Search Documents

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Ti and Zn-1.0 wt pct Cu-Ti alloys containing up to 0.36 wt pct Ti. Finish rolling was at varied temperatures to total reductions as high as 92 pct. Alloy properties are very sensitive to various combinations of composition, rolling temperature, and reduction. Properly rolled Zn-1.0 Cu-Ti alloys are superior in strength to Zn-Ti alloys. Conditions are described that lead to best tensile properties. Creep resistance for Zn-Ti alloys decreases with increased rolling temperature when finish rolled to 92-pct total reduction: but not when finish rolled to 33- or 67-pct reduction. Creep resistance for 7n-1.0 Cu-Ti alloys improves with increased rolling temperature to about 480° F. Heavily cold-rolled Zn-1.0 Cu-Ti alloys have fine grain sizes and poor hardness, tensile, and creep properties, but high ductility. Thermal expansivity is markedly affected by the copper addition. Data show the anisotropy of tensile, creep, and thermal expansivity properties. Large idiomorphic crystallites of TiZn15 appear in both Zn-Ti and Zn-Cu-Ti alloys when more than about 0.2 pct Ti is present. A new Zn-Cu-Ti intermediate phase was also identified. Empirical equations are presented relating creep rates with major process variables.

Jan 1, 1971

By J. D. Dixon

The Bureau of Mines investigated the principles of support-rock interaction, based on structural matrix methods which permit mathematical formulation of the problem and computer solution. The principles are given under two main sections: the first discusses the idealization of the tunnel support structural system for matrix analysis; the latter discusses the analysis procedures necessary for carrying out the solution. A general frame matrix computer program and a medium-size computer should be sufficient for carrying out the procedures involved. The example problem consists of a circular tunnel support which is subjected to a uniformly distributed vertical load, Three wall thickness-radius ratios are studied in combination with four support-rock modulus ratios. This problem illustrates the main procedures of the support-rock interaction analysis involved, and examination of the results reveals the influence of the relative rigidities of the support and the rock.

Jan 1, 1971

Mainland China To Pay Japanese Company On Contract Claim. - Mitsubishi will receive $39 million from Red China, half of what was asked, for China's having, curtailed work on a 5369 million steel rolling mill at Baoshan near Shanghai. Copper Found in Chile. - Utah International Inc., in conjunction with Getty Oil Co., has discovered a cooper deposit in northern Chile. Early drilling reveals an enriched zone grading 1.2% to 2 3% copper. Chile already has tie world's largest Cu reserve base. Soviets To Aid Laotian Tin Industry. - The U.S.S.R. has agreed to help strengthen the tin industry in Laos, a client state. In the past, Laos has only produced small amounts of tin concentrate, 500 tons to 1,000 tons per year presumably shipped to smelters in Singapore or Penang, Malaysia. Under the agreement made in June, the Soviets are to supply equipment to increase the out put of tin from the Phontieu, Neng, and Nongsen mines and help Laos with the construction of a tin smelter. The U.S.S.R. itself is a net importer of tin, although a substantial producer of the metal.

Jan 1, 1981

By J. S. Dunning

A primary goal of the Federal Bureau of Mines is to minimize the requirements for scarce mineral commodities through conservation and substitution of more abundant elements, such as iron and molybdenum. One example of this is the research effort to devise substitute materials for specialty alloys, thereby conserving nickel and chromium in high-volume stainless steels. As a possible substitute for the solid solution strengthening of chromium and nickel, the precipitation hardening characteristics of a number of binary iron-based systems in which Laves phase precipitates, such as Fe2Mo, are formed were investigated. Several hardening responses were observed, but none were ideal. The Fe-Ta binary system had the highest magnitude of hardening, even with low alloy additions, and the Fe-Mo system had unique stability at temperature. Accordingly, the Fe-Mo-Ta system was selected for study to determine if a ternary Laves phase could combine high hardening with long-term stability at elevated temperature. Hardening and stability were reflected in excellent elevated temperature, tensile, and stress rupture strengths. Future research will study ternary systems based on more abundant resource materials, such as the Fe-Mo-Ti system, together with additions, such as aluminum and minimal chromium, to provide oxidation resistance.

