Search Documents

By W. J. Schuster

Safety in coal mines depends largely upon adequate training of the foreman. Although management must provide modern and safe equipment and at all times keep mines in first class condition from a safety viewpoint, final results will be determined by the quality of supervision. HANNA COAL CO., Division of Pittsburgh Consolidation Coal Co., operates three large underground mines in eastern Ohio. The section of Pittsburgh No. 8 coal seam in which these mines are located varies in thickness from 52 to 64 in. It is immediately overlain by a stratum of shaly material 12 to 15 in. thick locally known as draw slate, which is structurally very weak and which disintegrates rapidly upon exposure to atmosphere. Immediately above the draw slate as it is normally found is a band of extremely high ash material 6 to 12 in. thick known as roof coal or rooster coal, and above this is a stratum of conglomerate material varying from 4 to 10 ft in depth. Overlying the conglomerate is a relatively thick stratum of limestone, the first stable material above the Pittsburgh coal seam in eastern Ohio. With the method of full-seam mining that has been adopted, draw slate is shot down, loaded with the coal, and removed in the preparation plants. The roof coal then becomes the permanent roof. The major problem in mining the No. 8 seam in eastern Ohio is control of the roof. Since the strata above the draw slate contains no material with a structure firm enough to provide self-support, the roof begins to sag in a relatively short time after the coal and draw slate have been removed. The problem thus becomes one of getting temporary safety posts under this roof as quickly as possible to prevent a break or separation from occurring either in the roof coal or in the conglomerate above it. Haulage System The Pittsburgh No. 8 seam in eastern Ohio is relatively level, with only minor local dips. Throughout the Hanna Coal Co. mines, entries are generally 12 ft wide. Rooms are driven on a 60" angle on 30-ft centers and are 22 ft wide. No attempt is made to extract the 8-ft pillars between. The entire length of main line haulage is gunited in one mine, and a major portion in another. Two of the mines have single-track main haulage roads with passways. The third, a new mine, is double-tracked, and the roof is supported by steel crossbars, 60 lb or heavier, spaced on 4-ft centers and lagged. In recent years timbering on main line and secondary haulage roads has been accomplished by one of two methods: 1—crossbars are supported on a small section of post set in a hitch hole in the rib, or 2—or a hole is drilled in the rib about 12 in. below the roof, of sufficient depth to fasten securely a short length of 40-lb rail, the bottom of the rail facing the roof, on which a short post is set directly under the crossbar. At present the hitch-hole timbering method is favored. At two of the mines the main line haulage locomotives are 26-ton, 8-wheel units. These locomotives are of the axleless type, each wheel being individually mounted on the frame. The motorman's compartment is encircled by 3-in. armor plate for the protection of the occupants. At the third underground mine conventional 15-ton locomotives are being used. However, these locomotives have been completely rebuilt in the company's shops. Equipment has been streamlined and quarters have been provided for two people, who are protected by heavy steel plate in much the same way described above. This modernization program has been completed on all secondary haulage locomotives at the three mines, and the company is well on the way to similar equipment of the 6-ton section locomotives. The following additional features have been included in their modernization: 1—additional support for the motors to prevent their falling to the middle of the track and derailing the locomotives should a break occur in the suspension bar support; 2—installation of additional bracing to prevent brake rigging from becoming displaced and causing derailments; 3—enclosure of all electric wiring in conduit or raceway; 4—provision of an enclosed compartment for the storage of re-railers, jacks, and other equipment, so that they need not be carried on the outside of the motor; and 5—redesign of the end of the locomotive opposite the operator's compartment to prevent anyone's mounting from that direction. It is interesting to note that some

Jan 1, 1955

By G. B. Misra

While investigating on the aerodynamic resistance of airways supported with peripheral timber sets, at regular intervals, the following theoretical equations were developed by the author to estimate the resistance coefficient of such airways: [ ] for S < 1, where f is Darcy-Weisbach resistance coefficient of the airway, C is modified drag coefficient of the supporting member, D is equivalent diameter of the bare airway, 8 is ratio of the approach velocity over the sets to the average velocity of the bare airway, A is cross-sectional area of the bare airway, a is projected frontal area of the sets, A., is cross-sectional area of the air stream at the vena contracta inside the set, S is spacing of the sets, f, is resistance coefficient of the bare airway, l is length of aerodynamic influence of sets, p is perimeter of the bare airway, p, is setted portion of the perimeter of the bare airway, pe is unsetted portion of the perimeter of the bare airway, and P shielding factor. The equations were verified experimentally in a model rectangular airway supported with one- (bars), three-, and four-piece sets of square-section timber of three different sizes and were found to hold true. The work has been further extended to one-, three-, and four-piece sets of round timber of 2.6, 3.2, and 3.8 cm diam with the same experimental set up. Tests have been carried out for spacings of 25, 50, 75, 100, 150, and 200 cm over a regime of flow defined by the Reynolds number (with respect to the equivalent diameter of the bare duct) ranging from about 1.5 X 106 to 5 X 106 using the same experimental techniques. The values of f are calculated in the manner indicated in [Ref. 1]. Unlike with square-section timber, the resistance coefficient f of the airway setted with round timber shows a distinct variation with the Reynolds number of flow. This conforms to observations made by Sales and Hinsley.2 In order to have a comparable value of f for all types of sets with all sizes of timber, it was necessary to select the value of f at a fixed Reynolds number of flow. Since f is chiefly a function of the drag coefficient of the sets, the appropriate Reynolds number RE is that with respect to the diameter of timber in the set. Considering the diameters of timber used and the regime of flow over which measurements were made, f was chosen at a value of RE = 20,000 in all cases. The f vs. S curves are maximal in nature and in conformity with theory, the f vs. 1/S curves are straight lines up to a value of S = 1 beyond which they show a distinct flexure. The observed values of 1, the length of aerodynamic influence of sets, agree with the relation 1 = 42 e, developed for square-section timber sets, thus suggesting that the shape of timber has little influence on the length of aerodynamic influence. The value of the modified drag coefficient CD for round timber was calculated in the same way as for square timber in Ref. 1, taking the contraction factor Z = 1.5 for round-edged constrictions. CD has an average value of 0.96 with a standard deviation of 6.08% as compared to the free stream drag coefficient of 1.2 at RE = 20,000 for long cylindrical obstructions The shielding factor [ ] is plotted against S/1 in [Fig. 1]. The curves are more or less independent of the size of timber, but are different for the different types of sets, possibly due to their different degree of symmetry. Values of f calculated by the author&apos;s [Eqs. 1 and 2], using experimental values of CD&apos; and [ ] and taking I = 42 e, are plotted in [Fig. 2] against experimentally measured values of f for different types of sets with different sizes of round timber. The values agree closely with a standard deviation of only 5%, thus establishing the veracity of the theoretical equations developed by the author for round timber as well. A comparison was made between the Xenofontowa4 equations (the only other reasonable relations available for the estimation of the resistance coefficient of supported airways) and the author&apos;s [Eqs. 1 and 2] by comparing in [Fig. 3] the values of the resistance coefficient f computed by the Xenofontowa relations with those experimentally measured by the author. In order to make

Jan 1, 1975

By C. S. Barrett, A. Smigelskas

There have been no publications of the deformation and recrystallization orientations of the metal beryllium, yet pronounced textures would certainly be anticipated since it is close-packed hexagonal in structure. Having an axial ratio approximately that of magnesium, beryllium probably deforms by nearly the same slip and twinning mechanisms that operate in magnesium, and the textures are likely to be similar or but slightly different from the magnesium textures. In the tests reported below this is found to be the case; the textures are found to differ from those of magnesium only in the details of the scatter from the average orientation. This report covers not only samples rolled at room temperature, but some rolled at elevated temperatures. Since magnesium has been suspected by some investigators of altering its crystallo-graphic deformation mechanism at elevated temperatures, it was considered possible that beryllium might do so and alter its textures accordingly. No pronounced alterations were found, however. Unfortunately, the theory of deformation textures is not in a state of development that permits one to deduce the deformation mechanism from a knowledge of the textures, which means that the similarity of textures at different rolling temperatures, reported here, cannot be taken as definite evidence that the deformation mechanism is actually the same at all temperatures. The general similarity of the deformation textures of magnesium and beryllium also extend to the recrystallization textures of the two metals, judging by the pole figures for recrystallized sheet presented in this report. Samples were prepared in the form of composite sheets made up of small pieces stacked in a pile. Each piece was trimmed with scissors so that an edge was parallel to the rolling direction, dipped in paraffin, and assembled into the pack by aligning it under the cross hair of a microscope. As the desired orientation was obtained on each piece it was secured in place by touching with a hot wire to melt the paraffin. A stack of ten or fifteen pieces was built up in this way, then trimmed to the shape of a T; the portion to be X rayed was then etched to the shape of a wire about 0.045 in. diam with 6N HCl. This method of shaping the sample is a modification of that used by Bakarian on magnesium.&apos; The absorption of the rays in the sample was so slight that it caused no difficulty in interpreting the films. Exposures were made with a 0.030 in. diam pinhole, using molybdenum radiation (40 kv, 25 ma, Type A film at 5 cm, 2 to 3 hr exposures). With the recrystallized specimens it was found necessary to oscillate the specimen so as to reduce the spottiness of the lines. A range of oscillation of 5" was SUB- cient to produce reasonably satisfactory patterns, though the quality was somewhat inferior to that of the deformation texture patterns, and only two degrees of intensity were read from the arcs on the films. Typical photo-grams for each of the deformation textures and the recrystallization texture are assembled in Fig 1. The pole figures were plotted in the usual way with the intensity of the various portions of the diffraction rings estimated by eye. Seven to nine films were made of each sample and each was carefully read in plotting the pole figures. Typical series included exposures with the beam normal to the rolling direction and at 11, 26, 41, 56 and 71" to the cross direction, plus two exposures with the beam normal to the cross direction, and at 11 and 79" respectively to the rolling direction. The rolling was in each case considered sufficient to develop the final texture: the reduction by cold rolling was 84 pct (from 0.0045 to 0.0007 in. thickness), following prior hot rolling in longitudinal and transverse directions and recrystallization; the reduction by hot rolling at 800°C was 90 pct (0.010 to 0.001 in.), following similar prior treatment; the reduction by rolling at 350°C was 88 pct (from 0.005 to 0.0006 in.) after similar prior treatment. The recrystallization texture was determined on a sample rolled at 350" to a reduction of 88 pct (0.0165 to 0.002 in.) after similar prior treatment, then mounted between steel strips to keep it flat and annealed at 700" in an atmosphere of argon. Discussion of Results The results of the X ray determinations are assembled in the pole figures of Fig 2, 3, 4 and 5 for rolling at

