Search Documents

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

THE production of titanium in 15-1b. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,1 has provided adequate material for a study of the : physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the properties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. [ ] CONSOLIDATION OF THE POWDER The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at so tons per

Jan 1, 1946

By D. D. Dunkin

Sandstone has been prepared for glassmaking purposes, and marketed from the White River Valley in Arkansas at Guion, Izard County, since about 1910—soon after the completion of the White River Branch of the Missouri Pacific R. R. Co. Until 1921, operations were somewhat spasmodic and ended in many failures. In that year a plant was built by the Silica Products Co., Inc., and since that time the operation has been continuous and steady. The land is held under leases, covering about 30 square miles of the best sandstone adjacent to the railroad. Most of the product is shipped to glassmakers. Geology The St. Peter sandstone is rather widely distributed in north central Arkansas and is exposed most prominently in outcrops along the slopes of the White River Valley and its tributarirs that form the division between the Boston Mountains to the south and the Salem Plateau of the Ozarks to the north. It is of Ordovician age and is generally underlaid by Cotter dolomite and capped by Plattin limestone, except in the vicinity of Bellefonte and Everton. At those places, it is a massive cross-bedded, laminated, saccharoidal sandstone; underlying it is the Everton limestone and overlying it, the Joachim magnesium limestone The sandstone at Everton contains numerous phosphatic pebbles and inclusions of sandy limestone. The irregularity of cross-section, the evidence of sorting action and the phosphatic pebbles appear to be indications of secondary deposition The St. Peter sandstone occurs as a massive formation in the picturesque bluffs along the White River Valley from near the eastern escarprnent of the uplift northwestmard into the Ozarks. The exposure shows a series of gentle anticlinal and synclinal folds. The greatest thickness is at the southeastern end, where it is over 100 ft. in many places. It thins out to the north and west and then to isolated and scattered deposits which cap the ridges and mountains of the Ozarks.

Jan 1, 1928

By ARCHIBALD DOUGLAS

AT various times during the past quarter century proposals have been made that the basic Federal mining law of 1872 be repealed or amended, and that in its place a new and simpler law be enacted to provide for the entry upon, working, and the taking up of claims on the unallotted Federal mining lands in our western states and in Alaska. Serious discussion and study have been given such proposals but little has resulted there from, except perhaps a lively interchange of opinion and the conclusion that though the Apex law of 1872 is in many ways highly unsatisfactory and frequently a fomenter of strife and trouble, it still bids fair to remain with us. Under this act a greater part of the non-ferrous mining industry of the United States has developed. With all its short-comings it is the legal bridge that has carried over the innumerable caravans of adventurers and prospectors who explored our mining frontiers. For without any amendments of substance this act has for fifty-eight years been the guide in the location of our western Federal mineral claims and has stood unchanged during the most important period of our mining history. While Federal and state acts and amendments have been ground out by thousands and tens -of thousands the mining act of 1872, with a :strange tenacity, has remained as constant as the Rock of Gibraltar, and under it states, mining districts, and local customs have developed different codes for its application but its fundamentals have been unaltered. "Use doth breed a habit in a man"; until now the application of the law of 1872 has become a second mining nature.

