Search Documents

By J. E. Neal, C. T. Naber, O&apos

Silicon thin films were deposited by electron beam evaporation in an ultrahigh vacuum onto (0001) and (1102) sapphire substrates. Attempts were made to correlate the structural properties of the deposited silicon films with the following: 1) substrate orientation, 2) substrate surface condition, 3) substrate temperature, and 4) deposition rate. The substrate temperatures were varied between 500° and 1000°C and the deposition rates were varied between approximately 50 and 700A per min. The following sapphire surface treatments were investigated: 1) annealing in the ultrahigh vacuum at 1200° C; 2) heating in a hydrogen atmosphere at about 1350°C; and 3) etching with silicon by evaporating silicon onto sapphire substrates heated to 1200° or 1300°C. Twinned silicon films were occasionally formed at substrate temperatures between the 800° and 1000°C on unprocessed mechanically polished substrates; however, the reproducibility and crystallinity of these films were generally poor. Single-crystal and twinned silicon films were formed at substrate temperatures between 700° and 1000°C on substrates which were silicon-etched at 1300°C prior to deposition. Fiber texture films were formed at substrate temperatures between 500° and 700°C. The (111) lattice plane of the silicon single-crystal films was parallel to the (0001) sapphire plane and the (100) silicon plane was parallel to the (1102) sapphire plane. TECHNIQUES are well-established for growing single-crystal silicon thin films on sapphire by chemical methods.'-* Vacuum epitaxial techniques have a number of advantages over chemical epitaxial techniques in the fabrication of thin film microcircuits.5 One of the most significant is that vacuum techniques are compatible with well-established procedures for forming vacuum-deposited thin-film resistors, capacitors, and interconnections. Salatna, Tucker, and young6 recently reported the formation of relatively poor crystalline-quality silicon films on sapphire by electron beam evaporation in a vacuum of about 7 x 10-7 Torr. The purpose of the investigation described here is to determine the relationships between the structural properties of silicon thin films deposited on sapphire substrates by electron beam evaporation in an ultra-high vacuum and the following: 1) substrate orientation; 2) substrate surface condition; 3) substrate temperature; and 4) deposition rate. The substrate temperatures were varied between 500° and 1000° C and the deposition rates were varied between approximately 50 and 700A per min. Two orientations of sapphire were used: (0001) and (1102). The thick-nesses of the films were between 8000 and 16,000A. The morphology and crystallinity of the deposited films and substrate surfaces were investigated by optical microscopy, electron microscopy, and electron diffraction. APPARATUS AND PROCEDURE A cross section of the ultrahigh-vacuum thin-film evaporator is shown in Fig. 1. The bell jar is stainless steel and copper gaskets are utilized at all seals. High vacuum is attained by a 6001iter per sec ion pump and a titanium sublimation pump. Sorption pumps are used to rough the system to a pressure of about 10 µ prior to starting the ion pump. Vacuums in the 10- 10 Torr range were attained after baking the system at about 250°C for 8 hr. Vacuums in the 10-8 to 10-9 Torr range were maintained during silicon evaporation. The silicon charges, which were cut from p-type single-crystal boules which had resistivities between 2000 and 4500 ohm-cm, were placed in the water-cooled copper crucible of a 180 deg bent-beam 5-kw electron beam evaporator. During evaporation, a molten zone was formed in the top center of the silicon charge, and the portion of the silicon charge in contact with the water-cooled crucible remained solid. The substrate heater, which has been described

