Search Documents

By Cindi Byrns, Andy Davis, Amy Tisdale

The Robinson district, Ely, Nevada is a hydrogeologically complex system with several distinguishable geologic blocks, each with a distinct background groundwater chemistry. To discriminate between background and mine-impacted groundwater, background wells, monitoring wells, pit lakes, waste rock seeps, and surface water samples were analyzed for a suite of major cations and anions, together with trace and precious metals, rare earth elements, 2H-deuterium and 18O/16O. The data allowed identification of groundwater flow paths, verification of hydrochemical source areas and characterization of natural attenuation mechanisms (e.g., mixing, dilution and mineral precipitation) that control the concentration and migration of metals at the site.

Jan 1, 2000

By Ralph P. Hackl

The Congress gold property, located near Goldbridge, B.C., is extremely refractory with most of the gold disseminated in fine- grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225 cubic meter commercial size bioleach reactor was built and tested at the mine site in 1989. At that time the tank was the largest bioleach reactor ever operated. This paper discusses our experiences in operating the tank, summarizes some of the data obtained and describes the problems encountered.

Jan 1, 1990

By A. E. Reisenauer, R. W. Nelson, G. W. Gee

A model assessment was made to evaluate contaminant transport to ground water from clay-lined and unlined tailings pits. The input hydrologic soil characteristics were measured on materials typical of those found at the Morton Ranch uranium mill site in central Wyoming. The assessment involved combined saturated and partially saturated flow and contaminant transport models for two-dimensional cross-sections typical of the proposed Morton Ranch burial pits. Specifically obtained from the models were contaminant flow paths, the advancing contaminant flow fronts for sorbed and non-sorbed constituents, and travel times of contaminants along flow paths. Such results enable evaluation of the environmental consequences for the alternative control methods.

Jan 1, 1980

By David V. Fitterman, David L. Campbell

We've used direct current resistivity (DC), electromagnetic (EM), induced polarization (IP), and ground-penetrating radar (GPR) geoelectrical methods to study mine dumps. The results reflect lithology, pore water saturation, and dissolved solids in the pore water. If the pore water has a pH less than 5, conductivity maps can indicate acid generating potential. IP measurements can help distinguish mineralogy in mine dumps, especially concentrations of sulfide minerals. EM and DC can help locate acidic/high TDS groundwater associated with mine dumps. GPR methods failed at the sites we studied in the West. Our own conclusions are augmented by those from the recent literature.

Jan 1, 2000

By J. D. Carson

A 0.60 km2 (150 acre) wetland was reclaimed by Agrico Mining Company as part of a 1.48 km2 (366 acre) reclamation program in southwest Polk County, Florida approved by the Florida Department of Natural Resources. The upland portion of the area provides watershed for the wetland site which overflows into the flood plain of Payne Creek. Construction of the wetland was designed to provide conditions favorable for a diversity of habitats, as well as retention time for surface runoff waters. A variety of revegetation methods, including innoculation with muck from unmined wetland depressions, have produced encouraging results with both woody and herbaceous species.

Jan 1, 1983

By William J. Wiehagen

The training of mining personnel is a large and continuing activity for the mineral industries. Although safety and skills training has long been recognized as an essential element for reducing injuries and improving productivity, the research literature lacks definitive reports documenting the specific value of such training. The training literature presents a variety of testimonials as to the "benefits of training," but lacks data that specifically tie that training to the performance of the worker.