Jan 1, 1930

By M. Schmellenkamp

By comparing two longwall operations, one begun in 1956 and the other in 1960, the author is able to demonstrate the increases in production and performance made possible by longwall mining. These achievements have been brought about by continuous development of longwall mining equipment and associated roof supports. Because of this progress, longwall mining is able to provide, under proper conditions, high production per man-shift, remarkable cost savings, dependable roof control, safe working conditions and truly continuous production. It may seem odd that the title of this paper is not simply "Longwall Mining" but instead "Progress in Longwall Mining." However, the word "Progress" definitely has its place in longwall mining. If it had not been for progress in the development of longwall mining equipment and roof supports, the longwall mining method would not be able to compete in production and performance with modem coal mining machines. The longwall mining method was practiced at the beginning of the century and there were several successful operations in coal fields in Illinois. In those early days of longwall mining, the coal was undercut by hand 2 to 2.5 ft at the bottom of the seam and packwalls were built in the gob to support the roof. The roof eventually subsided and the weight of the subsiding roof was used to ride the face and break the undercut coal. Utilizing natural weight to soften the coal face is still practiced in modern longwall mining; however, the packwalling method has been replaced by the caving method and the roof is now supported by yielding steel roof supports and forepoling steel headers. The purpose of these yielding-type roof supports is to provide a safe working area for the crew along the entire longwall face, to permit continuous mechanical mining across the prop free face, and to provide a strong resistance for the roof by forming an even breaking line at the gob for the roof to cave. Roof supports and associated forepoling headers should be kept as close as possible to the face in order to prevent a caving between face and supports, especially under friable roof. This means that the coal should be extracted in small slices, allowing only a narrow roof area to be exposed and unsupported. The coal planer with its relatively high cutting velocity of 75 ft per min provides such an extraction of coal and has proved its high performance under difficult mining conditions. Since 1951, several longwall faces in southem West Virginia and Pennsylvania which have been equipped with the coal planer and friction-type manual roof supports have been successfully operated. Compared to today's longwall mining, these longwall faces required such a large crew, primarily to handle the roof supports, that the actual high production per shift was charged with too high a labor cost, thereby decreasing the tons per man. Yet, even then the longwall faces outperformed the conventional mining system under the same conditions. In order to demonstrate the progress that has been made in the development of longwall mining, a comparison will be made between a longwall face in Arkansas which was installed in 1956 and a modemized longwall face started in 1960 in southern West Virginia. LONGWALL MINING IN 1956 The 320-ft longwall face was developed in a 32-in. thick coal seam near Greenwood, Ark. The method of mining the 320-ft coal block was the advancing system in which three entries on either side of the face were driven ahead of the advancing longwall face. The face was equipped with a coal planer and a Panzer conveyor; timbering was done with wooden timbers and cribs. The roof supports were set without any pattern. The crew to operate the planer and to handle the roof supports (timbers and cribs) consisted of 15 men per shift. During a period of approximately eight monthsof single shift operating time, the average tonnage produced in this relatively low seam amounted to about 263 tons of clean coal per shift. To show the development in the coal plow from then until now, it should be pointed out that the standard plow was used in this operation. The plow was equipped with rigid bottom bits which could not be adjusted if the plow started to climb, thereby leaving bottom coal to be recovered by pick hammers end causing delays in production. The height of the plow

Jan 1, 1963

By Max W. Ball

Our ever-increasing use of minerals has been the outstanding fact in our American economic development. The rise in our standard of living in the past century is without equal in human history. Nowhere in time or place has the man who works lived so well, or the man who cannot work been so well cared for. We live in a new world, even the poorest of us, that our forebears of 1849 could not have dreamed. That new world has come mainly from our use of minerals. Our per capita use of nonmineral products has grown too, but by only a modest amount. Food consumption per person has grown about 15 per cent in the past fifty years; lumber use per person ,has fallen 56 per cent and that of wood for fuel 65 per cent. Of all the products of field and forest, our use, per capita, may have increased by one fifth during the present century. In contrast, our per capita use of minerals has multiplied several times. Each of us uses 2% times as much steel and 16% times as much petroleum as our fathers used in 1900. In less than half a century our per capita consumption of all minerals has probably risen by 200 to 250 'per cent. Man once built with wood; today he builds mainly with brick and stone and steel. Once he traveled by the power of hay and oats; today he travels by the power of coal and oil. Rubber made from minerals is already better for some uses than rubber tapped from trees; before long it will be better for most and perhaps all uses. Even our ladies' graceful legs are clad in mineral fiber, where once animal or vegetable fiber would have covered them. Our high standard of living is a product of the machine.. The machine is made of minerals. The machine is driven by minerals. The machine age is a mineral age.