Jan 1, 1969

By John D. Verhoeven, Edward E. Hucke

An experimental technique has been developed for the measurement of the rate of electrotransport to a precision of 1 pct in the molten Bi-Sn system. Results are presented across the phase diagram from 30°C above the liquidus to 520°C. A phenomenological description is presented and the data on Bi-Sn are thereby converted to the effective charge, Analysis of the data indicates the true charge of the migrating tin species in bismuth to be +1.8 at 500°C. The data agree well with the recent work of Belashchmko. fieldintensity. The resistivity of the molten Bi-Sn system is also presented. WHEN an electric field is applied to a metal, a relatively large current is produced due to the ease with which electrons move within the metal. The electric field also produces a force on the ions which might cause them to migrate. Such a migration of metallic ions has been detected under certain conditions. This electromigration of the metallic ions will be referred to herein as electrotransport. The study of electrotransport in metallic systems has a rather long history dating back to the initial work of Gerardin1 in 1861. General reviews of electrotransport in liquid and solid metals have been published by Schwarz,2 Jost,3 Seith,4 and Heumann.5 In reviewing the literature it is apparent that the theoretical developments are not yet complete. The difficulty arises in describing the momentum transfer between the migrating ions and the electrons. In addition, there is a lack of good quantitative electrotransport data at high temperatures, especially in liquid metal systems. This work was undertaken to establish quantitative electrotransport data in a liquid metal system which might serve as a critical test of the theoretical developments. The Bi-Sn system was chosen for analysis, and the rate of electrotransport was determined as a function of temperature and composition. THEORETICAL CONSIDERATIONS If all of the atoms of a metal are considered to be positively charged due to the loss of electrons to the

Jan 1, 1963

By H. S. Martin

ALTHOUGH it was known some years ago at the- Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65¬mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. EARLIEST USE op MICROSCOPIC EXAMINATION OF TAILINGS As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for micro-scopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral particles or grains may be classified into separate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain no other included sulfides; 2. Grains in which all three of the copper sulfides are represented (the core may he of chalcopyrite, partially altered to bornite, these two minerals being entirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite.

Jan 1, 1929

By N. H. Harrison, J. K. Rodgers, S. Regier

This paper presents comparisons of data obtained from a laboratory reservoir study and from a calculated behavior prediction with the actual production history of a condensate reservoir. A small non-commercial discovery was depleted under closely controlled conditions and the well fluids were sampled at frequent intervals. Data on the reservoir and production variables were accumulated on a fixed schedule. A laboratory reservoir study war made using the initial well fluid samples as charging stock. The production procedures and operating conditions were held constant throughout the study wherever possible and in general paralleled the field work. The well fluid compositions and the cumulative recoveries ar a function of the reservoir pressure were also calculated using conventional flash vaporization procedures and equilibrium constants. Comparisons based on the composition of the well fluid show good agreement, the laboratory study agreeing within experimental accuracy with the field work and the calculated data comparing equally well. The gas-oil ratios are also in good agreement, but with somewhat greater deviations at the higher pressures. In the overall picture, it is believed that a model st,~tiy can predict within experimental accuracy the production history of a condensate reservoir. Better equilibrium constants for the heavier hydrocarbons are needed in order to attain improved composition accuracy by calculation. INTRODUCTION In Aug., 1955, a gas condensate well was completed in San Juan County, Utah, that was initially thought capable of good commercial production. These conclusions were derived principally from core data and electric logs, which indicated good permeability, porosity and gas content. However, after the usual series of potential tests it was found that the reservoir pressure had declined some 22 per cent, and it was obvious that the zone tapped was but a small pocket or trap. It became apparent that, with a controlled depletion of a small reservoir, a unique opportunity was available to compare laboratory and calculated studies with an actual field depletion and to further the present knowledge of condensate reservoirs. FIELD WORK The Coalbed Canyon Well No. 1 was conventionally completed in the Paradox limestone formation to a total depth of 5,912 ft. The producing zone from 5,762 to 5,806 ft was perforated with four jet shots per ft. The wellhead and field equipment were also conventional, the major items consisting of a two-pass indirect fired line heater, a high- and a low-pressure separator with the necessary controls and accessories, gas meters, back-pressure regulators, flare stacks and condensate stock tanks. The initial testing of this well con-sisted of a series of flow potential and pressure build-up tests during which some 30 MMcf of gas was produced. The reservoir pressure declined from an estimated 2,300 to 1,782 psig during this period, from which it was concluded that the reservoir was very small. In order to approach steady-state conditions in the reservoir and so provide optimum conditions for making comparisons, the field depletion was programmed to approach, if possible, constant production conditions. Bi-hourly readings were taken of the tubing pressure, the pressure and temperature of the separators, oil and gas rates, and other pertinent operating data. The gas rate, as indicated by the orifice meter, was held constant by the adjustment of the choke in the line heater. The temperature of the first stage separator was held constant by adjustment of the line heater jacket temperature. Practical considerations of production made the maintenance oi a constant gas rate impossible. The test started with a gas rate of 4 MMcf/D and a separator pressure of 250 psig. This rate was maintained until the choke was fully opened. The gas rate then declined with the falling tubing pressure and production was continued until the rate was about 2

