Search Documents

By B. Van den Bogaert, K. Binnemans, T. Van Gerven

Europium is one of the most critical rare-earth elements due to the limited supply of this element combined with a high demand for red lamp phosphors. Therefore, the recycling of europium from end-oflife lamp phosphors has become increasingly important. Photochemical reduction of europium(III) to europium(II) and subsequent removal from rare-earth mixtures by precipitation as EuSO4 is a very selective and efficient method to recover europium from binary europium/yttrium solutions. It is shown that full separation of europium and yttrium is feasible from laboratory prepared non-equimolar Eu/Y mixtures up to a ratio of 1/20, which reflect the composition of red lamp phosphors. Optimal conditions were determined at pH 4 with isopropanol as a radical scavenger, which is a less harmful and toxic compound than the commonly used formic acid scavenger. Europium removal efficiencies of more than 95% were achieved, with a purity of 98.5% of the EuSO4 precipitate. The irradiance of the used light source, expressed in mW/cm2, has a large impact on the illumination time needed to remove europium from the solution. It is observed that higher irradiance results in a shorter induction time, i.e. a period during which virtually no europium is removed, and a faster removal rate once the induction time has passed. The photochemical separation technique was applied to recover europium from leached industrial red lamp phosphor (YOX) powder, with a Eu/Y ratio of 1/30. Europium recovery of 50% was reached with a purity of 96%, proving the feasibility of this method for the recycling of europium from end-of-life lamp phosphors.

Jan 1, 2016

By Rashid Bashir

The presence of groundwater in the form of large aquifers can have an important influence on investment decisions for underground mines. The design for such mines requires development of special mining methods, and mine dewatering infrastructure to avoid hazards during shaft sinking and underground development. The costs associated with mine drainage control and Mine Dewatering Systems (MDS) are relatively small compared to the huge consequential losses that can occur in case of an uncontrolled inflow and subsequent flooding of the mine. The design of MDS needs consideration of accurate prediction of the maximum uncontrolled inflow rate, availability of the system during an uncontrolled inflow while the inflow is mitigated, and decision on pumping system technology to have capability to operate under water. The research presented in this paper provides a theoretical framework for a reliability based design procedure which takes into account the uncertainty in the estimate of the maximum uncontrolled inflow, performance of the system during the period of an uncontrolled inflow and a methodology to decide on appropriate pumping technology considering the reliability of the system and available underground storage. The reliability based mine design procedure integrates the ideas of Effective Reserve and Hydraulic Reliability Index to come up with a unified methodology for design of Mine Dewatering Systems.

