Search Documents

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Hara Prasanna Mishra

"In the Sukinda Valley of Orissa, India, the total quantity of nickel ore reserves comprising of both lateritic and chromite over burden(COB) have been estimated at around 231 million tonnes containing 0.3 to 0.9% Ni. While mining of one tonne of Chromite ore, around 6-7 tonnes of chromite over burden are removed. These overburden materials are disposed as waste materials, which causes lot of environmental hazards and ecological imbalance. India imports a large amount of nickel and ferro-nickel to meet its growing demands in various sectors. For import substitutions, efforts have been made to produced ferro-nickel from the lean deposits of nickel bearing lateritic ores/ chromite over burden materials by reduction roasting followed by magnetic separation and then the nickel rich magnetic fraction is smelted to produce ferro-nickel. It has been possible to produce ferro-nickel of grade varying from 4-25% nickel.IntroductionDuring mining of chromite ore, large quantities of overburden materials are being generated. The materials amount to approximately 10 million tones per year contain around 0.3-0.9% Ni, 0.02-0.06% Co, 20-50% Fe and 4-9% Cr2O3 depending upon the location and the depth of the mine. These materials presently do not find any application for the extraction of nickel due to lack of a suitable technology. The materials are also unsuitable for ferro-nickel making because of their very high iron to nickel ratio. The country is seriously looking for a suitable technology to utilize these resources as its entire domestic requirements of nickel is met though imports. In this connection, a systematic approach has been made at the Institute of Minerals and Materials Technology, Bhubaneswar to develop a process for ferro-nickel making from this indigenous resource."

Jan 1, 2011

By Min Chen, Lei Xu

Sintering behavior and performance of high alumina refractory based on the ternary subsystem MgAl2O4-CaAl4O7-CaAl12O19 were investigated using ZrO2 as an additive up to 8 wt.% by solid state reaction sintering. It was found that the added ZrO2 could dissolve in the CA6 grains in the form of a solid solution, which enhanced the isotropic growth of CA6 grains and then improved the sintering. As a result, the densification process was improved and areas with enrichment of ZrO2 showed a more compact structure. With further increase of ZrO2 addition, tetragonal ZrO2 were found to locate in the grain boundaries for exceeding the solid solubility limit, which enhanced the thermal shock resistance, indicating that addition of ZrO2 exhibited a positive effect on sintering behavior and performance of this refractory. In addition, it is considered that the optimal amount of ZrO2 addition was about 4% considering the performance together with the cost.

Jan 1, 2015

By Suresh Sundarraj

A diffusion mass transport model for predicting the microsegregation in a solidifying and coarsening dendritic mushy region of a binary alloy is presented. Two versions of this model are tested; one based on expressing the solute concentration in terms of mole fraction and the other on expressing the solute concentration in terms of mass fraction. On comparing previous model data sets and conditions, used in the analysis of Aluminum-Copper systems, a number of inconsistencies emerge. These inconsistencies are resolved on identifying a single set of data and conditions which take account of compositional density changes, "non-linear" thermodynamics and dynamic coarsening. An additional investigation is carried out to study the effect of assumed cooling mechanisms.

Jan 1, 1992

By R. E. Sundell, S. M. Correa

"A mathematical model is developed for the fluid flow in tungsten-inert gas weld pools. The fluid is taken to be incompressible, viscous, electrically conducting, and confined within a pool of specified shape. The flow is driven by surface-tension gradient (thermocapillary), electromagnetic, and buoyancy forces generally in this order of importance. Analysis indicates that the electromagnetic field may be calculated a priori and so decoupled from the nonlinear fluid mechanics and heat-transfer problem. The resulting set of equations is solved numerically by a line relaxation process. Computational errors caused by truncation in finite-difference schemes and by inadequate grid distributions are considered. The model is used to study several cases of differing heat and current input to the pool with and without surfactant-induced thermocapillary forces. The principal conclusions are that the thermocapillary flow, when present, is dominant with surface velocities on the order of 1 m/s. The heat transfer, as deduced from isotherms within the pool, is crucially dependent on the flow. Also, flow velocities and weld-pool surface temperatures were measuredand agree well with the model.2. IntroductionThe requirements of improved control and of automation in the TIG (tungsten-inert gas) welding process have led to the development of mathematical models for the heat transfer to the workpiece. It is now widely recognized that the fluid flow in weld pools sufficiently distorts the conduction heat transfer pattern to warrant inclusion in a process model. The experiments of Woods and Milner (1), among others, demonstrated that TIG weld pools could be driven by the electromagnetic J x B body forces present, J being the current distribution and B the induced magnetic field. Atthey (2) calculated that in typical pools the buoyancy force was about an order of magnitude less important - despite the large temperature gradients present - and neglected it in a computational study of the magnetohydrodynamic (MHD) flow. This work also reviewed many earlier studies of MHD flow caused by a source of current at a fluid surface, including analytical studies by Shercliffe (3), Sozou (4), and Sozou and Pickering (5), and a numerical study by Andrews and Craine (6). These works establish the importance of the electromagnetic force in the weld-pool flow."

