Search Documents

By Jacob L. Mathis, Todd Tharpe, Jonathan Steflik, R. M. True

In June 2022, Louisville MSD completed a 6.5 km (4-mile), 6.1 m (20-foot) finisheddiameter CSO conveyance and storage tunnel system located along the Ohio River in downtown Louisville, Kentucky. During construction, the Ohio River Tunnel alignment was expanded 2.4 km (1.5 miles) into areas where natural gas was detected. Without delaying construction, the project team developed and implemented a natural gas risk mitigation strategy to safely excavate the tunnel via TBM and install concrete lining. The risk mitigation strategy included the installation of gas-vent borings, increased tunnel ventilation, retrofitting tunneling equipment for “gassy” operations, and modifying the project specific HASP.

Jun 13, 2023

By F. A. Edwards

The Macassa Division of Lac Minerals Ltd. is a high grade gold mine that has been operating in Kirkland Lake, Ontario for the past 51 years. It produces approximately 120,000 tonnes of ore per year, averaging approximately 18.7 grams per tonne (0.45 ounces per ton) of gold. Over the years, the ore body has been developed to a point where mining takes place below the 1,220 m (4,000 feet) elevation and 1,830 m elevation (6,000 feet) west of the original shaft. The mine is currently serviced by two surface and two winze shafts. (Figure 1). The ore body extends below the 1,930 m (6,400 feet) Level which is the bottom of the existing mining operation. An ambitious underground exploration program has substantially increased these reserves. Concurrent with the discovery of greater reserves, has been rapidly escalating mining costs, particularly labour which constituted 66% of the total cost in 1981. These costs continued to escalate as the major proportion of mining was carried out to the west, far away from the existing hoisting systems. This required a three lift hoisting system for men, materials and ore. In addition to the increased travel time and ore handling expense, increased humidity, temperature, ventilation and compressed air losses have added to the inefficiency of the operation. As a result, studies were initiated in 1980 to assess the future of the Macassa operation. The results of the studies indicated that a new deep shaft with a potential to hoist from 2,135 m (7,000 feet) or below was the most attractive option. Detailed design of the shaft and associated surface plant commenced in January, 1982 and the following milestone dates were achieved: 1980 - initial study of hoisting and haulage facilities; January, 1981 - ore reserves in excess of 1 million tonnes of ore at 18.7 g/tonne (0.45 oz/ton) confirmed; March, 1982 - preliminary study of Macassa No. 3 Shaft completed; April, 1982 - permanent hoisting plant purchased; June, 1982 - site clearing commenced; September, 1982 - shaft collared; May 1, 1983 - shaft sinking commenced; February 11, 1985 - shaft reached 1,600 m (1mile); December 1, 1985 - shaft scheduled for completion.

Jan 1, 1985

By John Murray, Daniel Ebin, Robert Gould, Yiming Sun, Lizan Gilbert

The Atlanta Plane Train Tunnel West Extension is being constructed at Hartsfield-Jackson Atlanta International Airport using the Sequential Excavation Method (SEM). The tunnel has shallow ground cover and mixed-face conditions and passes underneath the SkyTrain and MARTA stations and airport terminal buildings. It includes a twin tube Bifurcation with a span of over 45 feet and ground cover of 12 feet. A flat roof is being constructed at the Bifurcation to maximize rock cover and minimize surface settlements. This paper focuses on design and construction challenges for the Bifurcation and tunneling beneath the world’s busiest airport, while minimizing impacts to operations.

