Search Documents

By Roland Trunk, Marcel Imbach, Yves Boissonnas, Jan Vesely

"INTRODUCTION The expansion of the Suez Canal, which runs between the Mediterranean and Red Sea, is at the top of Egypt’s economic agenda. The £8 billion development plan includes a new channel alongside the existing one which will double the number of ships able to pass each day and several tunnels to connect the Sinai peninsula to the main part of Egypt. The Egyptian government ordered three new tunnels under the Suez Canal in the area of Port Said as part of the Canal Region Development Plan. The three tunnels will contribute to the North Sinai expansion, helping to create a vast industrial zone and completing the coastal road extension from Rafah to Nuewiba. Two of these three tunnels will be allocated for roads and the third for railway traffic. A further part of the Suez Canal development mega project are an additional six tunnels in the area of Ismailia and Suez. The focus of this paper is on the two road tunnels in Port Said and will give an overview of the project and the challenges encountered regarding the technical complexity and tight time schedule both in its design and execution. PROJECT OVERVIEW The tunnels will be built in the area of Port Said (see Figure 1) which is the most northern part of the Suez Canal.The road alignment connects the Port Fuad Road in the east bank of the Suez Canal to the Port Said-Ismailia highway in the west bank with a dual carriageway section. Each of the carriageways has two lanes. The bored diameter of the 2.8 km long road tunnels is 13.050 m and will be driven with two Mix-Shield TBMs. The distance between the two tunnel axes is planned with 42.5 m (discussion about a reduction are ongoing). The width of the Suez Canal is around 340 m at upper level and around 170 m at the bottom. During the TBM drive, three main geological layers are expected. Below a depth of around 40 m in a very soft clay layer, a dense to silty sand layer is predicted. Within the sand layer another silty hard clay is expected in different depths with variable thickness. After finishing the excavation of the road tunnels, the same TBM will be used for the railway tunnel. The lowest points of the road tunnels will be located 59 m below the surface (tunnel invert to surface) and only 18 m of ground cover exists between the tunnel crown and the Suez Canal invert. Minimum ground cover over the tunnel crown is approximately nine meters at the tunnel portals."

Jan 1, 2016

The properties of interfacial water at hydrophilic surfaces are of great importance in many technological areas including flotation, solid-liquid separation, dispersion and emulsions, flocculation, adsorption, corrosion, and soil contamination. This paper examines the use of FTIR/internal reflection spectroscopy (FTIR/IRS) to study the spectral characteristics of interfacial water at silica surfaces. FTIR spectra were characterized by consideration of the OH stretching region (3000-3800 cm-1) associated with the vibrational spectra of interfacial water. The broad peak in this region was deconvoluted in order to isolate overlapping spectral features that describe the nature of hydrogen bonding in interfacial water. Three distinct bands were found; -3600 cm-1 (free OH), -3400 cm-1 (incomplete tetrahedral coordination), and -3240 cm-1 (complete tetrahedral coordination) and the variation of their intensities with pH was found to be significant. This spectral information helps to explain orientation and bond ordering of interfacial water molecules at hydrophilic surfaces.