Jan 1, 1979

By J. P. Coughlin

Gypsum plaster is calcium sulfate hemihydrate (CaS04-1/2H2O). There are two varieties, commonly designated as a and ß. The hydration setting) of this plaster involves the chemical reaction: CaS04?1/2H20(c) + 3/2H20(l) = CaSO4?2H20(c); that is, the hemihydrate combines with water to form the dihydrate. Many substances, when present as impurities, either in the hemihydrate or the water have influenced the rate of the hydration reaction. The objective of the Bureau of Mines work described in this report was to investigate the accelerating or retarding effects of small amounts of dissolved substances and to attempt to classify these effects upon a chemical basis. To eliminate competing effects, the work was conducted separately on the two varieties of hemihydrate; both were in highly pure form. (Commercial plasters usually are a mixture of the hemihydrates, with other substances present as impurities.) As the hydration reaction of each variety of hemihydrate evolves heat in amounts known from previous work, 5,6/ the authors decided to use calorimetric methods to follow the extent of the hydration reaction as a function of time. Two calorimetric methods were employed. One was designed to study the hydration reaction with a large water to plaster ratio and the other with a small water to plaster ratio (to simulate commercial practice in utilizing plaster).

Jan 1, 1959

By C. H. Elder

Coal degasification boreholes drilled from the surface have been success-fully hydraulically stimulated to increase the flow of gas from the coal. This Bureau of Mines report describes the hydraulic stimulation procedure for a coalbed, the equipment required, and design criteria for the treatment. Three examples of stimulation treatment show from fivefold to twentyfold increases in gas production. The tests were conducted in the Pocahontas No. 3 coalbed, Buchanan County, Va., the Pittsburgh coalbed, Washington County, Pa., and the Mary Lee coalbed, Jefferson County, Ala. Two sites where the coal was hydraulically stimulated and exposed by subsequent mining show no adverse effect on mining operations through the treated zones. The induced vertical partings were confined to the coalbed and did not in any way affect either roof or floor rock.

Jan 1, 1975

By E. P. Youngman

Except possibly by individual natives and Liberians (small specters), is now being carried on in Liberia, according to a late report. definite information is obtainable with respect to the mineral resources of e country, except that iron ores are said to be abundant. Tin, copper, zinc, site, corundum, lead, bitumen or li nite, and diamonds have all been re- parte, but no commercial Geposits are known to have, been found. Gold has been duce, but not in significant amounts, as may be inferred from the customs - rt for Liberia recording the exportation of gold to the value of $4.80 Germany from the port of Cape Mount in 1925. It is not uncommon for atives to come into towns with African gold and valuable minerals, but they e reluctant to sive information concerning then. Some years ago the Liberian Government was seeing a loan in return for oil concessions, but apparently no drilling bea boon don

Jun 1, 1932

By R. L. Hopkins, H. T. Rall

A continuous method has been developed for preparing thiolacetic acid . Acetic anhydride and hydrogen sulfide are passed concurrently over an amine ion- exchange resin , under 20 - psi pressure . The thiolacetic acid , a product of the reaction , is flashed continuously from the crude reaction mixture and is purified by fractional distillation . The yield of thiolacetic acid is in excess of 80 percent based on the acetic anhydride charged . INTRODUCTION In the synthesis of reference compounds needed in the identification of sulfur compounds in petroleum , thiolacetic acid has become an important reagent because of its use in the synthesis of thiols by addition to appropriate olefins : R - CH = CH₂ + CH3 - COSH R- CH2 - CH2 - S - COCH R - CH2 - CH₂ - SH + CH3COONa NaOH (1 ) The commonly used procedures for its preparation , as described by Clark and Hartman (1 )4 and by Ellingboe (2 ) , are based on the batchwise reaction of acetic anhydride with hydrogen sulfide :

Jan 1, 1964

By Michael D. Fenton

Detailed comprehensive assessment of the performance of Afghanistan's mineral industry during 1987 is virtually impossible, owing to the paucity of reliable published information. It was evident, however, that the level of civil disorder, now in its eighth year since the arrival of significant numbers of Soviet troops, was in actuality little removed from open civil war. Insurgents controlled substantial areas of the country and imperiled any industrial activity in many places. Assistance programs by the U.S.S.R. and other Eastern European nations were directed at developing the country's meager mineral industry, but the economy was generally viewed as chaotic. The inflation rate was somewhere between 20% and 30%; major food shortages contributed to the discontent of the population, and numerous villages were devastated by Soviet and Afghan Government campaigns to destroy the insurgents and cut their supply routes. Moreover, proposals by the Soviets and the Kabul Government aimed at reducing tensions with the rebels and scaling down the warfare seemingly were taken by the opposition as signs of weakening by the Soviet-backed Government, and rather than reducing aggressions, seemed to heighten insurrectionist activities. Efforts to entice the substantial number of Afghans who have fled to nearby areas of Pakistan and Iran to return to their country seemingly were failures, and indications near yearend that the Soviet Union might soon begin withdrawal of its occupation force of nearly 120,000 did little if any to reduce disorder.

