Search Documents

By S. K. Singh, P. R. Sheorey

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

By Bernard J. Steblay

Millions of mechanical anchor roof bolts are used each year for mine structural support. The benefit of this bolting depends on a number of factors including rock density, bolt length, in situ stresses, time elapsed between mining and installation, rock properties, bolt patterns, and tension (Lang, et al., 1979). Installation tension is a major determinant of support quality. Postinstallation tensions indicate both the usefulness of the individual bolts and the behavior of the reinforced rock structure. The importance of short- and long-term bolt tension measurements is well recognized, and such measurements are required by regulations (Fed. M/NM Nine Safety and Health Reg.). These regulations also take into account the difficulty of practical tension measurements. Only a statistical sample of the bolts installed is required to be measured using current torque wrench technology. Drawbacks to this practice are that the anchorage is disturbed and perhaps weakened, accuracy is limited by friction to about 30% (Lang, et al, 1979, and Barry, et al., 1956), and the procedure is relatively time intensive.

Jan 1, 1984

The vast coal resources of North Slope, Alaska can be expected to attract substantial interest because the nearly flat lying coal beds of the coastal plan are specially amenable to surface mining. Mining on a scale large enough to justify coal development in this area could have severe environmental effects. The mitigation would be uncertain because large scale coal mining and reclamation operations have not been carried out in the arctic The deficiency of the scientific data base is another factor that requires consideration if coal mining has to develop in accordance with the objectives of PL 95-87. The objective of this paper is to establish the interrelationship between the problems due to permafrost and factors in reclamation of post mining land in order to find ways to transform nature in a rational and purposeful manner and to suggest specific reclamation approaches that may be appropriate in this region.

Jan 1, 1986

By Krawiec Alfons

The threat of rock bursts along with the danger from methane gas and coal dust explosions belongs to particularly dangerous phenomena in Polish pit-coal mines. This phenomenon results mainly from the physical-mechanical properties of the rock mass as well as the geological-tectonic structure of the Upper Silesian Coal Basin. In the postwar years in Polish coal mining thanks to a multi- directional activity, a decrease of rock bursts and their effects has been noted. For example, the number of rock bursts reported in 1965 amounted to 71 in comparison to only 23 in 1974. The ratio of rock bursts calculated for 100,000 tons of coal extracted from rock bursting strata amounted to 0.08 in 1965; however, in 1974 it amounted to 0.023 /Fig. 1/. These results were obtained in face of a continually growing potential threat from rock bursts caused by the systematic increase of extraction from rock bursting strata, exploitation at gradually greater depths along with the extension of exploitation into deposits enclosed in different types of pillars and other parts of deposits surrounded by workings. Despite the achievements of science and mining practice in this field, this threat has not yet been fully studied and controlled as it should be, As a result, research on preventing rock bursts is being continually widened in Poland. This research has a complex, multi-staged and long-range character. Theory, laboratory and field work in the mines are working on a solution to the problem.

Jan 1, 1976

By C. M. Brinckerhoff

Much has been written in the mining technical magazines about the caving system. Many of these articles were published in the Transactions of the American Institute of Mining Engineers prior to World War II. In recent years little has been written on mining methods or on the detailed planning always required. Block caving had primarily been used to mine deep copper ores in Africa, the United States and in Chile, although other ores had been mined by this same system. Asbestos ore had been caved in Canada, tin ore in Bolivia, molybdenum ore in Colorado, iron ore in Wyoming and Sweden, and limestone in California.

Jan 1, 1984

By Brian Fulcher, Matthew Bartlett, Jarrett E. Carlson

This paper discusses the challenges to complete the construction of two large underground Metro stations and connecting tunnels in the Tren Urbano system. The completion work includes the installation of specialized mechanical and electrical systems, extensive architectural finishing as well as coordination with systemwide power and controls installed by others. A unique feature of this project was the simultaneous design and construction of the structural/civil/architectural/mechanical/electrical works by KKZ separately from the power and control systems under the management of the Owner, its consultants and other contractors. Completion of this project comes after almost six years of continuous design and construction in a dense urban environment. The project was confronted by many challenges that could only be met with the combined efforts of the Joint Venture team in close cooperation with the Owner and its System wide Contractor. This paper will also address many of the major design and construction changes implemented to suit the Owner’s requirements.

Jan 1, 2003

By J. Z. Cheng

The extraction of thorium from industrial radioactive wastewaters discharged from Rare Earth (RE) plants was studied by the liquid membrane emulsion technique using P507- Span80-sulphonating kerosene-HCl. The emulsion conditions, the technological factors such as ratios of oil to the internal aqueous phase and water to emulsion, and the extraction time etc. were investigated.

