Search Documents

By Brandon T. Buschmeier, Sonia S. Swift, Michael P. Walker, Frederic Masse

"Ground improvement has undoubtedly become a cost-efficient and effective solution to support the development of poor soil sites. Ground improvement elements, such as Controlled Modulus Columns (CMCs), replace piles by improving the subsurface soils and reducing settlement. As ground improvement becomes more popular, the applications become more creative and ground improvement is being used to control settlements under large structures with tight settlement tolerances.In this paper, we will discuss the use of CMCs to support two (2) large industrial warehouses where soil conditions would normally lead to the use of deep foundations and a structural slab, grade beams, and hung utilities to prevent excess settlement. Each of the sites we will discuss had poor soil conditions in the form of very soft or compressible soil, heterogeneous fill of varying thickness, and environmental contamination. At each site, we developed a design that would allow for the use of Controlled Modulus Columns (CMCs) with a Load Transfer Platform (LTP) in place of the previously-proposed deep foundations. The use of the CMCs also allowed for the use of spread footings and slab on grade construction. The benefits of this value-engineering approach include economy in the foundation system, risk mitigation by not disturbing contaminated soils requiring expensive removal, and ease of access for future sub-slab upgrades with new tenants. Additionally, the use of recycled concrete aggregate as an LTP is more environmentally friendly than placing structural slabs with heavy steel reinforcement.Designing for the settlement of large warehouses is challenging because it requires changing how we typically perform our designs. For most structures, the slab loads are relatively light when compared to the footing loads, whereas for warehouses, the slab is heavily loaded compared to the relatively light footing loads. Thus, it becomes essential to perform three-dimensional analyses to confirm that the proposed CMC layout will provide uniform support of the slab and footing across a variety of loading scenarios (loaded bays vs unloaded or travel bays). The complexity of the designs for these warehouses generated interest in conducting large area load tests over a grid of multiple columns. The performance of the area load tests provided invaluable information on the effectiveness of the LTP and CMC spacing. In this paper, we present a general description of CMC ground improvement, the differences between ground improvement and traditional pile foundations, our typical design methodology for CMC design, and the modifications to that methodology for warehouses."

Jan 1, 2017

By Tanaya Deb, Sujit Kumar Pal

"Experimental investigations are carried out on failure pattern around 2D models of belled anchor piles in dry sand bed of density 15.60 kN/m3 under uplift. The models are having thickness ratio (Ts/Tb) = 0.28, 0.32, 0.38 and 0.46 and total 12 numbers tests are performed on models possessing 45° bell angle and shaft thickness 26 mm. The foundation bed is prepared with alternate dyed and non-dyed sand layers and continued upto reaching embedment ratio of 3, 4 and 5 for each width ratio. The failure points are presented with respect to meridian section of anchor in X-Y coordinate system and the equations formed are of polynomial of degree 3; and R2 values are near about 1. The developed wedge is implemented as three-dimensional axisymmetrical failure surface around similar 3D models. In the horizontal slice method vertical limit equilibrium is used for calculating weight of wedge and mobilized shear (as per Chattopadhyay and Pise, 1986) on the slip surface of each element. The summation of all elementary forces demonstrates gross uplift capacity. The initial and final failure angles are detected and parametric study is conducted on failure pattern as well as predicted net ultimate uplift capacity. Almost all the analytical data are within ± 10% variations with respect to the experimental results of uplift capacity which shows better correlations. INTRODUCTION Belled or enlarged base anchor piles are attractive and economic alternative to the geotechnical engineers for compressive load bearing capacity as well as tension anchorage. These types of anchors may be useful for foundations erected below ground water table. In light weight structures like radar tower, television tower, power pole and outdoor sign pools imbalance horizontal forces due to wind loads, are more than of those self-weight of those structures. Due to chronic tensile loads most possibly from wind loads and associated imbalanced cable tension, the legs of power transmission tower should be properly designed to be safe against resultant pull-out forces. In belled anchor pile, uplift is influenced by embedment ratio, diameter ratio; so, contributions of these parameters on failure surface influence uplift capacity. Balla (1961) first introduced non-linear failure surface in the pattern of circular arc based on Kotter’s equation (1903) and soil friction was assumed to act on slip surface. The predictive mathematical models established by Matsuo (1967), Rao and Kumar (1987), Chattopadhyay and Pise (1986), Saeedy (1987) and Ghaly and Hanna (1994); it was reported that net ultimate uplift capacity was combination of bulk weight of failure wedge and shear resistance along slip surface acting in opposite direction of wedge movement. From the literatures available till date, it reveals that the contribution of mobilised shear and weight of breakout wedge separately, demanding for more clarification depending on the on parameters like embedment ratio, diameter ratio."