Jan 1, 1998

By J. Noll, D. Yantek, B. Kendall, J. A. Organiscak

"A self-tramming remotely controlled mobile Dry Scrubber (DS) was developed by J. H. Fletcher and Co. under a contract with the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research (NIOSH OMSHR) to reduce exposure of miners to airborne dust. NIOSH OMSHR laboratory testing showed that the DS averaged greater than 95% dust removal efficiency with the disposable filters and averaged 88% and 90%, respectively, for the optional washable filters in their pre-washed and post-washed test conditions. Although the washable filters could be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-minute washing period. The DS’s velocity pressure regulated variable frequency drive (VFD) fan maintained a relatively consistent airflow near the targeted 1.43 and 4.25 m3/s (3000 and 9000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60 Hz fan motor frequency or horsepower rating at 2610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the DS also showed that the outlet side of the scrubber was noisier and the loaded filters increased sound levels as compared to clean filters at the same airflow quantities. With loaded filters the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level (PEL) of 90 dB(A) at or below this airflow quantity (1). The DS’s washable filters were not used during field testing because of their lower respirable dust removal efficiency and the airborne dust generated from filter washing. Field testing the DS with the disposable filters at two underground coal mine sections showed that it can clean a portion of the section return air and provide about a 50% dust reduction at the face area downstream of the continuous miner (CM) operation. INTRODUCTION Coal mine worker overexposure to coal and quartz dust continues to be a problem at underground coal mining operations in the U.S. The U.S. Mine Safety and Health Administration (MSHA) recently changed the standard for coal mine worker respirable dust exposure from 2.0 mg/m3 average during an eight-hour shift to 1.5 mg/m3 average over the actual working shift, effective as of August 1, 2016 (1). If more than 0.1 mg/m3 quartz mass is found in the coal mine worker dust sample, the applicable respirable dust standard is further reduced to the quotient of 10 divided by the percentage of the quartz in the sample (1). Over 90% of the mechanized mining units operating in U.S. underground coal mines are continuous mining machines (2). MSHA inspector dust samples from 2009 to 2012 showed that 3.7% of continuous miner operators exceeded the 2.0 mg/m3 dust standard, while 8.8% of these dust samples exceeded the new 1.5 mg/m3 dust standard and 9.7% of these samples exceeded the reduced quartz standard (3). Additionally, roof bolter dust samples at these mechanized mining units during this same period have exceeded the 2.0 mg/m3, 1.5 mg/m3, and reduced quartz levels at 1.1%, 3.7%, and 10.6%, respectively (3)."

Jan 1, 2016

By J. Noll, D. Yantek, J. Organiscak

The Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) conducted laboratory testing of a self-tramming, remotely controlled mobile Dry Scrubber (DS) that J.H. Fletcher and Co. developed under a contract with NIOSH OMSHR to reduce the exposure of miners to airborne dust. The scrubber was found to average greater than 95 percent dust removal efficiency with disposable filters, and 88 and 90 percent, respectively, with optional washable filters in their prewash and post-wash test conditions. Although the washable filters can be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-min washing period. The scrubber’s velocity-pressure-regulated variablefrequency- drive fan maintained relatively consistent airflow near the targeted 1.42 and 4.25 m3/s (3,000 and 9,000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60-Hz fan motor frequency or horsepower rating at 2,610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8,420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the scrubber showed that the outlet side of the scrubber was noisier, and the loaded filters increased sound levels compared with clean filters at the same airflow quantities. With loaded filters, the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6,000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level — under Title 30 Code of Federal Regulations Part 62.101— of 90 dB(A) at or below this airflow quantity. The scrubber’s washable filters were not used during field-testing because of their lower respirable dust removal efficiency and the airborne dust generated by filter washing. Field-testing the scrubber with disposable filters at two underground coal mine sections showed that it could clean a portion of the section return air and provide dust reduction of about 50 percent at the face area downstream of the continuous-miner operation.

Jan 1, 2016

By James N. Brentz

This paper deals briefly with the problem of efficiently selecting the most cost effective haulage truck. Problems and factors are identified that effect productivity and operating cost. Despite the sophistication of computerized vehicle simulation programs, there is a wide disparity in accuracy and methodology, particularly in dealing with the various elements of cost.

Jan 1, 1984

By Jorge Amaya, Nelson Morales Varela, Francisco Saavedra, Gonzalo Nelis, René Gómez

Precedence constraints are broadly used in mathematical models and algorithms for mine planning to model, for example, slope angles in open pit operations or connectivity in underground mines. Unfortunately, these constraints do not capture relevant geometrical aspects for the design of the mine like minimum bottom space of pits or smoothness of the economic envelope in block caves. In this work, we present different approaches that utilize precedence constraints generating economic envelops that are more suitable for design purposes. The numerical experiences show that the proposed techniques produce high value envelops with better geometrical properties and that the methods proposed can be computed efficiently.