Jan 1, 1989

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects world-wide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

Exposure to airborne respirable crystalline silica dust can lead to silicosis, a debilitating lung disease. On surface coal mining and construction sites, blast hole drills are notorious sources of airborne respirable dust that may contain significant amounts of silica. The drill operator and drill helper usually receive the greatest silica exposure compared with other occupations. As a result, many drilling operations have been, and still are, on more stringent dust standards. Drilling through various rock formations naturally presents a strong potential for silica dust generation for several reasons. First, drilling is a pulverizing process that generates large amounts of very small dust particles. Second, the bailing air used to flush cuttings from the hole leaves the hole at a very high velocity and can be difficult to contain. Third, many fixed shrouds used to enclose the area beneath the drill deck have a significant amount of leakage due to 1) gaps between the shroud and ground created by raising/leveling the drill, 2) gaps in the corner seams, and 3) tom deck shrouds. CONTROLS A dry dust collection system is typically connected to the drill deck to collect dust as the bailing airflow transports the cuttings (and significant amounts of airborne respirable dust) out of the drill hole. Deck shrouds are installed in an attempt to enclose the volume around the drill steel and prevent dust escaping. However, most deck shrouds are rectangular and constructed of four separate pieces of rubber belting attached to the deck. Because of this design, there is usually a significant amount of dust escaping from the open seams as well as the open area between the shroud and the ground. This dust can be a significant source of silica exposure to drill operators as well as other personnel downwind of the drill.

By d&apos, Kathleen J. Amico

THIS SUAMMARY is shown in Minerals Yearbook volumes I and III of this series on mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, and on the principal minerals imported into and ex- ported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1962

By Ronald F. Balazik

The introduction of "high-tech" materials such as new polymer composites presents significant competitive challenges and opportunities in conventional mineral markets. Moreover, rapid advances in materials science are critical to the resolution of important economic and strategic issues, including national competitiveness and import dependence. This Bureau of Mines study examines the displacement of conventional nonfuel mineral materials by certain new materials, specifically advanced plastics and ceramics. Analyses of substitution by plastics are conducted for five major U.S. industrial sectors: motor vehicle manufacturing, aerospace applications, building and construction, packaging, and heavy machinery production. Based on interviews with more than 60 scientists, executives, and other professionals engaged in materials development and sales, forecasts of substitution by plastics during the 1990's are made for aluminum, steel, and glass. In addition to these forecasts, study findings identify key factors that will influence the emergence of advanced materials in the next decade.

Jan 1, 1987

The Technology Transfer Seminar on Mine Communications held on March 21-22, 1973, at the Pittsburgh Mining and Safety Research Center, Bruceton, Pa., presented information about recently developed equipment, instruments, and techniques for use in mine communications systems. All of the basic ideas presented in the fine seminar are operational in the Bureau of Mines Safety Research Mine in Bruceton.

Jan 1, 1974

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This article focuses on U.S. Bureau of Mines (USBM) and National Institute for Occupational Safety and Health (NIOSH) research to examine factors that had a significant influence on mine face ventilation design during the past century. Several "milestone" events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative face ventilation designs and a consistent commitment to mining health and safety. Ventilation has always been a concern in underground coal mining. For many yeas, there was no appreciation of how ventilation could be used to remove harmful contaminants from the air or how to control airflow quantities. The first known problems with ventilation date back to the 14th century, when it was recognized that lack of air was a major impediment to the expansion of mines. The common method of solving ventilation problems at that time was to abandon the existing mine and start a new one nearby. Ventilation in the early days of coal mining was accomplished by means of a natural draft, created principally by a difference in the weights of columns of air between the intake and return openings. Later, in the 18th and 19th centuries, a furnace was introduced underground to increase the updraft in the return shaft. This allowed for a larger quantity of air in circulation. When mines went deeper and became larger, mechanical ventilation became necessary and was first accomplished by steam-driven fans. These fans became more prevalent as furnaces were prohibited in underground mines, especially after the Avondale disaster in Pennsylvania in 1869 (Roy, 1876). Eventually, these fans were replaced by more powerful, electrically [ ]