Jan 1, 1983

By C. H. Bucknam

Acid neutralization titrations were applied to the characterization of soil and overburden for the control and prediction of acid rock drainage in the coal fields of the eastern United States in the 1970?s (1). These became known as the Sobek methods as a result of the early United States Environmental Protection Agency publication and the methods have been modified (2) to be adapted to many applications in the metal mining sector (3,4,5,6,), and, as a result, there are a large number of acid neutralization potential methods being used that are referred to as Modified Sobek methods. Standardization of neutralization potential methods for metal bearing ores and related materials based on carbonate carbon, rather than titration, commenced in the 1990?s through the American Society of Methods and Materials (ASTM) Committee E01 on Analytical Chemistry for Metal Ores and Related Materials Subcommittee E01.02 on Ores, Concentrates and Related Metallurgical Materials (7). A subcommittee section, E01.02.05 on Environmental Methods, was organized to coordinate the method and material standardization efforts of ASTM and the Acid Drainage Technology Initiative Metal Mining Sector (ADTI-MMS) Prediction Committee (8), which took on the project of standardization of the acid neutralization potential acidity titration method (ANPA) to supplement the carbonate carbon method in E1915 (9) for application to samples which have metal carbonates (10), in particular, which result in overestimation of the neutralization potential using the carbonate carbon methods (11).

Jan 1, 2010

By Rene Padilla, Siyanda B. Mngadi, Gerrie van Aswegen, Peter Stonestreet

While many mine tunnels are developed through ground that must be riddled with the sources of small (and larger) mining induced seismic events, recorded by the mine seismic monitoring systems, we do not see planar discontinuities classified as seismic sources in the geotechnical databases. Here we list criteria that may be useful to identify discontinuities in drill core which are dynamic slip surfaces, parts of mining induced seismic sources. Such shear rupture surfaces in core would generally be powdery, cohesionless, and rough on cm scale. Finely broken rock and rock flour may be found in the core boxes at the discontinuities. Slickensides would be soft (easily destroyed) and kinematically consistent with the local stress field. In some cases, a cross fabric would be present, orthogonal to the slickensides, being the intersections of en-echelon extension fractures, within the dynamic shear zones, with the shear zone walls.

Apr 26, 2022

By F. W. Brackebusch

Paste is a high density mixture of water and fine solid particles with a relatively low water content (10-25%) such that the mixture has a consistency as measured by the ASTM slump cone test from slightly greater than zero up to nearly 12 inches (305mm). Particles of different size classes will not segregate or settle when the paste is not being agitated or when it is stationary in a pipeline. Cement may be a component of paste. Larger particles of aggregate can generally be added to a paste without greatly changing the pipeline transport characteristics. A paste may bleed water slightly when it is allowed to be motionless for periods of up to several hours, but the solids do not become so dense that the paste cannot be easily re-fluidized. The dividing line between the definition of a high density slurry and a paste is not sharp. It is a practical matter that must be considered when designing a pipeline transportation system. If the pipeline is very short, there is very little risk of plugging the pipeline with a high density slurry when flow is stopped for short time periods. With longer pipelines the mixture must remain stable without motion for periods as long as several hours to avoid pipeline plugging. The fine particles in a paste mixture can be composed of mine tailings or naturally-occurring clays, silts and fine sands. The mineralogy of the particles thus can have a wide variety from quartz and feldspar to clays, micas and even salts.

Jan 1, 1993

By C. M. McCulloch

More and more mining underground is being conducted using the longwall method. Likewise, many new surface mines use area or mountaintop removal methods. These methods can have a significant impact on surface and groundwater resources. The overall study of the effects on surface and groundwater from mining is referred to as the probable hydrologic consequences (PHC) determination of mining and reclamation. Collection and interpretation of information concerning groundwater and surface water quality and quantity, as well as detailed geologic analysis, is required to adequately define the impacts of mining. This paper discusses the present day requirements and methodology of preparing a PHC for a large mining operation in the eastern coalfields.