Aug 1, 2010

By Michel Dagbert, Mohammed Harfi

"Abstract - The Draa Sfar polymetallic deposit, at about 16 km NW of Marrakech in Morocco, is a massive sulfide zone at the contact between an underlying volcanic and an overlying clastics sequence. The mineralized body is a flat lens with schistosity and "boudinage," tilted to the west and with a strong dip to the east. The lens extends over a strike length of about 2 km and from surface to a depth of about 1 km, with thickness varying from 1 m to almost 30 m. It has been intersected by about one hundred surface drill holes and, in its south part, by about thirty underground fan holes from two exploration levels at depths of 300 m and 400 m. On these two levels, the massive sulfide zone has been channel sampled over a cumulative length of about 0.7 km. Results from drill and channel samples are used to estimate the resources of the orebody according to several methods: sections, polygons around intercepts on a longitudinal plan, grids on the same longitudinal plan with various distance weighting methods including kriging and, finally, a 3D grid with the same range of interpolators. A comparison of the various estimates delineates the important factors in deriving resources for this type of deposit. Those factors are mostly geological and related to the interpretation of the geometry of the two limiting surfaces of the zone. For the 3D gridding, the authors have devised a new and original method that constrains the interpolation of blocks from samples to a geometry of limiting surfaces. The resulting model shows internal grade variations that parallel fluctuations of zone thickness and orientation without having to re-orientate the search window in each block. Résumé - Le gisement polymétallique de Draa Sfar, situé à environ 16 km au NW de Marrakech est un horizon de sulfure massif au contact d’une formation volcano-sédimentaire de base et d’une formation détritique sur-jacente. Le corps minéralisé se présente sous forme d’une méga-lentille aplatie, schistosée, boudinée et déversée vers l’ouest avec un fort pendage vers l’est s’étendant sur une longueur de 2 km et une profondeur de près de 1 km avec une épaisseur variant de moins d’un mètre à près de 30 m. Il a été reconnu par plus d’une centaine de sondages de surface et, dans sa partie sud, par une trentaine de trous souterrains en éventail à partir de deux niveaux à des profondeurs respectives de 300 m et 400 m. Sur ces mêmes niveaux, des traçages ont permis de rainurer le minerai sur une longueur cumulée de 0.7 km. Les données de sondage et de rainurage ont servi à estimer les ressources du gisement selon plusieurs méthodes : sections, polygones sur longitudinale, grille sur longitudinale avec différentes pondérations en fonction des distances incluant le krigeage et enfin grille tridimensionnelle avec le même éventail de pondérateurs. La comparaison des estimés obtenus permet de mettre en évidence les facteurs importants dans l’estimation des ressources de ce type de gisement. Ces facteurs sont essentiellement géologiques et relatifs à l’interprétation de la géométrie des limites des corps minéralisés. Pour l’estimation sur grille tridimensionnelle, on a mis au point une technique originale qui calque l’interpolation des blocs à partir des échantillons sur cette géométrie des surfaces de contact. Le modèle résultant montre des variations internes de teneurs qui épousent les fluctuations d’épaisseur et d’orientation de la zone sans qu’il soit nécessaire de ré-orienter les fenêtres de recherche dans chaque bloc."

Jan 1, 2002

By Pim van Geffen, Dave Lawie, James Cleverley

A growing problem facing geoscientists, metallurgists and process engineers is the lack of knowledge transfer between the exploration and production teams. This siloing is generally unintentional, as a typical project may change ownership several times over several decades before it reaches the feasibility and operation stages. Many exploration projects generate vast amounts of high-quality, quantitative data with great spatial resolution, but unfortunately these data are often ignored in subsequent deposit modelling. Instead, deposit models tend to rely on subjective, non-standardized, qualitative classification of geological materials (e.g. rock type, mineral abundance) and processes (e.g. alteration style and intensity), obtained through visual logging of drill core. When projects advance to feasibility studies, the required quantitative data are obtained through expensive metallurgical test work and detailed quantitative mineralogical analysis, such as QEMScan or qXRD. These detailed tests are generally only performed on a small number of large composite samples and the results are extrapolated throughout the deposit, inherently underrepresenting their true variability. Geochemical data obtained during all stages of the project provide comprehensive data coverage at much greater detail and spatial resolution, which allows for the estimation of key metallurgical performance parameters that are required for accurate deposit modelling and domaining.

Jan 1, 2015

By S. Rash Ahmadi

One of the most important elements in power plants is rotors and repairing the damaged rotors is very important in view point of economics. One of the most complicated problems in power plants is increasing of stiffness of the turbine rotors. This problem which occurs mainly due to thermal shock or rubbing makes to exit damaged rotor from service. These elements can be repaired effectively by heat treatment methods. Tempering heat treatment is the most common solution for straightening of damaged rotors but it requires having good knowledge about heat treatment parameters (temperature and time) and their affects on fundamental properties of rotors. In this article, a suitable method is introduced in order to modify the increased stiffness in journal part of rotors due to martensite transformation, using heat treatment tempering process.

Oct 1, 2011

By D. Lopez, D. L. Doerr, T. J. Drake

Automated scanning electron microscopy has been widely used in recent years for gold and other precious metals characterization. However, application of this technology is resource intensive and in most instances needs specialized technical personnel to process the samples and information. Newmont Metallurgical Services (NMS) has recently acquired an ASPEX SEM. The ASPEX SEM offers some significant benefits/improvements in sample preparation and sample processing time. NMS and ASPEX have been working together to develop an approach utilizing this technology for the minerals processing industry and specifically for gold characterization.