Jan 1, 1950

By J. D. Anthony

The Australian continent possesses significant reserves of a wide range of minerals, including bauxite, coal, copper, diamonds, gold, iron ore, lead, manganese, mineral sands, nickel, phosphate, silver, tin, uranium, and zinc. Australia&apos;s identified economic resources of many minerals are very large as indicated in Table 1. A sophisticated and highly experienced mineral industry is now an established feature of the Australian economy and Australia is the world&apos;s largest exporter of iron ore, alumina, mineral sands and refined lead and amongst the leading suppliers of many other commodities such as coal, lead and zinc ores/concentrates, nickel, refined zinc, tungsten concentrates and bauxite. The industry exports 70% of its production. This is reflected in the value of Australian mineral exports which have grown from about $200m in 1960/61, comprising 10% of total export receipts, to about $1265m or 29% of export income in 1970/71 to around $7061 representing 37% of Australia&apos;s total export income in 1980/81. Details of the more significant minerals are as follows: Japan (42.1%) USA (11.3%) ASEAN (6.3%) UK (5.9%) F.R. Germany (3.8%) Republic of Korea (3.4%) New Zealand (2.6%) Also see Table 2. AUSTRALIA&apos;S MINERAL RESOURCES POLICIES Federal and State Governments&apos; Responsibilities Australia has a federal system of government comprising six States, a self-governing Territory and a Federal Government. Under the Australian federal system the Constitution sets down the powers of the Federal Government. All powers not assigned to the Federal Government in the Australian Constitution reside automatically with the States. Certain of these broad powers result in the Federal Government having a significant influence on resources development. For example, in being responsible for economic management, the Federal Government&apos;s fiscal and monetary policies have an important effect on industry as well as on State finances. In particular, the taxation regime employed by the Federal Government is of direct importance to decision-makers in the resources industry. The Federal Government is responsible also under the Constitution for external trade matters; and international trade and commodity matters are increasingly important in Australia&apos;s international relationships. Foreign investment is another area where the Federal Government has a role to ensure that national interests are protected. This foreign investment power flows from the Federal Government&apos;s control of foreign exchange movements into and out of Australia. However, before enlarging on these and others of the Federal Government&apos;s powers and policies, it should be emphasized that the State governments, by virtue of their wide powers to regulate matters within their own boundaries, are more directly involved in the day-to-day administration and regulation of mining operations. For instance, the powers of the State governments include the responsibility-for the granting of exploration rights and mining leases, the approval of mining operations and the levying of royalties and other like charges. Administrative arrangements covering the granting of minerals and petroleum exploration and development titles vary from State to State. Before development rights are granted, State governments consider environment protection and rehabilitation aspects of development proposals. The provision of infrastructure within State borders is a matter primarily of State government responsibility. It is usual practice in Australia for State governments to construct and operate infrastructure services such. as railways, ports and electricity generation and transmission. The States may also provide certain public services such as electricity. and water, port and loading facilities, communications, health and education services which form part of the infrastructure of mining operations. In remote areas the mining companies themselves usually are expected to provide much of this infrastructure. However, the Federal Government is primarily responsible in some fields, such as telecommunications and parts of the railways network. State governments carry out preliminary exploration and geological mapping and some are directly involved in the mining of coal for power generation. The Federal Government&apos;s responsibilities in addition to economic management, taxation, international relations, foreign capital and investment, include regulation of exports, environmental matters and matters affecting the Aboriginals of the Northern Territory. FEDERAL GOVERNMENT POLICIES The continued sound development of the minerals and energy resources sector is regarded by the Federal Government as being of very great importance. However, the Government does not seek to participate directly in resource developments. It sees its role rather as that of establishing a sound economic and policy climate in which private companies can identify opportunities, seek out customers and marshall the necessary capital for the development of resource projects.

Jan 1, 1982

By K. E. Nelson

The effect of thorium and zinc variations on the strength and 100-hr creep characteristics of Mg-Th-Zn-Zr alloys was investigated. Optimum resistance to creep at 650° and 700°F are attainable within a certain range of thorium and zinc contents. This range does not conform to that which develops maximum tensile properties. RAPID advances have been made during the last few years in the development of magnesium alloys for elevated temperature applications demanding high resistance to creep. The beneficial effect of rare-earth metals on the creep resistance of magnesium alloys has been emphasized by a number of publications1-13 and such alloys are now in commercial production. The use of thorium as an alloying ingredient in magnesium was mentioned by McDonald and also in two Alien Property Custodian patent applications.10,17 The initial observation of Sauerwald that thorium contributes still higher creep resistance to magnesium than is attainable with rare-earth metals has recently been substantiated.&apos;" " In fact, it has been demonstrated that the useful temperature range of magnesium alloys is appreciably extended by the use of thorium. In all cases, it was observed that zirconium must be included in the alloys in order to render them fine grained and more readily castable. Several recent publications:2-27 indicate that a still further improvement in creep resistance and a further extension of the useful temperature range can be realized by the addition of zinc to alloys. The primary purpose of this paper is to present the results of a comprehensive study of the effect of zinc on the strength and creep characteristics of Mg-Th-Zr alloys. Compositions covering the range of thorium content from M to 6 pct and zinc content from 0 to 5 pct have been investigated. The creep characteristics at 650" and 700°F reported in this paper are based on results of tests of 100-hr duration. It is appreciated that creep tests of 100-hr duration might not yield adequate data for design purposes for parts with much longer expected life. However, for the purposes of the present discussion, it is felt that the combination of stresses and temperatures used in the 100-hr creep tests have yielded a clear representation of the compositional variation of creep resistance at the temperatures investigated. Creep tests of 1000-hr duration are now in progress on a few of the most promising alloys. Preparation and Testing of Alloys The alloys studied in this intensive investigation were prepared in 25 lb capacity mild steel crucibles. The thorium, zinc, and zirconium were alloyed and poured as described in earlier publications The thorium was introduced into the melt in the form of a Mg-Th hardener," the zinc added in the metallic form, and the zirconium alloyed in the form of the commercial hardener containing magnesium and 30 to 50 pct Zr.10, 26 Fluxing practices for melting and refining were the same as for magnesium-rare-earth metal-zirconium alloys. The melts were sampled for analytical determinations and poured into separately cast 1/2 in. diameter standard tensile bars. The test bars were given a precipitation treatment of 16 hr at 600°F in laboratory furnaces. It has been shown by other tests that a high temperature solution treatment followed by an aging treatment is unnecessary for the development of optimum properties in Mg-Th-Zn-Zr alloys. The selection of 600°F as the aging temperature was based on an attempt to achieve metallurgical stability without coalescence of the undissolved phases and the attendant loss in strength. The thorium, zinc, and zirconium contents of each melt were determined chemically. The zirconium contents are reported in two parts, "soluble" and "insoluble," referring, respectively, to the portions present in the alloy which are soluble and insoluble in dilute HCl acid. Distinction is being made between these two components of the zirconium content in the alloys because it has been found that only that portion of the zirconium content which is soluble in dilute inorganic acids affects the structure and properties of the alloys. The usual impurities consisting of copper, iron, manganese, and nickel were determined spectroscopically. The analysis for each melt is listed in Table I. A description of the methods of tension and creep testing has been detailed in earlier papers. The tests were performed with the cast skin re-

