Search Documents

By J. Reyher, R. Bratton, G. Luttrell, B. Li

"Flotation is regarded as the best available method of upgrading minerals and coal fines. However, its efficiency deteriorates rapidly with decreasing particle size. Further, ultrafine concentrates are difficult to be dewatered economically, forcing companies to discard part of the ultrafine materials to impoundments. To overcome these problems, a new method of separating and simultaneously dewatering ultrafine particles has been developed. Following extensive laboratory-scale test work, the process, known as hydrophobic-hydrophilic separation (HHS), has been tested successfully in continuous operations at proof-of-concept (POC)- and pilot-scale tests. The results show that the HHS process is capable of producing high quality clean coal with high recoveries and low moistures. INTRODUCTION Coal preparation plants are designed with up to four parallel processing circuits for treating coarse (> 12 mm), intermediate (12x1 mm) small (1x0.15 mm), and fine (<0.15 mm) particles. The plus 0.15 mm fractions can be effectively cleaned efficiently with gravity separation methods (Wills, 2006). At present, the only commercially viable option for cleaning the finest fraction is froth flotation (Yoon et al., 1999). In flotation, air is dispersed in the form of small air bubbles in a tank in which coal fines are suspended. The small air bubbles selectively collect the hydrophobic coal particles and float to the surface, forming a froth phase which overflows into a launder. As is well known, ultrafine coal particles of less than 30-50 µm are difficult to be collected by the air bubbles, resulting in low recoveries. Furthermore, fine particle flotation suffers from low carrying capacities and poor selectivity due to entrainment problems. (Bethell et al., 2005; Luttrell et al., 2014). In addition, the froth products containing ultrafine coal are difficult to dewater. Mechanical dewatering in general becomes inefficient with decreasing particle size due to small cake porosity and high surface area, resulting in high moistures (Hucko et al., 1988). The cost often becomes prohibitive with particles of smaller than ~45 µm (Bethell et al., 2005). Moreover, the high-moisture products are difficult to handle and incur high shipping costs and lower thermal efficiencies (Honaker et al., 2013)"

Jan 1, 2016

By R. D. Grove

The control of Florida phosphate flotation plants is largely based on the visual observations of experienced operators, both in recognizing good and bad froth conditions and in making judgments about the composition of feed, concentrate and tailing streams. Chemical analyses lag the process by at least two hours and therefore only assist in recalibrating the operators&apos; vision when major deviations occur. An image analysis system has been developed by IMC Fertilizer to improve upon the accuracy and precision of the composition estimation process. It still relies upon the operator taking a representative sample, but provides a measurement in about 15 minutes after that sample is obtained. This paper describes the system and its use and presents comparative results for various process streams.

Jan 1, 1993

By D. L. Kowal, P. J. Whittaker, M. A. Tuzun, N. O. Lotter

The area of flotation testing of drill-core is important in the business plan of most mining companies. Metallurgical information derived from this practice can be used to advantage in strategic decision-making. Sampling, flotation testing and subsequent Qem SCAN analysis of a mineral resource is one example of this approach. Anew resource, located in Sudbury, Ontario, is being assessed for the Sudbury Operations of Falconbridge Limited, which includes the Strathcona Mill. In this case, it was possible to improve the value of information from sampling and flotation testwork by using an improved, statistically-based test design, by sampling the resource by generic end-member ore type, and by integrating the Mineral Processing and Mineral Science disciplines into a Process Mineralogy team. In addition to producing standard metal grade and recovery information, this new approach provides more reproducible information from representative samples and flotation testing in a replicate format. Qem SCAN technology is used to produce a size by size mineral balance, including both modal percentages and liberation, from which flotation models for each ore type can be developed. As a result, a key understanding of the potential behaviour of a given ore type, if mined and then processed at the current mill operation, is gained at the 95%confidence level. The three ore types of this mineral resource were shown to have different flotation characteristics. Quantifying the mineralogy and liberation in each of the three ore types, has shown that this difference is due to changes in modal percentages of ferro-magnesium and magnesium silicate minerals such as pyroxene, talc and serpentine. Liberation across the three ore types is very similar and is therefore not responsible for variation in flotation performance.