Dec 1, 2022

By J. D. Morgan

Introduction In 1987, the US economy continued to grow steadily, reaching an annual rate of $4.6 trillion in the last quarter. The value of domestically processed mineralbased materials rose slightly to $250 billion. The value of US metals rose sharply to more than $7 billion. Industrial minerals rose slightly to $18 billion recycled scrap was valued at $4 billion. Metal prices rose sharply toward year-end. A number of mining and metal companies experienced increased profitability, fostering more optimism about the future. Consumer demand strongly affects mining because the US economy is relatively saturated with long-lived products. Consumer, mortgage, and federal debt continue to rise. 244 million citizens already possess 170 million licensed motor vehicles and 100 million dwelling units. New car production fell 9% to 7.1 million units, but truck and bus production rose 9% to 3.8 million units. New housing starts fell 10% to 1.6 million units. Excess productive capacity exists not only in the US, but also in many other countries. Consequently, the US mineral industry is encountering stiff competition from others, as well as increasing competition from newer engi¬neered materials. Domestic production of plastics rose 9% to 25 Mt (27 million st) - on a volume basis, double all metals. Some 7% of petroleum goes to make petrochemicals including plastics. Imports of nonfuel mineral-based materials in 1987 were valued at $37 billion and exports at $24 billion. Imports supplied a significant proportion of total US consumption of several important mineral materials, including many classified as strategic and critical. In December, the Congress mandated that any major changes in stockpile goals be made only by law, and that the Department of Defense submit annually detailed stockpile supply/demand analyses. Concern about apartheid in South Africa continued, resulting in increasing interest about chromium, manganese, platinum-group metals, cobalt, vanadium, and gold. The National Critical Materials Council continued to monitor the US materials position. The Defense Production Act, authorizing priorities and allocations, supply expansions, voluntary agreements, and the National Defense Executive Reserve continues in effect through Sept. 30, 1989. Under the DPA, the US Bureau of Mines maintains the Emergency Minerals Administration. Further consultations were held with Canada to strengthen the North American defense industrial base. Coal production, 60% from open pits, rose 2% to 825 Mt (910 million st) valued at $21 billion. Nearly four-fifths was burned to generate 56% of US electricity. Exports included 42 Mt (51 million st) of metallurgical coal and 24 Mt (27 million st) of steam coal, with a total value of $3.3 billion. Domestic petroleum production fell 5% to 480 Mm' (3 billion bbl). Uranium mining, including recovery from phosphates, fell 4% to 5.9 kt (6500 st). Nonfuel minerals Major metals: Raw steel production - a major consumer of many minerals - rose 7% to 79 Mt (87 million st). Domestic iron ore production rose 11% to 44 Mt (48 million st), about 96% pelletized. Net imports, though, fell 8% to 11 Mt (10 million st). Raw steelmaking capacity fell 6% to 102 Mt (112 mil-

Jan 5, 1988

By Michelle Mangione, John Kuyt, Zili Li, Michael Mooney

"Twin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world.A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a better understanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This article discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link project overview. The Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with more than 7 km (4 miles) of twin-bore road tunnels, two lanes each, with several caverns, interchanges and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a public-private partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5-m (41-ft) double-shield Herrenknecht tunnel boring machines (TBM) (Harding & Francis, 2013). The TBMs were used in earth pressure balance- (EPB) type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1-m (39.8-ft) diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in nine segments + one key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis (Harding & Francis, 2013). Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Mar 1, 2017

By F. Dingwu

The latest technology and novel equipments in kaolin processing industry in China are described in this paper. Some typical experimental results are presented, which include laboratory-, pilot-or commercial-scale tests. The characteristics of kaolin processing technology are summarized, and the developing trends are indicated.

Jan 1, 1995

By VIVEK KASHYAP, EVODY TSHIJIK KARUMB, PATRICK TAYLOR

Zinc ferrite is considered an integral phase of zinc residues as their presence can render the processing of zinc and critical metals difficult. It is a refractory phase, formed at high temperature in the presence of zinc (Zn) and iron (Fe) during oxidative roasting in zinc processing plants. Because it is refractory to efficient leaching, unreacted zinc ferrite gets concentrated in the final zinc residue, making it a viable source of zinc and indium extraction. The refractory nature of zinc ferrite makes the extraction of associated critical metals difficult. In order to explore a potential economic and carbon-neutral zinc ferrite processing technique, our previous study proposed the partial reduction of zinc ferrite followed by sulfuric acid leaching of the roasting product [1-3]. As demonstrated in our previous studies, partial reduction of zinc ferrite results in a mixture of ZnO, Fe3O4 and FeO, which can be further subjected to leaching for efficient extraction of zinc and critical metals such as gallium and indium.