Jan 1, 1954

By R. E. Hudrlik, G. W. Preckshot

The diffusion coefficients of silver from solid silver in molten lead were measured to within ± 0.8 pet in a columnar type diffusion cell ower, the temperature range of 326° to 530°C. Fick&apos;s law describes the process up to 530°C where the laminar mechanism appareltly breaks down. These is negligible resistance at the interface as shown by mathematical analyses. The diffusion coefficients are found concentration independent. IT would seem that diffusion in liquid metals would be free of such effects as molecular structure, dissociation. polarization. and compound formation. This view was taken by Gorman and preckshot in their study of diffusion of copper from solid copper into molten lead. They reported diffusion coefficients which were independent of the concentration over the range of 478° to 750°C. They found that the Stokes-Einstein equation with constant radius of the diffusing specie represented the diffusion data better than Eyring&apos;s rate theory equation and Sheibel&apos;s correlation. The radius of diffusion was found to be that of the doubly charged copper. There appeared to be no resistance across the solid-liquid boundary. In the present work the diffusion coefficients for silver in liquid lead were measured over a range of temperatures of 350° to 505°C. The solubility of silver in lead over the range of 303° to 630°C was also obtained. These results are compared with calculated or correlated values or with data in the literature. EXPERIMENTAL Procedure—The experimental equipment techniques and procedures were those reported in detail by Gorman and preckshot9 and will not be repeated here. Measured values of WT, Co, A. L were obtained for various diffusion times and the diffusion coefficient was computed for the case of no resistance at the interface9, 11 by: WT/CoAL = 1- 8/p2 n=1 1/(2n - 1)2 exp[-(2n - 1)2p2 Dt/4L2] [1] or where there was resistance at the interface by: WT = 1- ?n=1 2h2/ap2L [sxp [-Dan2t]/[(h2 + an2) L + h] The roots an are those of the transcendental equation3 tan (an L) = Iz/cun. The diffusion coefficient is that defined by Hartley and Crank.7 The total silver in the lead cylinder and equilibrium slug was determined by a cupellation technique&apos; with proper correction for losses. Analysis of known samples showed that this method is surprisingly accurate. The amount of silver in the lead adhering to the silver cylinder was obtained in the same fashion as shown by Gorman and preckshot.9 The small errors involved in this determination are not critical since the silver in this adhering lead layer is only 3 to 15 pet of the total diffused. Materials—Electrolytic silver containing 99.9+ pet Ag obtained from General Refineries of Minneapolis, Minn. was used for all but runs 7 and 8. For the balance of the runs this silver was reduced with hydrogen at 1100°C and its oxygen content was found to be about 0.017 pet. For the runs. 7 and 8, phosphorous-reduced silver of the same purity was obtained from Handy and Harman Co. of Chicago, Ill. The densities of the phosphorus-reduced silver and the hydrogen-reduced electrolytic silver were 10.484 and 10.487 g per cm3, respectively. These values agree with those reported for pure silver. Silver which was reduced at 900 C had an average density of 9.998 g per cm3, indicating porosity. This silver was used for a number of runs which were not tabulated in Table I. These are indicated by crosses on Fig. 2. The 99.999 pet Pb was obtained from the National Lead Co. Research Laboratory of Brooklyn, New York. DISCUSSION OF RESULTS The diffusion and solubility results are reported in Table I for eleven runs using either phosphorus-reduced electrolytic silver or hydrogen-reduced silver at 1100° C. The solubility data shown in Fig. 1 show the excellent agreement with that reported by Heycock and Neville.8 The data of Friedrichs5 apparently are in error. The experimental solubility data of this work are reported to 0.3 pet. The experimental diffusion coefficients computed from Eq. [1] are reported within 1.2 pet of the mean and are plotted in Fig. 2. These are expressed within +0.8 pet of the experimental values over the entire temperature range by: D= 8.26 x 10 -5 e-1925/RT . [3] There appears to be little difference due to the

Jan 1, 1961

By T. Watanabe, S. Karashima, H. Oikawa

Creep tests of a! iron and its solid-solution Fe-Mo, Fe-Co, and Fe-Si alloys with bcc structure were conducted under constant stresses in ferromagnetic and paramagnetic temperature regions above 0.5T,(T, is the absolute melting temperature). It was found their high-temperature creep behavior changed in the vicinity of the magnetic transformation temperature, that is Curie temperature, TC. In the ferromagnetic region below the steady-state creep rates were lower than those expected from the extrapolation of the data in the paramagnetic region, the amount of decrease being affected by solute addition. Also, activation energies for steady-state creep were different in the two temperature regions. The observed changes were concluded to be due to the effect of ferromagnetism on diffusion. It is well-known that plastic deformation of metals and alloys in the temperature region where mobility of atoms becomes high enough is controlled by atomic diffusion." Many experimental results394 on fcc and hcp materials have been reported to confirm this view. In bcc metals and alloys, not much basic investigation of creep deformation has been performed. In particular, experimental work on iron5-&apos; and its alloys, covering a quite wide temperature range is extremely scarce. On the other hand, the effect of ferromagnetism on diffusion has recently been demonstrated in a iron and its alloys;&apos; it has been made clear that diffusion rates in ferromagnetic temperatur~e region are significantly lower than those expected from diffusion measurement in the paramagnetic region. Therefore, it is concluded that the magnetic effect influences the high-temperature creep behavior in a! iron and in its alloys. The present authors have conducted creep experiments on a iron and its solid-solution alloys over a very wide temperature range, and have demonstrated the magnetic effect. A part of the result has already been reported elsewhere.26 In this paper, the experimental results will be described in detail. While the manuscript was in preparation, a similar magnetic effect on creep deformation of a iron was reported by Ishida . Though their experiments covered an extremely wide temperature range, the creep stresses varied from several thousand psi to several ten thousand psi with decreasing temperature. Consequently, it may be said that there remain some questions concerning their results. I) EXPERIMENTAL PROCEDURE The materials used in the experiments were pure iron and its alloys; they were prepared by vacuum melting (10"" mm Hg) electrolytic iron (99.9 pct), molybdenum powder (99.9 pct), ultrapure silicon, and cobalt pellet (99.5 pct) in alumina crucibles. The ingots were hot-forged to plates 10 mm thick and 50 mm wide, and then were hot-rolled at about 700°C into sheets 1 mm thick. Creep specimens, 5 mm in width and 15 mm in gage length, were machined from the sheets. They were annealed at temperatures which were well above their respective recrystallization temperatures. The chemical compositions of the metal and alloys are shown in Table I together with their heat treatments. High-temperature creep tests by the use of a lever-type creep testing machine were carried out in argon atmosphere under constant tensile stress. In order to keep &eep stress constant within about *0.5 pct, stress change due to specimen elongation was compensated by tensile force of a stainless-steel bellows which was inserted between the loading lever and lower specimen grip with the assumptions of a linear relationship between change in cross section and strain and uniform strain along the section. Beyond the limit of compensation by the bellows, small amounts of load were removed after appropriate strains. The testing temperatures were maintained to within i2"C of the reported values. Creep deformation was auto-graphically recorded at the upper (moving) specimen grip using a linear differential transformer which was held by a stainless-steel rod mechanically connected to the lower specimen grip. It was also directly measured with a dial-gage reading to -& mm. 11) EXPERIMENTAL RESULTS AND DISCUSSION 1) Creep Curves of a Iron and Its Alloys. Creep curves of a! iron, Fe-Si, Fe-Co, and Fe-Mo (<2 at. pct Mo) alloys usually consisted of three stages, that is transient (primary), steady-state (secondary), and accelerating (tertiary) stages. An example is illustrated in Fig. 1 for a! iron. However, in Fe-Mo alloys with more than 2 at. pct Mo, an inverse transient creepZ8 was observed as indicated in Fig. 2. The inverse behavior, which varied with the amount of molybdenum, may be due to the substructure* in the annealed specimen as was sug-

Jan 1, 1969

By G. A. Swanquist, E. M. Morales

INTRODUCTION The idea of water management and control at the Church Rock Mill operations began to take shape in February 1979. At that time, we were already investigating the feasibility of decreasing the fresh water requirements so that the solids would become the limiting factor in tailings impoundment utilization. The area for solution evaporation could be kept at a fraction of the normal requirements under the standard process of full water usage. The Church Rock Mill is an acid leach circuit followed by solids/liquid separation with thickeners in counter current decantation, and solvent extraction. Following the normal design of acid leach circuits, reuse of tailings solution was not incorporated in the original mill process design. INITIAL WATER CONTROL INVESTIGATIONS The investigations to decrease the fresh water requirements centered around modifying the grinding circuit from the present semi-autogenous grinding (SAG) mill in closed circuit with hydrocyclones, to open circuit grinding with a rod mill. The open circuit grinding with the SAG mill and rod mill in series had the potential of decreasing the water requirements for grinding and leach dilution by approximately 50% or 1.4 m3/min (300 gpm). The grinding pulp density would be maintained at 70 to 72% solids, and the leach dilution to 50% solids would be accomplished with acid tailings liquor recycle. In such a grinding circuit arrangement, the SAG mill would provide the primary or coarse grind, and the rod mill would be used for the fine grind. By the SAG mill and rod mill series grinding method of water control and other secondary water controls in various places downstream from the grinding circuit, the required necessary evaporation area was estimated at 120 acres of liquid surface. A second method of water control at grinding was investigated. A two-stage cyclone classification circuit appeared to have a good potential of achieving the same water reduction at a much lower capital and operating cost. However, in retrospect, this would not have been a viable method since a high slime recycle load would have been established hindering classification. The use of reagents to neutralize the acid tailings solution was not considered seriously at that time, since it would have materially increased operating costs, although it would have also allowed more tailings solution recycle and consequently, less fresh water usage. However, with the tailings solution deposition area available at that time, it was not then necessary to incur the high cost of neutralization. The control expected by the series grinding of semiautogenous and rod mills would have been sufficient to maintain a water consumption/evaporation equilibrium well in line with the available land area. IMPLEMENTATION OF NEUTRALIZATION OPERATIONS During the summer of 1979, the UNC Church Rock Mill experienced a tailings dam breach which resulted in a prolonged mill shutdown. Upon resumption of operations at the end of October 1979, tailings deposition was restricted to a small portion of the tailings impoundment area. Figure 1 shows the general tailings area and the limits of the present deposition area in the central part including the borrow pits. These borrow pits had been excavated to provide materials for tailings dam construction. Immediately after resumption of operations, it became evident that it would be necessary to control the quantity of liquid to be evaporated because of the small confined area available for tailings solution deposition and to maximize the deposition time in the tailings area. The water control required had to be exercised on a large scale, and to be in operation as quickly as possible. An obvious solution was to reuse the tailings liquor in mill process. Immediate steps were taken to install the necessary equipment for tailings neutralization on an interim basis. Anhydrous ammonia was selected as the primary neutralization reagent since it was the quickest system that could be placed in operation. Previous laboratory tests indicated fair results with ammonia neutralization. Such a system required a minimum of installed equipment and handling. INITIAL NEUTRALIZATION OPERATIONS Actual neutralization operations began on November 26, 1979. The raffinate solution which normally would have been discarded was pumped to a 3.7 m (12ft) diam by 4.3 m (14ft) tank for reagent contact, see Figure 2. At this tank, anhydrous ammonia was added directly from the tanker trailers and controlled at pH 7.0 nominally. Agitation was provided by air sparging. The neutralized product formed a highly viscous slurry in the grinding circuit which resulted in pumping and cyclone classification problems.