Jan 1, 2011

By Ali Montaser

This paper presents an experimental study conducted to facilitate the use of RFID on construction job sites. The study focuses on deployment settings to provide data acquisition with higher accuracy for indoor location sensing. It provides extension to the state-of-the-art in this field as it addresses the impact of metal media proximity to RFID tags, the reasonable duration for data capturing, number of RFID tags employed and the distance between them. Low cost passive RFID tags were used in the experiments where each tag is used as a reference point with a known location. Five hundred and forty (514) experiments were conducted in lab environment using a 3m by 3m test bed that is dynamically rearranged to generate 15 test beds and a total of 67713 data sets were collected and analyzed. The collected data were captured from nine locations for each test bed at four time intervals. Received Signal Strength Indicator (RSSI) was used as the main attribute for signal measurement to process the captured data. Results of the data analysis performed are studied under four main categories: duration, number of tags, locations of tags and metal interference. The best duration was found to be the 15 second in the test bed with the least number of tags; as the short amount of time to capture data did not allow creation of a lot of interference among the emitted signals. Within each test bed, errors occurred most at points where the received signals were not well distributed in a 360 degree vicinity of the data capturing point. It means that the center point of each test bed resulted in lowest errors and the points located on the extremities led to the highest errors. Finally, metal objects were found to have major impact on the accuracy of the captured data; to the level where reliable values for errors could not be calculated in the test beds attached to metal objects. In summary, the results of the experimental study and related findings are expected to provide guidelines to the users of RFID technology for localization in building construction.

Aug 1, 2013

By R. W. Thompkins

"PREFACEThis paper will be published in three parts. Part 1, in this issue, will cover the occurrence of uranium, radiation from uranium ores, the uranium series, radioactive theory, radioactive equilibrium and application to the radon series, the working level, the theory of emanation and diffusion, transport by thermal diffusion of radon emanating from porous rocks, and definitions.Part 2, to appear in the October issue, will deal with radiation theory applied to uranium ores, other radon migration factors , fact ors affecting the radon gas release rate, measurement of radon gas emanation rates, the tunnel concept, variation of emanation rate with grade, and estimating radioactivity from grade analysis.The series will conclude with Part 3, in the November issue, which will discuss the techniques for controlling radiation and give some example calculations.1.0. Occurrence of Uranium1.0.1. Uranium is widely distributed in nature. Sedimentary rocks contain less than igneous or metamorphic rock s and as the outer 10 miles of the earth's crust is composed of 95 per cent igneous and 5 per cent sedimentary rock, it has been estimated that about 1.3 x 1014 tons of uranium exist in the earth's crust.1.0.2. It is not surprising, therefore, that radiation has existed naturally in the ear h ever since the beginning of time. It is found in such places as:(1) non-uranium mines;(2) houses not close to or connected to uranium mines;(3) ground-water tables supplying drinking water to large populations.1.0.3. All mines do not necessarily have abnormal radiation in them, but it is possible for many mines to have abnormal levels of radiation. Therefore, all underground mining operations should be tested for radiation."