Jan 1, 2015

By Anthony L. Reynolds, Clifford J. Wren

"The adoption of a significant pile testing regime, the use of Eurocode 7 as the design standard, the development of lean construction techniques, and lateral thinking in overcoming some considerable construction challenges allowed Stent Foundations to construct the foundations for the new Wembley Stadium, London, on time and within budget. In addition to the piling works for the main stadium, and after significant design development, a large number of extra piles were required to raise the new iconic roof Arch to its final position some 133 metres above the ground. A 1,400m long contiguous bored pile wall was also constructed to allow for excavation and formation of the new pitch. INTRODUCTIONHjstorjcal lntrodyctionWembley Stadium is the 'home of English football'. As long ago as the 1880's, Wembley Park leisure grounds had football pitches and running tracks.In 1918 the British Government began planning a British Empire Exhibition with a stadium as its centrepiece. The Exhibition area covered 219 acres and the area on which a former abandoned tower called Watkins Folly had stood was chosen as the site for the new stadium (http://www.wembleystadium.com).The Empire Stadium, as it was originally known, was designed by architects Sir John Simpson and Maxwell Ayerton and the engineer Sir Owen Williams. It took just 300 days to complete at a cost of £750,000 ($1.4m), and was built using 25,000 tons of ferro concrete, 1,000 tons of steel, and over half a million rivets.The Empire Exhibition was a remarkable event, containing fountains, lakes, gardens, and many pavilions, each representing the architectural style of the countries exhibiting. It was opened on 23rd April 1924 and the final attendance was over 27 million, with 4.5 million admissions to the Empire Stadium alone."

Jan 1, 2005

By Vijaya Bhushan Rao, Jason Redgers

The typical Vibrocompaction projects undertaken in the UAE are on reclaimed Sands. These Sands which are predominantly the crushable, calcareous, carbonate sands found locally as opposed to the more common quartz or silica sands that are featured in most design literature. The famous reclamations such as the iconic Palm Jumeirah in Dubai, often have specification for mitigation of liquefaction induced settlements, bearing capacity increases and total and differential settlement requirements. Often these performance targets are achieved by the means of achieving a particular relative density that are generally measured by a defined Cone Penetration Test, CPT targeting values of cone resistance (Qc), MPa at respective depth zones. In this paper some case studies are presented, where soil suitability for deep compaction by vibratory methods was firstly assessed for suitability using the Massarsch, 1991 compactability chart prior to the application of vibrocompaction and its subsequent evaluation. One such project named the Island Development required 17 to 23m depth of penetration only to treat the lower 5 to 6m of sand above rockhead as eventually the top 15m of sand will be further excavated to allow for the construction of basement. The paper will present pre and post CPT results, the results of initial site calibration trials and evaluation of the completed works.