Jan 1, 2003

By B. Pregerson, M. Gaft, J. Rabinowitz

The main phosphate minerals, apatite and francolite, are characterized by intensive selective photoluminescence, connected with impurities of Eu2+, Ce3+, V4+, Mn2+ and (UO22+ ). The non-uniform distribution of phosphate minerals in lumps makes photoluminescence sorting possible. As result, an intermediate product is recovered which is enriched by P205 and has relatively small amounts of chert, dolomite, calcite, fluorite, etc. In the case of Zin Phosphate Plant coarse rejects, for example, it is possible to separate a product enriched by francolite, practically free of chert and with a lowered calcite content. This material is suitable for flotation, with a potential 6-7 % increase yield of concentrate.

Jan 1, 1993

By Robert J. Guardia, James Rustvold, Robert A. Robinson, Christopher A. Robertson

In 1999, the Bonneville Power Administration (BPA) replaced approximately 730 m(2,400 ft) of damaged 42- and 36-inch concrete pipe by microtunneling Permalock pipe through sand and partly below groundwater. Microtunneling saved $3.5 to $5 million from the estimated cost of a shored excavation and avoided a railroad and contaminated valley fill. A slurry microtunnel boring machine (MTBM) was used for two segments where groundwater was present and a wheel excavator MTBM was used for one segment where groundwater was not present. This paper describes design and construction of this project that was completed within 2% of the bid and engineer’s estimate.

Jan 1, 2001

By M. K. Gangal, E. D. Dainty

The paper describes the capabilities of a micro-computer-based real time data acquisition system for monitoring and control of mine environments. Applications of such a system for monitoring the ventilation and air quality of a mine is outlined. The paper discusses the results of running a monitoring system with various environmental sensors in a simulated mine environment. The sensors used in this study are: carbon monoxide (CO), carbon dioxide (C02), nitric oxide (NO), nitrogen dioxide (NO2), sulphur dioxide (SO2 ), methane (CH4 ), air flow, absolute pressure, temperature and relative humidity. A performance evaluation of the monitoring system and sensors is presented.

Jan 1, 1987

By Michael Ferrell

The primary reason pigments are used in plastics is to impart a desired color to the plastic. Color is one of the more important assign considerations associated with today&apos;s market oriented society. Secondary reasons for adding pigments to plastics include: 1. Improved UV stability 2. Enhancement to selected physical properties 3. Changes in optical properties Pigments may be used at loadings as high as 20% or as low as .001%. Generally the loading levels are between 0.2% and 2.0%. Pigments may be added to the plastic either by the manufacturer of the plastic, or by the user of the plastic. If the customer buys material that is already colored, it is referred to as "pre-colored". If the customer buys uncolored plastic and adds colorants, the process is referred to as "in-house" coloring.

Jan 1, 1985

By Jon Kellar, William Cross, Eric Swanson, John Starkovich

Zirconium tungstate (ZrW2O8) is a unique material with a negative coefficient of thermal expansion. In order to fully utilize this material as a filler, a surface treatment needs to be developed to better improve the wetting and dispersion capabilities of the filler. This paper describes an initial study to characterize the filler as well as investigate fatty acid and silane surface treatments for eventual compounding with thermosetting matrices. It was found that ZrW20, has a point-of- zero charge between pH 2.7-3.0, and that both fatty acid and organofunctional silane treatments appear to be viable surface treatments for this unique filler.

Jan 1, 2003

By Chris Crowl

Employee involvement does not directly correlate to performance improvement. A key ingredient is the introduction of new Human Resource Systems that promote both performance improvement and employee involvement. Many organizations have tried to use employee involvement as the &apos;&apos;fixer" of performance issues-and seen their performance deteriorate further. They failed to realize that the entire human resource strategy must be connected to the goals of performance improvement and that greater employee involvement is only one tool in that strategy. So what are Human Resource Systems? These are systems that all managers use to get work done. Most of us are familiar with basics such as planning, assigning work, checking progress (auditing), completing assignments. We also commonly think in terms of staffing, training, compensation, or corrective action. All of these are human resource systems. All must be designed to support what you are trying to accomplish with your people. We call that the Human Resource Strategy. Let&apos;s examine one part of a total strategy intended to support more employee involvement at Kennecott Utah Copper-the hourly job structure. The design of hourly jobs directly affects how many employees of different capabilities are required to get the work done. It begins to answer some fundamental questions: • What are the roles and accountabilities of each employee? Do they have enough information to make decisions, to take responsibility for their work?