By Tuncel M. Yegulalp, Malcolm T. Wane

In general, many problems relating to the exploitation of mineral deposits are probabilistic in nature. This derives from the fact that the geologic universe is inherently random. Probability theory and statistics have been found useful for forecasting the behavior of natural events that occur in the geologic universe. The objective of this paper is to illustrate the application of the theory of extremes to this fore-casting problem. For example, it is customary for design purposes to determine the rupture strength of geologic materials. The theory of extremes is exceedingly useful in describing that portion of the frequency distribution of rupture strength which contains the least strengths. Parameters describing the distribution of the least strengths are more important to the designer of mining excavations than parameters describing the total distribution. The basic principles of the theory of extremes will be detailed and illustrated. Any person required to work in the laboratory of nature is aware that uncertainty is a salient feature of all mining enterprises. A mining engineer required to plan the most efficient, practicable, profitable, and safe mine finds himself face to face with numerous ill-understood and often unquantifiable states of nature. Basic information necessary for adequate planning is often lacking or derived from incomplete tests on samples or experience of doubtful validity. The planning procedure usually takes the form of determining a feasible layout with the intent of determining an optimal layout when and if the necessary details and information become available. The crux of the entire procedure is the choosing of numbers to put into the operational and structural models which encompass the plan. Many times these numbers must be assigned qualitatively from past experiences and are called the "most probable ones." At other times, load records, performance records and material tests provide a basis for extrapolation. In any event, the numbers are chosen from a distribution or set of all numbers. Since each number in the distribution represents a possible state, the choice of any particular value is based upon a decision rule. To illustrate, consider the design of an underground structure or the design of a rock slope. The initial step is the formulation of the various possible structural actions which result from the geometry of the layout. For a given structural model various intensities of behavior are possible depending upon the load, deformation, and material characteristic spec-trums, respectively. Of particular interest to mining people is the failure behavior or condition, i.e., when there is a complete collapse of structural resistance by either structural instability or fracture. A necessary feature of the analysis is the "rupture strength" of the material. Information on the rupture strength is derived from testing either in situ or in the laboratory and the usual outcome is a variation in the test results. The methodology used to overcome this variation is to construct a frequency distribution of rupture strengths, and then determine a measure of central tendency and variability. The main idea involved is that the central tendency number will be used in the failure calculations and the measure of dispersion will be used to estimate the probability of failure. In particular if the distribution of rupture strength is normal, the mean rupture strength is the central tendency number and the standard deviation of the rupture strength is the measure of variability. Suppose the mean value of rupture strength is 1000 psi and the standard deviation is 200 psi. Insertion of 1000 psi into the failure calculation produces results that are unsafe, hence a common decision rule is to reduce the mean value by a "factor of ignorance" so that the failure calculation will produce a "safe result." If two is chosen as a factor of ignorance, this means the value inserted in the calculation is 500 psi or 2.5 times the standard deviation. The next step is to determine the percentage chance that failure will occur from a design created on this basis. Tables on the normal distribution function show that this percentage chance is 0.621% or approximately 7 times out of 1000. In practice, however, the situation is more complicated than represented by the foregoing illustration. The laboratory or field testing program usually constitutes a pathetically small sample of the geologic universe of interest and not enough testing is carried out to determine the exact form of the distribution of the test results. The normal, Cauchy and Student's T distributions are strikingly similar, and it becomes a matter of mathematical convenience to assume the normal law for phenomena which follow other laws.