Oct 1, 2022

By Dewey W. Geary, Rachael V. Bisnett, R. Michael Bivens, Thomas G. Andrews

"The powerhouse for the Red Rock Hydroelectric Project is being constructed at the toe of the existing U.S. Army Corps of Engineers’ Red Rock Dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends though overburden and 40 feet into rock. Prior to rock excavation, a grouting was performed around the excavation for the purpose of increasing the strength of zones of fractured rock. For the majority of the perimeter, the rock was fairly tight and grout takes were relatively low. However, for a 160 foot extent along the landside of the excavation, extensive grouting was required to treat a two to five foot thick zone characterized by artesian flows from grout holes on the order of 20 gallons per minute (gpm) or higher from a voided zone in rock that was partially filled with sand, clay, and rock fragments. This paper discusses the treatment measures used to fill and improve the strength of this zone, which ultimately entailed a combination of thick cement grout and polyurethane grout, holes spaced as close as 18 inches on-center, and two additional rows of grout holes.IntroductionThe Red Rock Hydroelectric Project (Project) is currently under construction at the existing U.S. Army Corps of Engineers’ (USACE) Red Rock Dam on the Des Moines River near Pella, Iowa. At peak generation, the Project will generate up to 55 MW with an average annual energy output of 178 gigawatt-hours.The powerhouse for the Project will be located at the toe of the existing dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends up to a depth of 40 feet into rock through the St. Louis Limestone and terminates in the Warsaw Limestone. Prior to rock excavation, grouting was performed around the excavation for the purpose of improving the strength of zones of fractured rock. An auxiliary benefit of the grouting was reducing seepage into the excavation. Grouting began on July 20, 2015 and ultimately concluded on September 26, 2015.Drilling and grouting occurred as planned on the riverside (southwest) of the excavation along the cellular cofferdam and stilling basin wall (grout holes P-1 through S-13) and on the upstream (northwest) side of the excavation along the secant pile excavation support wall (grout holes P-14 through S-19) (refer to Fig. 1). The rock in these areas was generally tight with relatively low grout takes. However, on the landside (northeast) of the excavation (grout holes P-20 through P-28), partially infilled voids and artesian flows were encountered during drilling generally between depths of about 28 to 40 feet."

Jan 1, 2016

By William G. Ryan, David S. Graham, Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"The St. Croix River Crossing project on the Minnesota-Wisconsin border has been in the process of planning and public debate for two decades, with several changes in alignment. During the course of the earlier planning process in 1995, a drilled shaft load test was performed to obtain preliminary design information. There were some difficulties in maintaining stability within the weak sandstone bearing formation, and the measured axial resistance was relatively low. Subsequent experience by the Minnesota Department of Transportation with similar weak sandstones on the I-35W project suggests that improved construction techniques using modern drilling fluids may offer opportunities for improved performance. During final design in 2012 a second load test program was performed of a full scale test shaft constructed using polymer drilling fluids. The stability of the socket excavation in the weak sandstone appeared to be greatly improved and the measured axial resistance significantly higher.This case history illustrates the excellent performance that drilled shafts can provide in even relatively weak sandstone bedrock as well as the profound influence on axial resistance associated with the construction techniques used. The improved resistance values obtained by the new load test with more recent construction technology allowed the foundation scheme to be substantially optimized with respect to the number and size of required drilled shafts, reducing the size, cost, and risk of the coffercells and footings.IntroductionThe Minnesota Department of Transportation (MnDOT) has awarded the first phase of a bridge construction project that will cross the St. Croix River between Oak Park Heights, MN and St Joseph, WI. The first phase construction contract involves building the river pier substructures including groups of drilled shafts beneath each tower leg. A general location of the bridge project is provided in Figure 1.Prior to award of the construction contract, two separate design-phase axial load tests were performed on non-production drilled shafts with rock sockets. Both tests were static, bottom-up tests using the Osterberg Cell (O-cell). The first test was performed in 1995 when final design and construction was thought to be imminent. After years of public debate and literally, an act of Congress, design of the project was finally restarted and a second load test performed in 2012. The 1995 test was conducted on the Minnesota bank approximately 900 ft southwest of the St. Croix River bank. The 2012 test was conducted in the river about 2,100 ft northeast of the1995 test location. A plan-view of the project indicating the test program locations relative to the bridge alignment is provided in Figure 2."

Jan 1, 2015

By James M. Tantalla, Dwight Metcalf, Roderic A. Ellman Jr.