Jan 1, 1982

By N. Lecuyer

"During early 1980, pre-production work commenced at the ""Les Mines Gallen"" project, north of Noranda, Quebec. As a result of the acid mine water associated with this property, a major pre-production phase included the installation of a water treatment plant to render the water environmentally suitable.This paper emphasizes the planning, installation and operational factors of the treatment plant necessary to the success of the mining operations and the maintaining of a clean environment.Introduction,T he Gallen Project is a zinc, gold and silver open-pit mining operation approximately 10 kilometres north of Noranda, Quebec. This property has a long history, with initial diamond drilling done in the early 1930s and underground mining taking place between 1953 and 1962. This property was reactivated in 1980, with production scheduled a t a rate of 45,000 ton s per month.Included in the reactivation plans for the property was the installation of a water treatment plant to treat the acidic mine water.Plant DesignThe requirements for the Gallen water treatment plant were two-fold. Firstly, it was necessary to neutralize the acid water and secondly to produce a sludge containing metal hydroxides and sulphates which would be stable when stored, and a clarified overflow meeting governmental regulations to be discharged to the environment.The flow sheet (Fig. I) will explain the process in treatment of the acid water.Acid mine drainage is treated with lime to increase the pH to 9.50. Metals in solution are precipitated as metal hydroxides and the 504 as calcium sulphate. The precipitate slurry is then aerated to convert ferrous iron to ferric iron, which is more stable for storage and disposal.The precipitate is next flocculated with a polymer flocculant and settled in the thickener to produce a sulphate/Hydroxide sludge and a final effluent discharged to the environment."

Jan 1, 1983

By R. G. McDonald

"High iron solution concentrations often result in the formation of basic ferric sulfate during the high temperature oxidation of sulfidic materials such as base metal and refractory gold concentrates. Consequently, the “Hot Cure Process” followed by limestone neutralization is required to facilitate subsequent processing and/or disposal of the leach residue. The present paper discusses strategies that can be employed to influence the composition and nature of the high-iron content leach residues produced during pressure leaching.INTRODUCTION Control of iron deportment in hydrometallurgical processing remains a key challenge for a range of reasons. Strategies generally relate to the control of conditions under which iron is optimally rejected (Demopoulos, 2009). Supersaturation provides the driving force for crystallization and this can be controlled by a number of factors that include (1) pH and/or Eh control, (2) the presence of matrix anions and impurities, (3) dilution, (4) complexation and dissociation and (5) manipulation of the rate at which the metal to be precipitated is released to solution. Each of these factors is impacted by temperature. Good control of crystallization is essential to the control of precipitate properties such as the degree of crystallinity, stability, particle size and quality which covers both the extent of impurity uptake and suitability of the precipitate for waste disposal. The quality and properties of iron precipitates in turn can impact downstream processing. It is the aim of this paper to discuss the generation of iron-containing residues produced during the pressure oxidation of sulfidic ores and concentrates and how the nature of these can be controlled to potentially facilitate further processing. A brief overview of several related topics will now be given and include, where relevant, discussion of work undertaken in our laboratories. In addition, brief discussions of selected process options that enable good control of iron rejection will be provided."

Jan 1, 2016

By M. Ye. Shulgina, M. L. Bolotin, S. A. Prokopev, Ye. S. Prokopev

Iron ores concentration at Russia’s operations is carried out using conventional flow sheets. They comprise the two-four stage grinding followed by one-two stage magnetic separation. This results in the maximum recovery of magnetite to concentrate and the tailings generation. The final concentrate is generated only during the last stage of magnetic separation. Technologically, this flow sheet layout is not effective at recovering the liberated magnetite grains during grinding to the resulting concentrate. Advanced models of magnetic separators do not allow for the selective separation of the tailings and the portion of the resulting iron ore concentrate. Magnetic product which is the ore mixture of the liberated magnetite grains, high grade and low grade intergrowths is directed to the next grinding stage. In this case, regrinding of the liberated magnetite occurs. In addition, the performance of hydrocyclones during classification in closed grinding circuits is poor. Their classification efficiency does not provide the material separation in accordance with the size. In this case, simultaneous separation in accordance with the density occurs. The quartz particles with the size of 300 mm have similar velocity and trajectory like the particles of magnetite with the size of 60 mm. As a result, light and coarser intergrowths report to the overflow and free heavy magnetite grains report to underflow and return to regrinding (“the density effect”). This resulted in a significant increase of a mill circulating load, the decrease in the feed throughput and higher power consumption. In this connection, the development of iron ore concentrate stage recovery with the focus on gradual liberation of the intergrowths is getting much attention. Gravity concentration technique, particularly, spiral separation is effective at solving the problem of stage recovery not only the dump waste product but also high grade magnetite concentrates at the early concentration stages. This can be attributed to a significant difference in magnetite (4.9-5.2 g/cm3) and host minerals (quartz 2.7 g/cm3) densities, which is the principal during gravity concentration. The test work on concentration of various products samples from current operations (the mills discharges, concentrates from various stages of wet magnetic separation and cyclones underflows) was carried out. Spiral separators SV- 500 and ShV-500 manufactured by Spirit LLC were used for the test work. High grade iron ore concentrate (69.05% Fe) was generated during primary wet magnetic separation concentrate concentration using a spiral separator. During the concentration of mills discharges the content of iron in the resulting concentrates and middlings of wet magnetic separation II stage was 64.5% and 64.6%, respectively. The recovery of iron to the concentrates of spiral separation was 33.6-42.0%. The studies presented demonstrate that by using spiral separation for iron-bearing ores concentration, you can separate magnetite liberated grains at the early concentration stages, decrease their regrinding and circulating loads in grinding circuits. This process is able to improve the overall recovery and economics of iron ores concentration process.