Jan 1, 1995

By V

"Recent regulations, as well as a general aversion to central dust collectors within the Powder River Basin Coal user’s community, have created a need for an alternate method for eliminating airborne dust. This paper addresses the capital expenditure as well as the cost of ownership of an integrated point source air cleaning system in comparison to a central collection system. This assessment was conducted by comparing the cost to purchase and operate a central dust collection system and integrated air cleaner system on a typical multiple transfer point application. The central dust collector consists of a negative pressure blower, a series of filter bags, a collection hopper, a screw conveyor to place collected material back into the material stream, and a series of ducts to pull air and dust from individual pickup points. The point specific integrated air cleaners consists of a negative pressure blower to pull dust and air from an application point through a bag-less filter media located at the application point. The agglomerated material is then redeposited into the material stream at point of use without the need for ducting or a central material hopper. The assessment yielded a 54% reduction in capital expenditure and a 26% reduction in operating costs for the same application when using individual dust filters as opposed to a central system. In addition to the lowered cost, there are reductions in risk associated with the elimination of ductwork and the central containment enclosure for collected explosive dust. By the conclusion of this paper, the reader will have a better understanding of the quantifiable differences between a central dust collection system and a set integrated air cleaner systems. BACKGROUND Spillage has always been a problem in the bulk solids handling industry. As long as there have been conveyors, there has been spillage. Spillage is material that falls off a conveyor belt and creates a hazard in the environment around a conveyor belt."

Jan 1, 2016

By C. Y. Haas

Of all the industrial clay minerals, attapulgite probably enjoys the widest variety of applications. A review published over three years ago by Haden and Schwint (18) cited some 80 individual uses, a list which continues to grow. In its near half-century of commercial life, attapulgite has received a generous share of research study and patent development effort, both on the part of producers as well as consumers. This work has been divided between understanding the mineral's structure or properties and applying it to specific end-uses. Naturally, information gained from the former has pointed toward opportunities in the latter. References of particular significance are cited throughout the text. Attapulgite's variety of uses derives from the unique three-dimensional structure and needle-shaped particle form of this crystalline hydrated magnesium aluminum silicate. Its inherent colloidal and sorptive properties are well known, and distinguish it from its sister clay minerals. Attapulgite is characterized by its high surface area, porosity, sorptivity, and decolorizing power. Its slips or slurries are viscous and thixotropic, however, unlike bentonite are not flocculated by electrolytes. In Table I are compared the general properties of attapulgite, bentonite, and kaolin. The properties in Table I are documented in greater detail by the wealth of scientific literature which has been published on the composition (14)(15), structure (6)(16), surface (16)(4)(22)(24), adsorption (31)(4)(5)(25), rheology (10-11)(12)(13)(26)(27)(32), plasticity (30) (31), and chemistry (23)(3)(7) of attapulgite. Attapulgite is the principal mineral constituent (70 to 80%) of attapulgite clay as it is commercially produced in the Georgia-Florida area of the United States. As mined, this clay also contains 10 to 1S% montmorillonite, sepiolite, and other clays; 4 to 8% quartz, and 1 to 5% calcite or dolomite. (18) During processing, non-clay fractions are removed so that commercial products are enriched to 85 to 90% attapulgite. By wet processing (such as practiced in the

Jan 1, 1971

By Wisecarver D. W.

Today the longwall is getting increasing attention in the United States as an excellent way to mine coal. This is not to say it is the best way in every mine because conditions, capital costs, and markets may well dictate another method. However, operators with working longwalls are often showing preference by phasing out room-and-pillar sections and replacing them with longwall. In the United States there are about 90 longwalls in operating coal mines and the number is increasing. In Europe, 95% of underground coal mining is by longwall compared with only 5% in the United States. In the Western States about 25% of the underground coal mines use longwall mining. There is logic behind the increase in longwalling. Compared to room-and-pillar mining, straight single-pass longwall has important advantages that show up in underground coal mining in any part of the country.

Jan 1, 1978

By M. T. Smith

In a 2,000 square mile area of Polk, Hillsborough, Hardee and Manatee Counties in Central Florida is located one of the richest known deposits of the life-giving mineral, phosphorus. Under layers of sand and clay are found millions of tons of phosphate rock, best source of this element which is necessary to all forms of life - plant, animal and human. Phosphorus is an irreplaceable ingredient in all complete plant foods, and more than 90% of Florida's vast production goes to enrich the croplands of the United States and many other areas of a hungry world. In addition to this, it has wide industrial use in the manufacture of many products - detergents, baking powder, carbonated beverages, steel, matches, munitions, glass, insecticides, dyes, water softeners and innumerable others. Not only does phosphorus make life possible for us - it also helps us to live longer and better.