Jan 1, 1969

By P. D. Merica

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903-1911 by A. Wilm1,2 and have been described by him and by others. 3 4 5 6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from temperatures below its melting point followed by aging at ordinary temperatures, which consists merely f allowing the material to stand at these temperatures. The hardness is not produced by the quenching alone but increases during the period of aging, which may be from one to three days. Cohn3, 5 gives data showing the increase of hardness of duralumin during aging, after quenching in water from about 450° C. Upon annealing, the alloy so hardened by aging is softened exactly as is hardened steel. The composition of this alloy usually varies within the following limits: Copper, 3 to 4.5 per cent.; magnesium, 0.4 to 1.0 per cent.; manganese, 0 to 0.7 per cent.; aluminum, balance; iron (as impurities), 0.4 to 1 per cent.; silicon, 0.3 to 0.6 per cent. Its density is about 2.85. It is used only in the forged or rolled condition. This alloy has been produced for some years commercially and is in demand for the fabrication of parts for which both lightness and strength are required, such as for aircraft. Its tensile strength will average 50,000 to 60,000 lb. per. sq. in. (3515 to 4218, kg. per sq. cm.) after appropriate heat treatment, such as that described by Wilm.

Jan 6, 1919

By Ogden B. Malin

In conducting the manufacture of extruded brass rods and brass forgings it has been noticed that there is considerable variation in the physical properties, particularly the machinability of different rods and forgings, even though the composition, working temperatures and method of manufacture remain the same. It is the purpose of this paper to attempt to establish the cause and extent of this variation, and also to determine whether variations in composition within certain defined limits influence hardness and machinability to any marked degree. The writer believes that this variation probably is due to the variation in grain size of the metal, therefore the microstructures of several compositions under various conditions of working were examined in an effort to establish this as a fact. Survey of Previous Work in Studying Extrusion Defects Very little has been published concerning defects in extruded and forged brass. In 1921, R. Genders1 $ delivered a paper before the British Institute of Metals, relative to a defect inherent in the extrusion process. This defect, commonly found in extruded brass rod, shows up in the form of a circle in a transverse section consisting of oxides and impurities, and is generally present in the last 25 to 30 per cent of the rod. Genders concluded that the defect is caused by the turning inward of the skin of the billet at the edge of the plunger because the inside of the billet is more plastic than the outside, which is in contact with the cooler container; the outside skin will lag behind to form the rear end of the rod. Genders suggested a movable die as a remedy, and while this met with fair success, it is not used in present practice. About the same time as Genders' experiments, Tucker2 and Rosen-hain3 conducted experiments using colored plasticene in the form of a billet, and found much the same defect as Genders. Dr. Rosenhain State College, Pa.