Jan 1, 1986

By V. M. Lsoitko

Statistical methods of technological mineralogy are used to model processing flowsheets in order to improve ore dressing efficiencies. The procedure involves determining geological and mineralogical characteristics of ores, classifying ore types and metallurgical procedures, and developing computer programs to interpret essential mineralogical parameters from on-stream analysis data. The on-stream analysis data include magnetism, radioactivity, luminescence and assays. The data are interpreted by computer and appropriate adjustments are made automatically in the plant.

Jan 1, 1989

By Akira Yazawa

The similarities and differences in copper, nickel and lead smelting processes are discussed based on the sulfur-oxygen chemical potential diagrams and the free energy minimization assessments using a thermodynamic software. The prominent features of copper smelting are ascribable to the fact that copper has a strong affinity for sulfur but weak for oxygen and the liquid phase immiscibility between Cu and Cu2S. During the oxidation of sulfides, nickel metal is not stable except at temperatures higher than 1500°C, well miscible with its sulfide, and is oxidized more easily than copper. Metallic lead looks as stable as copper during the oxidation of the concentrate but Pb and PbS. are much more miscible with each other and the vaporization loss is considerable. In the reductive smelting of oxides, the effects of oxygen potential and temperature on the copper contents in slag are not significant due to the monovalent character of copper and the reduction of copper content in slag is not easy in practice. The effect of the slag compositions on the oxidic metal contents of slag is much more significant for lead than either copper or nickel. Due to the immiscible nature between Pb and Fe, high grade lead bullion is easily obtained and lead is more tolerant to impurities.

Jan 1, 1998

By Lauri Holappa

Copper converting is mostly performed in Peirce-Smith converters. The process is still very similar to the original one developed in the early 20th century. It is a batch process in a horizontal cylindrical reactor with air blowing via tuyeres along the length of the reactor side. The Peirce-Smith converter has its roots in Bessemer's inventions in the 1850's as he tested both horizontal and vertical vessels for steel converting. However, for steel making a vertical pear-shaped converter with air bottom-blowing was established. In the course of time, there was a distinct necessity for oxygen usage instead of air due to harmful effects of nitrogen to steel properties and its cooling effect. In-bath blowing of oxygen did not succeed, however, and top-blown oxygen converter with oxygen lance (LD or BOF) was first developed in he 1950's and emerged rapidly to a dominating position. Somewhat later oxygen bottom-blowing via special shrouded tuyeres was developed (OBM or Q-BOP) but has attained only fractional share. Bottom-blowing technique had, however, impact on the current combined blown converters which adopted the benefits of both top and bottom blowing. In copper converting Peirce-Smith type converters have kept their position until today although new processes have been introduced and at least few of them seem to be emerging. In one respect copper converting has a clear leading position i.e. in the progress of continuous converting processes (Mitsubishi, Ausmelt). These processes utilise top-blowing lances instead of in-bath blowing tuyeres. A different principle for continuous converting is flash converting by Kennecott Outokumpu, which makes smelting and converting independent of each others. Solid ground matte is used as a feed for flash converting in a reactor shaft similar to Outokumpu matte flash smelting. A comparable process has been presented by Inco too. The paper discusses principal physico-chemical and process technical similarities and differences in copper and steel converting. Although these processes are metallurgically quite different it seems that during the modem history of ferrous and non-ferrous metallurgy, starting from the 1850's, the exchange of knowledge between these disciplines has been quite intensive. In long-term perspective, many similarities in the development can be found but also divergences due to different ambient circumstances.

Jan 1, 2003

By D. J. Murdock

Cominco Ltd. has developed a number of innovative technologies for electrowinning. The paper discusses the application of these technologies to the copper industry. Tankhouse and cell design will be discussed in addition to anode cleaning and cathode handling. Specific examples of the application of this technology to the copper industry are cited.