Jan 1, 1962

By Kailash Narayan

Atlantic Richfield Company began operating a commercial uranium solution mining project in April, 1975 in Live Oak County, 10 miles southwest of the town of George West (Figure 1). The operation is designed to produce 250,000 pounds of U303 per year and is jointly owned by Atlantic Richfield Company, Dalco and U. S. Steel. The proprietary process employed in this operation consists of injecting an alkaline leaching solution into the ore-bearing formation through a pattern of injection wells. The uranium-bearing solution is then removed through producing wells using submersible pumps in central production wells. The produced solution is pumped through a pipeline to the plant area where the uranium is extracted. The barren solution is refurbished and returned to the pattern area for reinjection. The injection field and plant site are located in the drainage of Spring Creek, a small intermittent stream tributary to the Nueces River. Land use in the area is primarily agricultural -- cattle ranching and farming -- but several producing gas fields are present in the areas as well.

Jan 1, 1976

"During his presentation at the 2016 George A. Fox Conference about the history of public-private-partnerships (PPP) in the tunneling and underground construction industries in New York, Vincent Tirolo, Jr., told a story about how, as a young engineer in the late 1960s, he and others pooled money to purchase a calculator for $75 that had the ability to perform sine and cosine functions. That was a big deal in those days and would make their job much easier. Oh how far things have come. Tunnel and underground construction engineers can now virtually map out and plan entire projects before the first shovel ever breaks ground. And the machines that are used to build the tunnels have advanced in ways that could not have been imagined 50 years ago.The calculator is just one example of innovation in the industry and on Jan. 26, more than 400 industry professionals attended the George A. Fox Conference at the Graduate Center of New York (CUNY) to learn more about the next innovations, new tunneling technologies and what the future might hold for the industry. The conference included sessions on contracting models, rescue and fire life safety and new technological developments as well as an international project spotlight presentation from Nasri Munfah about the Eurasia Tunnel, connecting the European and Asian sides of Istanbul, Turkey.The project, also known as the Istanbul Strait Road Tube Crossing project, was named the 2015 Major Tunneling Project of the Year by the International Tunneling and Underground Space Association.The tunnel boring work for the 3,344-m (11,000 ft) long tunnel under the Istanbul Bosphorus Strait was completed in August, heralding a new era in tunneling.Tunnel boring work was launched in April 2014 with a ceremony with then Prime Minister Recep Tayyip Erdogan in attendance. The work was completed on Aug. 22, 2015 with Prime Minister Ahmet Davutoglu participating in the ceremony."

Apr 1, 2016

By Chee S. Theng

As the 2018 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2018 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 344. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2018 Transactions consists of a total of 59 technical papers, encompassing all 25 papers published in 2018 in the Technical Papers Section of Mining Engineering (Vol. 70) and all 26 papers published in 2018 in Minerals & Metallurgical Processing (Vol. 35). Additionally, this volume contains 8 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our Publications staff. As the 2018 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume. The new year brings an exciting change. The publication of Transactions will cease with this volume. Instead, our Minerals & Metallurgical Processing journal has the new name of Mining, Metallurgy & Exploration (MME), and Transactions as well as the Technical Papers Section of Mining Engineering are incorporated into MME. The journal is published in partnership with Springer Nature, and all SME members have free electronic access to the journal.