Jan 1, 2004

By Mustafa Kumral, Mehmet Balci

Strategic mine planning focuses on cutoff grade selection, capacity planning and block sequencing. Despite significant knowledge accumulated, potential value can be added to mineral sourcing by addressing various aspects. A case study on a metallic deposit with a lognormal grade distribution examines if grade/metal distribution influences cutoff grade selection. Six data sets with different shape and scale factors, but the same ore tonnage and metal quantity, are analyzed. Results indicate deposits with lower shape and scale factors are more sensitive to metal price and discount rate changes. The study also investigates the effect of economies of scale (EoS) on project value, focusing on the ratio of variable cost to total cost (capacity factor). Two regression analyses are conducted for optimal capacity planning and cutoff grade selection. The first shows capacity planning is highly sensitive to the EoS of mining and mineral-processing costs, with grade variability and metal distribution being negligible. In the second analysis, grade variability and EoS of mineral processing costs are vital for cutoff grade selection.

Sep 1, 2024

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined, so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits, but this process is subjective and results in quantities of dilution and ore loss that can be improved upon to enhance the profitability of mining operations. In this study, two weeks of production data from a homogeneous copper (Cu) porphyry and heterogeneous manto-type Cu deposit were used to assess the variability in the hand-drawn dig limits of 20 geologists, mining engineers and ore control specialists, which were compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine varied by 3.7 percent, from $10.5 million to $10.9 million, averaging at $10.8 million. The percentage was nearly double for the more heterogeneous mine at 5.9 percent, from $17.9 million to $19.0 million, averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9 percent increase) and $19.3 million (7.0 percent increase) for the homogeneous and heterogeneous deposit, respectively. The natural variability, diggability requirement and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Oct 1, 2024

By Min Chen, Qinghua Liang, Weishan Yan, Yuan Feng, Shigang Wang

Various coal mine robots (CMRs) and unmanned aerial vehicles (UAVs) are implemented to explore unknown mines for improving the safety and efficiency of mining. It is challenging for CMRs and UAVs to achieve accurate positioning due to the absence of the Global Positioning System (GPS), poor lighting conditions, and similar geometric features in complex mine scenes. LiDAR-based localization and mapping methods are more accurate than others, while long-time running in large-scale scenarios will introduce nonnegligible cumulative errors. This study presents a semantic-aided Li- DAR simultaneous localization and mapping (SLAM) with loop closure, which leverages the uniqueness of mine intersection structure to establish stable semantic loop closure. Specifically, we propose a semantic intersection descriptor of translation and rotation invariance, which encodes 3D point clouds of the same intersection from different positions and viewpoints into a unified image. By using the semantic descriptor, we can construct a constant loop constraint when the same intersection is revisited from different directions to reduce cumulative drift. We provide experimental validation using large data sets collected in two large underground mines, namely, a simulated Edgar mine deployed in ROS Gazebo and a public underground mine data set provided by ETH. Experimental results show that the proposed method has higher localization accuracy and outperforms the existing LiDAR-based SLAM strategies.

