Search Documents

Of the twelve known ore zones on the Sunro property, acquired by Cowichan Copper Co., only the "B" and "C" orebodies of the "River Zone" had been explored sufficiently to indicate the grade and tonnage. The "B" zone was selected for initial production. The portion of this orebody above the main adit level was developed for horizontal-ring, longhole mining. Ore from the stope would be scraped directly to the coarse ore bin. The lack of a suitable mill site on surface, as well as the 8,000-ft. tramming distance, led naturally to the installation ground. I N November, 1960, a lease was obtained by Co-wichan Copper Co. Ltd. (N.P.L.) from Sunro Mines Ltd., covering the main ore (River) zone of the Sunro property. A total of twelve zones had been located on the property. Nine of these lay within the leased area. With the exception of the "B" and "C" orebodies of the River Zone, there had been insufficient exploration for tonnage and grade calculations. Exploration by previous companies had

Jan 1, 1965

By Jr. Watts, B. K. Cantrell, K. L. Bickel, J. F. McDonald

"A field trial was conducted at an underground gold mine to evaluate diesel fuel derived from soybean oil (soy-methyl-esters or “biodiesel”) as an alternative to commercial, low-sulphur, number 2 diesel fuel (D2). A 2.7 m3, 18-ton load-haul-dump (LHD) unit, powered by a naturally aspirated, indirect injection (pre-chamber), 100 kW diesel engine was used as the test vehicle. The LHD was equipped with a diesel oxidation catalyst. The LHD operated satisfactorily on the biodiesel fuel. Operators observed a slight decrease in power and an absence of black smoke.Diesel particulate matter (DPM) concentrations were monitored for a six-week period while the LHD was operated with either the biodiesel fuel or the D2 fuel. DPM concentrations were measured in the mining section’s clean air intake, exhaust and on the LHD. Reduction in DPM emissions was determined from the measured difference in DPM concentrations between the clean air intake and the exhaust. The biodiesel fuel reduced energyspecific DPM emissions approximately 75%, from 3.6 ± 1.8 g/kW-hr to 0.86 ± 0.27 g/kWhr. Time-weighted average DPM exposure, measured near the LHD operator, was reduced from 0.67 ± 0.13 mg/sm3 to 0.28 ± 0.12 mg/sm3, or approximately 58%, when the biodiesel fuel was used. IntroductionDiesel exhaust consists of noxious gases and diesel particulate matter (DPM). Recent attention has focussed on the potential carcinogenicity of DPM and the potential health impact on miners. The National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as a “potential occupational carcinogen”, and that reductions in workplace exposure would reduce cancer risks (NIOSH, 1988). The International Agency for Research on Cancer (IARC) declared that “diesel engine exhaust is probably carcinogenic to humans” (IARC, 1989)."

Jan 1, 1997

By Rakesh Kumar, Rajabrahma K., A. K. Verma, V. Mukesh

"In this study, laboratory investigation as well as numerical investigation is carried out to ascertain the transition from one mode to another for Semi-circular bend setup. Laboratory investigation is carried by varying the span length (s/2R); crack length (a/R); notch angle (a); and notch thickness (t). The specimen consists of cement, sand and water mixture in a ratio of 1:1:0.5 by weight and are prepared as per the ISRM standards (2014). Tests are conducted by a servo controlled universal testing machine at a strain rate of 0.2 mm/ min. The results are collected in terms of failure load, crack mouth opening displacement (CMOD) and images of crack initiation and propagation.Image analysis of laboratory tested samples shows that crack initiates at the notch tip when the notch inclination angle is 0°. As the notch angle increases (i.e. 30° and 60°) the fracture begins to initiate behind the notch tip. The direction of crack propagation in front and back side of the sample is same for notch inclination angle is 0° whereas it differs more and more as crack inclination increases. The transition represents the change in mode of failure from mode I (0°), mode II (30°) and mixed mode I/II fracture (60°).Finite element method used to find the transition based on MTS failure criterion. The inclination of notch is varied like 40, 42, 44, 45, and 50 deg and FEM analysis shows that the transition from mode-I to Mode-II take place at 49 deg. The same procedure can be extended to find the transition from mode-II to mode-III."

Jan 1, 2015

By G. M. Brownell

Introduction Within the past year a new deposit of gypsum has been opened up and brought into production in the Province of Manitoba. Until 1930, Manitoba's entire production came from Gypsumville, northwest of Winnipeg, at mile 161 on the Gypsumville branch of the Canadian National railway. However, during 1930 a gypsum bed was opened up at a point one mile south of the village of Amaranth, forty miles north of Portage la Paririe, on the west side of lake Manitoba (See Figure 1). Although no exposure has yet been discovered, the presence of gypsum below the surface in that district has been known for many years as the result of drilling for water. In 1929, J. R. Spear (1), of Winnipeg, interested some local capital in the possibility of .finding commercial deposits of gypsum, and, after some exploration work in the area with a well drill, the Amaranth deposit was located. Sixteen holes were put down at intervals of 400 or 500 feet, all of which encountered what appeared to be a continuous bed of gypsum, about thirty-eight feet thick, at a depth of 92 feet. The extent of the deposit has not yet been determined.

