Search Documents

By Dieter Froelich, Giles Turcotte

In the near future, Bong Mining Company (BMC) will start mining a new deposit known as Zaweah II which is a narrow iron orebody requiring multiple row blasts with the bench floor as a free face. This called for the development of a new blasting technique. The article delineates the problem and its restrictions related to blasting. It also describes the approach which was taken for developing this new blasting technique which is essentially an application of the cratering theory with near spherical charges. Basic crater tests were conducted using various combinations of hole sizes, explosive strengths and delay patterns. From the results obtained, several alternatives were considered for production blasts and the most promising ones were evaluated.

Jan 1, 1980

By Albert G. Funk, Gary M. Thornley

The available energy of aluminized ANFO and aluminized slurry blasting agents has been measured by seismic methods, calculated theoretically, and compared. With aluminized ANFO it is concluded that aluminum concentrations should be restricted to less than 10 percent because of diminished energy yields at high aluminum concentrations. However, with aluminized slurry it is concluded that efficient use of aluminum can be made at aluminum concert"rations up to 18 percent. It is further concluded that the difference in efficiency of use of aluminum by these two classes of blasting agents results from a higher contribution to useful work from the condensed detonation products of the relatively higher density aluminized slurry blasting agent.

Jan 1, 1981

By Dworzak, Andrzej Biessikirski, Jozef Pyra

During the detonation process 20-30% of the energy is being consumed only on the quarrying pro-cess. The remaining amount of the energy generates harmful effects such as: shock wave, acoustic wave, fly rocks and ground vibrations. The ground vibrations effect is the most dangerous especially to structures which are situated nearby an open pit mine.

Jan 1, 2015

By R L. Keller

Hong Kong has some of the most restrictive practices regarding blasting than any place in the world. Regulations regarding vibration limitations are 1 in/sec for structures and 0.5 in/sec (or even less) for most utilities; with no recognition of frequency response or adjustment. The Hong Kong Geotechnical Engineering Office has one of the most conservative approaches and protective guidelines for pre-blast assessment of slopes subjected to blast vibration (SEE paper '96). The protective measures to control flyrock generally required by the Mines Division are additionally very stringent. It is not uncommon for the costs associated with protective measures or methods which must be employed to exceed the cost of the drilling and blasting itself - or to waiver blasting application unfeasible altogether. From these restrictions it can easily be imagined how blasting in this urban environment would be most challenging.

Jan 1, 1997

By C. Lownds, U. Steiner

In 2008 a paper from the same source describing four actual cases of exposure of electronic detonators to lightning strikes was presented. It was shown that electronic detonators, like other initiation systems, are vulnerable to very close or direct lightning strikes. At the time of submitting this abstract no further incidents with lightning have been experienced. As a result of those original incidents, and in order to understand how the safety devices inside electronic detonators break down, two series of tests have been done, each with 2 detonator designs. In the first series detonators were subjected to capacitor discharges up to 6kV and 1kJ in energy. In the second series the intensity was increased to 800kV and 24kJ in energy. In the second series, more electrical energy was delivered to the detonator assembly than the explosive energy of the detonator. In both series both detonators showed a spectacular ability to resist very high discharge energies. The tests are described in detail with supporting photographs. The data for both pin-to-pin and pin-to-case (more relevant to lightning) are presented and discussed. The mechanism of breakdown of safety devices is now understood better and the learning is being used to design more robust products. This high-voltage testing is relevant in understanding how electronic detonators might initiate as a result of a very close or direct lightning strike 1. Orica

Jan 1, 2009

By Lex L. Udy

External detonation generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall.

Jan 1, 1977

By Laurence Neufville

Proper risk assessment and blast design are very desirable to the execution of a blast. Not only will this ensure that it achieves its desired outcome, but the probability of complaints and litigation will be reduced. Blasting engineers rely heavily on site-specific data for analysis and input to the blast design equations, and therefore data collection is critical to this process. The traditional approach to data collection is to carry out site-specific reconnaissance by visiting the site, but the time spent doing so can be reduced if a remote sensing approached is adopted.

