Search Documents

By C. Y. Liu

This paper principally deals with the application of caisson foundation in the Chinese bridge building industry, the different types of caisson foundation adopted, and their spheres of application. Caisson foundation has been used and speedily developed for bridge works in New China, and a number of new innovations have been made in its design. Especially in deep water foundation, the Nanjing Bridge over Changjiang has attained one of the deepest bridge foundations in the world. There are six types of deep caisson foundation being now in use in China, namely:

Jan 1, 2010

By Brock Wallis, Steve Davidow

The following text will present the concept of rock socketed drilled shafts used to support electrical substation structures, and discuss the cost and schedule risks that traditional design responses to unforeseen shallow rock can pose to a project. Design considerations will be detailed, including rock characterization, shear strength of drilled shafts, and modeling lateral resistance of the shaft and surrounding rock. The specific case of drilled shafts installed for heavily loaded structures at the Moxie Freedom Substation will provide an example of how close collaboration between the engineer and contractor to refine designs based on site-specific feedback can provide tangible benefits to the project. In this example, value engineered designs resulted in an approximate 40% reduction in shaft/concrete volume and a 60% reduction in total rock socket depth. PROJECT OVERVIEW The Moxie Freedom Project included the construction of a new 500 kV switchyard in Berwick, Pennsylvania. The foundation contractor was selected to install both small and large diameter drilled shaft foundations to support the structures within the switchyard. The small diameter shafts were utilized to support transformers, switches, bus supports and a static mast, while the large diameter shafts were used to support one 180-foot monopole and six H-Frame structures. CHALLENGES: ROCK SOCKETED DRILLED SHAFTS Available geotechnical data at the time of bid included limited borings and seismic refraction. The borings were not located at every structure, and the contractor and design engineer were left to interpret desktop studies and geophysics to determine the probable site-specific conditions at each foundation. The data suggested substantial variability in the quality and depth to bedrock across the project area, indicating significant risk of deep embedment into bedrock at all seven large diameter shaft locations. Rock socketed drilled shafts pose unique challenges for both designers and contractors, and the topic has become a focus of national foundation organizations. Traditional design models result in deeper and/or larger diameter shafts where rock is encountered. In the case where site-specific geotechnical conditions are not clearly understood and rock is encountered at shallow depths, this can lead to significant additional rock drilling, impacting overall project cost and schedule. Rock drilling can result in more than ten times the cost of soil drilling and can easily take in excess of ten times longer to excavate.

Jan 1, 2018

By Liu Run, Jia Zhao-lin, Yan Shu-wang

"Piles with diameter larger than 2m in engineering can be defined as large diameter pile, and piles used for oil platform foundation in Bohai Gulf, are usually over 100m long and 2m in diameter. Such long piles have to be manufactured by segments before installation, because of transformation and hoisting difficulties. The segments of the pile are assembled by welding during installation one to another. Normally, assembling two pile segments takes one day or even a longer time, which mainly depends on construction conditions. After pile segment assembling, it proves to be difficult to restart the successive penetration. The mechanism of pile refusal is discussed and the process of driving a segmented pile is simulated with a finite element program. The calculating results show that, when the stick-up stability was satisfied, increasing the length of the last segment of the pile and assembling the pile segments when the pile tip penetrates into a clay layer could greatly ease the difficulty of driving the pile. Furthermore, cutting down the pile extension time is also one of the most effective measures to minimize the refusal risk.1. InstructionIn recent years, more and more oil platforms with six or eight legs have been adopted in Bohai Gulf, China. The leg piles with diameters of 2m or more have to be driven to about 100m below the sea bed. Such long piles have to be manufactured by segments before installation, because of transportation and hoisting difficulties. The segments of the pile will be assembled during installation, in which a successive segment will be attached to a formerly penetrated one by welding (Fig.1). The assembling work often takes one day or even a longer time."