Jun 25, 2023

By Stanisław Lasocki

We present an algorithm to integrate the uncertainties of mean activity rate and magnitude cumulative distribution function in the interval estimation of the primary seismic hazard parameters: the exceedance probability and the mean return period. The algorithm is applicable for both the parametric and nonparametric modeling of magnitude distribution. When the Gutenberg-Richter relation-based parametric model of magnitude distribution is used, the interval estimation of its parameters is based on the asymptotic normality of the maximum likelihood estimators. When the nonparametric kernel estimation of magnitude distribution is used, we apply the iterated bias-corrected and accelerated method for the interval estimation, based on the smoothed bootstrap and second-order bootstrap samples. Previous studies indicated that the uncertainty of mean activity rate significantly affects the interval estimates of hazard functions only when the activity rate is low and the inference period is not long (Orlecka-Sikora & Lasocki 2017). With increasing mean activity rate, the uncertainty of magnitude distribution dominates over the uncertainty of mean activity rate in the aggregated uncertainty of the hazard functions. The provided algorithm is generic and can be applied to capture the uncertainty of any multiparameter function from the uncertainties of its parameters. Here we present a further development of the algorithm developed by Orlecka-Sikora & Lasocki (2017) by presenting its implementation in the Traffic Light System approach. As an example of use, we present the confidence intervals estimation of hazard parameters for the datasets related to induced seismicity accompanying underground exploitation of copper ore in the Legnica-Głogów Copper District (LGCD) in Poland. The algorithm is under implementation to the EPISODES platform (https://tcs.ah-epos.eu/) - an IT platform that provides access to integrated research infrastructures of the Thematic Core Service of Anthropogenic Hazards (TCS AH) of EPOS (European Plate Observing System). The algorithm is also a component of the pilot developed within the EPOS SP project (No 871121), which aims to strengthen the interaction with the private sector and the added value for society. The pilot demonstrates the potential of the IS-EPOS platform software applications for the technology-related probabilistic assessment of time-dependent seismic hazard. The pilot supports a Traffic Light System approach. The current seismic hazard is compared to threshold values based on the exceedance probability for a given magnitude.

Apr 26, 2022

By R. R. Bhappu

The metallurgical processing industry is in the midst of a hydrometallurgical revolution with mining companies looking for low cost, energy efficient and environmentally friendly technologies for processing sulfide ores and concentrates. The Intec Copper Process is one of the most advanced of these technologies and has the potential to greatly change the way copper concentrates are treated in the future. Specifically, the Intec process has the ability to be built on a small scale and at mine sites while being much more economic than conventional smelting. Intec Copper has constructed a I tonne of copper per day demonstration plant in Sydney, Australia designed to verify metallurgical and operational performance. This paper will describe the process in more detail and provide preliminary results of the process based on the plant's performance. It will also compare the Intec Copper Process with a few of the competing technologies and evaluate the relative economic merits of Intec.

Jan 1, 1999

By J. R. Koehler

Yield pillar-based gate road designs oftentimes fail to provide mine operators with adequate ground control because of the unknowing misemployment of "critically" sized pillars. A "critical" pillar is one that is too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but is too small to support full abutment loads. To demonstrate the critical pillar concept, a field study of a tapering gate road was conducted by the U.S. Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 1 O.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1995

By T. Marcher, C. Mathiesen, M. Allende, S. Bauer

"A unique pumped hydro storage facility using the ocean as a lower reservoir, combined with solar PV to create consistent, clean power will be presented: the Espejo de Tarapacá Project is comprised of a 300 MW seawater pumped storage hydroelectric plant using the Pacific Ocean as its lower reservoir and an existing natural concavity at the desert as its upper reservoir. The plant site is located in Chile’s northern coast 90 km south of Iquique. The site is characterized by a rocky shoreline and about 600 m of flat terrain moving inland, with an abundance of rock outcrops, after which there is a steep 700 m cliff. The power house and all waterways will be underground. The main focus is to present the rocks being expected in the underground works. As one of the actual most tectonically active regions of the world the seismic activity is particularly relevant and will be outlined in the presentation. INTRODUCTION Valhalla Energy is an independent Chilean-owned power development company. It focuses on the development, ownership and operation of renewable power projects. Valhalla was founded in 2011 with the goal of developing Chile’s natural renewable energy resources and strategically diversifies the country’s energy matrix away from an overdependence on imported fossil fuels. Valhalla began developing pumped storage hydro projects to provide scalable, clean, competitive, and reliable electricity by combining Chile’s superior solar resources with the country’s unique and extensive coastline suitable for storage.The capacity for renewable energy supply is driven by two distinct and unique natural characteristics found in northern Chile: (1) the abundant and reliable solar irradiation in the Atacama Desert and (2) a coastal site that benefits from a steep cliff and a natural concavity both within a relatively small land mass (see Figure 1). There are several potential sites in the northern part of the country that can be developed. The “Espejo de Tarapacá Project” is the first one to be built and subject of the present paper."