Jan 1, 2009

By R Heater, G Glynn

Various small diameter commercial grades of slurry and emulsion explosives were tested and compared. Velocity diameter curves for confined and unconfined charges were established and the effects of temperature and hydrostatic pressure on critical diameters and minimum primer weights were determined.

Jan 1, 1984

By Greg Wyartt

Although electronic detonators and blast initiation systems have been commercially available for several decades, uptake in the Australian mining industry has been very slow when compared to other global mining regions. The safety and operational advantages of electronic initiation are generally well understood in Australia, however there has been a prevailing perception that these advantages do not outweigh the extra financial and technical investments.

Jan 1, 2019

By Italo Onederra, Jason Furtney, Ewan Sellers

The Hybrid Stress Blasting Model (HSBM) is a high level blast modelling research tool which provides results that can still be used implicitly for practical blast design. The code is being developed through an international collaborative research project funded by a consortium of companies which is comprised of explosive, equipment suppliers and major mining houses. A key component of the HSBM is the numerical code and user interface designated as Blo-Up 2.5. To date validation work has focussed on breakage, fragmentation and damage outcomes in controlled laboratory experiments and using large concrete cubes

Jan 1, 2012

By Robert Hopler

INTRODUCTION NOT so very many years ago the farm was about the last place where one would expect to find up-to-date mechanical appliances. Steam, explosives, electricity—the factors which have made the world in general, and America in particular, what it is today— were indispensable for the railroad and the steamboat, the factory and the mine, but the farmer’s work was generally run on a comparatively small scale, and was mostly done by the muscles of men or draft animals. Today, however, the farmer as well as the manufacturer, the contractor and the miner, fully appreciate the value of labor-saving devices. Every up-to date farm, large or small, has modem machinery that tends to reduce the cost of production or to improve farm products.

Jan 1, 2011

By Romel Villanueva, Juan Vasquez

We present the results of our field research on the variation of the density of the gassed explosives and their influence on the blasting results in the Peruvian mines: Yanacocha, Toquepala and Antamina. Currently, 90% of Peruvian mines uses gassed explosives, for their economic and technical benefits. But new practices and design criteria have had to be adopted, and the most important a careful control of the in-hole density, whose variation in the depth of the hole strongly affects the detonation process. For gassed explosives the density varies gradually according to the depth in the hole, due to the pressure on the bubbles by its own weight. The density at the bottom of the hole can reach critical values, which directly affects the start of the detonation in the booster zone with a high probability of nitrous fumes formation. On the other hand, density translates into the amount of explosive and energy available. Therefore, for the optimum performance of the explosive, the minimum and maximum values of the in-hole density must be determined. For the cases studied, the maximum in-hole density and the maximum charge length have been determined. When the charge length is greater than 7.0 m [ 23 ft.] special care must be taken with the cup density, which as a general rule should not exceed the value of 1.15 g/cm3 [71.8 lb/ft3] at the risk of losing the sensitivity at the bottom, also increasing the probability of nitrous fumes, bad fragmentation and finding intact explosive after blasting. In the large holes in Toquepala and Antamina mines, where the charge length can be greater than 9.0 m [29.53 ft]. If the cup density is greater than 1.15 g/cm3 [71.8 lb/ft3] the in-hole density can easily reach a high value of 1.30 g/cm3 [81.16 lb/ft3].

By Robert B. Hopler

The history of bulk loaded explosives begins with the loading of black powder and RRP (Railroad Powder) into vertical boreholes. The early air place, net of black powder and nitrostarch dynamites is covered, as are the brands and formulas of the nitroglycerinsensitized "Bagged" powders.