Jan 1, 1982

By M. Bevis, A. F. Acton, P. C. Rowlands

Defor~nation twinning and transformation twinning modes most likely to be operative in Fe-Ni and Fe-Ni-C martensites have been determined using a new theory of the crystallography of deformation t~inning.~ This analysis shows that potentially important conventional and nonconventional twinning modes1 have been omitted in previous analyses. Discussion is given on the relevance of the predicted twinning modes to the lattice invariant shear associated with the martensite transformation in steels and to anomalous deformation twinning in Fe-Ni-C martensites. THE two most important criteria which appear to govern operative twinning modes in metallic structures1 are that the magnitude of the twinning shear should be small and that the twinning shear should restore the lattice or a multiple lattice in a twin orientation. The latter criterion ensures that the shuffle mechanism required to restore the structure in a twin orientation is simple. These criteria have been adhered to in the prediction of twinning modes2"6 in bcc and bct single-lattice structures with axial ratios in the range y = 1 to 1.09 as, for example, encountered in martensite occurring in steels. Refs. 2 and 3 in particular consider the martensite transformation in steels and the twinning modes in these cases relate to transformation twinning, and hence the lattice invariant shear associated with the martensite transformation. The list of twinning modes which can be compiled from these sources is incomplete and the ranges of magnitude of shear considered could be unrealistically small, particularly in the case of deformation twinning. The latter consideration is supported by the fact that twinning modes with magnitudes of shear large compared with the smallest shear consistent with a simple shuffle mechanism have been established in, for example, the single-lattice structure mercury7 and the multiple-lattice structure zirconium.&apos; In addition the anomalous deformation twins reported by Ftichrnan4 to occur in a range of Fe-Ni-C martensites still remain unexplained. It is clear that a comprehensive analysis of twinning modes likely to be operative in martensite In steels is required. The results of the application of a new theory of the crystallography of deformation twinningg to these structures are presented in this paper. The theory has been used to determine all shears which restore the lattice or a multiple lattice in a new orientation with magnitude of shear up to a required maximum. The orientation relationships between parent and twinned lattices are not restricted to the classical orientation relationships of reflection in the twin plane or a rotation of 180 deg about the shear direction. PREDICTED TWINNING MODES Twinning modes which restore all or one half of lattice points to their correct twin positions will be referred to as m = 1 and m = 2 modes, respectively. These modes are the most likely to describe operative modes in single lattice structures. The bcc m = 1 and m = 2 modes which have magnitudes of shear s in the range s < 2 and s < 1, respectively, have been given10 and are reproduced here in Tables I and 11. Detailed discussion of the crystallography of these modes and cubic modes in general will be discussed elsewhere (~evis and rocker, to be published). The four twinning elements Kl, &,ql,7)2 as well as the magnitude of shear s are given for each twinning mode, and the twinning modes are given in order of increasing shear. Two twinning modes are given in each row of the tables, the twinning mode Kl, Kz, ql, q2 and the reciprocal twinning mode with elements Kl = K,, Ki = Kl, q: = q2, and 17; = ql. The m = 1 and m = 2 twinning modes which describe twinning shears with small magnitudes of shear and simple shuffle mechanisms in bct crystals with -y = 1 to 1.09 are given in Tables I11 and IV, respectively. On increasing the symmetry of the tetragonal lattice to cubic, that is making y = 1, all modes listed in Tables 111 and IV must reduce to crystallographically equivalent variants of the modes given in Tables I and 11, respectively, or become twinning modes with both shear planes as symmetry planes in the cubic lattice and hence not considered in Tables I and 11. With the exception of this last type of mode only those tetragonal twinning modes which reduce to modes 1.1, 1.2, 2.1, and 2.2 of Tables I and I1 are considered in Tables 111 and IV. For values of y in the range -y = 1 to 1.09 the tetragonal modes and the corresponding cubic twinning modes have approximately the same magnitude of shear. The twinning modes listed in Tables 111 and IV are therefore by the criteria given above the most

Jan 1, 1969

By R. M. Hudson, P. E. Perry

Weight-gain data obtained by nitriding low-carbon sheet steel in an amrnonia CNH,) atmosphere indicated that the process obeyed a parabolic rate law. The calculated actization energy for nitriding in the range 964" to 1268°F agreed reasonably well with published data. At 1358"F, rate data indicated that the activation energy decreased. Weight-gain data obtained by uszng mixtures of NH3 -Nz at 1268°F containzng jrom 10 to 100 zol pct NH3 also obeyed a parabolic rate law. The rate of &apos;nitriding increased with an increase in the NH3 content of the gas Mixture. It is well-known that steel heated in gas mixtures containing ammonia (NH3) takes up much larger quantities of nitrogen than steel heated in nitrogen, both gases having a total pressure of 1 atm;&apos; this phenomenon can presumably be attributed to the catalytic decomposition of NH3 on the steel surface to furnish nascent (monatomic) nitrogen. This process was studied bv Brunauer. Jefferson, Emmett, and Hend-ricks at furnace temperatures of 752" and 831°F2 using mixtures of NH3 in Hz. Englehardt and wagner3 reported that, at a furnace temperature of 914°F and under their experimental conditions, both nitriding and denitriding were controlled by the rate of gas-metal reactions at a steel surface rather than by the rate of diffusion of nitrogen in iron. The present study was undertaken to obtain information on the kinetics of nitriding low-carbon steel strip at higher temperatures so that practical rates for short-time strip-annealing treatments could be estimated. Variables studied included time: temperature, and NH, content in the annealing atmosphere. Mechanical and chemical characteristics of steel nitrided in this manner will not be considered in the present article. MATERIALS AND EXPERIMENTAL WORK The samples used were from a commercial low-carbon steel, 0.0244 cm thick, in the cold-reduced condition. The chemical composition of this steel is given in Table I. Panels were cut to 5.1 by 17.8 cm, degreased in toluene, and weighed just before treatment. Four specimens were nitrided under each of the experimental conditions. A study was made of the nitriding rate of steel in a 100 vol pct ammonia atmosphere, 740 mm pressure, at five specific temperatures within the range 964" to 1358°F. The nitriding rates of steel in ammonia-nitrogen gas mixtures containing 10, 18, 26, 50, and 100 vol pct ammonia, 740 mm total pressure, at 1268°F were also determined. All atmospheres used were dried by successively passing them through drying towers packed with soda lime and with Linde Molecular sieve Type 4A. Quoted gas compositions refer to those entering the furnace. Specimens were held in the constant-temperature zone of a vertical annealing tube furnace for times of 14, 3, 5, 10, or 15 min. Gas flow rates were maintained at 3.8 cu ft per hr, which was nineteen volume changes per hour for the system used. The rate of flow was selected to provide a high level of free NH3 for cracking on the steel surface where the ammonia gas is most effectively used as a nitriding agent. The vertical annealing tube furnace consisted of a Hevi-Duty tube furnace with a 2 1/2-in.-ID mullite ceramic high-temperature tube. The constant-temperature zone (controlled within 10°F) was about 10 in. long. After each specimen was degreased, a hole was punched in one end, for attaching the specimen by hook to a chain so that it could be lowered into or raised from the high-temperature portion of the tube by means of a power-driven winch. A stainless-steel access port with O-ring seals was connected by suitable glass-to-metal seals to the cool upper portion of the furnace tube. After the weighed specimen was placed in the access port, the furnace tube was evacuated to approximately 10"3 torr, and then the system was flushed thoroughly with the atmosphere under study. When the gas flow rate and constant-temperature zone of the furnace were established, the specimen was lowered into the constant-temperature zone. The atmosphere flowed from the top to the bottom of the vertical furnace tube and was then vented. For all these runs, during the first 3 min of the time the specimen was in the constant-temperature zone of the furnace the specimen was heating up to the tempera-