Feb 1, 2024

By Erhard M. Winkler

The rapid decay and disfiguring of stone monuments in urban and desert rural areas has challenged conservators to protect stone surfaces from premature decay. They attempt to halt the natural process of stone decay and possibly to restore the original strength lost mostly by chemical weathering and the loss of binding cement. Ageneral solution is not possible because the physical and chemical characteristics must be considered for different stone types. The failures of stone preservation and restoration are greater in number than the cures. The need for repair of stone decay goes back to evidence of Roman replacement of decaying stone. The presence of excess water in buildings has long been recognized. Moisture tends to enter masonry from air in humid climates, a most important but often underrated factor (Fig. 1) suggesting that sealing should be the answer. Undesirable staining and efflorescence result in accelerated scaling. Today, the great variety of chemicals available to the modem conservator for sealing. consolidating, or hardening stone fall into two very different categories: surface sealers and penetrating stone consolidants, or a combination of both. SEALERS Sealers develop a tight, impervious skin which prevents access of moisture. Surface sealing has saved monuments from decay by eliminating the access of atmospheric humidity. Pressure tends to develop behind the stone surface by moisture escape. Efflorescence, crystal growth action, and freezing can cause considerable spalling (Anderegg, 1949). Flaking results when moisture is trapped behind the sealed surface. Yellowing and blotchiness are also frequently observed. The following sealants are in common use today: linseed oil, paraffin, silicone, urethane, acrylate, and animal blood on stone and adobe. Extensive cracking and yellowing has resulted soon after application. In the past many such treatments have created more problems than cures: 1. Linseed oil and paraffin have been in use for centuries. Embrittlement and yellowing occur rapidly because these are readily attacked by solar ultraviolet radiation. 2. Animal blood as paint has temporarily waterproofed adobe mud and stone masonry. The origin of blood paint has a religious background rooted in the Phoenician and Hebrew cultures. Instant water soluble dried blood can substitute for fresh blood. Winkler (1956) described the history and technique of the use of blood. 3. Silicones have proven very effective and are long lasting. In contrast, acrylates, urethane, and styrene are generally rapidly attacked by UV radiation (Clark et al., 1975). Sealing of Different Rock Types Granitic rocks have a natural porosity traced to 4.5% contraction of quartz, during cooling of the parent magma, compared with only 2% contraction of all other minerals; protection against the hygric forces may require waterproofing of granite in some in- stances. The Egyptian granite obelisk in London is an example. Soon after its relocation from Egypt to London, Cleopatra&apos;s Needle was treated, in 1879, with a mixture of Damar resin and wax dissolved in clear petroleum spirit; surface scaling became evident after half a year of exposure to the humid London atmosphere. The treatment of the ancient granite monument from Egypt has denied access of high relative humidity (RH) in London to the trapped salts inherited from the Egyptian desert and has protected the monument from decay (Burgess and Schaffer, 1952). The sister obelisk set up in Central Park, New York City, has fared less favorably because similar treatment was done too late, only after the salts hydrated and hundreds of kilograms of scalings disfigured the obelisk surface (Winkler, 1980). Surface coating of other common stones may be needed. Crystalline marble absorbs moisture from high RH atmospheres: dilation may ensue when curtain panels bow as the moisture starts to expand during daily heating-cooling cycles. A good sealer may prevent the moisture influx provided that no moisture can enter from the inside of the building. Limestones, dolomites and all carbonate rocks are subject to dissolution attack by rainwater, especially in areas where acid rain prevails (Fig. 2). The interaction of sulfates in the atmosphere with the stone can be halted by waterproofing to avoid the formation of soft and more soluble gypsum. The stone surface attack can be diminished if nearly insoluble Ca-sulfite crusts can form, instead of Ca-sulfate. Replacement of fluorite or barium compounds at the stone surface acts as a hardener, rather than a sealant. Sandstones have generally high porosity and rapid water travel can occur along unexpected routes and from any direction. Any surface sealing may do more damage by scaling and bursting than if the stone is left without treatment. Sealing of sandstones is therefore not advised at any time. Testing the efficiency of sealants: Several authors discuss waterproofing materials, silicones, urethanes, acrylates and stearates, as to their water absorption, spreading rates of water on the treated surface, water vapor transmission, resistance to efflorescence, and general appearance (Clark et al., 1975). De Castro (1983) measured the angle of contact of a microdrop (0.004 cm3) on a stone surface as characteristic of the wettability. Laboratory tests and limited field performance are described by Heiman (1981). The crest of a Gothic sandstone arch, which was sealed with silicone,