Dec 1, 2022

By L. Xiao

Using K-oleate as a collector and alizarin red S (ARS) as a modifying agent, selective depression of dolomite from francolite was achieved in alkaline medium (pH> 9.0). Interestingly. ARS was also found to depress igneous apatite in alkaline medium in oleate flotation of apatite and calcite. Adsorption of ARS alone on dolomite was found to be higher than that on francolite. Complimentary adsorption experiments of ARS and K-oleate showed that oleate adsorption was increased in the presence of ARS on francolite but not on dolomite. K-oleate adsorbs on both francolite and dolomite and causes precipitation of calcium and magnesium oleate. Such precipitates can be pre-vented when ARS is present. The results are explained in terms of competitive adsorption for the active sites on francolite and dolomite by oleate and ARS, and their interactions with dis-solved mineral species in solution.

Jan 1, 1988

By Mohammad Irshad, Larry H. Heflin

INTRODUCTION The planned 166 kilometer (103 mile) Metro rapid rail transit system in Washington, D.C. is being designed and constructed by the Washington Metropolitan Area Transit Authority. At the present time, 112.6 kilometers (70 miles) of this system is in operation and contains 21 route-kilometers (13 miles) of rock tunneling, and 14.5 route-kilometers (9 miles) of soft ground tunneling. An additional 2.4 kilometers (1.5 miles) of single track tunnels in rock are planned and 6 additional contracts will consist of some 8 kilometers (5 miles) of twin tunnel, resulting in 16 additional linear kilometers (10 miles) of single track tunnel in soft ground. The Authority plans, upon its evaluation and the recommendation of the General Engineering Consultant, to include an alternative design incorporating the convergence confinement method of construction known as the New Austrian Tunneling Method (NATM), for Sections E-5, E-6e and E-8a of the E-Route. The Metro system is constructed in a variety of geological conditions and crosses the boundary of two major geographic provinces. Rock tunneling is to the west of this "fall-line" boundary, soft ground tunneling to the east. The soft ground tunneling portions of Metro construction lie in the coastal plain which consist of a

Jan 1, 1987

By D. W. Park

Longwall Strata Control and Maintenance System (LoSCoMS) is a software and data communication system developed at the University of Alabama. This system integrates real-time shield monitoring, data presentation, analysis and forecasting of forthcoming events. The main objective of this system is to provide stability information on longwall panels including excessive shield load, low setting pressure, leg leakage and poor shield performance, eminent maintenance problems, etc. Analyses of various mining and geological parameters were also performed to determine past and present roof characteristics and to forecast roof loading patterns for the following mining cycles, next periodic weighting, etc. A local coal mine in the Warrior Coal Basin has adopted this system to provide daily evaluation of ground stability and maintenance problems of their longwall panels. Two years of experience with this system is covered in this paper.

Jan 1, 1998

By G. T. Lineberry

A systematic, comprehensive, balanced approach is presented for underground coal mine design, capable of being standardized and generalized. This approach epitomizes professionalism and must preceed the physical product. Design involves a varied senior staff and requires extensive selective input data. Engineering follows a total systems approach, operating in and for a constricting geologic setting, heavily constrained for safety, health, and environmental protection. It must also anticipate execution and operation. Engineering prominence and momentum are maintained, with sub-optimizations balanced by judgments--the "art and science" of engineering. The flow-chart starts with organized input data: Company Capabilities, Property Description, Geologic Analysis and Reserve Analysis. Engineering combines Ground Control with Excavating and Bulk Handling to map feasible Mining Methods, the crucial Milestone Diagram. Layout and Sequencing follow, with numerous alternatives examined. Scheduling is performed on the best designs, using predicted advance (performance) rates. Active and mined-out areas are isolated into time-related parcels, or increments, for the mine life. Bulk Handling, Life Support (especially ventilation and drainage), and Normal Support systems occupy each parcel. Regulations are then checked. Management concerns are covered, and an Economic Analysis is performed for profitability. This and the design represent an Initial Tentative Solution. Continued iterations produce multiple and improved choices.