Jan 1, 1932

By N. Mungan

A study was made of the effects of wettability and interfacial tension on the immiscible displacement of a Iiquid by another Iiquid from porous media. The influence of viscosity ratio was also investigated. Porous media used were polytetrafluoroethylene (TFE) cores prepared by compressing TFE powder under different pressures. lt is shown that displacement of a wetting by a nonwetting Iiquid is always less efficient than the displacement of a nonwetting by a wetting fluid, all other things being equal. In the former case, the recovery efficiency can be increased substantially by either reducing the interfacial tension or increasing the viscosity of the displacing fluid. A qualitative discussion is given on the implications of this work to the recovery of crude oil by water flooding. INTRODUCTION The high cost of oil exploration and new recovery schemes makes it imperative that waterflooding be conducted under conditions favoring most efficient oil recovery. To improve oil recovery by waterflooding, it is essential that the role played by interfacial forces in the entrapment of residual oil be studied and understood. Interfacial phenomena in natural rock, connate water and crude oil systems are very complicated because of the complexity of the natural liquids found in petroleum reservoirs, because of our inability to adequately describe the geometrical structure of the porous media and because of a lack of understanding of physical and chemical interactions between the liquids and surface of the pores. The problem becomes further complicated when one tries to elucidate the role of interfacial phenomena in fluid flow. Numerous studies of the displacement of oil by water under different interfacial tension or wet-tability conditions have been made.lm3 These studies have been performed in silica, alundum or sandstone systems using water and paraffin oil and also some surface active material to control the interfacial tension s and the contact angle 0. Unfortunately, the high energies of various interfaces involved favor adsorption and orientation of the surface active material at the interfaces. Also the surface active material concentration at the interfaces exceeds that in the bulk of the liquid phases. Such surface excess may cause the surfactant distribution, the contact angle and the interfacial tension to differ from their measured static equilibrium values and makes interpretation of the displacement experiments difficult. Furthermore, as changes in s also lead to changes in cos 0, the role played individually by one of these parameters in the displacement becomes obscured by the effect of the other. To circumvent these difficulties, a low surface energy solid and true solutions or pure liquids should be used. Use of a low surface energy solid minimizes adsorption and orientation effects at the solid-liquid interfaces. By controlling s and cos 0 through use of selected pairs of pure liquids or true solutions rather than by surfactants, the adsorption effects at liquid-liquid interfaces are eliminated. In the present study TFE cores were used as the porous media. Liquids used were water, sucrose solutions, paraffin oils and benzyl, n-butyl and isobutyl alcohols. The interfacial tension was varied from 40 to 1.1 dynes/cm by suitably choosing the liquid pair. A surface active material was added to the water-oil system only in the case where interfacial tension of 0.5 dyne/ cm was desired. No precise changes of cos 0 were attempted. However, either the displaced or the displacing liquid could be made the one which preferentially wets the TFE surface. Using sucrose solutions and blends of paraffin oils proved to be a convenient way of changing the viscosity ratio between the displaced and displacing liquids. The present investigation examines the effect of interfacial tension, wettability and viscosity ratio on the immiscible liquid-liquid displacement from porous media. Observed data permit a

Jan 1, 1967

By Anson Hayes, John Chipman

The quality of sheet and strip products made of rimming steel is closely related to the structure and chemistry of the ingots. The variation in composition throughout the ingot, as affected by segregation, is of great importance, as are also the form and distribution of the voids that result from the gases evolved. It is because of this importance that the considerable literature in this field has accumulated. No attempt is made in the present paper to compile a bibliography of the excellent work that has already been done, as this has been adequately covered in the many excellent reports on the heterogeneity of steel ingots prepared by a joint committee and published by the Iron and Steel Institute.' From time to time, in any field of investigation new tools and new technique are developed, which make further progress possible. In the field with which this paper is concerned, this is true. The development of the vacuum-fusion method as a means of following oxygen segregation, and a technique for obtaining the volume and composition of the gases evolved during solidification, have opened the way to obtaining data by means of which some considerable progress has been realized in developing more of the detailed mechanisms of solidification and segregation in rimming-steel ingots. General Theory of Segregation The basic cause of segregation lies in the fact that the impurities are less soluble in solid than in liquid iron. The solid that forms from the impure liquid is more nearly pure than the liquid itself. If solidification proceeds slowly enough, or if the liquid and solid phases are maintained in contact with one another for a sufficient time, a condition of equilibrium is set up, which may be represented by a phase diagram. Portions of the