"The construction of a new low head hydro-electric plant at the Cannelton Lock and Dam required the design and construction of a cofferdam to accommodate a deep excavation extending approximately 150 feet below the Ohio River levels. The new plant, which generates about 390 GWh of electricity annually, is owned by American Municipal Power (AMP). A specialist team was assembled to design and construct the cofferdam, marine dike and CB slurry wall that helped make the project successful and on time for project delivery.Because the new plant diverts water from the locks and dam through a powerhouse to generate power, it would need to be partially in the river to operate properly. To accomplish this, approximately 250,000 square feet of land was reclaimed from the river by construction of a marine dike. The dike, combined with the design and construction of a 150 foot deep cement bentonite (CB) cutoff wall enabled construction of the new plant in the dry. Extensive dewatering analyses were performed using Modflow to evaluate pumping requirements and the number of wells needed to maintain ground water at required levels within the side slopes and final subgrade. A monitoring program consisting of inclinometers, piezometers and movement monitoring points were used to monitor cofferdam stability and performance throughout construction. Detailed two and three dimensional stability analyses that included a parametric study of fluctuating river levels and slurry unit weight were performed to ensure stability and suitable low permeability of the trench during cut-off wall excavation both on land and in the marine dike. The wall was constructed with both a hydromill excavating primary panels and a clamshell following behind to construct secondary panels. Data acquisition systems onboard the excavating equipment allowed for detailed confirmation of the continuity of the wall at each interface between panels. Another challenging aspect was the CB mix design for the trench. The cofferdam required the construction of a 1,300-foot long marine dike downstream of the existing dam up to 100 feet tall founded on existing river sediment to enclose the site and cut-off the seepage into the excavation from the river. Marine dike construction utilized vibro-compaction to pre-densify granular fills placed underwater through which the CB trench extended."

Jan 1, 2016

By Brian Metcalfe, Kord Wissmann, Gianni Martinez

The Middle East consists of vast deserts that reach temperatures up to 50 degrees Celsius, with some areas characterized by endless sand dunes. When the project team selected the location for a large new transportation project, little did they know that the site would be characterized by soft, nearly normally consolidated silt and clay extending below a thin sand crust. Searching for solutions, the design team elected to reinforce the subsurface with Rammed Aggregate Pier® (RAP) ground improvement elements and desired verification that the novel method would stand the test of prolonged static loads. Because the concrete pavements would serve to spread the load, a “zone load test” was performed, consisting of applying a uniform bearing pressure of 150 kPa over a 7.5m square concrete footing. Unlike individual pier load tests, the zone test allowed the project engineers the opportunity to confirm design parameter values under large-loading area conditions, a situation not often available to most designers. This paper presents the results of the zone load test whose results may be interpreted to better understand design parameter values. This paper is of particular significance because it adds a value contribution to the relatively few numbers of “group load tests” available in the literature for ground improvement applications.

May 1, 2022

By Adrian Gygax, Sarah Gaib, Rod Kostaschuk

The British Columbia Ministry of Transportation and Infrastructure (Ministry) recently completed a slope stabilization project at Ten Mile Slide on Highway 99. The highway is an essential part of the road network connecting the British Columbia (BC) coast with the interior of the province. The landslide was first identified in the mid-1980s and has retrogressed more than 250 m upslope since then, leading to continual and expensive repairs to the highway. The Ministry engaged BGC Engineering Ltd. (BGC) and their structural sub-consultant Gygax Engineering Associates Ltd. (GEA) to develop a stabilization scheme that would halt the slide with an acceptable level of residual risk. The design required careful consideration of construction stages and the stresses induced in the structural components as the slide movement was progressively stopped as construction advanced. Four stabilization design options were shortlisted with the preferred option selected in Fall 2016. The selected solution comprised the construction of five rows of post-tensioned soil anchors upslope of the highway and a tied-back concrete tangent pile retaining wall for the roadway itself as well as reconstruction of the highway alignment, grade and drainage through the slide. Works were installed by top-down construction within defined time allowances stipulated in the contract. Significant engineering was undertaken beyond standard design processes for this complex project, such as comprehensive geotechnical investigations, aerial and terrestrial laser scanning and change detection analyses, pre-production test anchors, detailed geo-structural numerical modelling and due diligence activities to validate and optimize the design. The stabilization works have been very successful with the slide response being as predicted and the highway operating again as full two-lane service.