Jan 1, 1970

By James R. Holden, Frederick E. Wang

Through both single-crystal and powder X-ray diffraction methods, ten A6B23-type compounds have been confirmed to exist between lanthanides (A) (plus scandium and yttrium) and manganese (B); A = Y, Nd, Sm, Gd, Tb, Dy, Ho, Er, Tm, and Lu. The formation of a compound of this type is shown to he extremely atomic size-sensitive; hence it can be classified as a "size-factorH compound. The "enveloping effect", a geometrical consideration observed in its crystal structure, is proposed as the reason for the A6B23-type compound being size-sensitive. The approximate ideal geometrical ratio of the radii R/r is 1.31 while experimentally A6B23-type compounds have a radius ratio lying within the range 1.2 to 1.4. FLORIO t al.&apos; characterized the structure of Th6MnZ3 as fcc, space group Fm3m, with 116 atoms in the unit cell. Since then, a number of isotypic binary compounds, and recently Gd n,,&apos; have been confirmed to exist. The fact that strontium and barium form A6Bz3-type compounds with magnesium strongly suggested the possible existence of Ba6Liz3. However, investigation3 showed the compound Ba6LiZ3 to be absent. Since both strontium and barium are group 11-a elements and are therefore "open metals",6 the nonexistence of Ba6LiZ3 can hardly be explained satisfactorily by valence-electron considerations. On the other hand, the consistent atomic-radius ratio, (R/r),* observed for the known A6Bz3-type compounds,3 strongly suggests that the formation of compounds of this type is atomic size-sensitive. Therefore, one is tempted to explain the nonexistence of Ba6LiZ3 entirely on the basis of the atomic-size difference between strontium and barium. However, this approach is not entirely without objection. Atoms are not rigid spheres and are known to vary in size within certain limits.7 Since the atomic-radius difference between strontium and barium (0.07 to 0.09A) is within these limits, it is reasonable to assume that the size difference would have a negligible effect on the formation of Ba6LiZ3. This view is further supported by the fact that the radius ratio, R/r, in other known "size-factor" compounds is observed to range widely—for example, from 1.08 to 1.45 for ABz-type compounds (C15, MgCuz type)&apos; and from 1.37 to 1.58 for AB5-type compounds (D2d, CaZn5 type).g The present investigation was undertaken in order to find a more satisfactory explanation for the non-existence of Ba6LiZ3 and, consequently, a better understanding of the nature of the A6Bz3-type compound. The primary objectives are to confirm the previous conclusion3 that the A6B23-type compound is indeed a "size-factor" compound and subsequently to determine the atomic-radius ratio range in which the A6Bz3-type compound can exist. In order to achieve these objectives, stoichiometric A6Bz3 alloys, where manganese (B) was alloyed with various lanthanide elements (A), were selected for investigation. The atomic-radius ratios of lanthanide elements with manganese range from 1.26 for Lu/~n to 1.46 for Eu/Mn. This radius ratio range includes and exceeds the range of all previously reported A6Bz3-type compounds—1.32 for Th/Mn&apos; through 1.38 for Sr/Li. Furthermore, the atomic-size difference between successive elements of the lanthanide series in order of atomic number) is of the order of 0.01A (europium and ytterbium are exceptions). The series of lanthanon-manganese alloy systems is ideally suited to a precise determination of the limits of allowable atomic-radius ratio for A6Bz3-type compound formation. EXPERIMENTAL PROCEDURE The lanthanide metals, in ingot form, supplied by Michigan Chemical Corp. (St. Louis, Mich.) and Nuclear Corp. of America (Burbank, Calif.), were guaranteed by the suppliers to be at least 99.9 wt pct pure (traces of silicon, calcium, and other minor constituents present on occasion, not to be more than 0.05 wt pct) as shown by spectrographic analysis. Manganese metal, in polycrystalline form, was redistilled from the commercial, chemically pure grade and was analyzed to be at least 99.95 wt pct pure. In all cases, the atom ratio between the two elements in each charge was A (rare-earth meta1):B (manganese) = 6:23 and a constant weight, 3 g, of

Jan 1, 1965

By Roland J. Lapee

A history of the progress made in copper refining in Montana is presented. The casting furnaces and the newly rebuilt electrolytic refinery are descmbed and operating details are given. Experiences with various addition agents, effects of rernoval of chlorine from the electrolyte, and effects of separan on electrolyte and on copper deposit are discussed. Observatzons are made on the effect of various impurities in anode copper and behavior of thezr salts in electrolyte and in slime, on treatment of slime for removal of copper, and on electrolyte puriification problems. The improved method for production of starting sheets is described. Attention is given to new materials for construction and to improvement in matrials handling ad quality control. COPPER refining at Great Falls, Montana, dates back to 1892. The original plant produced 65,000 lb. of cathodes per day at a current density of 16 amp per sq ft. In this plant anodes and cathodes were handled to and from the cells by means of hand-operated chain blocks and were moved about the plant by hand trucks. Cathodes were melted in coal-fired, reverbera-tory furnaces, were charged by hand, and refined copper was dipped by hand and cast in iron molds. In 1916, a new, modern plant with capacity to refine 18 million Ib. copper per month was built. Two refining furnaces were built, and each was provided with a twenty-mold Clark casting wheel. In 1922, the furnaces were converted to the use of pulverized coal: in 1923, to the use of oil; and in 1928, to the use of natural gas. In 1926, the plant was enlarged 50 pct. The use of pulverized coal for refining copper at Great Falls was discussed1 in a paper presented at the Salt Lake City meeting of the Institute in September 1925. Also, a comparison of the use of various fuels in copper refining furnaces was discussed 2 in a paper presented at the New York meeting of the Institute in February 1932. Prior to 1943 the cellroom was operated with twenty-five 720-lb. anodes and 26 cathodes per cell. Four cathodes, each weighing about 165 lb., were produced from an anode. In 1943 the weight of the anode was reduced to 460 lb., and two cathodes, each weighing about 190 lb., were produced from an anode. In 1949, a Billet Casting Wheel for the production of 3 in. diam phosphor deoxidized billets was built. A paper, presented at the New York Meeting of the Institute in February 1956, describes3 this plant and operation. In the electrolytic refinery, production is controlled by variation of the current density. In 1956, germanium rectifiers on a separate electrical circuit were provided for the starting sheet section so that current density could be maintained at any desired figure. Also in 1956, a program of modernization and enlargement of the Electrolytic Copper Refinery was started. This program, when completed, will raise the capacity of the Great Falls Electrolytic Copper Refinery approximately 33 pct, to 33 million lb. of cathodes per month. Furnace capacity for melting cathodes and anode scrap is ample to take care of the increased production from the electrolytic refinery. This fortunate condition came about primarily as the result of the three following changes: 1) The furnaces were lengthened 10 ft in 1922 when the fireboxes were found unnecessary for burning powdered coal. 2) Furnace life, and hence furnace capacity, was increased by the successful efforts of the Copper Refinery staff to develop a method for sanding furnace side walls and roof. 3) The natural gas being used has a very low sulfur content. As a result, it is possible to reduce time spent rabbling and poling and thus greatly increase tons per furnace charge. TANKHOUSE AND TANKS The Great Falls Electrolytic Refinery is 535 ft long by 252 ft wide. The cells are arranged in four crane bays in which are operated seven 10 ton Whiting Cranes. The old cells are in groups of ten, with circulation of electrolyte through five cells in cascade and with aisles between the groups of ten cells. The new cells are nested in groups of sixteen with no aisles, are all on one level, and have individual circulation to each cell. Present plans call for 1792 commercial cells and 128 stripper cells. To reduce confusion during the construction period, and to use the cranes, cars, and other equipment already on hand, the cells in the rebuilt section were designed to have approximately the same inside dimensions as the cells in the old part of the