Jan 1, 1939

By F. E. Jaumot, R. L. Smith

Self-diffusion in zinc at temperatures below 200°C has been studied using both single crystal and polycrystal samples. Anomalous results were obtained for single crystal samples, the data indicating that in some cases grain boundary diffusion predominated. These anomalous results are presumed to be due to low angle lineage boundaries in the single crystals. When volume diffusion occurred in either single or polycrystal samples, the values for the diffusion coefficient were as much as several orders of magnitude larger than would be expected from high temperature data. ONSIDERABLE work has been done on self-^-*diffusion at temperatures in the neighborhood of two thirds of the melting temperature (in OK) and higher, but very little has been done at lower temperatures. This is particularly true of self-diffusion in single crystals. This paper reports work on self-diffusion in zinc at temperatures below 200 °C where both polycrystalline and single crystal samples have been used. The measurements were made using both the sectioning and absorption techniques. The experiments on diffusion at low temperatures were initiated primarily for three reasons: to obtain data from single crystal diffusion covering a wide range of temperatures, to obtain values of the activation energy for grain boundary diffusion, and to obtain, if possible, a lower limit to the temperatures at which the absorption technique may be used. It is possible to determine whether volume or grain boundary diffusion predominates at low temperatures by analyzing the manner in which the concentration of the diffusing atoms varies with the depth of penetration. The analysis is possible only for the sectioning technique. For volume diffusion and for the boundary conditions of the present experiment, the curve of the logarithm of the concentration, C, vs the square of the penetration depth, x, is a straight line with the slope proportional to — 1/D. If grain boundary diffusion predominates, Fisher' has shown that a curve of In C vs the first power of the penetration depth should be a straight line. This linear dependence of concentration on depth has been observed experimentally by several investigators. (See, for example, refs. 3 and 4.) Following Fisher's analysis, the grain boundary diffusion coefficient can be written as where 8 is the grain boundary width, D, is the volume diffusion coefficient at the temperature involved, t is the time of diffusion, C is the concentration of diffusing material, and x is the depth of penetration. A more general analysis employing the same model as Fisher's but with fewer assumptions has been given by Whipple.' In contrast to Fisher's analysis the more general analysis of Whipple does not always yield a straight line relation between In C and x. Recently Turnbull and Hoffman have discussed both analyses and have applied the Fisher-Whipple model to a more refined dislocation model of the grain boundary. They have also discussed the possibility of a large effect of grain boundary direction on diffusion. In the case of the absorption technique, for which results are also given, one simply gets a value for the diffusion coefficient with no indication of the predominating mechanism. Experimental Techniques Single crystals of 99.99+ pct Zn were grown using a modified Bridgman method. Polycrystal samples were prepared in three grain sizes (small, about 4 mm2; medium, about 9 mm'; and large, about 25 mmz) by quenching, air cooling, and furnace cooling. The grains of the polycrystalline samples tended to be columnar, with some preferred texture such that the c-axis was inclined at about 20" to 25" from the normal to the diffusion face, particularly in the medium and large grain size samples. The samples were cut from the rod, polished, and heavily etched, and faces cut accurately parallel using a jeweler's lathe. They were again etched to remove the lathe smear and annealed for 3 hr at 250" to 300°C. After annealing, they were etched, examined, and the orientation determined by Laue back reflection photographs. They were then electroplated with Zn. The plated surfaces were examined for uniformity; nonuniform coatings were removed by etching and the samples replated without additional preparation. For the diffusion anneals, the samples were placed in pairs, with active faces together, in evacuated Pyrex tubes. Constant temperature baths were used, and the variation in temperature did not exceed ±l°C, Diffusion runs were made at l00°,