Jan 1, 2016

By G. Binks

In 1997, the Zinifex Hobart Smelter ceased ocean disposal of jarosite and the flowsheet was converted to reject iron as paragoethite. This paper describes the evolution of the flowsheet since the changeover and considers future flowsheet developments. The major change to the flowsheet has been an increase in the silica content of the calcine resulting from treating increasing levels of Century concentrate. The high silica levels impacted on the paragoethite precipitation stage, causing a deterioration in the settling and filtration characteristics of the paragoethite and an increase in the contained zinc level. The implementation of a two stage neutral leach step has enabled the flowsheet to cope with the higher input silica levels. Future developments include an understanding of the form of the zinc in the paragoethite and options to lower the zinc level to improve the overall zinc recovery.

Jan 1, 2006

By K. Nagai

The Asian projects are now in their second terms after the five-year first terms. Ultrafined-grained steels were developed in lab-scale and/or in practical process. Basic approach has been performed to explore the evolution mechanisms of ultrafine-grained microstructures. There have been investigated two approaches to make the ultrafine grains: the "recrystallization route" and the transformation route. In the "recrystallization" route, heavy deformation at low temperature is necessary for the ultra-refinement. In the transformation route, making the high density of ferrite initiation sites in the deformed austenite, especially of the heavily compressed austenite structures, is essential for the ultra-refinement, and further hindering the ferrite growth is also inevitable to utilize the high initiation rate. Strength and toughness are dramatically improved by the ultra-refinement. Fatigue property is also excellent. The poor uniform elongation can be enhanced by the design of the second phase dispersion. At the same time the application has been also pursued from various viewpoints of engineering to take advantages of the ultrafine-grained steels. Bridge, ship, construction, automobile and other high strength parts are being attempted for the application.

Jan 1, 2004

By G. Morin, G. Marin, M. C. Parr, J. Carignan

"Investment casting offers many advantages for the near net shape production of complex geometries, however, molten titanium reacts with most of the refractories used in investment casting shelling systems, which leads to the formation of an oxygen contaminated surface layer. This layer, called alpha case, is 0.1 to 0.6 millimeters in thickness according to the casting section size and must be removed either by mechanical or chemical milling processes. Alpha case removal processes affect casting tolerances and may contaminate the part intended for medical applications (e.g. embedding of abrasive grit media in the alloy). A shelling system based on an yttria prime slurry has been developed and was found to almost suppress the mold metal reaction. Yttria is an expensive refractory, but slurry life was found acceptable for small castings using a closed container and flow coating process instead of conventional pattern dipping. Alpha case depth has been determined for Ti6Al4V by metallographic techniques and microhardness measurements on different step block casting cross sections. Alumina and yttria second prime stuccos were evaluated in this study. The shelling system minimizes finishing operations in the production of casting for medical applications.INTRODUCTIONTitanium investment castings have been in the commercial market since the beginning of the titanium era in the mid 50’s. Investment casting is a cost effective way to produce complex parts for medical, aerospace and chemical processes applications. Investment casting of titanium is difficult due to the high reactivity of titanium with air and refractories used for shell mold building especially for the face coat. Melting is done under vacuum and no shelling system has been proven effective to suppress the mold-metal reaction yet. The main issue with the mold-metal reaction is the formation of an oxygen enriched zone at the surface of the castings named alpha case (Frueh et al., 1997; Kim, 2002; Saha, 1986). The alpha case is brittle, reduce the fatigue life in service of the parts and must be removed by chemical milling.For industrial purposes, calcia partially stabilized zirconia based slurries have become widely used in titanium investment casting for primary coats due to a combination of limited metal shell reaction. Calcia stabilized zirconia slurries have an acceptable shelf life and offer an interesting production window. Our experience shows that a resulting alpha case depth is 280 micrometers for a casting section of 6.35 mm in thickness is typical with such a shelling system (Morin, 2013)."