Oct 1, 2022

By M. D. Riegel, P. B. Pizzimenti, E. M. Zamiskie, Britain A. Materek

"The Skanska/Kiewit/ECCO III team (SKE) in association with HNTB was awarded the design-build contract for Phase I of the Kosciuszko Bridge Replacement Project. As lead designer for the SKE team, HNTB was responsible for the design of the Brooklyn Connector which includes construction of approximately 2000 feet of new staged earth-filled embankments utilizing prefabricated modular retaining walls (T-Walls®). The proposed embankments will be constructed adjacent to and beneath the existing Brooklyn Queens Expressway (BQE) viaduct while the existing viaduct remains in service. Critical aspects of the settlement assessment relating to the soils supporting the existing BQE will be addressed, as their behavior drives the deformation of the viaduct. Furthermore, a construction monitoring program was used to enable the designer to assess settlement predictions and allow SKE to mitigate potential impacts to the existing BQE during construction. Additionally, the methodology for installation of the embankments in a limited access area underneath an active viaduct supported on settlement sensitive shallow foundations will be presented.INTRODUCTIONSkanska-Kiewit-ECCO III Joint Venture, in association with HNTB was contracted by the New York State Department of Transportation (NYSDOT) to design and construct the Phase 1 replacement of the Kosciuszko Bridge Design-Build Project. Phase 1 of the project involves the design and construction of the new eastbound structures of Interstate 278 over Newtown Creek from Brooklyn to Queens. The project runs between Morgan Avenue in Brooklyn and the Long Island Expressway Interchange in Queens (approx. 1.1 miles) and includes the staged demolition of the existing structures."

Jan 1, 2016

By Michael Oakland

This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system.

By John Mould, Gordon Chen, Michael Oakland, William McElwee

"This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system. IntroductionThe Willis Avenue Bridge is one of the major access ways from the Bronx into Manhattan. The location is shown on Figure 1. The original bridge constructed in 1901 was a swing bridge over the East River. The bridge was in disrepair and outdated with regards to its ability to handle the flow of traffic resulting in numerousaccidents.In 2007, Kiewit Constructors Inc./Weeks Marine, Inc., A Joint Venture was selected to construct a replacement bridge. The $612 million project included construction of a new bridge just to the south of the original bridge. The most notable aspect of the construction was floating and lifting the new 350 ft. long swing span in place as a single piece. However, another significant challenge was using blasting to demolish two of the abandoned piers which were within the East River. The blast would be near existing structures in both Manhattan and Brooklyn and would be within 30 ft. of the new bridge."

Jan 1, 2017

By Bao K. Le, Khang T. Truong, Masaki Kitazume, Toru Kobayshi, Long P. Le, Tanaka Hitoshi, Makoto Kamimura, Hoang-Hung Tran-Nguyen