Jan 1, 1949

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal were mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-year periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to in- crease. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu yd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu yd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can be recovered by underground mining. 5) Some coal measures can best be extracted by surface mining

Jan 1, 1981

By Dr. O’Neil Thomas J., Donald W. Gentry

"October. This is one of the peculiarly dangerous months to speculate in stocks. The others are July, January, September, April, November, May, March, June, December, August and February." -Mark Twain Although the preceding chapters describe the type of preliminary evaluation frequently performed in the mining industry, it has been assumed that input data are known with certainty-clearly an enormous simplification. In reality, estimates of ore grade, mining cost, metal price, etc., are subject to varying degrees of uncertainty due to the inability to predict the future with much precision. Management would probably not, for example, be equally attracted to two projects each offering a 20% DCFROI-one for a new gold venture in Nevada and the other for an undersea manganese nodule operation in the Pacific. The high risk with the latter investment tells the obvious; there is more to investment decision-making than a deterministic analysis using "best estimates" of input parameters. The science of decision theory normally distinguishes between decisions under uncertainty, where probabilities of various outcomes are unknown; and decisions under risk, where such probabilities can be estimated. The first case is rarely en- countered in practical capital investment analysis in mining, so the remainder of this chapter focuses on that class of problems where rational probability distributions for the future states of input variables can be estimated. RISK IN MINING Risk in the context of this chapter is the unforeseen deviation of individual cash flows from expected values for a capital project. For a mining venture, the source of this uncertainty could be any number of factors relating to such items as ore grade, ore reserve tonnage, operating costs, product prices, etc. With conventional *Adapted from O'Neil, T.J., 1979, "Procedures for the Preliminary Financial Evaluation of Metal Mining Ventures," Computer Methods for the 80s, A. Weiss, ed., AIME, New York, pp. 556-573.

Jan 1, 1984

By B. A. Cheadle, K. P. Steward

Axial tensile, ring tensile, closed end burst, and free end burst tests were done at room tempe.vature and 300°C on three batches of Zircaloy-2 sheathing zuith different textures. Knoop hardness tests were also done on all batches. The mechanical properties of the tubes were largely dependent on the percentages of cold work, but were also markedly affected by the textures, particularly with respect to deformation behavio'r. The deformation behavior observed confirmed Picklesimer's predictions, zuhereas Knoop hardness results could be correlated with texture and yield strength anisotropy after the ,method of Wheeler and Ireland. From the mechanical properties, and from efjectiue strain values deterrlzined at the fractures using a photoqid technique, it zuas concluded that tubing witlz a single preferred orientation of radial basal poles best combines strength and ductility for any given deqee of cold work. THE mechanical properties required in collapsible Zircaloy-2 fuel sheathing for water-cooled power reactors are strength to resist wrinkling deformation by coolant pressure and ductility to accommodate a small amount of deformation in service without rupturing. Zircaloy-2 tubing during fabrication develops pre- ferred orientations of the a Zr grains due to aniso-tropic deformation behavior, and these textures markedly affect mechanical properties. Picklesimer' had predicted the deformation behavior of tubes with various textures, but the texture required to provide the optimum strength and ductility for a given degree of cold work has not been reported. To investigate this problem, tests at three transverse to axial stress ratios were done at room temperature and 300°C on three batches of Zircaloy-2 tubing covering a wide range of textures and percentages of residual cold work. Knoop hardness values were also measured to correlate with preferred orientation and yield strength anisotropy after the method of Wheeler and relland.' 1) MATERIAL For this investigation, three batches of tube-reduced tubing were chosen from the Zircaloy-2 sheathing produced for the Douglas Point Reactor. Individual tubes were 191/2 in. long, 0.600 in. OD, and 0.0165 in. nominal wall thickness. The identities of the batches, together with their textures, are shown in Table I. The tubes had the normal Zircaloy-2 composition3 of 1.5 wt pct Sn, 0.3 wt pct Fe, Ni, Cr combined with the following oxygen concentrations: Batch VII 1140 to 1390 ppm 0 Batch VIII 1400 to 1750 ppm 0 Batch IX 880 to 1320 ppm 0

Jan 1, 1968

By Clyde E. Williams

DESPITE the confusion resulting from the depression and the beginnings of recovery, important progress in all branches of iron and steel metallurgy has been accomplished during the year 1933. Research work has been intensive and highly technical, with increasing attention paid to fundamentals. Plant application of research developments has been rapid. Highly specialized laboratory methods were used for the study of iron-ore concentration methods. More attention has been given by the blast-furnace operator to the sizing of ore and the elimination of fines from the charge by the use of sinter. Combustion in the open-hearth has been placed under better control and the insulation of open-hearth furnaces has spread rapidly, with resultant higher fuel efficiency and better control of the melting and refining operations. Control of iron oxide content in the slag and the determination of iron oxide and other inclusions in steel received great attention during the year.