Jan 1, 1962

By J. Chipman, G. G. Hatch

One of the important functions of the iron blast furnace is the desulphur-ization of pig iron before it enters the steelmaking furnaces. However, the increasing concentrations of sulphur in the metallurgical coke, source of approximately 90 pct of the sulphur present in the blast furnace charge, and demands for higher rates of production within recent years have increased the need for greater desulphurization within the iron blast furnace. Furnace operators are beginning to look for desulphurizing agents other than blast furnace slag to accomplish the desired degree of desulphurization. A considerable amount of work has been done on desulphurization outside the furnace with soda ash, calcium carbide and various synthetic slags. Whether the desulphurization of pig iron is accomplished wholly inside the furnace or partly inside and the remainder outside, will be determined by the economics involved. Regardless of which is the case, it is believed that it is necessary to have a better understanding of the physical chemistry of desulphurization by blast furnace slags. To this end, it is the object of the present investigation to attempt what is believed to be the first equilibrium study of the distribution of sulphur between liquid pig iron and a wide range of blast furnace slag compositions. Review of Literature There is a considerable amount of information in the literature concerning the desulphurizing power of iron blast furnace slags, the solubility of various sulphides in the slags, and the effect on desulphurization of temperature, of elements dissolved in the liquid iron, and of viscosity. However, there is nothing to indicate that the equilibrium distribution of sulphur between liquid iron saturated with carbon and iron blast furnace slags has been studied experimentally. Wentrupl has made probably the most detailed study of the desulphurization of pig iron to date. He considered that there are three distinct aspects involved, namely: 1. Desulphurization within the blast furnace (by lime and manganese). 2. Subsequent desulphurization by manganese. 3. The effect of subsidiary reactions on the desulphurization by manganese. The experimental work carried out by Wentrup was devoted mainly to obtaining a better understanding of how desulphurization by manganese was accomplished in the mixer and the ladle. Particular attention was given to the part played by carbon, silicon, and phosphorus associated with manganese in the iron, and the effect of temperature on desulphurization. The experimental results indicated that desulphurization by manganese is purely a process of crystallization of manganese sulphide. The addition of silicon to iron melts containing 3.5 pct carbon and less than 0.5 pct manganese had no noticeable effect on desulphurization, but with 1-2 pct manganese the silicon additions improved the desulphurization. Additions of phosphorus also resulted in improved desulphurizati011 by manganese, but the effect was not as marked as in the case of silicon. It was also found that desulphurization by manganese was further improved by lowering the temperature. In order to explain desulphurization inside the blast furnace, Wentrup considered the system iron, sulphur, calcium, oxygen, manganese. (silicon). The distribution of sulphur between the metal and slag was represented by the following equation: (SS) _ (S)Fe + (S)Ca + (S)Mn .... [S] = [s] [1] The parentheses and the brackets represent the equilibrium concentrations in weight per cent of the slag and metal constituents, respectively. Since FeS D (FeS) _ (FeS) (S)Fe LfeS - [FeS] [S] [2] (CaO) + S e (FeO) + (S)Ca _ (FeO)(S)Ca. (S)Ca _ (CaO) Kl = (CaO)[S] [S] ~K1(FeO) [3] Mn + S D (S)Mn (S)Mn (S)Mn K&apos; = [MnpT "1ST = *lIMnJ !4) Substitution of Eq 2, 3, and 4 into Eq 1 resulted in if = L- + *> (Sol + K^ (S) [51 Eq 5 was used to calcu1;lte -f^j and [S] at 1480°C for slags containing 30-50 pct lime, 0.1-2.5 pct iron oxide, 0-26 pct silica, 2 pct sulphur and iron analyzing 1.5 pct manganese. The value for LFaB at 1480°C was found to be equal to 4.5, based on the experimental work of Bardenheuer and Geller.2 The results of the calculations are shown in Table 1. Although the slags are hypothetical and do not represent the range of compositions found in ordinary blast furnace practice, the calculations indicate that lime is effective in controlling desulphurization only if the iron oxide and silica contents of the slag are kept low. Schenck3 did not claim K1 to be a true equilibrium constant, but an empirical value which varied with the silica content of the slag.

Jan 1, 1950

By D. J. Mack, R. E. Reiswig

Six examples of the peritectoid transformation were selected from the literature and studied by the method of isothermal transformation. The kinetics and mechanisms of five of the examples are presented as TTT diagrams and photomicrographs. The exist-enc- of a peritectoid in the sixth case is doubtful. ALTHOUGH the peritectoid transformation per se has been known for many years, no precise published data exist concerning the kinetics or mechanisms involved in transformations of this type, except for the brief treatment by Rhines, et al. 1,10 Bearing in mind the fact that investigations of recent years are uncovering more and more peritectoids and suspected peritectoids, a thorough study of the well-established peritectoids appeared to be in order. It was for this reason that a study of the kinetics and morphological mechanisms of six binary peritectoids was undertaken. The six peritectoids selected from the literature for study were those reported at 7.02 wt pct Al-Ag, 26.0 wt pct Sb-Cu, 30.5 wt pct Sb-Cu, 32.3 wt pct Sn-Cu, 8.35 wt pct Si-Cu, and 21.2 wt pct Al-Cu. These selections were based on availability and purity of components, ease of preparation and heat-treatment, and estimated reliability of the available equilibrium diagrams in the regions of interest. EXPERIMENTAL PROCEDURE The alloys used in this investigation were induction melted in electrode-grade graphite and chill-cast in cast-iron split molds. In all cases, the alloys were so brittle that they could easily be broken into samples weighing 1 or 2 g. Chemical analyses showed that the alloys used were close to the respective peritectoid compositions reported in the literature and that the impurity levels were low in all cases. Metallographic examination showed uniform distributions of phases in all samples, indicating uniformity of composition in the samples studied. Isothermal transformation studies were carried out in fused-salt media, using the familiar inter-rupted-quench method. Uniformity of temperature in the salt baths was maintained by continuous stirring with a stainless-steel agitator. On the basis of actual observations of the temperature fluctuations, the estimated temperature control was + 10C for the Ag-Al and Cu-Sb alloys and ±30C for the Cu-Sn, Cu-Si, and Cu-Al alloys. The accuracy of all temperature measurements was estimated to be ±1°C. It was found necessary to mount metallographic specimens of the Ag-Al alloy in cold-curing methyl methacrylate, since the temperatures encountered in mounting in bakelite or lucite caused an appreciable degree of transformation to the ß phase. For the other alloys, wood-flour-filled bakelite mounts were used to avoid extraneous X-ray diffraction lines during the later examination of the metallographic specimens on a Norelco Geiger-counter d if f r ac tomete r. In the X-ray diffraction procedure, agreement between the published diffraction patterns and those obtained in this study was good. This was particularly important for phase identification, since the literature contained little in the way of micrograph description in some cases. Etching of the silver-aluminum alloy for metallographic examination was done by swabbing with either of the following reagents: 1) 10 g CrO3, 1 g (NH4), SO2, 0.5 g NH4NO3, 100 ml H2O, or 2) 10 ml NH4OH, 1 ml 20 pct KOH, 4 ml 3 pct H2O2, 5 ml H2O. The other alloys were etched with the usual bichromate etchant: 2 g K2Cr2O7, 1.5 g NaC1, 8 ml conc. H2SO4, 100 ml H20 (swabbed vigorously). EXPERIMENTAL RESULTS A) The Ag-Al peritectoid at 7.02 wt pct Al— The phase equilibrium involved in this peritectoid is shown in Fig. I.2 The phase boundaries in the vicinity of the peritectoid were most comprehensively established by Hume-Rothery, et al,3 who placed the equilibrium temperature at 448 °C and the equilibrium compositions of the a ß&apos; and y phases at 6.11, 7.02, and 7.24 wt pct Al, respective The alloy used in this study analyzed4 6.95 wt pct A making it slightly hypoperitectoid according to the accepted equilibrium diagram. The rate of the transformation a+ y — ß&apos; varies rapidly with degree of undercooling below the equilibrium temperature, passing through a maximum in the vicinity of 350°C. Thus the TTT dia-

Jan 1, 1960

By D. S. Tomalin, D. F. Stein

The effect of reducing oxygen to low concentrations on the fracture of high-purity iron single crystals has been examined at 78° and 20°K. It is found that iron single crystals grown by the strain-anneal method usually contain a few occluded grain boundaries which may become embittled in the presence of oxygen, thereby nucleating cleavage fractures. High purity with respect to interstitial elements was found to inhibit twinning and evidence is presented for an orientation dependence of the resolved yield stress. Deformation occurred by slip rather than twinning at both temperatures of testing with elongations of as much as 9 pct at 20°K. THE fracture properties of iron single crystals have been observedl-3 to be a function of temperature, orientation, and purity. Allen, Hopkins, and McLennan1 demonstrated that at 78°K iron single crystals became increasingly brittle as the tensile axis approached the (001) pole of the stereographic unit triangle. Iron crystals with the tension axis near a (001) pole were completely brittle and orientations near the (011)-(111) boundary were very ductile, achieving a 100 pct reduction in area prior to fracture. Later work of Biggs and pratt2 and of Edmondson3 demonstrated that by reducing the carbon content of the single crystals the transition between brittle and ductile failure at 78°K could be shifted to orientations nearer the (001) pole. Ed-mondson went further and pointed out that any mechanism which tended to increase the yield strength of the iron (i.e., carbon addition, pre-strain) also increased the tendency for brittle behavior at 78°K. Thus by a reduction of carbon content Biggs and Pratt were able to obtain ductile behavior to within 20 deg of the (001) pole, and Ed-mondson was able to obtain ductile behavior to within 26 deg of the (001) pole. Edmondson&apos;s material had a total interstitial content (carbon, oxygen, and nitrogen) of approximately 60 ppm and, although Biggs and Pratt reported no analysis, indications were that their iron contained comparable impurities. Stein, Low, and seybolt4 purified iron single crystals to a total carbon, oxygen, and nitrogen content of approximately 20 ppm. They observed a lowering of the yield stress with this increased purity, and thus one might have expected an observation of increased ductility. Although they tested specimens of orientations which the previous workers had indicated should be ductile, the crystals failed at a 78°K in a brittle manner with little elongation. Stein noted,&apos; however, that about 90 pet of the failures could be traced in origin to occluded grains. Allen et al.1 and Edmondson3 do not report examination of their cleavage surfaces, but Biggs and pratt2 reported that microscopic examination of the cleavage surfaces of many of their specimens revealed the presence of small occluded grains. Honda and cohen6 and Keh7 have also observed the initiation of fracture at occluded grains in iron single crystals. Therefore, the additional complication of occluded grains must be considered in studying the properties of iron single crystals and the origin of fractures determined if the ductility exhibited by the crystals is to be considered meaningful. Various investigators8-12 have studied the effects of impurities on grain boundaries in high-purity polycrystalline iron. Rees and Hopkins10 showed that the addition of oxygen to low-carbon (0.002 pet) iron weakened the grain boundaries, causing a shift from transcrystalline to intercrystalline fracture and a progressive decrease on the brittle-fracture stress with increasing oxygen content. In addition, it has been shown by Low and Feustel11 that the addition of carbon to polycrystalline iron containing oxygen eliminated grain boundary brittleness. Thus, oxygen can embrittle grain boundaries in high-purity polycrystalline iron, but the addition of an appropriate amount of carbon can eliminate the oxygen-induced brittleness. The oxygen content (19 ppm) of the iron "single crystals" employed by Stein el al. was large enough to suspect impurity effects at the occluded grain boundaries. Allen et al.1 Biggs and pratt,2 and Edmondson3 may have masked any occluded grain problem in their specimens considering the relatively high carbon levels they employed. stein13 demonstrated that the addition of as little as 0.9 ppm C to previously purified (less than 5 x 10-3 ppm C) "single crystals" would increase the elongation from a few percent to more than 20 pet at 78°K and the fracture was not associated with grade boundary initiation.