Jan 1, 2016

By S. Huang, K. Xia

"During crushing, rock particle is subjected to complicated loading and the particle shape influences the fragmentation outcome. Thus, a highly controlled laboratory test is desired to establish the relation between the loading and the fragmentation parameters for better understanding the rock crushing mechanism. In this work, a split Hopkinson pressure bar system in combination with high speed cameras is utilized to carry out a dynamic ball compression test, in which the spherical rock sample is adopted to avoid the shape effect. Using the elasticity theory, the history of the axial symmetric tensile stress perpendicular to the diametrical direction along the loading axis is determined, from which the loading rate and the dynamic indirect tensile strength are calculated. With the aid of the moment-trap technique, the total energy absorbed by samples is accurately determined from the one-dimensional wave analysis. Furthermore by considering the kinetic energy of the sample fragments using the high speed camera snapshots, the surface energy is determined for each sample. The relations between the loading rate and the fragmentation parameters, i.e., the number of fragments and the surface energy are established. The application of this method to a granitic rock shows that it is flexible and can be applied to the crushing study of generic brittle solids. INTRODUCTIONCrushers are widely used to break rocks to extract specific minerals in the mining industry, and to obtain rock fragments with desired size distribution in construction industry. During crushing, the breakage of particles can be in either the single-layer mode or the multi-layer mode. In the single-layer mode, the particle breakage can be assumed to be isolated, in which the interaction between particles can be ignored. It is thus suggested by many researchers that highly controlled single particle test should be performed to establish the relation between the input mechanical energy and size reduction for better understanding the crushing mechanism (Yashima et al., 1987; Tavares, 2007; Pitchumani et al., 2004)."

Jan 1, 2015

By J F. Short

The jet piercing process, developed by Union Carbide Canada Ltd., is well established in blasthole production in open-pit mining. By this process, holes can be drilled, shaped and chambered for blasting. In suitable ore or rock formations, a considerable cost reduction can be achieved. This paper reviews the equipment used, relates how cost savings may be accomplished, and concludes with a mention of the most recent developments in this field. JET piercing and chambering, a process for blasthole production in open-pit mining, leads, in many instances, to improved drilling and blasting techniques and costs. It is a method of working rock with a supersonic flame and, to be most effective, depends upon a characteristic of the rock called spallability. Spalling, in this case, is the breaking away of surface particles from the rock body due to stresses caused by the thermal shock of the jet flame. Various rock properties contribute to this action, but, in general, the harder the rock the greater the spallability and the more effective and economical is the jet process. The jet process has the capability to drill, ream, shape and chamber holes for blasting.

Jan 1, 1965

By A. Desbiens, M. Maldonado, R. del Villar, Aguilera. R.

This work details the application of a multiple model approach to estimate frother concentration in flotation processes. The methodology consists of identifying a set of linear dynamic models representing the effect of gas rate on the collection-zone gas holdup at different known frother concentrations (calibration step). An adaptive law is then obtained using Bayes' rule to evaluate the conditional probability that each model represents the observed system behavior. In this way, a frother concentration estimate is calculated as a weighted sum of model probabilities and their associated (known) frother concentrations. Experimental results conducted in a two-phase system using Dowfroth250C are promising. Modeling and analysis for MIBC frother are also provided.