Jan 1, 1993

By Donald Jonson

Stockholm’s Northern Link, currently Europe’s largest urban road tunnel project, will be about 5 km long from west to east. Running through two separate, mostly parallel tunnels, each with 2-4 lanes, the complex will include numerous entries and exits, as well as a major branch to the north. The total length of tunnel will be 11 km, of which 9 km will be in rock. Over million m3 of rock will be blasted. The Northern Link will open to traffic in 2015. After a 10-year stop to deal with environmental questions regarding Ekoparken, Stockholm’s unique “national city park”, the Northern Link project in the Swedish capital was restarted in the autumn of 2006, with the construction of five works-access tunnels.

Jan 1, 2009

By Lon Santis, David Buckwalter, Ken Steinmetz

This paper describes a magazine security system using two readily available cellular telephone-based technologies. The system is comprised of vibration sensors and remote cameras. The system is used at a Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF) licensed explosives storage location in Pennsylvania to comply with PA Department of Environmental Protection (PADEP) regulations. The system provides instant notification to the licensee via cellular modems, text messaging, phone call, and e-mail. Likewise, the licensee can control the system remotely over the internet and using text messaging commands. The vibration sensors attach to the door of the metal type I magazines magnetically and detect any movement or vibration. The cameras trigger on movement and thermal radiation changes and can also be triggered manually to check alarms received from the vibration sensors. The previous system was comprised of a base unit and magnetic strips. The magnetic strips were powered by a hard line from the control unit and mounted on the doors and top of magazine creating a bond, that when broken triggered an alarm. Our main issues with the unit were the delay in alert times and tech support. Because of these issues, we decided an upgrade was necessary. Compared to that previous system used at this site, these new systems are highly affordable, carefree and reliable.

Jan 1, 2014

By Allan King

Ammonium Nitrate (AN) is most commonly encountered as either a prilled solid or a highly concentrated aqueous solution, with or without organic ( e.g amine) nitrates. Under certain conditions of fire exposure involving prilled or solid AN, the molten state can be formed. The shock sensitivity of the molten material at temperatures greater than 220 Celsius has been found to be much higher than that of the prilled or solid form. Molten AN can be a precursor to events leading up to explosion of a bulk prill storage pile as a result of fire exposure. The explosion hazards presented by molten AN are a function of two factors; 1) its shock sensitivity and the deflagration to detonation ( DDT ) properties of the molten material, and: 2) the ability of large masses of unfueled prilled AN to be initiated and detonate. This paper presents the results of tests designed to determine the shock initiation and DDT properties of the solid ( prilled ) and molten AN.

Jan 1, 2008

By Neal Lee, Braden Lusk, John Silva Castro

One of the most common assumptions regarding the use of ANFO versus utilizing 100% sensitized emulsion is that ANFO “turns over” the muck-pile better, due to the “higher gas volume” supposedly inherent in ANFO. This paper examines this assumption and provides quantitative data for analysis. Total gas volume from each product was evaluated using Orica’s I.D.E.X. Code analysis. This analysis was used to determine if gas volume is a significant contributor to differences in fragmentation and movement between blasts utilizing the two different products. A constant drilling and blasting cost per yard for given cut depth, hole diameter, stemming height and rock type was utilized. The cost per yard was held constant by adjusting patterns considering product, accessory, and drilling costs. Photographic fragmentation analysis, dig rates measured quantitatively through production tracking and time studies and qualitative information about the diggability of the blast provided through video recordings were used to evaluate performance. The data collected during the study is presented and recommendations are made regarding the performance of ANFO and Emulsion holding other variables constant for a limited number of blasts.

Jan 1, 2012

By William Reisz

Many different types of drills coming in a wide range of sizes and configurations are used in the blasting industry today. While each system may have its own unique attributes and capabilities, it may hold its own perils as well. This article will focus primarily on hazards that are mutual to most every type of drilling system.

Jan 1, 2013

By Ed O'Connor, Per-Anders Persson, Manhong Zhou

This chapter deals with the concepts of shock waves and detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the context of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of an explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1997

By Per-Anders Persson

This chapter deals with the concepts of shock wave8 and detonation wavea together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the context of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of an explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of thii chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1998