Jan 1, 1957

By D. J. Rose, W. M. Armstrong, A. C. D. Chaklader

The wetiability of single crystals of MgO by specimens of vacuum-cast iron was studied using the sessile drop technique in vacuo at 1550ºC. Formation of FeO at the liquid-vapor interface caused the contact angle (6) to decrease from 117 to 65 deg during the first minute. After cooling, all specimens possessed a peculiar annular interfacial deposit of Fe,O,. Within the annulus the interface showed no sign of chemical attack. Chemical reaction occurred where the iron was alloyed with Ti, V, Cr, Nb(Cb), Ta, cmd Zr. Vnriation of 6 with alloy concentration was studied. Although vanadium md chromium improved the wettability of MgO by iron, the effect of Zr, Ti, Nb, and Ta was indeterminable because the 8 derived from sessile drop considerations was that of the metal against a restrictive peripheral volume of liquid oxide wetting the substrate. INTEREST in the nature of metal-ceramic interactions has been stimulated by progressive development of metal-ceramic combinations. One of the more valuable methods used for bond investigation is the sessile drop technique. Recent attempts to improve wettability through solute additions to the drop have revealed that the solute may a) react with the oxide creating new compounds at the solid-liquid interface, b) adsorb at the interface in a monolayer formation, or c) distribute throughout the drop uniformly causing no wettability variation. This work, part m in a series1,2 of investigations of interface reactions between metals and ceramics, embraces a study of the Fe-MgO system. MgO possesses a large negative free energy of formation (-173 kcal per g mole 0, at 1550ºC) compared to FeO at this temperature (-73 kcal per g mole 02). Hence the electronegativity difference between the drop and substrate allows selection from an extensive group of metal solutes with intermediate electronegativity differences that would, in the absence of chemical reactions, be expected to adsorb pre- ferentially at the solid-liquid interface. However, the high oxygen pressure of MgO in vacuo creates an oxidation environment which influences the solute behavior. Recent studies of the Fe-MgO systemJ74 have been restricted by chemical reactions that obscured observations. In view of the current interest in liquid-phase sintering of metal-ceramic combinations under partial oxidizing conditions,5 a more comprehensive study of the Fe-MgO system seemed beneficial. EXPERIMENTAL PROCEDURE 1) Specimen Preparation. Optical-grade MgO single crystals and Ferrovac vacuum-cast iron were used in all experiments. A spectrographic analysis of the iron indicated 0.008 C, 0.05 V, 0.005 Mo, 0.01 Ti, 0.002 S, 0.01 Cr, 0.001 Mg, 0.01 Si, 0.003 A1 (wt pct). The MgO crystals were cleaved along (100) planes into plates approximately 20 by 20 by 1 mm. Following annealing in vactto at 1100°C for 3 hr, surface irregularities were removed by a chemical etch in phosphoric acid at 100°C. The iron rod was machined into small cylinders approximately 0.250 in. in diam and length and these were carefully cleaned in organic and acidic solutions to remove surface impurities. All specimens were weighed to the nearest 0.1 mg. 2) Apparatus. The apparatus described in detail by previous authors1,2 was modified for this work. A Polaroid Land Camera was incorporated into the optical system so that drop measurements at ten-second intervals after melting were possible with ultra-high-speed self-develop ing film. 3) Procedure. The iron cylinders were placed upright on the MgO plates and positioned in the molybdenum susceptor. After furnace assembly the system was pumped down to a vacuum of 1 µ and flushed with H2 at 800°C. The system was again evacuated to 5 x 10-5 mm of mercury and the temperature raised to 1550°C within 2 min. The molten drops were photographed at appropriate time intervals. TWO min after melting the iron vapor pressure caused gas discharge, or corona, within the tube. The specimens were then slowly cooled to room temperature, sectioned and examined metallographi-cally. X-ray identification of interfacial reaction products was attempted by the powder diffraction technique. Alloying elements (Ti, V, Cr, Zr, Ta, Nb) were added to the iron in various concentrations up