Jan 1, 2014

By Y. C. Han

The advances in seismic design considering soil-structure interaction or soil-pile-structure interaction are described using a substructure approach. The nonlinearity of soil is considered approximately using a boundary zone model with non-reflective interface, and computer programs are available for practical applications. The validation of model is confirmed with dynamic tests on piles in the field, and the results for a single pile are used to compare with the predictions in this study. The liquefaction for sand soil layer can be accounted for, and a case of liquefaction is discussed. Two practical examples are examined, a vacuum tower structure supported on foundation of steel pile group and a table top structure supported on foundation of concrete pile group. To illustrate the effects of soil-pile-structure interaction on the seismic response of vacuum structure, different base conditions are considered, rigid base, i.e. no deformation of the foundation; linear soil-pile system; and nonlinear soil-pile system. The method introduced can be applied to the design of tall buildings, bridges, industrial structures and offshore platforms with soil-pile-structure interaction under seismic or dynamic loads.

Jan 1, 2010

By Paul M. Wiltcher

This paper discusses how benefits in engineering design can be achieved from combining existing GRP concrete design guidelines with carbon steel design codes primarily made possible due to the increase in the constitutive properties of modern composite rebar or GRP. It also examines the technical and practical considerations necessary to both construct and ensure the integrity of composite rebar during transportation and handling on site and the measures taken by Franki-Cementation Joint Venture to ensure the safe deployment of the GRP in the workplace on the Noord/Zuidlijn Project in Amsterdam between 2003 and 2006.

Jan 1, 2006

By Steven Dapp

A new hyperbolic model for generating P-Y curves is developed for use in lateral analyses of cemented soils (a ?C-F? soil with both cohesive intercept and friction angle), and includes degradation of the static loading soil response to model the effects of load cycling (repeated loading) with load cycle number. The p-y curves, for both static and cyclic loading, were derived from full-scale lateral test results conducted on a set of six drilled shafts in a loess deposit at the Kansas DOT test site. Values of the model parameters obtained from the load testing at this site are presented, as well as a discussion of the model parameters effect on the results such that the model may be rationally applied to other sites with C-F type soils. A step-by-step procedure is presented to illustrate the application of the model. Correlation of the model to the CPT cone tip resistance (qc) from CPT testing is made, as this was found to be the most reliable; However, the model is applicable to other methods, both in-situ and laboratory, of assessing the soils strength.

Jan 1, 2011

By J. -M. Rescoussier

Due to Important settlements inducing major structural damages, the western part of the Grand Littoral shopping centre has been closed in 1997. The present paper describes the project of underpinning including not only micropiles under the structure of the building but also a reinforcement of the soil located between the shopping centre and the edge of the embankment surrounding the western part of the shopping centre. The aim of this reinforcement is to reduce existing horizontal movements to allowable values.

Jan 1, 2002

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

By A. Garassino

A pile design was performed for a thermal power station in Egypt and more than 4000 piles were to be driven. Technical economical reasons suggested the choice of driven composite LACOR piles designed for very high specific loads. Some uncertainties on the behaviour of the pile soil system suggested to perform a test on an instrumented pile. Scope of the test was to verify the possibility of developping the required bearing capacity within the range of the allowable pile settlements values and the effect of the pile joint enlargement on that portion of skin friction to be developped by the upper pile section.

Jan 1, 1991

By Kodi Ranga Swamy, N. Sankar, M. Akhila

"Until recently, liquefaction-related studies concentrated on clean sands believing that only sands are susceptible to liquefaction. However, a few earthquakes like 1976 Tangshan earthquake, the 1989 Loma Prieta earthquake, the 1999 Kocaeli earthquake, the 2010 Chile earthquake, and the 2011 Christchurch earthquake, etc. showed that sand with fines could also liquefy. The research findings on liquefaction of silty soils are limited, and several structures constructed on such soil deposits are damaged during the past earthquakes. Some previous results of research on earthquake events show an increase of liquefaction resistance in silt soils with increase the fines content, but some report the opposite trend. This study presents the results based on undrained triaxial cyclic tests which were carried out on the fine sand with fines (0%, 10%, 20% and 40% fines). The samples were prepared at the required unit weight (Dr = 50%) and saturated by using back pressure and cell pressure increments. Each consolidated sample is subjected to cyclic loading with sinusoidal wave load form at a frequency of 1 Hz. The liquefaction resistance is evaluated in terms of cyclic stress ratio required to cause 100% pore pressure or 20% failure strain occur at 15 numbers of load cycles. Results are presented in forms of pore pressure build up and axial strain propagation plots. As the fines content increased, an increase in liquefaction potential was observed.INTRODUCTIONLiquefaction and related phenomenon have been responsible for tremendous amounts of damage all around the world. In general, the liquefaction may occur in fully saturated sands, silts and low plastic clays. When the saturated soil mass is subjected to seismic or dynamic loads, there is a sudden buildup of pore water within a short duration, and it could not dissipate which leads to reducing the effective shear strength of soil mass. In this state, the soil mass behaves like a liquid and causes large deformations, settlements, flow failures, etc. This phenomenon is called soil liquefaction. As a result, the ability of soil deposit to support the foundations of buildings, bridges, dams, etc. is reduced. Liquefiable soil also exerts a higher pressure on retaining walls.This lateral movement of soil could cause settlement of the retained soil. A sudden build-up of pore water pressure during quake also triggers landslides. Liquefaction damages of structures are commonly observed in low-lying areas near the rivers, lakes, and oceans."