Jan 1, 2008

By Stephen A. Orr

Underground mining is a dynamic art and science with a diverse set of design, production, and economic criteria that must be considered before selecting an optimal method to extract the ore. While all methods can be technically classified as either self-supported, supported, or caving, the multitude of subsystems and existing variations bear witness to the fact that each orebody is unique and, as such, justifies an individual approach to optimize mineral extraction. In this sense, underground mining is an art. The ability to evaluate the unique characteristics of each ore body and utilize sound engineering principles to design the optimal system constitutes effective method selection. The task by no means ends at this juncture, however. Subsequent implementation requires an ability for modification. Very rarely are all the facts available to make a concrete decision prior to development of the resource. As a result, the risk of a wrong decision can never be eliminated. This requires a significant degree of flexibility with each method. Each unit of exploration, development, or exploitation work contributed to a deposit enhances knowledge of the ore body. The best mining methods are those that correctly account for the known parameters but provide an allowance for change at minimal cost and adapt to unanticipated conditions.

Jan 1, 2008

By E. A. Zawadzki

The problem of pollution of water by mine drainage is at least as old as the mining industry itself. However, research on the formation, composition, treatment, and abatement of mine water is a relatively recent historical event. At Bituminous Coal Research, Inc., acid mine drainage control has been an important area of work since 1944, at which time BCR began sponsorship of research at West Virginia University. The work at West Virginia University involved a detailed study of the acid mine drainage problem and led to the identification of iron oxidizing bacteria as important factors in the formation of acid mine water. The results of this research were summarized in 1954 by Temple and Koehler (1) who concluded that "no practical solution for the problem" of controlling acid mine drainage is yet known.?

Jan 1, 1967

By Harvey W. Parker

The underground industry is challenged by many complex technical and non-technical issues and risks. The most obvious of these are the traditional technical issues that we usually try to address with risk management techniques. However, there are many other non-technical risks that our projects face on a daily basis which we often fail to fully recognize or appreciate. This paper addresses some of the less-technical broad-based risks in order to put them into perspective with the technical risks we face day to day in underground planning, design and construction. The good news is that Risk Management techniques are not always about bad things. For obvious reasons Risk Management is always thought of in terms of the ?downside? of risk (i.e., the identification and mitigation of things that can go wrong). On the contrary, there is an ?upside? of things that might go better than expected. Fortunately, if a deliberate effort is made, the same principles and techniques that our industry uses in Risk Management can be applied toward identifying and quantifying the Opportunities and Benefits that might occur. In this way, the process of conducting risk management programs can not only identify the downside risk but can be used to identify and direct projects to take advantage of the upside of uncertainty (i.e., Opportunities as they arise). This beneficial aspect of risk management programs will be highlighted in this paper together with the importance of the non-technical issues.

Jan 1, 2008

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By D. R. Rathburn

Jan 1, 1962

By John F. M. Sims

Political issues and a glaring infrastructure deficiency have retarded the emergence of a strong mining component to the Alaskan economy in recent years. Barriers to orderly mineral development are slowly being removed attendant upon changing political circumstances. Infrastructure development, as an investment avenue as well as a responsibility of the State, is receiving much greater attention than in the past. Alaska of course has a rich and varied mining history going back to the 19th Century. This paper, however, focuses on the mining potential, not the mining heritage of the 49th State. The mining industry is emerging from a nadir in the economic cycle - times during which it was buffeted by unsympathetic administrations and confused and confounded by the protracted land status- conflicts prior to enactment; of the Alaska National Interest Lands Conservation Act (ANILCA) and other milestone legislation. Today Alaska's mining industry looks toward a bright and healthy future and, in the process, will become a very important and vital component of the State and national economy.

Jan 1, 1982

By Robin P. Gardner

The development and use of short-lived radioactive tracer methods for the on-stream determination of residence time distributions in large-scale ball mills is described. Tests are reported on a pilot-plant ball mill with 0.43 m diameter and 0.86 m length and on an industrial mill with 1.83 m diameter and 2.74 m length. Tests with different tracer feed sizes indicate that the residence time distributions on both mills are independent of charge particle size. Similar tests are planned for a-large ball mill of 4.57 m diameter and 9.30 m length. No safety problems were encountered in these tests and none are anticipated in tests of the larger mill.