Jan 1, 1987

By P. A. Metz

The Fairbanks mining district has produced in excess of 7.5 million troy ounces of placer gold and 250,000 troy ounces of lode gold since gold was discovered in the area in 1902. The Fairbanks mining district is in the northwestern part of the Yukon-Tanana Upland Schist Terrane, an area of approximately 240,000 square km that has produced in excess of 21 million troy ounces of placer gold. All lode gold production from the terrane has been from the Fairbanks mining district, and all of this production has come from high-grade gold-quartz polymetallic sulfide veins. Gold grains in the vein systems range in size from several microns to several millimeters. The veins are localized in a complex metamorphic rock assemblage which includes greenstones and felsic metavolcanic and volcaniclastic rocks, meta-exhalatives and metasediments. Gold occurs in the metamorphic host rocks in association with arsenopyrite and arsenic-antimony sulfides which occur in lenses and disseminations within the host rock. Gold grains occurring in the metamorphic host rocks range. in size from sub-micron to a few microns in diameter.

Jan 1, 1987

By J. S. Pitsillos

A new furnace tapping technique involving the simulation of a control valve at the exit to a furnace is being investigated. The purpose of this new tapping technique is to regulate the flowrate of liquid furnace products( slags, metals and mattes). Numerical modelling and experimental work has been carried out on tapping of slags leaving a SIROSMELT reactor and the results found to be in good agreement. Numerical modelling has also enabled prediction of the important industrial conditions for the onset of blockage from the shape of the pressure versus flowrate curves. Slag launder experiments have been carried out and a one-dimensional heat transfer model was used to evaluate the effectiveness of launder covers and different coolants. From the experimental results and mathematical model some launder design guidelines such as inclination angle, covers and coolants have been developed.

Jan 1, 1991

By T. Ueno

Naoshima Smelter & Refinery of Mitsubishi Materials Crop. commissioned a new Mitsubishi continuous copper smelter in May 1991. Process offgas volume of the conventional reverberatory furnace line, one of the previous smelters having been shut down, was very large and thus two acid plants had been operated. It was expected that the offgas volume would be reduced at the new smelter to about a half of the sum of those from previous two 1 smelters and the sulfur dioxide strength would be increased. So various alternatives were studied to minimize the operation cost. And it was decided to utilize both of the plants with minor modifications by diluting the gas either with air or with dilute gases. The acid plants now receive offgases from the new copper smelter, a sintering machine of a lead smelter and a decomposer of waste acid. The paper discusses plant design, operation, improvements and modifications realized in relation with the retrofitting of the copper smelter.

Jan 1, 1992

By H. Y. Sohn

The ignition and combustion of chalcopyrite particles under suspension-smelting conditions, in which the particle-particle interaction is neglected, has been analyzed by considering the intrinsic kinetics of oxidation and heat and mass transfer between the particle and its surroundings. Reasonable agreement has been obtained between the calculated results and experimental results from a laminar-flow furnace reported in the literature. This computation- al procedure has further been applied to flash-smelting conditions. Under suspension-smelting conditions (Sh = Nu = 2), chalcopyrite particles ignite at around 960 K. The effects of various parameters, such as oxygen concentration, particle size, and gas temperature, have also been evaluated. Comparison between calculated results in this work and experimental observations indicates that SO is the important gaseous product that forms at the surface of the particle.

Jan 1, 1993

By Yapeng Zhang, Zhiwen Shi, Chaoquan Yao, Fei Wang, Xinyu Li, Jianliang Zhang

A great deal of iron ores which have special elements have been applied in the sintering process with the decreasing of high-grade quality iron ores resources. In this paper, the laterite nickel ores were added into three different kinds of iron ores respectively to make liquid phase formation research by software of Factsage and high temperature characteristic sintering experiments. The results showed that the adding proportion of laterite nickel ores should be less than 15% when the high temperature properties of the mixing ores were well. Increasing the mixing ration of laterite nickel ores in the sintering blending would play an important role in the reduction of the sintering cost.