Jan 1, 2009

By C. Hu

A MOS capacitor hydrogen sensor array is reported for hydrogen gas distribution mapping. Si(100) was used as substrate for film deposition. After silicon oxide growing on the silicon surface with dry thermal oxidation, palladium film was sputtered on silicon oxide as hydrogen-sensitive gate material in MOS structure. The 3x3 sensor array was patterned on silicon substrate and packaged in one chip. Sensors' response was test with impedance analyzer. The sensors in array were calibrated in the hydrogen concentration range from 10ppm to 10000ppm. The 2D hydrogen concentration distribution was obtained with the calibrated sensor array.

Jan 1, 2005

By G. D. Garland

The influence of natural electric currents, induced in the earth by changes in the earth's magnetic field, on the electric logging of boreholes has not always been recognized. Measurements made with fixed electrodes of changes in the vertical potential gradient in a hole near Calmar, Alberta, have indicated the effect of earth currents related to magnetic disturbances. It is found that appreciable errors in self-potential logging could arise during periods of magnetic storms, but the precise pat-tern of disturbance in any area seems to depend on the local structural conditions. As the amplitude of the natural earth currents increases toward the auroral zone, it is suggested that periods of magnetic disturbance be avoided, if possible, when electric logs are taken in the northern part of the western sedimentary basin. NATURAL electrical currents flow continuously near the surface of the earth, apparently as a result of electromagnetic induction

Jan 1, 1962

By M. Maldonado, P. Olivares

"A submersible sensor for real-time gas holdup measurement in the collection zone of industrial flotation machines is introduced. The working principle is based on the generation and measurement of a pulp flow using a gas-exclusion cell immersed in the aerated slurry. The gas exclusion cell consists of a variable-area open vertical tube designed to be filled only with pulp by preventing gas bubbles entrance. The higher density of the fluid column within the cell generates a downward flow of pulp; the rate of this flow is proportional to the gas holdup outside the cell. The gas holdup measurement is achieved by tracking the velocity of the pulp flow leaving the gas-exclusion cell, using a magnetic flowmeter. Construction details of a prototype and its testing in two- and three-phases are discussed.INTRODUCTIONFlotation process optimization consists of finding and maintaining operating conditions that maximize flotation performance measured in terms of recovery and grade. The selective separation of mineral particles proceeds in two interactive zones where different and simultaneous phenomena take place: in the collection zone, the valuable particles are separated by collection on the surface of bubbles, while in the froth zone, the bubble-particle aggregates are gathered, drained to remove entrained particles, and taken into the concentrate stream. The cell overall performance, which can be determined from proper stream sampling, is a function of the recoveries in the individual zones. These zone recoveries cannot be independently measured nor calculated from operating variables. Progress in the assessment of these recoveries has been slow because on-line and reliable sensors to measure properties of the drastically different dispersions existing in both zones are not available.In the case of the collection zone, it has been demonstrated that the recovery of hydrophobic particles on the surface of bubbles, considered as a process with first-order kinetics, correlates with the bubble surface area flux (Finch et al., 2000; Hernandez, et al., 2003; Lopez-Saucedo et al., 2012). Bubble surface area flux (bubble area generated per unit time and cell cross-sectional area), is a variable affected by gas flow rate, bubble size distribution, and frother type and concentration. Gas holdup (volumetric fraction of gas dispersed in the slurry) is also affected by the same variables, and as such, carries information on the interacting variables that define the performance of the process. Therefore, a correlation between gas holdup and bubble surface area flux was expected and demonstrated (Finch et al, 2000), and since gas holdup is easier to measure as no bubble size is required, it has the potential to be the basis of a cell control and optimization strategy if a continuous sensor is available."

Jan 1, 2016