Jan 1, 1965

By C. K. Gupta, P. K. Jena

Niobium (columbium) metal in the form of a button has been produced by calciothermic reduction of niobium pentoxide using sulfur as the heat booster. In these experiments with 50 g of niobium pentoxide per batch, the influence of percentage of calcium in excess of the stoichiometric, the percentage of sulfur by weight of the niobium oxide, and the outer-wall temperature of the bomb on the quality and yield of the metal has been studied. The maximum yield on this scale was 78 pct using 50 pct excess Ca and 20 pct of S and at a bomb-wall temperature of 600°C. In experiments conducted on 500 g of niobium pentoxide, reduction with 40 pct excess Ca and 20 pct of S, and at a bomb-wall temperature of 500°C, the.yield of the metal improved to 82 to 84 pct. Some of the reduced-metal samples have been electron-beam melted and the button melts thus obtained have been observed to be extremely ductile and capable of cold reduction to 98 pct without intermediate annealing. NIOBIUM, because of its high melting point (2468oC), its ductility, its resistance to corrosion especially in liquid metals, its high-temperature mechanical properties, and its relatively low capture cross section (1.1 barns) for thermal neutrons, has potentialities as a structural material in the field of nuclear engineering. Niobium and its alloys are also gaining importance in high-temperature technology as components in aircrafts, jet engines, and missiles, electronics, chemical engineering, and surgery. In 1904 Weiss and Aichel 1 produced niobium by reduction of its pentoxide by misch-metal. Since then a large number of investigations have been carried out for the extraction of niobium from its compounds. The various routes through which the metal niobium has been extracted from its compounds can broadely be classified into the following groups: a) reduction of its halides, oxides, and fluo-salts with metals like calcium, magnesium, sodium, and aluminum;2-10 b) reduction of its halides with hydrogen and oxides with carbon or carbides;11-18 c) electrolytic winning from its halides and fluo salts;19-25 and d) thermal decomposition and disproportion ion of its halides26-30 Among the processes in commercial use at present are sodium reduction or fused-salt electrolysis of potassium niobium fluoride, carbide or carbon reduction of the oxide, and hydrogen or metallothermic reduction of the chlorides. In 1907 Von Bolton2 prepared niobium by reducing niobium pentoxide with aluminum. Dennis and Adam-sona attempted reducing the oxide with magnesium powder in argon atmosphere and the resulting metal contained as much as 5 pct O. Mondolfo8 claimed a method for the reduction of the oxides with aluminum. In the case of both magnesium and aluminum reduction, it has been stated31 that by-product oxides such as MgO or A12O3 would involve a major separation problem. Further, in the case of alumino-thermic reduction, the solubility of aluminum in niobium and intermetallic formation have to be reckoned with. In 1922 Bridge3 produced niobium by calcium reduction of niobium pentoxide. Dennis and pdamson&apos; obtained the metal by a similar method with an oxygen content of 0.2 pct. In most of the cases of metallothermic reduction of niobium oxides mentioned above, the metal niobium is obtained in the form of powder. In an attempt to produce massive niobium metal, lock&apos; used iodine as the thermal booster in the bomb reduction of niobium pentoxide by calcium. Massive niobium metal was obtained with a maximum yield of 75 pct containing 0.1 pct 0. Joly32 carried out experiments on calcium reduction of niobium pentoxide on a 2-kg scale using sulfur as the heat booster in a sealed bomb filled with argon. In his experiments, the reaction was initiated by passing a current through niobium spiral wire embedded in the charge. In a typical run consisting of 2000 g of niobium pentoxide, 3100 g of calcium, and 800 g of sulfur (S/Nb2O5 = 3.3), he obtained massive metal in the form of a very uneven mass with a yield of -57 pct. With lower amounts of sulfur and calcium, powder niobium mixed with small metal globules was obtained and the yield was also poor. From these experiments he concluded that this method is not a suitable one for industrial development considering the quality and yield of metal obtainable and the possible hazards with higher ratios of sulfur to niobium pentoxide in the -~charere. In the present work, a detailed investigation on the calciothermic reduction of niobium pentoxide in a stainless-steel bomb in presence of sulfur as the heat booster was undertaken on a laboratory scale.

Jan 1, 1964

By William T. Folwell

The Lucky Friday mine east of Mullan, Idaho, is an outstanding example of a property in the Coeur dlAlene district where a small and insignificant-appearing silver-lead-zinc vein at the surface has changed at depth into a large vein of great importance. The Lucky Friday vein has little if any surface expression and above the 1200 level the ore shoots are small and discontinuous. Between the 1200 level and 2450 level, the lowest developed level, the main ore shoot has shown remarkable improvement on each succeeding lower level, and today the mine is one of the major lead-silver producers in the Coeur d&apos;Alene district. History: The Lucky Friday property is on the north side of the South Fork of the Coeur d&apos;Alene River in sections 25, 26 and 35, T. 48 N., R. 5 E., Hunter mining district, Shoshone County, Idaho. This is about one mile east of the town of Mullan, which serves the eastern portion of the Coeur d&apos;Alene district. The southern part of the property is crossed by a branch line of the Northern Pacific Ry. and by U. S. Highway 10. This highway is the principal road crossing the panhandle of Idaho and connects the district with Spokane, Wash., on the west and Missoula, Mont., on the east. The main portal and surface plant of the Lucky Friday mine is at an elevation of 3365 ft, only a short distance above the valley floor and a few hundred feet from U. S. Highway 10. so the mine is readily accessible for year-round operation. The property is comprised of six claims, known as the Lucky Friday group, owned outright by the Lucky Friday Silver-Lead Mines Co. There are four patented claims, Good Friday, Lucky Friday, Northern Light, and Lucky Friday Fraction No. 2 (Mineral Survey No. 3028), and two unpatented claims, Hunter and Creek. In addition, Lucky Friday owns an undivided one-half interest in the Hunter Creek property. which adjoins the Lucky Friday group on the north: a 90 pct interest in the mineral rights in the Jutila Ranch (160A), which adjoins the Lucky Friday group on the east; and a 60 pct interest in the Lucky Friday Extension claim group, which adjoins the Lucky Friday group on the west. The company also has a long-term mining lease on the Hunter Ranch, which adjoins the Lucky Friday group on the west. The claims of the Lucky Friday group were located between 1899 and 1906. The Lucky Friday Mines Co. was organized in 1906 and did considerable exploration work by surface trenching and shallow underground workings, only to see the property sold by the Shoshone county sheriff to satisfy labor claims totaling $2000 in 1912. Another firm, Lucky Friday Mining Co., bought the claims in 1914 and spent 12 years driving what is now known as the tunnel level crosscut. This tunnel intersected a vein previously exposed in a higher tunnel, but it was only a few inches wide. The vein was followed a short distance westerly but was so unpromising that the work was discontinued in favor of extending the main crosscut tunnel several hundred feet north. No ore was found and all work was discontinued. The property was held in such low esteem by the firm that it let taxes amounting to less than $15 a year go delinquent for nine years. Then the property lay idle for two more years until in 1938 John Sekulic, a Mullan service station operator, took a lease, with a $15,000 purchase option, on the advice of an old miner who had worked in the mine. Sekulic re-opened the tunnel level crosscut and explored the vein with an easterly drift for about 200 ft. The vein was too narrow to be of commercial value but was believed interesting enough to warrant further exploration at depth. Lacking funds to explore the vein at depth, Sekulic tried to get the district&apos;s larger operating companies to take over his lease and option. They were not interested because of the lean tunnel level showing and the fact that the property lay between the White Ledge fault on the north and Osburn fault on the south, an area which geologists always considered unworthy of exploration. Sekulic then organized the present company and assigned his lease and option to it for stock. This was in 1939. Enough stock was sold locally to finance sinking of a shaft 100 ft from the tunnel level east drift. The vein at this additional depth still was not commercial but showed some improvement. Treasury stock was offered at 5 to 10C a share