Jan 1, 1987

By H. Huang, R. N. Gow

"In Part I, Gibbs’ phase rule was applied to mass-balanced EH-pH diagrams for the Cu-As-S-H2O system. The diagrams were generated using the stoichiometry of enargite as a basis. In this study, the calculations were expanded to cover the stoichiometries of three other Cu-As-S minerals – tennantite, sinnerite and lautite – and compared with enargite. Stability regions within the resulting EH-pH diagrams were found to change with stoichiometry such that a particular mineral would predominate if its stoichiometry was used in the calculation. Solution speciation was also found to vary, with thioarsenate being the best example. This stoichiometric effect helps to explain results reported in the literature and would be difficult to realize if it were not for mass-balanced calculations. IntroductionA comprehensive thermodynamic review has been conducted on the aqueous copper-arsenic-sulfur (Cu- As-S) system (Gow et al., 2014, 2015a, 2016b; Gow, Huang and Young, 2016c). Data on the free energies of more than 100 species were collected from various authors, and thermodynamic databases collated to produce mass-balanced EH-pH diagrams using the thermodynamic equilibrium calculation software STABCAL (Huang, 2014). The full database is listed and discussed in Gow et al. (2015a). Diagrams were generated for enargite and confirmed with Raman spectroscopy using bulk mineral electrodes in order to identify reactions spectroelectrochemically. Theoretical calculations agreed well with the experimental results under alkaline conditions (Gow et al., 2015a), acid conditions (Gow et al., 2014) and alkaline sulfide leaching conditions (Gow et al., 2015b).In the present study, additional mass-balanced EH-pH diagrams were generated by changing the Cu-As-S stoichiometry from enargite (Cu3AsS4) to tennantite (Cu12As4S13), sinnerite (Cu6As4S9) and lautite (CuAsS). Regions for the thermodynamically stable species were shown to change with the four different mineral compositions. Potential leach conditions, both for co-dissolution and selective dissolution techniques, were examined for differences in predominant species according to changing copper-to-arsenic ratios, sulfur compositions and sulfur oxidation states."

Jan 1, 2016

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

A numerical investigation of the effect of pore pressure regime on the safety factor and the critical failure mechanism is presented for fly ash storage facility. Pore pressures’ measurements from standpipe piezometers and pore pressure estimated from seepage analysis are used to compare the factor of safety for a fly ash slope. This was applied for considering static and seismic scenarios. A probabilistic approach was applied to account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation. Slope stability analysis is conducted in two and three dimensions, adopting the limit equilibrium analysis approach, and also a finite element seepage analysis, to assess the stability of the slope. The two-dimensional cross-sections were extruded to three-dimensional models to estimate the factor of safety and associated shear failure. The results from the performed analysis suggest an increase in safety factor values of 5%.

Mar 27, 2024

By Steve Kral

In recent years, junior mining companies, mostly listed in Canada, have taken a beating in the finance markets. Simply put, potential investors have been leery of sinking millions into exploration and mining projects due to volatile commodities prices and an uncertain regulatory climate in developed and developing countries. The 2014 edition of the Prospectors and Developers Association of Canada (PDAC), however, seemed to be a bit different for some juniors. Equity valuations have improved and metals prices appear to be stabilizing. So, for some of the stronger junior companies, there is some hope. Merger and acquisition (M&A) activity is picking up and, believe it or not, companies are raising some capital. Billed as the largest annual mining meeting in North America, the PDAC conference attracted more than 25,000 mining and exploration professionals from around the world. Organizers were anticipating attendance to break the 30,000 mark. But, given the state of the exploration end of the mining business, 25,000 is still a respectable number. Junior companies that are in the project feasibility stage, or have made promising discoveries that stand a good chance of proceeding to production, are being looked at by potential investors. Those are the survivors of the last three years of dismal M&A activity. On the other side are the juniors that are still around ? and there are plenty of juniors that were at the PDAC last year but have since disappeared ? but have little or no working capital. One analyst calculated that there are about 850 companies with less than $200,000 in working capital and about 600 with negative working capital. This will likely result in fewer junior mining and exploration companies as the year progresses but the ones that remain should be stronger.