"Earth levees constructed using dredged materials taken from a river along an earth levee have annually damaged in the Mekong Delta due to high void spacing in earth levees and floodwater. Sliding and internal erosion due to floodwater or piping are two key factors causing earth levees’ failures. This study proposed to apply Deep Mixing Method (DMM) to reinforce earth levees in the Mekong Delta, Vietnam. The DMM creates a soil cement wall or soilcrete wall having better engineering properties such as higher strength and low hydraulic conductivity than those of the in-situ soils. The DMM can be applied to reinforce earth levees with limit additional materials that provinces in the Mekong Delta are difficult to supply. The study investigates capacity of the DMM to reinforce earth levees in the Mekong Delta, Vietnam against annual floods. Seepage and slope stability analyses under various conditions were performed with various scenarios of earth levee’s body. The analysis results indicate that the DMM can create a wall that cuts off piping across earth levee significantly and can improve stability against deep sliding due to rapid drawdown of the floodwater.INTRODUCTIONThe Mekong Delta produces agriculture products of 50% of the whole country even though the Mekong Delta has an agriculture area of 30% of the country (Wikipedia 2014). Rice is the main product for the domestic demand and export. This is the main reason why the local people want to cultivate rice 3 times per year to increase the total rice product for export. To do that, the local provinces have constructed earth levees surrounding each area of 100-200-hectare against annual floods to protect rice fields, and farmers can grow rice in the whole year. There are thousands of kilometers long earth levees in the Mekong Delta, and the local governments have spent millions of US dollars to repair and to maintain their earth levees yearly (reports of Dong Thap province 2012; 2014).Earth levees in the Mekong Delta have often failed in flood seasons (e.g., from August to December), especially in Dong Thap and An Giang provinces – the two provinces confronting directly the annual floods from the Mekong River when the floods reach the Vietnam land. The main failure of earth levees is piping, and then causing collapse of some section of an earth levee. An earth levee was usually constructed by piling up dredged materials along a river with minimum compaction. Subsequently, floodwater flows through connected void spacing and washes out soil particles in the body of an earth levee slowly to create piping. Annual wet-dry cycles make the top clay layer swelling and shrinking to form cracks that can store rainwater to trigger sliding (whitlow 2001; Ton That Vinh 2003)."

Jan 1, 2015

By Keithe J. Merl, Brendan FitzPatrick, Gregg Piazza

Urban and industrial construction projects commonly involve interior work within buildings, warehouses and manufacturing facilities. Renovations of these existing structures must address both structural and geotechnical engineering challenges while also balancing the practicality of implementing solutions within site constraints including limited site access, overhead clearance restrictions, vibration tolerances and uninterrupted facility operations. This paper highlights two projects for an international shipping company where mezzanine level additions within active shipping facilities required construction of new foundations. Construction requirements included low vibration levels, as well as rapid and clean installation to limit impacts on the active shipping operations. The selected system also needed to adjust to both variable ground conditions and differing overhead clearances. This paper describes the installation, design and performance of Ductile Iron Piles used to meet the project challenges. The low vibration, driven pile system offered the ability to work within restricted overhead environments while successfully delivering working compression capacities ranging from 45 to 75 tons (41 to 68 tonnes) as well as lateral and tension resistance. The paper also presents the results of site-specific load testing (and pile capacity) for various termination criteria. INTRODUCTION Urban and industrial construction projects commonly involve interior work within buildings, warehouses and manufacturing facilities. Renovations of these existing structures must address both structural and geotechnical engineering challenges associated with the new construction. Foundation solutions must also balance the need to achieve design requirements with the practicality to be installed within the particular site constraints including limited site access, overhead clearance restrictions, vibration tolerances and uninterrupted facility operations.

Jan 1, 2019

By Christian Hoyme, Jochen Maurer

Most of the current foundation projects are suffering from disconnected information silos. In the first silo there is the planning of the project with corresponding data, presented by paper or digital drawings. Here will Building Information Modeling (BIM) be one of the trends for the future. We will see more and more projects leaving the “old way” of 2D drawings and moving into 3D planning including metadata of the foundations. But even with a perfect BIM model of a jobsite, we are not at final end of digitalization. While execution of the project at the jobsite, a second data silo is evolving. Data collected directly from construction equipment and manual measurements is currently undervalued in most projects. Paper is passed to the equipment operator and major data from measurements on site are noted on paper and digitized afterwards. Automatically collected data is not be used to create site progress reports or similar report. So, the real “data” just flows around without connection to any other data already existing in projects. And then the third silo arises: The documentation of the project. Data collected on paper es reentered to create some basic documentation of the work handed over to the client. Spreadsheet software is still the “tool-to-be-used” to create at least some documentation. Finally, the documentation is not connected to the data created while planning and not connected to the automatically collected data from the jobsite. A connected jobsite in the foundation industry must link these information silos and have to create a full data-workflow from the design through the execution to the as-built documentation. INTRODUCTION Building information modelling (BIM) is currently the most popular term of construction business in Germany and probably all over the world. But as often there are many different definitions out there and everyone has his own definition or at least understanding what BIM is about. But for sure it is the most relevant for the construction industry in the near future. Most popular is the digital twin for the upper structure of a building. In most cases the BIM models just shows the building itself, but there is more to be implemented. For example: projects where a special foundation is needed, BIM should include also the foundation elements with meta data. There are several advantages. Not only the clash detection of anchors, but also the possibilities to check the interaction with neighbor constructions, power lines and so on are a use case. For sure most of the special foundation elements are not relevant for the whole lifecycle of a building. But during construction and later the demolition the information about the hidden elements is important and gives a benefit to all stakeholders. In the future there will be not the question: “What is already in the ground?”. The risk for following construction projects on the same ground will be minimized.

