Search Documents

By \/eena Sahajwalla, Alexander Blagus

This paper reports the effect of using High Density Poly-Ethylene (HDPE)/coke blends on the reduction behaviour of Mn3O4 to MnO at 1000°C. The results suggest that CH4 release increases with increasing HDPE addition. The results show that the rapid release of methane, over only the initial five minutes, limited the interaction of Mn3O4/MnO with CH4. With the devolatilisation of HDPE there was increased porosity in samples containing HDPE, assumed to be the major factor in differences of reduction rates.

Jan 1, 2011

The 2-4D window shown above is the base startup window which allows you to begin a new project. ??Setting up the project is the first step ??The next step is to setup the properties to be used in this project

Feb 1, 2008

By H. C. M. Gordon

IN every co al mine the hazard of fire in the underground workings is always present. This is a natural condition, because the mineral wrought and the supports normally used are themselves combustible and because underground fires may originate in many ways. The main causes of such fires are: (1) Open lights igniting gas, wood, or the coal itself. (2) Explosives igniting gas or coal. (3) Spontaneous combustion. (4) Electric sparks or short circuits igniting gas, wood, or coal. (5) Frictional heat igniting wood, coal, or oily material. (6) Explosions of gas or coal dust igniting wood or coal. The relative importance of these causes, and others less frequently met with, varies from district to district and depends to a great extent on the equipment and supplies used, on the training and discipline maintained among the workmen, and on the liability of the coal to heat spontaneously. It follows, therefore, that open lights should not be used and that, wherever there is the least possibility of methane being encountered, only locked safety lamps of an approved type should be allowed underground. It follows, also, that only 'permitted' explosives should be used and that the it use should be confined to conditions under which they are ?permitted?. Similarly, electric equipment should be of an approved type and all such stationary equipment should be housed in well-ventilated fireproof rooms. Such rooms, as well as entries to stables and oil houses, should be provided with doors which can be easily and tightly closed and which should be constructed of fireproof material.

Jan 1, 1937

By Anita Marks

In 2007 Copper Mountain Mining determined that there were sufficient resources to consider reopening the Similco Mine near Princeton, BC. The mill facility that had been built by Newmont Mining in 1972 was closed in 1996 and all of the process equipment removed. The mill had been built on the west side of the Similkameen River to facilitate mining of the Ingerbelle Deposit. In 1980 construction was completed on a primary crusher and cable belt to deliver ore across the Similkameen River from the Copper Mountain deposit to the Ingerbelle mill. With the decision to restart mining of the Copper Mountain deposit, the decision was made to design and build a 35,000 tpd grinding and flotation mill near the mining operations. This paper discusses the application of historical operating data for the selection of the mills for the new grinding circuit and provides an overview of the grinding circuit design.

Jan 1, 2012

By W A. James

The use of spectrographic semi-quantitative analysis has recently been of considerable value in establishing the geological relationships in a complicated orebody. The principal minerals found in the Mount Pleasant orebody are cassiterite, stannite, sphalerite, molybdenite, wolframite, chalcopyrite and galena, associated with arsenopyrite, pyrite and fluorite. In addition to the large number of minerals, a further com-plication is the non-uniform distribution of the economic minerals, with one mineral being the only one present in major amounts in one area and another mineral being predominant in another area. At the same time, all minerals are present to a minor extent throughout the deposit. This heterogeneity made it advisable to analyse all exploration samples thoroughly. Analysis by conventional means would have resulted in prohibitive costs. By the use of emission spectroscopy, however, it was possible to obtain, quickly and relatively inexpensively, a reasonably comprehensive picture of the orebody un-der investigation.