By R. E. Hucko

The principal thrust of the U.S. Department of Energy (DOE) Coal Preparation R&D Program is to develop technology to reduce the ash and sulfur contents of United States coals to levels such that the resultant product can be formulated into a high quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. Specifically, the objective is to develop and refine cost-effective physical and chemical beneficiation processes to extract 85-95 percent of the total sulfur and ash. The Coal Preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in-house and by a cross section of industrial organizations, universities, and national laboratories. Research is subdivided into three areas -coal characterization, beneficiation, and ancillary unit operations. This paper will provide a brief overview of many of the research projects being carried out in these areas in fiscal year 1984.

Jan 1, 1984

By Kevin Saeler, Patrick Willaman

Utilizing automation is one way to improve competitiveness. Roof and rib bolting in underground coal mines has not changed significantly for more than 40 years. Most roof bolting is still a largely manual process involving high levels of staff carrying out repetitive work. Roof bolting statistically has one of the highest levels of underground accidents, including finger, hand, and arm injuries. Operators are exposed to falling objects and becoming entangled in roof bolting apparatus while roughly moving awkward 6-ft drill steels and roof bolts. It is estimated that over 25 million roof bolts are installed annually in the U.S. underground coal market with well over 1,500 operators involved in roof bolting on a day-to-day basis. Recently electrohydraulic roof bolting rigs have been installed to offer partial automation of the drilling cycle and the bolting cycle. The next stage is to provide a storage and loading system to allow full automation of fullcolumn resin roof bolts. This paper reviews the latest electrohydraulic roof bolting equipment and discusses the testing of a fully automated drill rig. Full electronic control allows each step of the roof bolting process to be recorded, providing a digital record of each installation, including hole depth, spin time, gel time, torque, and cycle time. Other benefits include monitoring of water pressure and flow, used to prevent blocked drill steels as well as digital fault finding. A fully automated roof bolting machine greatly improves operator safety and gives high-quality repeatable roof bolting with reduced cycle times.

Jul 1, 2023

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the Separation Efficiency: ES = (R ? Rg) where R is the percentage of the valuable constituent and Rg the percentage of the waste appearing in the concentrate. The Separation Efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products.

Jan 1, 1969

By W. J. Martin

At the termination of mining, the quality of ground water in the ore-zone aquifer must be returned to a condition predetermined by the permitting agency. To immobilize the redox-sensitive elements (e.g., uranium, arsenic, selenium, molybdenum), it has been suggested that a reducing agent be circulated through the leached ore zone. We have conducted laboratory experiments to test the ability of sodium sulfide as such a reducing agent. Sodium sulfide lowered the redox potential of the effluent such that insoluble minerals containing the redox-sensitive elements should be stable. The uranium concentration of the solution decreased by more than three orders of magnitude. In column experiments, by the time ten pore volumes of the sulfide solution had flowed through, sulfide minerals were forming. The experimental results indicate that the addition of sodium sulfide should cause the chemical reduction of the leached sediments, thereby producing long-term stability of the ground-water/sediment system.

Jan 1, 1986

By Oliver Gutsche

High-pressure roll mill comminution of heterogeneous multicomponent feeds was simulated with artificial limestone-quartzite mixtures using a piston-die press. The influence of heterogeneous interactions between components of the mixture on grinding path, energy utilization and energy split have been examined. Primary fractures are governed by differential fracture strength and attrition resistance of the components at heterogeneous contacts; subsequent secondary and tertiary fracture events are governed by coarse-fine interactions in the particle-bed. The weaker component is preferentially ground out of the feed size fraction and concentrates in the fines. Energy split among the components in the mixture is a function of their relative fracture strengths. It doubles for limestone and decreases by a factor of 5 for quartzite over the entire range of the mixing ratio.

Jan 1, 1995

By G. T. Adel, P. E. Richardson, R. Pazhianur

Cathodic protection using impressed current was employed to reduce mill wall wear during ball milling. Wear rates were determined from weight-loss measurements made on four 1-in.-diam mild steel coupons that were installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH levels of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 30% to 60%. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It was also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1998