Jan 1, 1994

By Zefang ChenLi, Laijun Ma, Lei Mao, Fang Lian

"In our work, the preparation technique of high pure manganese sulfate directly from low-grade rhodochrosite ore (MnCO3) was studied and improved intensively, including the effective leaching process and the short purifying process. Based on the same ion effect, the repeated leaching of rhodochrosite with sulfuric acid is proposed to improve the solubility of Mn2+ and inhibit the dissolution of the impurities Ca2+ and Mg2+. Moreover, the repeated leaching process could make full use of rhodochrosite and lower the dosage of sulfuric acidas raw material. With the aid of theoretical calculation, Ba(OH)2 was chose to adjust the pH value of manganese sulfate solution, and BaF2 to remove Ca2+ and Mg2+completely in the process of purifying. The results demonstrate that the extraction ratio and the recovery ratio of manganese reached 94.3% and 92.7%, respectively, which shows the prospect of industrial application. In manganese sulfate production, the heavy metal impurities have been decreased to less than 1ppm. Moreover, the content of calcium, magnesium and sodium has been decreased to less than 20ppm, which meets the standards of high pure reagent for energy and electronic materials. Our study enlightens an approach to the sustainable application of low-grade rhodochrosite.Introduction Low-grade manganese carbonate ores (=14%) becomes gradually the main resources for exploitation and applications in China according to national mineral resources survey (Tan et al 2004 and Singh et al 2017). Therefore, the electrolytic deposition technique of rhodochrosite faces great challenges including low electrolysis efficiency, high-resource input and high-pollution discharge (Fu et al 2010, Michelis et al 2009, Zhang et al 2013). Recently, more and more amount of manganese series with high or super high purity such as MnSO4, MnO2, Mn3O4 and MnO is demanded with the development of energy and electronic materials. Due to low-grade ores containing multiple elements such as iron, silicon, calcium and magnesium, conventional preparation of manganese sulphate with high purity from electrolytic product is characterized by long production-cycle and high-energy consumption (Subrat et al 2011, Mpho et al 2013). By contrast, hydrometallurgical method combined with thermal decomposition, hydrothermal synthesis and sol-gel processes has been widely studied because of its high efficiency, low consumption and low cost (Chen et al 2008). But the key problem in direct preparation of manganese series form low-grade rhodochrosite is to remove completely the multiple impurities such as iron, silicon, calcium and magnesium (Liu et al 2014). So it is urgent to develop a sustainable alternative approach with character of short process, high efficiency and environmental friendly."

Jan 1, 2017

By L. Reyes-Bozo, R. Ginocchio, A. Godoy-Faúndez, C. Sáez

Relationships among mining industry, society and environment have been historically complex due to its environmental impacts. In the Chilean mining industry, repetitive and small spills of fuel during maintenance of machinery have been adsorbed by desert soils and sawdust to control environmental pollution. The froth flotation is the main technology to recover specific mineralogical species from sulphide ores. Flotation reagents are expensive and representing an environmental risks due to its physics properties. Our objective was to investigate the feasibility of applying bioremediation as a cost-effective alternative technology to physical-chemical treatments and to evaluate the efficacy of biosolids as foaming agents. Our results show that the bioremediation is feasible by use of the autochthonous microbial communities and biosolids could be used as new environmental-friendly organic reagents. This research discloses a sustainable bioremediation process and industrial ecology model based on these two successful cases.

Jan 1, 2011

Potassic alteration domains of greenstone belt lode gold deposits are characterized by systematic partitioning between different groups of incompatible elements, such that Al, Ga, Th, U, Ti and V are decoupled from K, Rb, Ba, Cs and Tl. The former group of elements have concentrations and interelement ratios in alteration domains which reflect host rock control, implying approximately isochemical behaviour. In contrast, K, Rb, and Ba are strongly coenriched, and linearly correlated over th4ee orders of magnitude in abundance, where K/Rb = 260, and K/Ba = 40: K/Cs (-10 ) and K/T1 (-2x10 ) are also correlated, though more weakly. Lithium abundances, and Rb/Sr ratios are erratic in altered rocks. These interelement trends, collectively, are present in deposits variously hosted by ultramafic, mafic, or felsic volcanic rocks, and sediments or granitoids.