Jan 1, 2017

By Derek Egan

"Abstract Construction clients want their foundation solutions to be right first time, every time; but it is often the geotechnical contractor who carries the most risk in achieving this. Robust validation to ensure that the installed geotechnical product is appropriate for the encountered ground conditions, will perform as required and be correctly measured for payment and record purposes is very important to minimise the contractor’s and the client’s risk. This paper outlines the development and operation of a robust real-time installation monitoring system which controls and validates the installation of driven cast in-situ (DCIS) piling. Using state of the art information technology the system allows the design engineer to interrogate the data acquired from the piling rig via his computer as the piles are completed. The use of the validation process, where data acquired during the driving of DCIS piles can be processed to estimate the finished pile performance, will be explained with reference to a new case study on large diameter DCIS piles. Examples of the routine use of the system will be presented to illustrate how automated monitoring of installation parameters can be used to raise the standard of reliability, efficiency and sustainability on piling projects. The conclusions to the paper will cover the key features and operational challenges characterising real-time monitoring of the execution of geotechnical works as developed from a number of years of experience of using a rig based data acquisition instrumentation system.INTRODUCTIONDriven Cast In-Situ (DCIS) piles have a long and successful history of use worldwide. The process, where a temporary steel drive tube, sealed at the bottom with a sacrificial base plate, is driven into the ground and filled with concrete before the tube is withdrawn, is well known (BS EN 12699, 2001 and Egan, 2013). Examples of large structures supported on DCIS piles installed by Keller UK include the Millennium Dome (now the O2 Arena) and the 2012 Olympic stadium in London.In recent times advances in piling rig instrumentation and telecommunications have enabled a new level of sophistication in the recording of installation parameters and the validation of pile performance. It is now possible to embed these features into the DCIS design and installation process which has improved the quality and efficiency of DCIS piling.This paper summarises the development and operation of a real time data acquisition and processing system for DCIS piling, but which is equally applicable to other forms of driven piling (for example concrete precast piling)."

Jan 1, 2014

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By Luca de Sanctis

The analysis of piled raft foundations in layered soils may be performed by 3D finite elements or by approximate procedures. Among the latter, the code NAPRA (Russo, 1998) is based on the method of the interaction factors and accounts for soil layering by the so called Steinbrenner approximation. A comparison between the results of 3D FEM and NAPRA for some reference layered soil profiles shows that the approximation is fully acceptable for engineering purposes, provided the stiffness of the single pile is properly selected. The interest of the conclusion lies in the fact that the amount of work needed to model a practical problem by NAPRA is but a fraction of that needed by FEM modelling.

Jan 1, 2002

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

Jan 1, 2002

By Gandhi

Piled raft foundation under uniformly distributed vertical loads has been analyzed using Finite Element Method. The soil is considered to be linear elastic, isotropic, homogeneous. The raft,pile and the soil have been idealized with eight noded brick elements. Parametric study have been carried out varying pile length, soil modulus, raft thickness, and pile spacing. Design charts have been produced to achieve 50% load sharing between pile and raft for optimum design. Data available in literature is compared with the design chart results and found satisfactory.