Jan 1, 1931

By W. G. Worcester

Generally speaking, the term 'clay' appears to convey but little to the average layman other than of a sticky substance to be rigidly avoided when making a cross-country drive in the family ark- especially so if the chains have been left behind. On the other hand, the technical ceramic; engineer, though his chariot be bogged in the self-same mud-holes, will, more than likely, be planning on ways and means for the conversion of the troublesome gumbo into paving bricks over which all might ride with pleasure and security. However, to come to the point, the term 'clay' bears much the same relation to the ceramic world that the term 'ore' does to the metallurgical; in other words, as there are many kinds of ores, so also are there many kinds of clays, and it therefore becomes necessary to classify and sub-classify them previous to a discussion of their relative values and importance. Hence, a brief digression will be made from the main topic of this paper in order to enumerate and classify a number of the more important types of clays. By so doing, the relative position of Saskatchewan clays, later discussed, will be better understood.

Jan 1, 1929

By D. W. Euler, D. G. Brophey

"In an attempt to address the issue of rising labour costs, and to improve productivity, a laser-based system to guide underground LHDs and trucks has been developed. This comprehensive system is known as the Opti-Trak system.Essentially, the vehicle is equipped with front and rear-mounted lasers which scan a reference strip mounted on the drift back. The vehicle follows this reference strip and in addition, based on reflective bar codes mounted beside the reference strip, initiates certain functions (i.e. dump cycle, speed change, brake check, etc.). Any programming that is drift-specific is handled by the positioning of the reference strips and bar codes. Consequently, the vehicle can easily travel to many different haulageways or branches, providing the reference strip and bar codes are in place.The advantages of this system are an immediate elimination of haulage operator costs and an increase in available hauling time to 7 hours out of an 8-hour shift as compared to the typical 5Y2 out of 8 hours that a manned haulage system offers.This paper describes the Opti-Trak system and the benefits to be realized from automation of mine haulage requirements."

Jan 1, 1994

By M. Courtin, D. Berthelot, M. Haggis, D. McClarty, R. Payne

Over forty years of uranium mining in the Elliot Lake region of Ontario (1956–1996) has resulted in the production of over 300 million pounds of uranium. With the completion of mining activity, Rio Algom Limited and Denison Mines Limited are utilizing progressive environmental technologies and management systems to reduce and manage the environmental risks associated with the 150 million tonnes of potentially acid-generating tailings in nine regional waste management areas. Water covers designed to reduce oxygen entry and, thereby, significantly inhibit acid generation, have been applied at six of the sites with the Quirke site serving as a demonstration site for the Mine Environmental Neutral Drainage program. All five of Rio Algom Limited’s effluent treatment plants are monitored and controlled from a central control station utilizing a Supervisory Control and Data Acquisition (SCADA) system based on “Fix Dmacs” technology. Scheduling, auditing and reporting of plant operating and environmental monitoring programs for the entire watershed are controlled utilizing the Regional Environmental Information Management System (REIMS). Proper application of these technologies and management systems facilitates delivery of cost-effective environmental monitoring, care and maintenance programs at these sites and provides tools to demonstrate compliance with all environmental performance criteria.

Jan 1, 1999

By M. Boher, J. Lehmann, M. C. Kaerlé

"In the production of high quality steel, the understanding of the interactions between liquid steel and refractories and of their effect on steel purity and cleanness are becoming more and more important.An experimental study has been per-formed in order to estimate the importance of the reaction between a MgO-based tundish refractory and an Al-killed steel. The results show a pollution of the liquid steel:•the silicon content of the liquid steel increases due to the reduction of the silica of the refractory by the aluminum contained in the steel; and•a reoxidation of the steel occurs and the formation of an oxide layer on the refracto-ry, mainly composed of spinel crystals and of Ca-aluminates is observed.The transfer mechanisms of the various elements are analyzed."