Jan 1, 1934

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By John Chipman, Karl L. Fetters

Tax relationship between the composition of the slag and that of the underlying metal during the refining of a heat of liquid steel may best be studied in the light of the two broad physicochemical concepts of equilibrium and reaction rate. Actual steelmaking processes, typified by basic open-hearth practice, involve such complexities of operating variables that it is impossible to distinguish with any degree of certainty between the general limiting conditions imposed by chemical equilibrium and the effects associated with rates of diffusion or of chemical reaction. Further advances in the physical chemistry of steelmaking will depend upon our ability to distinguish clearly between these two kinds of effects, and the experimental work that must be done falls naturally into two classifications. The first is the study of chemical equilibrium that cannot be carried out with assurance under operating conditions but must be done in the laboratory. The second is the subject of rates of reaction and diffusion and the mechanism of the process as a whole, which can best be studied under operating conditions. The latter is not entirely independent of the former, since its interpretation often requires a knowledge of the equilibrium state. It is the purpose of this and of several papers that will follow to present the results of laboratory investigations of equilibria involving liquid steel and slag. Open-hearth slag is a complex mixture containing at least eight major components and perhaps twice as many whose influence may be classified as probably minor. It is not surprising that progress toward a complete understanding of such a material at high temperatures has been slow. Attempts to apply the established principles of physical chemistry to the behavior of the individual components of this mixture have been beset by an almost complete lack of data on its chemical properties in the liquid state. This has necessitated the adoption of various methods of approximation based upon such assumptions as, for example, that for a given component the ratio of its mol fraction in the slag to that in the metal is a constant, or that the molecular composition of the liquid slag is the same as its crystalline constitution after solidification. From the thermodynamic viewpoint, such assumptions are merely useful dodges, which enable one to hazard a guess as to the magnitude of the more fundamental quantities, the chemical potentials and activities of the components of slag. The problem of determining the activity of each substance in an eight-component system seems too complex to be undertaken without the aid of generalizations derived from experimental data on similar systems containing a smaller number of components. Accordingly, it was planned in the present investigation to study the equilibrium of molten iron with the simplest

Jan 1, 1941

By Jonas Svensson

A new method is described for the production of cold-bonded pellets using a hydraulic binder, such as portland cement. Large-scale pilot-plant tests have proved that self-fluxing pellets of high reducibility and good handling strength can be made by the method. Blast-furnace trials have shown that the pellets are an acceptable burden material, comparable with self-fluxing sinter or heat-hardened pellets. Economic factors of commercial-scale production are discussed. The Grangcold Pellet Process—for which patents have been applied or already granted in a number of coun-tries—uses a hydraulic adhesive such as portland cement, slag cements, pozzolanic cements, etc., for the production of cold-bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron-ore fines is not new. Portland cement was proposed as an adhesive for cold-bonded iron-ore briquettes in patents granted more than 50 years ago.' In a report on the briquetting of iron-ore fines, published in Stahl und Eisen in 1959; it is stated that briquettes bonded with portland cement are used on a small scale at an ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft, and difficult to store and handle. The Grangcold Pellet Process has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrated during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus, the mixture can be stored in a stockpile or in a bin until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening. The binder preferred for the Grangcold Pellett Process is portland-cement clinker, ground without the admixture of gypsum in order to avoid sulfur in the pellets as far as possible. Usually a 10% binder content is used. Two-thirds of the portland-cement clinker consist of lime and the rest is silica, alumina, and ferric oxide. Thus, self-fluxing or overbasic pellets are produced with this binder if the amount of silica in the concentrate used does not exceed 4%. The Grangcold Pellet Process was developed by the mineral Processing Laboratory of the Granges Co. Work started in 1963 with batch-scale tests. In 1966, a small pilot plant was put into operation in which 1800 tons of pellets were produced using 10% of rapid-hardening portland cement as a binder. Favorable results from a blast-furnace test with this batch led to the decision to erect a larger pilot plant which went into production in the summer of 1967. Since then, approximately 100,000 tons of cold-bonded pellets have been produced, mostly with 10% gypsum-free portland cement as a binder. Several full-scale blast-furnace trials have been performed with the pellets. The results of the trials indicate that the Grangcold pellets constitute a satisfactory blast-furnace feed. An industrial plant for the production of Grangcold pellets with a rated capacity of 1.5 million tpy is now under construction at the Granges Co.'s mine at Grangesberg. The plant will come into operation in the summer of 1970. Results from Laboratory Work Pellets made from iron-ore concentrate bonded with portland cement harden slowly and their handling is very critical until they have hardened enough to loose their stickiness. It is therefore especially important to study the progress of the hardening action and the factors influencing it. This is best achieved by investigating the relationship between the compressive strength of the cement-bonded pellets and the curing time under varied conditions. The general course of this relation-