Jan 1, 2016

By L. A. Ruth

Introduction The US Department of Energy's Office of Fossil Energy has begun a new approach for developing the ultra-clean energy plants. This approach will allow the nation to continue to use low-cost fossil fuel feedstocks during the early decades of the 21st century. The new approach is called Vision 21. The overall goal is to effectively eliminate, at competitive costs, environmental concerns associated with the use of fossil fuels for producing electricity and transportation fuels. Vision 21 is based on the following three premises: •The nation will need to rely on fossil fuels for a major share of our energy needs well into the 21st century. •It makes good sense to rely on a diverse mix of energy resources, including coal, gas,

Jan 1, 2003

By Arne Paus-Jenssen

The potash industry in Saskatchewan has recently been the focus of much new legislation at the provincial level and, along with other mining industries in Canada, also subject to changes in tax legislation at the federal level. As a result, the industry presently operates under (a) provincial production controls, a prorationing scheme; (b) a new provincial reserve tax on potash only and; (c) a new federal income tax applicable to all mineral industries. The prorating scheme dates back to 1970 and emerged as public policy because of the excess supply situation faced by the international potash industry towards the end of the sixties. This caused special problems for new mines in Saskatchewan and the provincial government decided to intervene. The new tax legislation at provincial and federal levels, both introduced within the last four years, reflects a belief that insufficient revenues accrue to the public sector from natural resources. All mining industries in Canada, including the potash industry, have had their tax positions completely reversed during these four years. Traditionally the mining sector in Canada has been a recipient of substantial tax incentives and has enjoyed low tax rates. This has changed and the mining sector is now one of the most heavily taxed sectors in the economy. In addition, the mining sector has moved from a situation where its rapid development was favoured by governments to a situation where this is no longer the case.

Jan 1, 1976

By D. A. Rice

In pelletizing magnetic iron ore concentrates, about 6 to 18 lb of bentonite binder are added per ton of concentrate during balling to give green and dry strengths to the unfired pellets. The dry bentonite is mixed into the filtercake following the magnetic concentration circuit of the plant. The filtercake contains about 10% moisture, and the water may be of highly variable composition, depending on the particular concentration circuit, its source, and the ore being treated. A knowledge of the parameters that influence the balling operation is essential for optimal efficiency in producing balls strong enough to survive the treatment during transportation from the balling device to the furnace and during the firing operation. Furthermore, very weak unfired pellets probably contribute to high dust losses and poor furnace control. The factors that determine the strength of unfired pellets have received considerable study (1,2,3,4). Tigerschiold and Ilmoni(l) pointed out the significance of the surface area of the particles being pelletized. Merklin and Childs(2) reported on the effect of material size consist, chemical additives such as soda ash, lime, balling time, ball size, and the moisture content of green balls. Iwasaki and Zetterstrom(3) examined the detrimental effects of fatty acids on the pelletizing process. Stone(4) correlated the zeta potential of bentonites with the strength of unfired pellets. He found that, in general, a high negative charge on the bentonite is conducive to good balling. Although studies of pelletizing in the iron ore industry deal with a complex multicomponent system consisting mainly of the iron mineral, bentonite, and water, the last of these has received little attention, particularly with regard to the possible effects of mill water chemistry on the pelletizing process and the strength of unfired pellets. It is widely known that the composition of mill process water is an important variable in unit operations such as flotation, thickening, and filtering and that impure water can lead to poor metallurgical results. The results of the present study indicate that the chemistry of the mill water may be an important variable in the balling operation as well. Knowledge about this variable should contribute to lowering bentonite and oil consumption and to improving furnace performance. Such knowledge can also assist those who use balling in evaluating commercial bentonites for plant use as well as those investigating balling from a more fundamental point of view In this study we have examined 1) the effects of replacing mill process water in the magnetic concentrate filtercake with pure water, and 2) the effects of several chemical impurities that are commonly found in mill process waters upon the strength of unfired pellets. The results are interpreted in terms of the zeta potential of the bentonite and magnetite particles. The data lend support to a suggested mechanism whereby the electrostatic attraction of oppositely charged particle surfaces causes bentonite-bentonite and magnetite-bentonite bonding. This mechanism would also explain why several chemical additives e.g., sodium carbonates and phosphates, have such marked effects on increasing the strength of unfired pellets.