Jan 1, 1959

By Edna A. Dancy, Gerhard J. Derge

The specific conductance of FeOx,-CaO melts in contact with iron was found to decrease from 200 ohm-1 cm-1 for FeO, to 40 ohm-1 cm-1 for a melt containing 26.3 pct CaO at 1400°C. The temperature coefficient was positive at all compositions, but became smaller at high CaO contents. Current efficiencies for electrolysis increased from 2.5 pct in FeOx to 17.3 pct at the high CaO composition, indicating a change from predominantly electronic conduction to conduction with a substantial ionic contribution. It was shown that Ca++ ions as well as Fe++ ions carry the ionic current. A subsidiary investigation on the apparent effect of atmospheres of argon, helium, and nitrogen on the electrical conductivity showed that this could be correlated with surface temperature losses, which varied with the thermal conductivities of the gases and resulted in precipitation of metal by the reaction 3 Fe++ = 2 Fe+++ + Fe. The work described in this paper is offered as a contribution to the general fund of knowledge concerning metallurgical slags. Measurement of electrical conductivity and electrolysis are comparatively trouble -free methods for investigating molten materials, but, although these methods had been used for complex slags, it was not until the work of Bockris et al.1 that the approach of examining simple binary slag systems was employed, and CaO-SiO2, MnO-SiO2, and Al2O3-Si9 were studied. Two groups have performed work of particular relevance to the present investigation. Inouye, Tomlinson, and chipman2 studied the conductivity of wustite as a function of temperature and of the addition of 5 mol pct of a number of oxides, including CaO. They concluded that molten FeOx in equilibrium with iron is a semiconductor. Simnad, Derge, and ceorge3 demonstrated the ionic nature of liquid iron silicate slags and also concluded that, although the conductivity of FeOx in equilibrium with iron is predominantly electronic in nature, there is a small ionic contribution. The work reported here on FeOx,-CaO slags consists of three main parts, namely, the determination of the specific conductance over a wide composition range, an investigation into the nature of the conductivity through current-efficiency measurements over the same composition range, and an attempt to identify the current-carrying ions, as well as a subsidiary investigation on the apparent effect of the nature of the inert atmosphere on the conductivity. EXPERIMENTAL Materials. The slags, varying in composition from FeOx to 27 pct CaO, were prepared by heating reagent- grade Fe2O3 in an ingot iron crucible with a suitable amount of CaCO3 and, in some cases, powdered iron, in air. This prefused material was then used for the runs. At the end of each run the cell was removed from the furnace and quenched by immersing the bottom half in water. After crushing, the slags were analyzed for calcium and total iron by the usual wet methods. The oxygen content was obtained by difference. Specific Conductance: Apparatus and Method. Fig. shows the experimental setup, with the conductivity cell and leads of ingot iron. The standard four-probe method for measuring high conductivities was used. In this, the potential drop across the unknown resistance is compared with the potential drop across a known resistance connected in series, i .e., same current through both resistances. Thus there are both current and potential leads to the center electrode and to the crucible, which acts as th other electrode. Both ac and dc circuits were available for the measurements; they have been described in earlier work performed in this laboratory.4,5 The geometry of the cell was such that the center electrode was equidistant from the bottom and sides of the crucible. This ensured that the current path was the same irrespective of the magnitude of the conductivity of the material in the cell. Cell constant were measured with KC1 or NaCl solutions, which have considerably lower conductivities (0.0013 to 0.25 ohm-&apos; cm) than the slags, and this precaution in design made sure that the determined cell constants applied to the cells with contents of any conductivity. The cell-constant determinations were made with the ac measuring circuit to prevent polarization. The four-probe method eliminates lead resistance but not the resistance of those parts of the center

Jan 1, 1967

By Edmond S. Miksch

The morphology and growth rate of ice grown in supercooled water are markedly affected by convection of the water. A dendritic ice sheet with water flowing past the dendrite tip exhibits deflection of the dendrite spine toward the upstream direction, accelerated growth of secondary spines on the upstream side, and suppression 01" secondaries on the downstream side. Flow causes a thin disk to become corrugated, the corrugations being parallel to the flow. Flow causes an increase in the growth rate of the ice. IF a small seed of ice is placed in slightly supercooled water, it grows initially as a disk with the axis of the disk parallel to the c axis of the ice crystal.&apos; It appears that growth in the c direction is inhibited, while growth occurs with equal facility in all directions in the basal plane. It appears that growth rate as a function of interface temperature is very nearly equal for all directions similarly oriented relative to the c axis. Subsequent to the discoid growth, branching occurs and dendrites develop. The primary dendrite spines grow parallel to the six equivalent a axes of the crystal. Secondary, and in some cases, tertiary spines also grow in these directions. The highly anisotropic: dendritic growth indicates that there must be some finite difference of growth rate for different directions in the basal plane. These differences must be quite small, however, since if they were large, the discoid mode would not occur. Hence, it was expected that the dendrite growth direction could be deflected from the crystallographic direction by perturbation of the thermal field at the dendrite tip. Experiments were done in which perturbation of the thermal field was accomplished by causing the supercooled water to flow past the dendrite tip. The flow direction was perpendicular to the c axis of the crystal, and was perpendicular to the primary spine of the unperturbed crystal. Supercooled water was supplied by a 15 cm cubical copper box, which was refrigerated and insulated so it could cool water to temperatures down to —2oC, and maintain the temperature constant to O.l°C for the duration of a run. A lucite channel of rectangular cross-section, 12 by 24 mm, was mounted horizontally in the box, with one end open so water could flow into it, and the other end leading out through the wall of the box to a length of tubing leading: to an orifice plate 123 cm below. cnunMn s MIKSCH, MemberAiMe, formerly Research Associate, Research Associate, Fig. l(b)—Vertical section of apparatus A horizontal cross-section is shown in Fig. l(a), and a vertical section is shown in Fig. l(b). Means for observing the ice are shown in Fig. l(a). Collimated light passes through the ice sheet and forms an image on the ground glass screen. A lucite box containing dry air was employed to prevent condensation. Ice of the desired orientation was provided by the seed holder shown in Fig. l(b). This device was made of lucite, and had a reservoir in which ice could be frozen by placing it in a freezer. This reservoir com-unicated with the outside only through a narrow gap between two sheets of lucite. The seed holder (after ice had been washed off its exterior) was immersed in the tank of supercooled water, the narrow gap terminating in a slot in the top of the flow channel. Ice growing through a thin water layer in the gap between the two sheets of lucite was oriented so its c axis was perpendicular to the sheets. This orientation is an application of a growth phenomenon2 which causes ice growing along a smooth solid surface in supercooled water to orient itself so its c axis is normal to the surface. After the ice grew into the channel, further orientation was necessary, since the direction of the a axis

Jan 1, 1970

By John Riegle

To date. utility company underground storage of gas has generally been restricted to depleted dry gas fields. The Playa del Rey project is probably the first to successfully store gas in a partially depleted oil reservoir with the recovery of large volumes of pas at high rates as the main objective. Oil recovery has been a secondary consideration. Problems encountered unusual to those of storage in a dry gas zone were: (1) the removal and retardation of formation of emulsion. (2) the upstructure movement of fluid during withdrawal periods which formed fluid blocks, and (3) reservoir shrinkage resulting from encroachment of edgewater. The solution of these problems as outlined in the paper has resulted in increasing the withdrawal rate from the original design capacity of 4,000 Mcf per hour to the current 10.000 Mcf per hour. Additional increase is anticipated as the operations continue. Migration. reservoir performance. operational procedure and a historical record are included to make this a resume of the project from its war-time inception in 1942 to the first of 1952. INTRODUCTION The Playa del Rey underground gas storage project is probably the first project in which gas has been stored in a partially depleted oil reservoir, with the recovery of large volumes of gas at high rates as the main objective and the recovery of oil a secondary consideration. Problems unusual to those of storage in dry gas zones have made this a pioneer endeavor. The total storage capacity of approximately 1,500,000 Mcf of this reservoir is small in comparison with other underground gas storage projects. However. by study and experiment the deliverability into transmission lines. operating at pressures in excess of 150 lbs., has been nearly tripled in the past three years. to the current 10.000 Mcf per hour late, without the use of compression. It is anticipated this rate will gradually increase as additional fluid is removed from the formation. LOCATION AND HISTORY Playa del Key is located on Santa Monica Bay about two miles south of the beach commuity of Venice and 15 miles southwest of the renter of the City city Los Angeles. Fig. 1. The discovery well was completed at 6,194 ft in 1929. An upper zone at 3,905 ft was found on June 18. 1930. Townlot development was very rapid and by the end of 1930 there were 141 producing wells in the field. The Union Oil Co. completed a lower zone well south of the Townlot Field in May, 1931, which was believed to be an extension, until additional drilling of about 50 wells during 1934 and 1935 indicated this area to be a separate accumulation as shown on Fig. 2. The lower oil horizon, which is now the storage zone, had no original gas cap and is believed to be a continental detrital deposit of conglomerate that accumulated in valleys and depressions of a weathered schist high. which later subsided and was overlain by an impervious nodular shale. This type of formation has rapid variation of porosity. permeability and thickness due to lack of sorting action common to marine deposition. and the uneven surface of the original schist high. Production was limited on the upstructure sides by the pinching out of the conglomerate, and downstructure by edgewater. Unrestricted production, together with high permeabilities, led to large wastage of gas from this new area as facilities were not available for transport of gas to market. The decline was very rapid and by 1942 the portion of the new area south of Ballona Creek was nearly depleted. ACQUISITION OF PROPERTY The rapid increase in industrialization of Southern California during World war 11 forced upon the local gas com-

Jan 1, 1953