Jan 1, 1997

By Y. Tang

"Rare earth elements (REEs) have many key applications in traditional and advanced technologies. A shortage of several critical REEs is expected due to the discrepancy between the availability of REEs from REE deposits and the REE demand from the market. REE recovery and separation from secondary resources such as uranium wastes and recycled materials might help balance the shortfall in a cost-effective way. This paper presents data concerning the recovery of heavy REEs (HREEs) from uranium raffinate. It also discusses the design, commissioning, and operation of a solvent extraction pilot plant for the separation of REEs.RÉSUMÉ Les éléments des terres rares (ÉTR) trouvent de nombreuses applications importantes dans les technologies classiques et de pointe. On prévoit une pénurie de plusieurs ÉTR critiques en raison des divergences constatées entre la disponibilité des ÉTR provenant de gisement d’éléments des terres rares, et la demande d’ÉTR sur le marché. La récupération et la séparation des ÉTR à partir de ressources secondaires telles que les déchets générés par le traitement du minerai d’uranium et les matériaux recyclés pourraient contribuer à équilibrer cette pénurie de manière rentable. Cet article présente des données relatives à la récupération des ÉTR lourds (HREE, de l’anglais heavy REEs) à partir de raffinat d’uranium. Il aborde également la question de la conception, de la mise en service et de l’exploitation d’une usine pilote d’extraction par solvants pour la séparation des ÉTR INTRODUCTIONSignificant amounts of strategic specialty heavy rare earth elements (HREEs) are present in waste streams in Saskatchewan uranium operations. Selective precipitation including neutralization, oxalate, and double-salt precipitation, as well as sulfide precipitation, ion exchange (IX), and solvent extraction (SX) are commonly used technologies for the recovery and purification of rare earth element (REE) solutions. REE oxalate precipitation can effectively remove Fe, Al, Ca, Si, and other impurities by taking advantage of the solubility difference between REE oxalates and impurities in the acidic solution (Xu, 2005)."

Jan 1, 2018

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed.The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grade, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the final cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure I."

Jan 1, 1995

By N. Samman, S. N. Lau

"A series of new, grease-based, solvent free open gear lubricants were developed to meet the demanding service requirements of mining equipment. The use of these products has resulted in better performance under conditions of temperature extremes and in terms of longer component lives. They have gained widespread acceptance within the mining communities for such applications as the lubrication of mining shovels, draglines and ball mills.These products are WHMIS non-controlled and are environmentally acceptable. The benefits and advantages of using this type of product to lubricate mining equipment as well as the field evaluation and experience will be discussed."

Jan 1, 2002

By John W. Bell

A FEW years ago the writer had the privilege of examining a piece of apparatus in the Forest Products Laboratory of McGill University which engaged his attention. The Forest Products Laboratory has an excellent installation of wood-grinding machinery, and the officials in charge were naturally interested in acquiring means for estimating the fineness of various wood grinds. The problem was referred to Dr. O. Maass ( l ). Dr. Maass designed a piece of equipment to measure the surface of a wood grind and derived an equation applicable in calculating its value, as follows : After inspecting this apparatus, the writer was disposed to believe that, with some modifications, Dr. Maass' ingenious idea might be utilized to measure the surface of mineral powders. Obviously, some difficulty would be found in maintaining an even suspension of mineral particles of high specific gravity compared to that of wood pulp. The writer will not bore the reader with a description of the various machines built and tried out. Some of these were satisfactory enough to obtain some valuable information, and to bring to light a difficulty which threatened to bring the investigation to an abrupt ending. For the mineral quartz, it was found that Kin the formula above stated was not a constant.

Jan 1, 1944

By K. H. Kretzschmar, M. A. Smith

A brief review of the rapid growth of ACT in Western Canada is presented. It is remarked that this rap-id growth has been accompanied by a heterogeneous approach to design. A more rational and consistent approach is suggested, together with the assumptions on which this approach is based. The operating history of some existing installations is discussed briefly, and conditions necessary for the continued growth of ACT are outlined.

Jan 1, 1960

By T E. Tibbetts

This paper deals with coal sampling in general and with mechanical coal sampling in particular. The necessity of obtaining representative samples is emphasized. Other sections of the paper are devoted to the design and selection of automatic samplers, with a consideration of the three main types, and the testing, operation and maintenance of these samplers. The cost of the installation of an automated sampling system must be related to the value of the material to be sampled, to the volume of coal involved, and to the savings in labour and economy which can be achieved. Introduction T HE Committee?:; on Coal Sampling of the Coal Study Subsection, Thermal Power Section (Eastern Zone), Canadian Electrical Association, was established in November, 1963, to "study the various problem areas of coal sampling." The first undertaking of the Committee was to at-tempt to survey the problem areas of coal sampling through an evaluation of coal sampling difficulties as experienced at both the plant design and operational levels within the electric utilities represented on the Committee. The results of this enquiry indicated that satisfactory answers to almost any conceivable

Jan 1, 1965

By L. T. Loe, A. S. Norsk, Mo i. Rana

High production rate and good stability demand the optimization of all phases of electric pig iron smelting. This is important with respect to slag chemistry, which to a large extent regulates the process temperature in electric smelting. Controlled basicity and slag volume. and a satisfactory screen analysis of the reduction material and sinter, are of the utmost importance for smooth furnace operation. Large variations in slag volume and in B/ A and C/Fe ratio will have an influence on the furnace resistance and thus the specific energy development in the furnace, which lead to variable reduction of SiO.. The result will be variable hot -metal quality and un-stable furnace operation.