By D. R. Tesarik, F. M. Jones, J. B. Seymour, L. A. Martin, T. J. Williams

Determining backfill stress is an important part of evaluating mine safety, whether personnel are working in proximity to backfill or in other areas of the mine where backfill is an integral part of regional support. To assist in determining stress in backfill more accurately, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Placer Dome, Inc. (Turquoise Ridge Mine), Peabody Energy Co. (Foidel Creek Mine), and Hecla Mining Co. (Lucky Friday Mine) used temperature readings recorded by thermistors to correct for the influence of temperature on stress data. These thermistors were positioned in the stems of earth pressure cells installed in backfill. Corrections were then calculated and compared using four different methods: polynomial equations fit to temperature-versus-stress plots before the pressure cells were loaded by overburden, a factor provided by the manufacturer, a theoretically derived factor, and a linear correction factor based on information collected during periods when no mining was taking place. To evaluate the accuracy of these methods, corrected stresses were calculated using each method and results compared to cumulative stresses caused by blasting at one of the mines. Results indicated that only a small percentage of the temperature effect on stress was corrected using the factor from the manufacturer because that factor accounted for only the pressure transducer and not the entire instrument body. Stresses adjusted with a linear correction factor based on information collected during periods when no mining was taking place were the most accurate. Stresses recorded at two other mines were corrected using the theoretical method and the polynomial equations method; the two methods produced similar results. For some time intervals, the results were identical.

Jan 4, 2006

By C. D. Litton

The results of full-scale fire tests are used to determine optimum distributions of fire sensors for the protection of conveyor belt haulageways in underground coal mines. Empirical relationships are derived that relate the spacing of fire sensors to the rate of development of the fire hazard. For this application, a critical fire size is defined as that size of fire for which belt ignition and subsequent flame spread down the belt is assured. Detection and alarm, regardless of sensor type or sensing methodology, must be achieved at some point in time before the critical fire size is reached. Based upon this approach, it is found that the horizontal spacing for products-of-combustion sensors is in the range of 300 to 600 meters, while the required thermal sensor spacing is found to be ~4 meters or less. Additional design criteria are discussed for product-of-combustion fire sensing systems.

Jan 1, 1982

By Bill M. Stewart, Phil W. Patton, Curtis C. Clark

Back injuries from handling materials in underground mines continue to be a major safety problem. In spite of the ingenuity of many people and the development of numerous mechanized aids, the number of materials-handling injuries remains second only to the number of roof fall injuries in underground coalmines. Relocation and repositioning of electrical cable, conveyor belt parts, and roof bolt sup-plies in particular are the sources of significant numbers of back injuries. To help reduce such injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are examining Mine Safety and Health Administration accident data to determine correlations between materials-handling tasks and the number of back injuries. Also being investigated are new technologies used in underground mines in the United States. Equipment is being developed or modified that would replace the necessity of doing lifting tasks manually. A Coleman manipulator was tested, and modifications were made to make it more suitable for underground mine use. To reduce or eliminate the need to manually clean off materials that commonly plug grizzly openings, a track-guided pincher arm device was developed. Oversized rock can be broken with the pincher arms in the up position, and the arms can be lowered to grab and remove debris. The arm can also be used in a sweeping action to remove cohesive fines that may bridge grizzly openings.

By D. R. Flinn

The Bureau of Mines has studied the electrochemical parameters important to the preparation of coatings of the platinum-group metals. Using molten mixtures of sodium and potassium cyanides in an inert atmosphere, techniques have been developed that permit the preparation of baths for platinum, rhodium, and iridium electrodeposition. Cyclic voltammetric and slow sweep rate linear polarization techniques have been utilized to determine optimum potential and current values for preparation of plating baths and for the electrodeposition of coatings. Techniques are described for the deposition of platinum and rhodium coatings at near 100 percent anode and cathode current efficiencies, and for iridium at approximately 80-percent efficiency. Palladium deposition from these molten cyanide baths remains un-satisfactory. The chemistry of the palladium-containing cyanide bath is discussed. Examples of scanning electron microscope photomicrographs of typical platinum coatings are presented. Techniques are described for the preparation of platinum coatings on large objects.

Jan 1, 1982

By Ralph L. Rinehart, Wils L. Cooley

This paper summarizes recent experiments with grounding systems. Problems and potential hazards related to in-mine grounding systems are discussed. The monitoring of trailing cable ground conductors and testing of commercially available ground monitors are discussed.

Jan 1, 1975