Jan 1, 2018

By M. Birdsell

"Sustainable long-term restoration requires adequate planning and preparation, implementation, and measurement goals to monitor success associated with restoring sites to pre-disturbance levels of ecological health. The Buckhorn Mountain Mine riparian habitat restoration project has been a multi-year endeavor with a variety of restoration techniques implemented by Kinross Gold/Crown Resources Corporation. INTRODUCTION The Buckhorn Mountain Mine procured mitigation lands during the permitting process to be set aside for long-term restoration. A portion of this mitigation land included three aquatic habitat mitigation parcels; a spring and wetland complex and two stream and riparian corridors. These properties were historically used for agriculture purposes and livestock grazing. During initial permitting, habitat monitoring and mitigation plans were created to help guide restoration, and provide measures for success. Various techniques and adaptations have been implemented on the properties since 2007, and continued efforts are being implemented annually to ensure the long-term success of the project. Field measurements are collected annually to ensure mitigation objectives are being met, and provide opportunity to modify restoration efforts when necessary. MATERIALS/METHODS Restoration efforts have included implementation of several methods including livestock exclusion, treatment of state and locally listed noxious weed species, installation of regionally sourced riparian plant species and local stock willow cuttings. Annual mechanical and herbicide treatments for noxious weeds have been conducted annually. Efforts to control reed canarygrass (Phalaris arundinacea) have been implemented since 2013; methods include mechanical and herbicide treatments. A combination of methods has been employed to help aid restoration of native species within the riparian corridor, and increase survival of planted species, including weed matting and browse barriers to aid riparian planting success. Instream planting of local stock willow have also been employed to increase stream vegetative cover and provide long-term bank stabilization. Most recently, a perched culvert near one of the properties has been replaced with an aquatic life passable culvert designed to aid in the upstream migration of fish species into the stream system. Efforts to provide increased fisheries into upstream portions of the system and aid in restoration of stream bed and bank have been employed to increase the ecological value downstream of the replacement. In addition to efforts completed by the client to provide restoration efforts, a local non-profit organization, in conjunction with the client, installed beaver dam analogues (BDAs) in the fall of 2014. These structures are intended to raise water levels along stretches of incised channel in an attempt to flood historic off-channel floodplain"

Jan 1, 2016

By Paolo M. Brion, Z. Bade Sozer

"The Bypass Tunnel has high head conditions ranging from a minimum of 600 feet (183 m) under the Hudson River to a maximum of 875 feet (267 m) on the west side. The ground cover ranges from 425 feet to 900 feet (130 to 274 m). A two-pass lining is designed for the Bypass Tunnel. The bolted, gasketed precast segments carry the temporary hydrostatic and permanent ground loads. After the tunnel is put into service, the design assumes that the final lining, which varies from reinforced concrete to reinforced concrete with steel interliner, will carry the permanent hydrostatic loads. The design head for the segments is assumed at 775 feet (236 m), and the internal operating pressure head is around 1,200 feet (366 m). This paper discusses the design hydrostatic head and different load conditions considered for the segments, the load sharing between the segments and final lining, and the means employed to control water and hydrostatic pressure. PROJECT BACKGROUND The Rondout-West Branch Tunnel (RWBT), a segment of the Delaware Aqueduct, was built from 1937 to 1944 and provides about 50% of New York City’s total water supply. Monitoring and tunnel operations have shown that the RWBT is leaking up to 35 million gallons per day (MGD) (132.5 million L/day). In particular, two locations have been identified as areas of concern: Roseton and Wawarsing, as shown in Figure 1. The Wawarsing reach of the aqueduct will be repaired with an extensive grouting program when the RWBT is unwatered. However, because of the extensive nature of the leakage in the Roseton area, a Bypass Tunnel will be constructed to divert the flow around this area."

Jan 1, 2016

Selective Flocculation process development generally involves single mineral flocculation tests to identify the appropriate polymer and experimental conditions for achieving the desired selectivity. Invariably the selectivity predicted on the basis of such tests is not realized when mixed mineral tests are conducted. A systematic experimental investigation revealed that adsorption of the polymer on various substrates is critical to selecting the suitable flocculent. Simultaneously, a mathematical model was developed to predict the overall process efficiency with a given polymer. In this paper, results of these efforts to scientifically design a suitable selective flocculation process are presented.

Jan 1, 1991