Jan 1, 2015

By Edgar Peek

Lixiviant regeneration is by definition a precondition for any hydrometallurgical process. In chloride hydrometallurgy either HCl or Cl2 has to be regenerated in order to establish an economically viable metallurgical process. One such regeneration process is widely used with steel pickling where HC1 is regenerated through the thermal decomposition of ferrous chloride in either spray roasters or fluid bed pyrohydrolyzers. This standard HC1 regeneration process deserves to be considered as a potential separation process, since thermodynamic calculations show that a fluid bed pyrohydrolyzer can function as a ferrous-nonferrous separator. Several nonferrous,metals such as zinc, lead and cadmium can be volatilized as a chloride under ferrous chloride pyrohydrolysis conditions. If such a nonferrous metal volatilization could be achieved in the case of slurry feeding of "contaminated" iron oxides, then this would increase the Fe/H2O ratio of the (process) feed and thus save on fuel per ton of iron, while yielding a marketable iron oxide product. Previous test work on synthetic materials revealed that the near-complete separation of zinc, lead and cadmium from iron oxide was possible in a pyrohydrolytic atmosphere, even if zinc was present as zinc ferrite (more than 99.5%). This investigation, which was carried out in a tube furnace at 1100 K has now been extended to treat synthetic zinc minerals and also franklinite ore. For the latter, it was found that 85% zinc volatilization could be achieved in 4 hours at 1300 K. It is postulated that complete zinc volatilization could not be attained due to the formation and/or presence of gahnite and hardystonite, which might be stable in HCl/H2O atmospheres at 1100 K. The effect of adding small amounts of calcium chloride to react with gahnite and hardystonite to give zinc chloride and both calcium aluminates and silicates is being discussed. Test work on slurry feeding of this complex ore in a recently constructed 4-inch diameter fluid bed pilot unit has been planned for the near future.

Jan 1, 1995

By Zhang Libo, Li Wei, Peng Jinhui, Guo Shenghui, L. Jing

Partially stabilized zirconia ceramics (PSZ) were prepared by microwave sintering using natural baddeleyite which was obtained by flotation of baddeleyite ore as starting materials. Because of using natural baddeleyite as raw and the process producing no waste, it realized shorter process, energy savmg, environmentally-friendly and non-damage processing. In this work natural baddeleyite stabilized with 3.8wt.% CaO were sintered at 1300°C for 60min in a multi-mode 2.45GHz microwave furnace. Microwave sintering could fast heating and sintering. Besides that, microwave sintering could heat materials wholly, low the sintering temperature, improve the materials properties and save energy. X-ray spectrum displayed the product composed by the tetragonal phase and monoclinic phase that also showed the product was PSZ. Fine and uniform microstructures were observed in the product through scanning electron microscopy. PSZ which was with high density was confirmed by the method of the Archimedes technique.

Jan 1, 2011

By Charles L. Richman

The effect of the addition of Silver Sulfide on the rate of Chalcopyrite (CP) of Sulfuric acid (H2SD4 leaching is discussed, Although Ag2S in an expensive addition, a theoretical explanation of it's use will aid in the development of a economic substitution. We have used cyclic voltammography to show the presence reaction species at different potentials. Cyclic Voltammography maps the surface reaction current peaks on CP, to regions on the CP Phorbaix diagram. AC Electro-lmpedance spectroscopy (EIS) models the surface impedance properties, which control the rate of electron and ion transfer, and the surface kinetic reactions, with and with out light. EIS and other measurements show that AgCuS u Photo-reactive material- The EIS results are compared with the SEM and EDXA results to show the presence of diffusion pores, and diffusion controlled reactions during CP leaching without the addition of silver sulfate. We hypothesize that AgCuS is an ionic conductor like Ag2S. EIS shows an imposed negative leaching rate greatly. Our theory shows how the formation of Silver Copper (1) sulfide layer at open circuit potential gives an effect similar to negative potential, that is enhanced with illumination. We verify that AgCuAS is an N-type semiconductor that forms a diode type junction with the electrolyte with the Mott-Schoottly relation.

Jan 1, 2001

By Robert E. (Bob) Brown

Magnesium was discovered by Davy in 1808. The production processes as they exist are not economically competitive with aluminum The electrolytic magnesium process is divided into two steps; one to make the MgCh feed and the other to apply large amounts of electric current to dissociate the feed into magnesium (450 g) and chlorine (1200 g). The production of fuJIy anhydrous, pure cell feed is a major problem Recently, there has been a growth of thermal processes, mainly the Pidgeon silicothermic production process using FeSi to reduce dolomite in horizontal retorts. Pechiney has a large vertical electrical furnace process that also uses FeSi to reduce calcined dolomite in a molten bath containing alumina. Work is proceeding to develop new or modified processes that will greatly improve magnesium production. The present methods and the research and R&D will be reviewed in this paper.