Jan 1, 1963

By H. C. Rickaby

Introduction The township of Swayze, from which the Swayze gold area derives its name, is in the Sudbury mining division, approximately 150 miles northwest of Sudbury. The gold area may be regarded as situated at the southwest corner of a triangular area whose northeast and southeast corners are at Porcupine and Shiningtree, respectively, and whose sides are between 70 miles and 90 miles in length. On a geological map, it would be found that belts of Keewatin greenstones and sediments form the sides of this triangle, and that they surround a large granite mass. Prior to the summer of 1931 the Swayze corner of this triangle had probably been less prospected than the other parts and comparatively little was known of it from the standpoint of gold mining possibilities. The extensive belts of iron formation to the south and west of Swayze received some attention about the year 1909, and during the years 1927 and 1928 some prospecting was done in the townships of Greenlaw and Cunningham, south of Swayze, but chiefly for base-metals- copper, zinc, and lead. In the summer of 1931 a very promising discovery of gold-bearing quartz was made by J. G. and J. L. Kenty, working for the Brett-Trethewey Mines, Ltd., in association with Northern Canada Mining Corporation, and Northland Prospectors, Ltd., and this property, now known as the Kenty Gold Mines, Ltd., has been actively developed with very encouraging results. Following this discovery a6d during the summer of 1932 much prospecting took place in the area, as a result of which a number of other discoveries of gold were made, chiefly to the west of the original find. They are distributed over a wide area, which includes the townships of Rollo, Raney, Swayze, Denyes, Halcrow, and Greenlaw.

Jan 1, 1933

By Kenta Kusunose, Dadang Sundana, Ahmad Munib Fikry, Yosuke Unno

PT Smelting has operated the Mitsubishi Process in which feed materials are charged into the S- furnace through top lances using a pneumatic conveying system comprising 6 feeding tanks (S-Feeding Tanks). Each S-Feeding Tank was designed as a batch machine and had been operated in a batch mode so that feed materials are conveyed 70% of the operating time (conveying time). An S-Feeding Tank was revamped in August 2016 in order to attempt to achieve 100% conveying time during operation, aiming to reduce the furnace draft fluctuations and melt temperature fluctuations leading to reduced copper losses to slag and refractory wear on the sidewall in the melt zone. After two-year operation with some adjustments and modifications, it was concluded that the new system works as expected. During scheduled major shutdown in November 2018, the same modification was applied to all other 5 feeding tanks as the first one, while several modifications other than the S-Feeding system were also conducted for the purpose of expanding the capacity of the smelter. INTRODUCTION PT. Smelting (PTS) Gresik Copper Smelter and Refinery is located 30 kilometers north of the city of Surabaya, East Java major port. PT Smelting equity partners are Mitsubishi Materials with 60.5%, PT. Freeport Indonesia with 25%, Mitsubishi Corporation RtM Japan Ltd. with 9.5% and JX Nippon Mining and Metals corporation with 5.0%. PTS was established in February 1996 and started commercial operation of the Mitsubishi Process in 1999. The Mitsubishi Process is a unique technology which connects 3 stationary furnaces, namely the Smelting furnace (S-furnace), Slag-Cleaning furnace (CL-furnace) and Converting furnace (C-furnace) by covered launders. These features result in savings in manpower and energy, and make the process more environmentally friendly since there is no ladle transfer of melt. Figure 1 illustrates the outline of the Mitsubishi Process.

Jan 1, 2019

Since 2008 rapid advances have been made in technologies for the sensing and sorting of ores, particularly copper, and copper-related ores. Advances include significant increases in the sensitivity and throughput, specifically in the area of bulk sorting. Such advances were not possible without contemporaneous advances in the understanding of copper orebodies, in particular the understanding and quantification of the heterogeneity required within an orebody to support an effective sort, regardless of the technology deployed to do this. This paper covers fundamental knowledge in the characterization of orebodies and their ores for sorting; relationships between measures of heterogeneity and sorting response; the design of bulk sorting systems that can exploit this heterogeneity to add value to copper operations; and, a quantification of the value that can be generated from bulk sorting at a case study mine. INTRODUCTION Society currently puts increasing pressure on industries to move towards cleaner and more efficient means of production, and the mining industry is no exception. Mining additionally faces other factors increasing the pressure to be more efficient: high-grade and easily accessible reserves have become largely depleted, therefore the mined grade at operations across most commodities, including and in particular copper, is decreasing. Additionally, the grade of new discoveries in the sector continues to decrease (Schodde, 2011). Factor in the high capital cost of processing facilities and the low levels of efficiency of current grinding circuits, and the situation for such mines becomes dire. Sorting, by maximizing the amount of ore extracted while simultaneously reducing the waste content in ore delivered to downstream processes (whether simply transport and crushing, or more sophisticated circuits such as grinding and flotation or leaching) has long been of interest to mining operations and projects struggling with low margins (Bamber, 2012). However, until recently sorting technologies that are both cost effective and effective at such high throughputs have not been commercially available.

