objectives.

Jan 1, 2008

By L. C. Graton, Joseph Murdoch

I. Introduction......................... 26 1. The Relations of Scale in Geologic Work........ 26 2. General Characteristics of Copper Sulphide Ores..... 29 3. Scope of Present Study................. 31 11. Description of the Important Minerals............ 36 1. Pyrite....................... 36 2. Pyrrhotite....................... 41 3. Chalcopyrite...................... 41 4. Bornite........................ 40 5. Covellite....................... 50 6. Chalcocite....................... 52 7. Enargite...................... 59 8. Tetrahedrite and Tennantite.............. 61 III. Conclusions.......................... 62 I. Introduction. The Relations of Scale in Geologic Work. Many features of human accomplishment rest upon the possibility of representing natural objects on a scale of different magnitude from the actual one. Most drawings, for example, are of very different scale from that of the object depicted, and indeed are useful mainly 011 this account. More important than the question of mere convenience, however, is that of meeting the physical limitations of vision.' Thus, a mural

Jan 1, 1914

By Cínthia Toshimi Ogata

Processos de fundição de ligas de alumínio com altos teores de Mg são um desafio da indústria, uma vez que diferentes taxas de resfriamento ocorrem em geometrias diversas. Este trabalho tem como objetivo caracterizar a liga de alumínio AA5052 com variações em teores de Mg por meio de experimentos de solidificação direcional transitória, e compreender seus efeitos com relação a evolução de parâmetros térmicos, microestruturais, e propriedade mecânica. As leis experimentais de evolução do espaçamento dendrítico primário (?1) com relação a taxa de resfriamento resultam em: ?_1=640 ?T ?_L?^(-1/4) para a liga 5052 com 2,4%Mg e ?_1=300 ?T ?_L?^(-1/4) para a liga com 3,2%Mg. As leis de crescimento de espaçamento dendrítico secundário (?2) com relação a velocidade de solidificação resultaram em: ?_2=27 ?V_L?^(-1,1) para a liga 5052 com 2,4%Mg e ?_2=15 ?V_L?^(-1,1) para as ligas com 2,6%Mg e 3,2%Mg. Maiores teores de Mg na liga AA5052 proporcionaram uma expressiva redução no valor de ?2 para uma determinada VL. A evolução da dureza mostrou-se diretamente relacionada ao tamanho e a distribuição dos intermetálicos presentes, sendo ?2 o fator predominante neste controle.

Oct 30, 2017