Jan 1, 2001

By Thomas W. Chapman, Shi-Chern Yen, I-Min Lu

"An electric field was applied to a metal-bearing kaolinite specimen to investigate the efficiency of electro-osmosis in removing heavy metals from contaminated soils. The electric field induces a flow of water through the porous medium, called electro-osmosis, which is superimposed on the hydraulic flow. Because the electro-osmotic flow is relatively stronger in smaller pores, it can enhance the displacement of contaminated solution by fluid convection. Furthermore, local changes in pH caused by the electrode reactions can affect adsorption equilibria and the distribution of solutes between the solution and the solid surfaces.The electro-osmosis experiments were conducted by applying either a constant current or a constant voltage across 8-cm inside diameter, 25 to 30-cm long specimens of kaolinite clay with graphite electrodes. Samples of the pore fluid and of the clay were analyzed to determine metal content, pH, and conductivity as functions of time and position. Results show that removal of heavy metals from soil can be accomplished effectively by electrokinetic treatment of sufficient duration. Approximately 95% of the lead was removed after 189 days.IntroductionRemediation of soils contaminated with toxic chemicals is a difficult and expensive task. Washing or leaching are not particularly effective if the contaminate is sequestered in small pores; hydraulic flows of water pass through larger pores leaving the smaller pores relatively untouched. Electro-osmosis appears to be the most promising new technology for removing heavy metals and organic substances from contaminated soils (Segal, 1980; Hamed et al., 1991, Masliyah, 1994).Electro-osmosis is one of several electrokinetic phenomena that occur through the interactions among an electric field, fluid motion, solute adsorption, and the existence of a net charge on a solid-fluid interface (Newman, 1991, Masliyah, 1994). Electro-osmosis refers to the fluid flow in a porous medium that results when an electric field acts on the mobile region of the electrical double layer, the solution-side region of charge separation that exists at the pore walls."

Jan 1, 1996

By Atsushi Shibayama

The aim of this research was to develop a copper recovery process from mine tailings (0.34%Cu) using flotation followed by high-pressure oxidative leaching (HPOL) and solvent extraction. The results of HPOL using the concentrate of mine tailings obtained by flotation under the optimal conditions of the previous study shown that an efficient copper dissolution of 94.4% was achieved in an H2O media, while the copper concentration of PLS reached to be 2.9 g/L. The solvent extraction of PLS obtained from the optimal HPOL showed that 91.3% copper was recovered in stripped solution under the determined optimum conditions, in which the copper concentration achieved to be 44.8 g/L. Finally, a proposed copper recovery process from the concentrate of mine tailings was developed by combination of HPOL and solvent extraction, while a total copper recovery of 86% was achieved.

By Liming Wang

One of the steps in the extractive metallurgy of lead is a refining process called drossing. Hot dross is mixture of impurity compounds that form on the surface during the cooling of lead blast furnace bullion, and in Missouri, the main impurities are copper and sulfur. The slow cooling of bullion throws out of solution all other minor impurity elements (or their compounds) which are much less soluble at lower temperatures (mainly nickel, arsenic, iron, and zinc). The transfer of bullion from the blast furnace to the refinery and the subsequent hot drossing step cause fugitive emission of lead-containing fume and dust, which creates a plant hygiene problem. One cause of the emissions is the high vapor pressure of lead and its compounds during transmission of = 1000 °C bullion to the drossing kettle. Another cause is the lifting of dross dust during manual skimming of dross. The environmental problems associated with the traditional hot drossing process provided an incentive to investigate a new drossing process that avoids contact between plant air and hot bullion or dross. A key aspect of the process development was a detailed mineralogical examination of dross from two different bullions. The bullion samples were cooled at different rates, and the dross filtered out and examined. The morphology, phase identification, and composition of the dross was examined by optical and SEM microscopy. The principal dross phases were copper and cuprous sulfide, galena, a complex sulfide containing copper, nickel and lead, and speiss (containing nickel, cobalt, iron, copper, lead, and arsenic compounds). The copper was acicular, with nickel and arsenic in solid solution. The cuprous sulfide was largely digenite in a granular or dendritic form. A substantial part of the dross was solidified matte with a eutectic microstructure, consisting mainly of CU2S and PbS. Small particles (some of which had a eutectic microstructure) never floated to the surface of the lead during the slowest cooling rate, thus indicating that flotation of tiny matte droplets and dross crystals is exceedingly slow. The success in separating dross and lead by centrifugal filtration suggests its application in industry as a replacement for traditional hot drossing.

Jan 1, 1995