Jan 1, 2019

By Michel Aubertin

Les rejets miniers sont communément utilisés, depuis plus de 60 ans, comme matériau de remblayage des chantiers souterrains. Les roches stériles et les rejets de concentrateur sont employés comme remblais car ils sont disponibles sur les sites miniers à un coût réduit pour aider au support de terrain. Le remblayage des ouvertures est également avantageux car il permet de réduire la quantité de rejets entreposée en surface. Dans les mines souterraines, le remblai des chantiers doit aider à maintenir un espace de travail sécuritaire, tout en favorisant la récupération du minerai et le contrôle de la dilution. Il est alors essentiel d'évaluer précisément les pressions exercées par le remblai sur les murs et sur les barricades installées près de la base des chantiers. Dans cette présentation, des solutions existantes pour évaluer les pressions dans les chantiers sont brièvement revues. Les auteurs présentent ensuite des solutions analytiques récemment développées à cette fin, qui permettent de tenir compte du transfert des contraintes du remblai aux parois des chantiers et des galeries. Les solutions proposées, qui sont basées sur la théorie de l?effet d?arche, prennent en compte l'influence de la géométrie des ouvertures et de la position des barricades. La méthode de calcul permet aussi de calculer l?effet des pressions d?eau pour un remblai partiellement ou totalement submergé. Les solutions s'appliquent au cas d?un remblai récemment mis en place, alors que l?effet de la pression interstitielle ne peut pas être négligé, et aussi à plus long terme sous une condition drainée. Des résultats expérimentaux et des simulations numériques sont utilisés pour valider les équations proposées. Les résultats analytiques et numériques montrent notamment que la pression totale sur une barricade peut être grandement augmentée par la pression d?eau, tandis que la contrainte effective peut être réduite par les pressions interstielles (par rapport à la condition drainée ou sèche). On discutera aussi des implications pratiques de ces résultats pour l?application des remblais souterrains.

Nov 1, 2008

A pilot scale AG milling campaign was conducted at the AngloAmerican Platinum pilot plant in South Africa. Different blends of hard:soft (silicate:chromite) and coarse:fine particles in the AG mill fresh feed were tested. The effects of multi-component feed on the pilot scale autogenous grinding are presented in this paper, and can be used as a guideline for multi-component feed blends for AG milling. Preliminary modelling and simulation for the multi-component AG mill model are also included.

Jan 1, 2012

By Thom Sedun

No sector of the mining industry is more closely tied to local communities than aggregates. Noise, dust, traffic, visuals aesthetics and environmental impacts all fall under the purview of neighbours, local governments and nongovernment organizations. It is no surprise that aggregate operations may not be welcome neighbors in many communities. In British Columbia (BC), the regulatory environment for aggregate operations includes a local component of municipal bylaws and land use-planning in addition to the usual suite of federal and provincial statutes that apply to its sister mining sectors. Additionally, under common law aggregate extraction is not considered to be a land use subject to land use zoning, and some aggregate processing activities can be regulated by zoning. Often traversing multiple local government jurisdictions, aggregate producers find themselves negotiating not only local traffic, but also a mosaic of regulatory environments. There is an opportunity in this present situation to facilitate the application of current technology and practices in the mitigation of many community and environmental concerns associated with aggregate operations. Moving a bulk commodity is a volume-based business, and operators often don?t have time for matters that don?t directly or obviously affect the bottom line. Regulatory agencies often play multiple and complex roles with respect to their industry, not the least of which is the fiduciary role. Balancing how and when to assist an industry is often a difficult decision. For the aggregate industry in BC, the Ministry of Energy and Mines saw an opportunity to assist not only aggregate operators, but also regulatory agencies, local governments, and the general public. Through investing in the Aggregate Operators Best Management Practices Handbook (handbook) project, the Ministry of Energy and Mines (MEM) believes that it will realize a return of upheld community values, enhanced environmental protection, improved regulatory compliance, reduce disputes and a stronger provincial aggregate industry. It is the intent to publish the handbook electronically through the MEM website later this year.