Jan 1, 1978

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The forestry reclamation approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22 m (4 ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes (i.e., greater than 23°) could lead to slope failures, which is one of the issues that the Surface Mining Control and Reclamation Act of 1977 (SMCRA) sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. During this first phase of investigation, there has been no major mass movement of the slope and slope stability analysis indicates that the application of the FRA has little impact on the overall stability of the slope. Mining Engineering, 2011, Vol. 63, No. 12, pp. 55-62. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Michael MacMillan

AI is already changing how mining companies are seen, judged, and trusted. This paper discusses “reputation engineering,” a structured way to build trust in a world where AI systems summarize and evaluate everything a company says publicly. Using mining examples, emerging AI search trends, and real communication work, the paper explains why the next 12–18 months are a crucial window for action. It also provides a practical framework to help mining companies improve their visibility, accuracy, and consistency across both human and machine channels.

Feb 22, 2026

By Robert Kimutis, Lihong Zhou, Mark Mazzella, Jim Addis

Due to the surge in shale gas production, a substantial number of unconventional shale gas wells have been drilled across U.S. coal reserves. Gas breaches resulting from damaged wells pose a considerable safety risk to miners. This paper investigates how a ventilation system can effectively manage breached gas through a network-based numerical model and laboratory-scaled physical model. Several hypothetical gas breach scenarios in a longwall area are simulated, exploring factors influencing gas mitigation. The study establishes correlations between breached gas inflow and gas concentration at critical locations. The findings in this study provide valuable insights for managing mine ventilation systems and enhancing coal miner safety.

Feb 1, 2025

By Joel K. Waterland

The Homestake Mining Company at Lead, South Dakota is one of the few remaining gold properties still in operation, in this country. The mine is relatively deep, with a bottom production level of 4250 feet, and a bottom development of 6200 feet. 4, 800 tons of ore are produced daily from three rather large, but inconsistent ore bodies; the dip of which is easterly at about 72 degrees, and the plunge to the south is about 30 degrees. The ore is, for the most part, a chlorite schist with large veins of secondary quartz and cummingtonite schist The ore is not continuous in any direction, but is localized at the ridges of the very intricate system of anti clinal folds. This property has been in active production since its establishment in 1876, except for a period during World War II. The incentive, or contract pay system, has been a gradual process that has been developed by the trial-and-error method down through the years. In looking over the old records, hand-shoveling was paid on an incentive basis as far back as 1916. Since this time, the contract system has grown until it now includes almost all types of underground work - except haulage and maintenance work

Jan 1, 1960

By Kristin K. Mueller, Lucie Coudert, Thi Yen Chau Nguyen, Lan Huong Tran, Jean‑François Blais, Guy Mercier

Fluorite (calcium fluoride—CaF2), also known as fluorspar, is an industrial mineral used in metallurgy, hydrofluoric acid production, and ceramics manufacturing. Based on the results from a previous study, a low-grade fluorspar by-product (20.0% CaF2) originating from the exploitation of a rare earth carbonatite deposit can be improved to 75.4% by combining magnetic separation and acid leaching. The present research aimed to develop and optimize a column flotation process to increase the purity of this fluorspar by-product by removing residual silicate minerals and meeting the requirements for ceramic manufacturing (> 85% CaF2). The optimal flotation conditions required for maximizing the recovery and improving the grade of a fluorspar by-product were identified using a conventional approach combined with a response surface methodology (Box-Behnken design). Optimal fluorspar flotation was achieved under the following conditions: 3.6 g/kg of sodium oleate as the collector, 2 g/kg of sodium silicate as the pH modifier and depressant, a conditioning time of 35 min, a flotation time of 7 min, and a solid-to-liquid ratio (S/L) of the pulp of 5%. Under these conditions, 86.8% fluorspar recovery was achieved, and the grade increased from 76.5% in the feed (metallurgical grade) to 88.6% (ceramic grade) in the final concentrate. The silicon content decreased from 5.66% in the feed to 1.12% in the fluorspar concentrate. Using magnetic separation before the flotation improves the final content of fluorspar in the concentrate with the final grade of 94.4%.

Sep 9, 2022

By J. A. Herbst

A state of the art computer simulation package, named UTAH-MODSIM is being developed. This package can run on a mainframe (eg. UNIVAC) as well as on a microcomputer (eg. IBM/PC with at least 512 kBytes of core memory). Friendliness was the major concern in developing this software. The user simply generates a complete flowsheet by presenting the flowsheet on a graphics terminal. This flowsheet defines the circuit to be simulated. With the minimum required data, the user can obtain a complete mass and water balances within a few minutes. Moreover, this package will provide scale-up and capital cost information of specified equipment relevant to design. In order to illustrate the utility of this software, three design examples are given. They are: a) A typical multistage crushing plant. b) A reverse closed grinding circuit comparing one stage with two stage classification. c) A standard closed grinding circuit suitable to liberate a specified fraction of chalcopyrite from a copper ore.

Jan 1, 1986