Jan 1, 1988

By Cary Hirner, Tony Cicchetti, Daniel G. Cressman, Jeff F. Wallace, Prapan Dave, Malcolm Sheehan

The City of Toronto is currently undertaking the design of the Black Creek Sanitary Trunk Sewer Relief Project. The Project involves the design and construction of approximately 20 kilometers of tunnel through shale rock of the Georgian Bay Formation and soft ground soil consisting of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits. The 20 kilometer alignment has been split into four sections of tunnel (1) the 12.9 km, 3.0 meter diameter Keele Trunk Relief Sewer, (2) the 2.9 km, 1.5 meter diameter Keele Trunk Relief Sewer Microtunnel, (3) the 3.9 km, 1.8 meter diameter Jane Relief Sewer, and (4) the 0.5 km,1.5 meter diameter Combined Sewer Overflow Storage Tunnel. Additionally, one 40,000 m3 wet weather flow (WWF) storage tank and numerous WWF connection shafts are to be constructed and connected to the Keele Trunk Relief Sewer to pick up WWF from existing outfalls currently discharging to Black Creek. The anticipated cost of the project is approximately $600 million with construction of the Project’s Phase One Works, the Keele Trunk Relief Sewer and Jane Relief Sewer, scheduled to commence in 2025. This paper provides an overview of the project in terms of the anticipated geotechnical conditions, the scheme developed for design and construction of the tunnel system and the associated schedule and procurement strategy. The consideration for planning of the tunnel system, the risk-based analysis and decision-making process are presented and form the basis for selection of a precast tunnel lining support method in the rock and soft ground.

Jun 13, 2023

By William W. Shriver

When the Henderson Project is completed in 1975, it will become one of the Free World&apos;s largest primary molybdenum producers. The Henderson Mine will be located approximately 50 miles west of Denver, Colorado, on the eastern slope of the Continental Divide. Ore reserves are currently estimated to be 303,000,000 tons with a grade of 0.49% MoS2. The mill and tailing area will be located approximately 14.5 miles from the mine in the Williams Fork Valley, which is on the western slope of the Continental Divide. Ore haulage from the mine to the mill will be by ten miles of underground railroad and 4.5 miles of surface railroad. The concentrator has been designed to mill 30,000 tons per day and will yield approximately 50,000,000 pounds of contained molybdenum per year. This paper is concerned with the tailing and water supply system for the Henderson Project and in particular the environmental considerations affecting their design.

Jan 1, 1970

By Scott Donald, Barry Esford

Cameco Corp. operates uranium mills and tailings management facilities at its Key Lake and Rabbit Lake operations in Northern Saskatchewan, Canada. Development at both mine sites began in the 1970s, with initial tailings deposition occurring within above-ground impoundments, which was common for these facilities at the time. As open pits became available at each site, and mining continued at other orebodies in the area, tailings management shifted to in-pit facilities to meet stakeholder expectations and improve the long-term security and environmental performance of tailings management at these facilities. The in-pit facility at Rabbit Lake (receiving tailings since 1984; Fig. 1), was one of the first (if not the first) engineered in-pit tailings facilities in the world and adopted a full pervious surround design concept with subaerial deposition. Under this concept, permeable sand and coarse rock are placed at the base of the pit, around its perimeter, as well as overlying the tailings at closure to promote regional groundwater flow bypassing the lower-permeability tailings. In contrast, at Key Lake, the in-pit facility (receiving tailings since 1996) adopted a partial pervious surround design concept. Under this concept, permeable materials were again placed at the base of the pit, and partway up the side walls; although for the upper portion of the tailings, the material is placed directly against the natural geologic materials. In the Key Lake case, the natural geologic environment provided the required bypassing of the tailings deposit to achieve the desired environmental performance while the base drain again facilitated pumping during operations to achieve consolidation objectives (Fig. 2). In both the initial design of the facilities, and through more than several decades of operation, it is clear that although in-pit tailings facilities provide common benefits with respect to long-term geotechnical stability, it is critical that their design approach take into consideration site-specific conditions

Jul 1, 2025

By Daniel H. White

Block caving, unlike most other conventional forms of mining relies principally on the natural forces within the rock mass to fragment and transport the ore. Obviously, not every orebody can be satisfactorily mined by block caving. In the early stages of mine planning an attempt should be made to assess the benefits of the block caving system relative to others, and develop a reasonable mining concept that may be used to provide preliminary information to mine planners and financial specialists. It is the intention of this paper to outline some basic geotechnical parameters that are essential to: 1) Assessing the feasibility of block caving an orebody and 2) Providing semidetailed information relative to mine design based on drill hole and other data.

Jan 1, 1979