Jan 1, 1971

By W. TRINKS

RAPID progress has been made in the automatic control of open-hearth furnaces in the past few years and many firms today\supply such control apparatus. It is somewhat surprising that so little was heard about open-hearth control up to about, 1928, and that thereafter the practice of automatically controlling open-hearth furnaces spread very rapidly. Before discussing the reasons for this it may be advisable to list the quantities that can be controlled. One of the easiest quantities to be controlled in the open-hearth furnace is pressure. The reasons for controlling it are plain. If there is excess pressure in the furnace, products of combustion leak out around .the .door and through all the cracks in the brick-work. The stability of the piers between the doors is seriously endangered, and front wall repairs become frequent. Furthermore, hot gases are lost that might be usefully employed in heating the checkerwork. If there is a slight vacuum in the furnace, cold air entering through the doors and cracks cools the interior, slowing down the reactions and making it impossible to secure the highest degree of preheat from the checkerwork.

Jan 1, 1931

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of com- plaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and ensure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage or breakage en route. The small sizes present in a car of prepared coal as received by the purchaser consist-of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' lass because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal.

Jan 1, 1943

By S. V. Krusiewski, J. W. Gabelman

Regional metallogenic zones and areas of equal paragenetic range have been interpreted from a compiled metallogenic map. of Mexico. Mineralization gradients of the pattern subsequently identified extend inland from coastal zones of high-temperature mineralization, and join in a central longitudinal zone of relatively low-temperature mineralization, apparently leaving no zonal room for lowest temperature deposits. The striking regional zoning pattern can be correlated with regional deformation gradients of similar position and orientation. The gradients represent at least three major orogenic cycles in two structural belts. Paleozoic structural belts existed along each coast with deformation gradients diminishing inland toward a narrow, central peninsular craton. The Mesozoic-Tertiary Mexican (Cordilleran) belt covered the entire country with a gradient oriented toward the Gulf of Mexico. Most ore deposits in this belt are of Tertiary age, although Tertiary mineralization gradients seem to have "inherited" the pattern left by Paleozoic tectonic gradients. Mineralization gradients can be used to identify the regions most favorable for the occurrence of selected metals. A metallogenic province is characterized by particular proportions of various metals, and the relative proportions can vary from province to province; but within any province the same intensity of mineralization would produce similar deposits in different places. Declining intensity of minetalization produces different kinds and sizes of deposits in zones that are concentrically arranged around sites of strongest rock alteration. On a regional basis, districts of similar average intensity of mineralization occur in zones that generally parallel some tectonic grain with the result that tectonic deformation has been designated a principal cause of mineralization. Variations in the type and intensity of deformation would determine the type as well as size of metal deposits. Mexico is especially favorable for such a study be- cause of its great abundance and variety of epi-genetic mineral deposits in various lithologic, structural and tectonic environments. The concept is also useful in recognizing portions of Mexico favorable for the occurrence of specific metals. METALLOTECTONIC ZONING IN MEXICO Theory: In studies of individual districts and groups of districts throughout North and South America, areal zoning of metal deposits generally seemed to respond to the paragenetic sequence of iron, gold, copper, zinc, lead, silver, antimony and arsenic, gold and fluorite. However, the definition of district zones is greatly obscured by contemporaneous or rhythmic deposition of metals, especially in the middle of the paragenetic range, and by the common superimposi-tions of different generations of metals. Zones could usually be distinguished only for groups of metals, such as early precious metals, base-metal sulfides, sulfosalts and late precious metals. The best defined zoning in a district is normally the spatial separation of the greatest volumes of altered and metallized rocks.' Exceptions are districts representing the high- and low-temperature extremes of the mineralization range where the former creates a matrix for the latter. In most districts the total quantity of alteration products is greatly in excess of, and appears to be roughly proportional to, the total quantity of metallization products. Subsequent to the bicomponent nature of each district, the most important mineralogical feature is the great excess of one to several metals or minerals which results in a district identifiable as one of predominantly gold, copper, lead-zinc, fluorite, etc., although a great variety of other elements may be present. The para-genetic range for the abundant elements in any district is only a portion of the entire possible range for all the elements representing the complete process throughout the region. Early during investigations of this type, it became apparent that the consistent bicomponent character of districts allows two methods for studying epi-genetic mineralization patterns. One is to identify and plot altered rock "pipes,"* which are easily recognizable in the landscape by their anomalous