Jan 1, 1996

By Ricardo Dobry, Alain Pecker, George E. Leventis, Ralph B. Peck

"This year’s DFI Outstanding Project Award is for the design and construction of the foundation scheme for the largest cable-stayed bridge in the world. In 1993, Gefyra, SA (a French/Greek consortium led by VINCI of Paris, France) was awarded a €750 million ($1billion+ USD) Concession Contract to design, build, fi nance, operate and maintain a three-span cable-stayed suspension bridge connecting the Peloponnese, Greece’s southernmost peninsula, with the mainland across the Gulf of Corinth. The contract extends over a 42-year period, 7 years for design and construction and 35 years for operation. The project was fi nanced through a combination of public funds, private equity and bank loans. Alternative foundation concepts that were considered included traditional driven piles, deeply embedded caissons and soil improvement. PROJECT CHALLENGESThe extreme technical challenges faced included:??Weak foundation soils composed of soft alluvial deposits consisting of interbedded layers of granular and cohesive materials with thin layers and lenses of gravel and liquefi able sand pockets; rock is believed to be at a depth of 1,000 m (3,500 ft) or more.??A very deep seabed exceeding 60 m (200 ft).??The requirement to withstand the collision of 180,000-ton tankers traveling at 16 knots.??Maximum wind forces of 250 km/hour (155 mi/hour).??Design seismic forces corresponding to Richter magnitudes of 7.0+ with peak ground accelerations of 0.48 g at seabed.??Design tectonic movements of 2 m (7 ft) in any direction between any two adjacent bridge pier foundations/pylons.Considering subsurface conditions and local seismicity and water depths, foundation design and construction methods were the key drivers for this project. In large part, the success of the project is owed to the unprecedented partnering and collaboration between all partners involved fostered under the leadership of Jean Paul Teyssandier and Gilles De Maublanc of VINCI Group (France) who served as lead Concessionaire and General Contractor. The joint venture’s lead Greek partners were Elliniki Technodomiki/AKTOR and J&P/AVAX. Alain Pecker of Geodynamique et Structure (France) served as lead Geotechnical Consultant/ Designer while Buckland and Taylor (Canada) served as Design Checkers with Ralph Peck and Ricardo Dobry (U.S.) as Special Advisors on foundation issues, Langan International/Langan Engineering and Environmental Services P.C. (George E. Leventis, Gregory Biesiadecki and Diane Fiorelli) served as Technical Advisor on geotechnical, geodynamic and foundation/marine construction issues."

Jan 1, 2007

By Christian Besson

This article describes the implementation of a new jointing process for use between diaphragm wall panels. This process was initially introduced on the SOCATOP work site in uburban Paris (which involved the closing of the western section of the A86 bypass road), on a tunnel ventilation shaft. This brand new system upgrades the potential offered by other types of joints available and enables both ensuring the continuity of panels for structures over 40 m in depth under the strictest safety conditions and constructing shafts with diameters of less than 15 m. A patent for this process has recently been filed.

Jan 1, 2002

By Klaus Pöllath

The Netherlands RandstadRail project makes use of a large range of sophisticated geotechnical techniques to allow a shield driven tunnel to approach the central station of Rotterdam. This paper describes the construction of three deep excavation pits constructed with 1.2 m and 1.5 m thick diaphragm walls. Besides the presentation of the actual diaphragm wall activities special consideration is given to the break-in and break-out situations of the TBM into the deep excavations pits using sealing blocks and partly glass fibre reinforcement in the diaphragm walls.

Jan 1, 2006

By Amaneh E. Kenarsari

Among the different sources of uncertainty in pile bearing capacity prediction including inherent heterogeneity, measurement and model uncertainties, the inherent heterogeneity of soil properties is of particular interest and is considered in this study. Cone tip resistance data are utilized to calculate pile bearing capacity by considering vertical soil variability. In this regard, cone tip resistance component of CPT data is assumed as a random parameter. Realizations of this parameter are achieved with the aid of local average subdivisions and random field theories. Monte Carlo simulation is used to generate different realizations of CPT or CPT-u data. Pile bearing capacity was then calculated by the use of direct method. Pile bearing capacity are predicted for a project in south of Iran using this method and probability density function for the total bearing capacity of pile is plotted. Coefficient of variation of 33% for ultimate bearing capacity shows the variability of bearing capacity due to variation of soil strength in depth. Cumulative probability chart for the ultimate bearing capacity are plotted as an efficient tool for estimating ultimate bearing capacity of piles with different desired confidence levels for vertically variable soil strength properties. Significant difference between mean value of pile bearing capacity (18 MN) and limit with 95% confidence level (8 MN) emphasizes the importance of considering soil variability.

Jan 1, 2011