Jan 1, 1971

By G. C. Allen

Selective flocculation is used for the purification of clay minerals. Here we present data from a surface spectroscopic investigation into the polyacrylamides mediated selective flocculation of kaolin from an impure matrix. Use of X-ray photoelectron spectroscopy (XPS) was shown to offer a useful approach for investigating the observed selective separations. In particular, a new small area XPS technique was used to characterize, in situ, the differential competitive, f1occulant adsorption onto mixed kaolin/gangue systems.

Jan 1, 1998

By J. S. Lee

Alkyl hydroxamates are well known collectors for oxide copper minerals as evidenced by the large amount of published literature. Our studies on a wide variety of copper ores from around the world have shown that alkyl hydroxamates will recover most of the "floatable" oxide copper minerals from an ore. They are available commercially, and they offer many advantages over alternative technologies for oxide copper recovery. In spite of this, the full potential of hydroxamates has not been exploited in the industry. The objective of this paper is to provide relevant practical aspects and guidelines to facilitate successful application of hydroxamates in operating plants. A critical analysis of the available information and data, based on several case studies, notation testing, and microscopic analysis indicates that alkyl hydroxamates can effectively recover well-defined oxide minerals of copper, but not copper occurrences such as Cu-bearing goethite (often misidentified as cuprite) which report as Acid Soluble copper in chemical assays. Prior to any notation testing with hydroxamates, it is necessary to assess the various modes of occurrence of Acid Soluble copper using microscopic and microprobe analysis.

Jan 1, 1998

By Robert R. Unterberger

The purpose of this paper is to summarize the research of the past sixteen years on three distinct methods of probing into solid rock. The first method is to use radar of the appropriate frequency. The second method is to use sonar. The third method is of recent vintage and uses techniques of nonlinear sonar also known as parametric sonar. The first two concepts, that of radar and sonar, are common to most people. Very few have heard of nonlinear sonar. Each of the probing techniques were investigated in order to overcome deficiencies in the former technique. Each has its advantages and disadvantages. It should be emphasized that all of these techniques for probing (or seeing) into rock are used in mines, and generally speaking not from the surface. Only in very special cases, such as certain very dry parts of Egypt or Peru, or, for example, the surface of the moon, will these probing techniques work from the surface. The reason for the development of these probing techniques has been to alert miners to possible hazards ahead of mining. Such hazards may be (1) old (unknown) boreholes connected with high pressure water zones above, (2) fractures that might connect to the Gulf of Mexico above the mine, (3) water-filled fractures that threaten the safety of miners, or (4) the discovery of dry faults ahead that can disrupt the planning of future operations.

Jan 1, 1983

Grinding and energy input in stirred media mills are studied as functions of grinding time, stirring speed, media size and density, solid concentration, impeller and tank dimensions and design, and other relevant variables. Ground product size and surface area are determined with respect to the above variables. Changes in energy input and media/pulp rheological properties during grinding are described. The best conditions for grinding limestone in the laboratory stirred media mills have been identified. Equations for correlations involving power and modified Reynolds numbers have been established.