Jan 1, 1970

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. T HE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept Iles,

Jan 1, 1965

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. THE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept-lies, a seaport

Jan 1, 1965

By D. Campbell Mackenzie

THIS paper is submitted primarily to put on record the results of a number of experiments carried out at the Wingdam mine of Consolidated Gold Alluvials of B.C., Ltd., with the object of establishing a reliable method of concentration of 'wash' and a maximum recovery of gold from the concentrate. It will be generally admitted that, during the last two decades, a tremendous amount of research work has been carried out, both by private companies and Government departments, with a view to improving the technique of the recovery of gold .from quartz veins or lodes. So thorough have been these investigations that milling practice at a modern quartz gold mine is almost an exact science, carried out with meticulous accuracy. In placer mining, on the other hand, very little departure from old traditional methods can be noted, with the exception perhaps of the more modern gold dredges. This may be due to the fact that the concentration of placer gravels, up to a certain point, is comparatively easy. Only a simple equipment of sluice box and riffies seems necessary where the gold is coarse and the gravel free from clay. In the early days of placer mining, when claims were rich and fairly 5hallow, nobody worried very much about fine gold; and, if clay was present, an enlarged dump box was constructed in which the gravel was subjected to a rather desultory puddling. That large quantities of gold are lost in normal placer practice is generally admitted. Some 26 years ago, I had inspectorial charge of many bucket dredges on the Ovens river, in Australia. Occasionally it was necessary for a dredge to work through its own tailing to reach a new section, and almost without exception enough gold was recovered from these tailings to defray the total cost of moving the dredge. Since those days, the technique of gold recovery in dredging has been considerably improved and it is still receiving close attention. Outside of dredge mining, most placer operations, deep or otherwise, are as they were-notorious gold losers, paying little attention to the recovery of fine gold and taking an absurd amount of time over each clean-up. In the Cariboo district of British Columbia, the alluvial gold is usual y associated with varying quantities of black sand (magnetic) and grey sand (non-magnetic); and it can be taken as axiomatic that, if you save all the black sand and grey sand, you save practically all the gold. It is on this hypothesis that we have carried out our research work and brought our recovery system up to its present highly satisfactory standard.

Jan 1, 1937

By D. C. Sharpstone

THE Polaris-Taku mine is a new gold property, situated in the far north-west corner of British Columbia. Production was started in November, 1937, at the rate of 150 tons a day, and recently has been increased to 200 tons. The property, which promises to become one of British Columbia's important gold mines, was developed and brought into production in twenty-nine months after work was started on it as a virtual prospect in June, 1935, by Edward C. Congdon and associates. Inaccessibility, extraordinarily complicated geological problems, and difficult metallurgy retarded development of the property before acquisition by the present interests, an::l, in fact, discouraged two companies that had spent substantial sums upon it from continuing development. This paper is concerned with reviewing the development of the property and describing the principal features of the geology, the mining and metallurgical practices, and the equipment employed. Acknowledgments The writer is indebted to Mr. Edward C. Congdon, President of the Polaris-Taku Mining Company, and to various members of the mine staff for their assistance in assembling the data for this paper. Special thanks are due to Mr. George G. Griswold, Jr., of Butte, Montana, who generously and painstakingly prepared the section dealing with milling and power. Microscopic studies of ores were made by Professors Frank Grout an::l G. M. Schwartz, of the University of Minnesota, and by Mr. Griswold.

Jan 1, 1938

By C. R. Larsen, R. G. Bradburn, A. L. Mular, B. C. Flintoff

"Following the acquisition of grinding- circuit data at Brenda Mines Limited for simulation purposes, various methods to mass balance the circuit were evaluated. Unfortunately, different answers were obtained for different balancing methods. A data-adjustment procedure was therefore developed. The procedure assumes that all ""best-fit"" criterion. A search is conducted with the minimum set of water masses and narrow size ranges of solids around the circuit (called search variables), which permit the computation of any of the measured data points. Search variables are used to calculate measured values for an objective function of the form: [ ] where W, is a weighting factor•, M1 is a measured value and M. is a corresponding . value calculated from search vanables. The best values of M, are those which minimize R. The above method is compared with others that have been utilized for mass balancing circuits."

Jan 1, 1976