Jan 1, 2019

By Anburaj C., Srinivas A.

Deep excavation with support system is required to construct various part of underground structures like shafts, stations and entry structures etc. These structures have to be constructed using permanent or temporary embedded retaining walls with support system. The selection of a suitable type of retaining wall will depend upon the geological condition present in the particular location, time, cost and available equipment etc. In Bangalore Metro Rail Project, secant pile wall is adopted as the temporary earth retaining system and depth of excavation is about 20 m. It is designed initially based on bottom up construction methodology with 3 level of struts and 3 level of anchors but at later stage due to time and other construction related issues, it is decided to change the configuration to 6 levels of strut. Generally, in deep excavations, all the underground structures should be designed and checked for the critical forces from both permanent stage and construction stages. Since, secant piles are used as temporary retaining wall, only construction stage analysis is carried out to get the governing forces and deformation. In construction stage analysis, soil layers are defined with boundary conditions and the surcharge during construction and surcharge from actual building near the secant pile are considered. This paper discusses the effect of change in the support system from anchors to struts and how these changes in the support system affect the behavior of secant pile and subsequently adjacent buildings present in the influence zone of the excavation. As a result, in changing from anchors to struts, the wall displacement, strut forces and ground movement on the adjacent ground and buildings increases. The increase in deflection, ground movements and strut forces occurs during backfilling sequence of the underground station excavation. During backfilling, struts has to be removed and this imparts higher magnitude in deflection, strut forces and ground movements.

Nov 1, 2022

By Mike Muchard

A design phase load test program was performed at the Broadway Viaduct bridge site to evaluate load carrying capacity and constructability of post grouted drilled shafts. The program included construction, instrumentation, post grouting and load testing of three drilled shafts. Two shafts included sleeve port and plate base grouting apparatus and were post grouted. The third shaft was un-grouted and served as a control shaft for comparison of the un-grouted end bearing. The shafts were 5 feet in diameter with the control shaft at 55 feet in length and post grouted shafts at 55 and 66 feet. SPT borings at the centerline of each test shaft defined geotechnical conditions at each shaft. Test shafts were instrumented with strain gages and concrete integrity was evaluated with crosshole sonic logging. Instrumentation and data acquisition was used during the post grouting operation to fully capture the shaft behavior. Finally, Statnamic load testing was performed on all three shafts to their ultimate capacity. The fine to coarse sandy soils in which the shafts were tipped in were well suited to improvement from post grouting. Grout pressures of 660 psi were achieved with 0.08 inch or less of upward shaft movement. Subsequent Statnamic load tests showed 183 to 192 percent greater end bearing in the post grouted shafts as compared to the un-grouted shaft. The overall result showed a potential savings of approximately 9 feet to 35 feet of drilled shaft length in addition to the increased quality assurance from post grouting.