Jan 1, 1969

By G. W. Tower

THE YEAR 1931 was for most American copper producers one of restricted output but extremely low production cost.. When compared with 1929, the marked reductions in costs achieved in 1931, operating at rates in many instances a third to a half of capacity, can only be regarded as remarkable. In fact, the recent shut-down of several large operations suggests the probability that 1931 costs represent a bare minimum for many properties. Before discussing the 1931 results a few remarks on cost data are appropriate. The type of cost tabulation here presented was first published in 1929, (A. B. Parsons. E. & M. I. June 8, 1929), and has appeared each, succeeding year following in general the calculation method and company set-up of the original article. (. G. W. Tower, E. & III. L, July 8. 1930; S. D. Strauss, E. & M. J.; July 27, 1931). As far as possible the leading American copper companies are included. In considering these cost tabulations it must be borne in mind that the information from which they have been prepared is entirely contained in the annual report of each company; and that a multiplicity of interests and a condensed income statement for some of the larger companies, such as Cerro de Pasco and Kennecott, make the cost figure an arbitrary one depending upon sundry metal credits, metal products, miscellaneous income, etc. For Granby, Howe Sound. Magma, and Noranda, sundry metal credits are important. Furthermore Andes, Chile and Greene Cananea give costs only against copper sold. Although the individual costs here figured are by no means absolute they are computed by the same method each year and offer a basis of annual comparison; and with attention to footnotes the premises on which the costs are based may be easily followed.

Jan 1, 1932

By Brehon B. Somervell

SOMEONE has called this war a war of gadgets. Someone else says it is an engineers' war. It is a war of production, transportation; a war in the sky; a war on wheels; a civilians' war. Let us not quarrel about nomenclature. Call it what you want. If four motored bombers and thirty-ton tanks are gadgets, then it is a gadget war. Engineers, scientists, shop laborers, air-raid wardens all have their highly important jobs to do. The fact remains that this war, like all others, is a soldiers' war. The basic strategy employed today is the same strategy that Philip of Macedon used on the Plains of Thessaly twenty centuries ago. His phalanx was a striking force armed with every known weapon. It was armored with breastplate and casque. It depended for success on superior man power and mobility, upon superior weapons and supply, and upon superior discipline. It executed commands faster than its enemies; it had more catapults and spears, more men in the back areas bringing up supplies. It was a new idea. It used what today we call the scissors movement to cut up its foes. It took sharp advantage of surprise. It introduced terror as a weapon-terror inspired by a vast, moving, shouting army with banners. It laid waste the cities by fire. The Greeks had a word for it but that word wasn't "blitzkrieg."

Jan 1, 1942

By J. T. Mackenzie

Henry Marion Howe, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius. Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: " Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up—by masses of graphite ..." Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in I900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on "The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro-structure of the metallic matrix, Professor Howe pointed out that "such minor structural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By J. T. Mackenzie

Henry Marion Howe, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius. Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: " Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up—by masses of graphite ..." Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in I900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on "The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro-structure of the metallic matrix, Professor Howe pointed out that "such minor structural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944