Jan 1, 1995

By J. A. Mielczarski

An infrared external reflection spectroscopy (ERS) technique has been developed to study the structure of the adsorbed layer of ethyl xanthate formed on copper and natural chalcocite (Cu2S) electrodes. The infrared technique provides information concerning the identity and the orientation of the adsorbed species at monolayer and submonolayer coverages. X-ray photoelectron spectroscopy (XPS) studies have also been conducted to monitor changes at the surface. The results show that the first oxidation peak on the voltammograms for copper and the first and second oxidation peaks on the voltammograms for chalcocite electrodes are not characteristic of a chemisorbed xanthate species, which is contrary to what has been reported by other investigators previously. As evidenced by the XPS spectra, there was an increase in sulfur relative to copper on the copper and chalcocite surfaces over the potential region where these oxidation processes occur. The spectroscopic results (ERS, XPS) indicate that the second and third (on copper) and the third and fourth (on chalcocite) oxidation processes recorded on the voltammograms are due to cuprous ethyl xanthate adsorption. The orientation of the adsorbed molecules of xanthate was observed to change with increasing surface coverage. Therefore, it has been concluded that xanthate can modify the copper and chalcocite surface in two different ways. At lower potentials, xanthate is a source of sulfur for the formation of a sulfur-rich surface. At higher potentials, an adsorption layer of cuprous ethyl xanthate is formed. Contact angle measurements show that both of these processes of xanthate surface modification lead to an increase in the hydrophobicity of the substrates.

Jan 1, 1990

By P. H. Qi

Activated carbon loaded with gold from different halide solutions has been characterized by thermal analysis techniques. The mechanism of gold uptake by carbon varies from predominately adsorption for gold iodide to predominately reduction for gold chloride. TGA and DT A measurements confirm the existence of adsorbed gold-halide species within the micropore structure of carbon. These results suggest that the ration of reduced; adsorbed gold increases for gold halides in the order Au-I > Au-Br > Au-Cl. In the case of Au-I, TA results for the loaded carbon were compared with pure compounds of 12, AuI and AuI3.

Jan 1, 1996

By Remo Grandori

"INTRODUCTIONDouble Shield TBMs were introduced in the market in the early seventies with three main targets:• Increase the TBM performances in term of advance per day thanks to the ability to erect a segmental lining simultaneously with the excavation phase.• Be able to advance through unstable and disturbed rocks under the protection of the shields• Provide a finished tunnel by installing a precast lining as the TBM advance.In 2003 SELI developed the design of the Double Shield Universal (DSU) TBM as an evolution of the original Double Shield TBM design.This new TBM design was targeted to improve: the TBM capability to advance through squeezing/converging rock formations under high cover, the telescopic joint design (allowing by such to operate the machine in double shield mode in very weak rock), the capability of the TBM to investigate and treat the ground around and ahead of the tunnel face.In the same lapse of time Single Shield TBMs, originally utilized for soft ground tunnelling, extended progressively their range of application to mix rocks and finally to hard rock tunnelling with increasing performances.This also thanks to the substantial reduction in the installation time of the segmental lining ring that contributed to minimize the TBM stand by time between two consecutive boring strokes.Today the choice between the two types of TBMs needs to be carefully evaluated project by project since one type of TBM may “prevail” in certain geologies and diameters and vice versa.THE VISHNUGAD PIPALKOTI TUNNELThe Vishnugad Pipalkoti Tunnel is part of the 444 MW Vishnugad Pipalkoti Hydro Electric Project (VPHEP) on Alaknanda river in Uttarakhand (India).The Owner is the Indian electric company “Tehry Hydro Development Corporation” (THDC) and the World Bank finances the project.The Headrace Tunnel total length is 13.4 Km and a section of about 12,3km will be excavated by TBM by SELI Overseas (Italy) in subcontract to HCC (India) the General Contractor for the project. The TBM will be delivered ex workshop in March 2016 and it is foreseen to start boring in the second half of 2016.Figure 1 below shows the location of the project and the following Table 1 summarizes the geometrical characteristics of the TBM tunnel."

Jan 1, 2016