May 1, 2002

By W. H. MacLean

The Matagami district lies directly west of Chibougamau on the north side of the Abi tibi greens tone belt. Ores at Matagami are volcanogenic massive sulphides and occur in the dominantly rhyolitic Watson Lake group surrounding the Bell River Igneous Complex. Rhyolites and basalts of this group, and basalts of the overlying Wabassee group in the central part of the district, are tholeiitic; calc-alkaline Wabassee rocks occur in the western part. Massive sulphides occur associated with rhyolite domes that can be delineated by paleotopographic and isopach mapping. They are mainly distal deposits that formed over an extended period of time while several volcanic units were being deposited,

Jan 1, 1984

By Jacek Paraszczak, Stefan Planeta

"RésuméDans la première partie de cet article on discute Ie contexte technico-économique de l'usage des foreuses à l'eau sur béquille dans des mines sud-africaines. Par la suite on présente les résultats d'une étude comparative du forage avec les foreuses à l'huile et à l'eau par rapport aux foreuses pneumatiques. La performance des foreuses est discutée sous les deux aspects: l'aspect technique concernant Ie taux de pénetration et la quantité d'eau rejetee dans les galeries et l'aspect de fa santé et sécurité au travail, et plus particuliérement, les niveaux de bruit et de vibrations ainsi que Ie brouillard de l'huile. On conclut par l'évaluation du potentiel de forage à I'aide des foreuses hydrauliques dans Ie contexte canadien.AbstractIn the first part of this paper the technical and economical aspects of water-powered drilling are discussed. This technology, originally employed in South Africa, received some interest from Canadian mine operators. In this context a comparative experimental study of pneumatic and hydraulic (oil- and water-powered) jackleg drills has been realized. The performance of the drills is compared and the results reviewed with regards to technical aspects (penetration rate, amount of water spilled) as well as health and safety considerations (noise and vibration level, presence of oil mist). The potential for application of hydraulic jackleg drill is discussed."

Jan 1, 1995

By T. Niedoba

Coal as an energetic raw material is characterized by many features that determine its quality. The data concerning coal are usually treated as independent values, despite the fact that this kind of approach is not always appropriate. In the paper the dependencies between sulfur contents and volatile components in coal and particle size and density were analyzed. The method of ordinary kriging is applied to experimental data to describe this relationship; this method can be used for particles of any size and density. An example of the application of this technique is presented for energetic coal Type 31, originating from one of the Polish hard coal mines in Upper Silesia. Results from ordinary kriging are in good agreement with experimental results. Similar analyses can be performed for other properties of coal material, such as ash content, Roga number, and moisture. On the basis of the data obtained by ordinary kriging, a more comprehensive multidimensional model is described, which can characterize certain deposits or strata from which the analyzed materials originate. This is superior to basing the model only on experimental data, which often is limited by size of the sample. The results obtained by ordinary kriging applied to various types of coal would allow more precise analysis of individual properties of the studied materials and increase the ability to determine significant differences between them. This method can be also applied to other types of mineral raw materials, such as copper ore.

Aug 1, 2013

Arguably the SMC Test® has become the most popular laboratory hardness test in the world with over 17,000 tests having been completed to date, covering over 650 different ore bodies. It is now routinely used in design, optimisation and orebody profiling projects. The test is unique in that from relatively small amounts of drill core it simultaneously provides parameters that are used in simulation modelling of AG/SAG and crushing circuits as well as work indices that are used in power-based equations for predicting the specific energies of AG/SAG/Crushing and HPGR circuits. The very large data base that has been accumulated has provided the opportunity to study the differences in variability from deposit to deposit. This paper describes and discusses the trends that have become apparent from the study of this data base. Recommendations for appropriate selection of sample numbers are also made which are based on these trends.

Jan 1, 2012

By Mari Yamamoto

Controlled thermolysis of gold(I) complex, [Au(C13H27COO)(PPh3)], at 180 °C for 5 h under an N2 atmosphere affords the new type of monodispersed spherical gold nanoparticles capped by myristate and a small amount of PPh3 ligands (average diameter 23±1.5 nm), in spite of no use of solvent, reducing agent and stabilizer. Much attention has been paid to the preparation and structure determination of transition metal nanoparticles, because of their widespread use in technological applications.1 In general, the chemical reduction of metal salts and organometallic complexes2 by the use of reducing agent is carried out to prepare gold nanoparticles. In some cases, a large amount of solvent and stabilizers such as surfactants,3 polymers4 and ligands5 are used to prevent agglomeration of particles and control the particle size. For instance, Brust et al. reported a two-phase reduction of AuCl4 - by NaBH4 in the presence of dodecanethiol as stabilizer to prepare gold nanoparticles.6 On the other hand, O?Brien et al. recently reported an one-phase preparation of gold nanoparticles by the reduction of AuCl4 - by NaBH4 in the mixture of tri-n-octylphosphine oxide and octadecylamine which act as both solvent and stabilizer, but this procedure also needs reducing agent.7