Jan 1, 2009

By Danny Winters, Wesley Schmutzler, Christopher Lewis, Matteo Bertoni

"SR 83/US 331 is a primary North/South roadway in Walton County that is a crucial link for tourism and commerce between the Walton County beaches and the heavily traveled I-10 corridor in the panhandle of Florida. The facility also serves as the primary hurricane evacuation route from southern Walton County. This 3.4 mile project involves expanding the current two-lane crossing of Choctawhatchee Bay to a fourlane facility to increase capacity and dramatically improve mobility within the corridor. One of the major goals of the project is to perform ground stabilization using Deep and Shallow Soil Mixing (DMM & SMM) along existing causeways. Ground stabilization is required due to the existence of moderately deep very loose soils that have settled considerably over the years. As a result, the Florida Department of Transportation (FDOT) incurred significant maintenance expenses and was unable to maintain an acceptable ride quality. FDOT considered soil mixing as one option to control this settlement. Quality Control for soil mixing relies heavily on the monitoring system used to control mixing parameters. This paper will examine in detail, the reporting of the Drilling Mate System (DMS) used to ensure the quality of each soil mixed element.INTRODUCTIONThe Florida Department of Transportation (FDOT) issued a Design-Build Maximum Price Request for Proposal (RFP) for the Choctawhatchee Bay Bridge expansion. The design-build (D/B) team of Skanska/Parsons Brinckerhoff was awarded the contract. The D/B team, in order to meet the unique deep ground improvement challenges of the Choctawhatchee Bay Bridge Project, selected Foundation & Geotechnical Engineering (FGE) as the engineer to design the ground improvement and TREVIICOS South (TIS) to execute the works.The FDOT in their RFP states that “either bridge or utilize a deep ground improvement method to stabilize the three segments of the existing earthen causeway” and “one possible method of deep ground improvement which is considered viable is deep soil mixing”. FGE developed a proposal to provide a unique rigid transfer platform to effectively stabilize the existing causeways. This platform (Fig. 1) consists of an upper 10 ft thick stabilized soil layer which transfers axial load to a series of deep columns. This robust system guarantees superior durability, ride quality and pavement condition and will exceed all required design and performance criteria including, “Less than 2 inches of settlement within a 1,000-foot section”."

Jan 1, 2017

By Mohamad H. Hussein

A minipile system was employed in underpinning a historical structure in Florida. The existing structure is founded on shallow foundations. Subsurface conditions at the project site consist of deep organic deposits interbedded with loose sand and silty sand. A minipile foundation system was deemed the most appropriate underpinning corrective measure for the already badly cracked structure. A total of 68 minipiles, 3.5 inch OD and 0.25 inch wall thickness closed-ended concrete-filled steel pipes, were installed to depths varying from 55 to 175 feet. Installation was accomplished with a pile driving hammer having a rated energy of 1 kip-ft. Highest required pile design load was 15 kips. Conventional static and wave equation analyses were performed to establish preliminary pile lengths, to assess pile drivability and establish driving resistance criteria. Dynamic pile testing using the Pile Driving Analyzer was conducted on six of the production piles. This paper describes geotechnical design considerations, installation procedures, and dynamic field monitoring. This case represents unique applications of pile dynamic testing and such slender, very long minipiles in compressible soils.

Jan 1, 1993

By Tiruvengala Padma, Nilesh Naik

Piles are common type of deep foundation elements used for the special bridges, transmission towers, Jetties, and tall structures. Lateral loads on the structures can be due to either earth pressures, wind, waves, impact, moving vehicles and eccentric application of axial loads or in combination of the loads. Hence the lateral capacity of piles plays a major role in determining the pile dimensions. The laterally loaded pile analysis is a soil-structure interaction problem as the lateral capacity of pile depends on the soil strength and stiffness parameters and its reaction to the lateral load on pile. The common approach to determine the lateral load analysis of piles is the Beam on Lateral Springs Method also known as “p-y” method. In this method the pile is modelled as a beam and supporting soil is modelled as lateral springs. This study is focused on the comparison of output obtained from three geotechnical softwares namely FB-MultiPier, L- Pile and Wallap. L-Pile Software is based on Finite Difference Method, Wallap on Horizontal Subgrade Modulus Method and FB MultiPier on Finite Element Method. Pile response in terms of deflection, shear force and bending moments under vertical and horizontal loads from above three software are compared and concluded.

Sep 1, 2022