Oct 1, 2003

By Mahmood Alemrajabi, Ake Rasmuson, Kerstin Forsberg, Kivanc Korkmaz

"In the present study, the recovery of rare earth elements (REE) in the nitrophosphate process of fertilizer production is investigated. The apatite has been recovered from iron ore tailings by flotation. After digestion of apatite in concentrated nitric acid, Ca(NO3)2.4H2O is first separated by cooling crystallization and then the REEs are recovered by precipitation. Optimum conditions in these steps have been determined in a previous study. The precipitate mainly consists of CaHPO4.2H2O and REE phosphates.In the present study, selective dissolution and re-precipitation have been studied in order to obtain a precipitate that is more concentrated in REEs. The precipitate was selectively dissolved in nitric and phosphoric acid at different acidities (pH 6 to 0) with the liquid /solid ratio of 100 mL/g. It is shown that most of the CaHPO4.2H2O and other calcium containing compounds will be dissolved at pH 2 while the REE phosphates are not dissolved above a pH of approximately 2. Thus, by partial dissolution of the REE precipitate at pH 2.5 most of the solid calcium phosphates will be dissolved and the remaining solid phase, which is more concentrated in REEs, can be filtered off as a fairly concentrated REE solid mass and the liquor can be recycled back to recover more P nutrients. Alternatively, the REE enriched precipitate was dissolved completely in nitric acid and re-precipitated again by addition of ammonium hydroxide to pH 1.2. A chemical equilibrium software, MEDUSA (Puigdomenech, 2013) has been used to evaluate the experimental results and to estimate the optimum conditions for selectively dissolving the precipitate."

Jan 1, 2016

By H. Al-Kazzaz

The 2-mm butt joints of ZE41A-T5 sand castings were laser welded using 1.6 mm EZ33A-T5 filler wire and a continuous wave Nd:YAG system at a power of 4 kW, surface defocusing and various welding speeds, Compared with the base metal, the fusion zone showed significant grain refinement due to high cooling rate, No grain coarsening was observed in the heat affected zone (HAZ). The porosity area percentage and total solidification crack length in the fusion zone (FZ) were reduced as the welding speed increased from 4 to 7 m/min, Fusion zone area, total penetration depth, and weld width decreased with increased welding speed, The hardness in the FZ was similar to or higher than the base metal after a natural aging of about one year, but there was a drop in the hardness of the HAZ, The HAZ width decreased with increasing the welding speed, Tensile test showed that a joint efficiency of approximately 75 ? 90 % was obtained.

Jan 1, 2005

By P. Mpofu

In this work, the modification of interfacial chemistry of colloidally stable kaolinite clay dispersion has been carried out to improve its flocculation performance and dewatering behaviour. Synergistic action between dispersion pH, hydrolyzable metal ion and high molecular weight polymeric flocculant structure type (anionic polyacrylamide-acrylate copolymer (PAM) and non-ionic polyethylene oxide (PEO)) was found to play a pivotal role in inter-particle bridging, the enhancement of the settling rate and extent of consolidation of the pulps. Flocculation with PEO led to higher settlings rates in acidic than alkaline pH, whilst for PAM, the maximum dewatering rate was achieved in the neutral pH range 6 - 7.5. Upon shear, the PEO flocculated pulps showed dramatic improvement in consolidation to 40 wt%, the extent of which was greater at lower than high pH values. For PAM-based pulps were however, not shear-responsive, lower sediment solid contents of 15 - 23 wt% was observed between pH 3 and 11. Hydrolysable metal ions, Mn(II) and Ca(II), used respectively at pH 7.5 and 10.5 in conjunction with PAM and PEO, significantly enhanced the settling rates and consolidation of the pulps. The findings exemplify the strong links existing between pH-mediated particle surface chemistry. polymer structure-conformation, inter-particle bridging and dewaterability of kaolinite dispersions.

Jan 1, 2004

By Alain Grenier

To be more competitive, we have to try new mining techniques. A few of them are: extend honghole length increase drilling precision new type of primary opening (slot) use of CMS to extend stope length This paper will cover our trials, successes and failures and will cover a few real cases that occurred at the Doyon mine.

Oct 1, 2001