Jan 1, 1963

By M. Kaufman, A. E. Palty

The phase structure and aging characteristics of two nickel-base alloys, Inconel 718 and 702, were investigated. Wrought and cast Inconel 718 showed ArisCb as the major hardening phase, as well as ture was positively identified. Inconel 702 had Ni3Al as the major hardening phase, as well as Cr7C3-of the phase amounts with temperature was determined. 1 HE value of phase structure and aging rate information in the utilization of alloys has been well established. As part of a continuing program, the results obtained on two nickel-base alloys, hconel 718 and Inconel 702, are presented here. Inconel 718 is a relatively new alloy considered for application in both sheet and cast form. Its novelty lies in the use of high columbium tantalum levels in a Ni-Cr-Fe base. No previous work on this type of alloy has been reported in the literature. Inconel 702 is being used now as an oxidation-resistant sheet alloy. Occasional fabrication problems spurred work on its basic structural behavior. The composition of 702 is essentially nichrome plus aluminum and titanium for strengthening and added oxidation resistance. This puts it in the basic class of other nickel-base alloys which have already been studied. The two alloys will be treated separately. INCONEL 718 Phase Study Methods. The phases present after the various conditions investigated were determined by X-ray diffraction analysis of two different elec-trolytically extracted residues and microscopic examination. The extraction methods, using 10 pct HC1 in alcohol and 10 pct H3PO, in water and the X-ray technique have been described previously.' The effect of temperature on the phase behavior was studied on sheet material using the following heat treatments: 2250°F, 2 hr, ice brine quench 1300 100 hr, water quench 2250°F, 2 hr, ice brine quench 1400°, 100 hr, water quench 2250°F, 2 hr, ice brine quench 1500°F, 100 hr, water quench 2250o 2 hr, ice brine quench 1700°F, 48 hr, water quench 2250°F, 2 hr, ice brine quench 1850°, 24 hr, water quench 2250°, 2 hr, ice brine quench 2000°F, 6 hr, water quench The high solution temperature was an attempt to dissolve as many phases as possible without causing melting. Aging exposures were made longer than normal heat treating times in order to approach equilibrium conditions more closely. Cast material was examined only in the as-cast condition and with the normal heat treatment (1700°F, 1 hr, air cool 1325oF, 16 hr,air cool). Materials. The full phase study was performed on sheet specimens approximately 1/2 in. by 2 in. by 1/16 in. The cast pieces were cut from the gating system of a vacuum-cast test piece. An all weld-metal specimen was made by running many weld beads on the sheet using filler made from the sheared edges of the sheet. All external contamination was removed by belt-sanding followed by an electro-polishing treatment. The typical composition of wrought Inco 718 is as follows: The alloy is air-melted. Cast hco 718 may have higher molybdenum. Due to the expectation of finding a Ni-Cb phase (Ni, Cb) for which no X-ray diffraction pattern was available in the ASTM Index, a special 5 Ib heat to the stoichiometric composition of this intermetallic

Jan 1, 1962

By George S. Rice

Those who for the first time see, at a mine, a great hole caused by subsidence; or, going underground, see an extensive fall of roof or hanging wall are apt to regard such an occurrence as an accident and not a normal condition of exhaustive mining. Moreover, the public is inclined to believe that a cave or subsidence of the surface is the result of carelcssness in mining or the rapacity of the mine operators in "robbing pillars," a tern too loosely used in descriptions of coal mining. This belief is fostered by the common-law requirement that an owner of the surface or of surface improvements is entitled to full support of the surface. Court decisions have upheld this law even when that owner has sold or leased the underlying mineral, unless a clause in the sale or lease contract exempts the mining company from paying the owner of the surface for damages that may result from mining. Another reason for this belief is the earlier practice (which is still extensively followed in this country) of leaving all coal pillars unmined, except as they have been thinned by so-called robbing; by not extracting the pillars, the surface may be supported by them for years, perhaps for generations. Inasmuch as the practice of leaving permanently in the mines from one-third to one-half of the mineral is wrong, with respect to conservation of a national resource, it behooves the mining engineers to assemble data and disseminate information on the subject, pointing out that subsidence must follow complete extraction, unless expensive methods of back-filling are employed, such as are used in Germany and France. These methods inevitably increase the cost of mining and the price of the mineral produced. It is popular to speak of "waste in mining" without a realization that much so-called wasting is unavoidable unless subsidence is accepted and provision made therefor where the surface is valuable, or else the only present known alternative of hydraulically placing sand or crushed stone filling in the excavations, at an increased cost of the mineral product to the consumer.

Jan 1, 1923

By D. Turnbull, J. E. May

THE (110) [001] texture in silicon iron is of considerable interest both from the technological and scientific points of view. Its occurrence was reported more than 20 years ago.1-4 The texture develops by means of secondary re crystallizatjon5 and can be very strong, that is, greater than 90 pct alignment even thouh the primary re crystallization texture is weak or complex. This behavior is in contradistinction to the face-centered metals which develop their strong secondary recrystalliza-tion texture from a strong primary recrystalliza-tion texture.', The microstructural changes accompanying the (110) [001] texture formation in silicon iron are as follows: When properly prepared cold-rolled sheet (i.e., 0.015 in. thick) is annealed at about 800°C, primary recrystallization occurs and a fairly stable fine-grained primary recrystallized matrix of about 0.02-mm-diam grain size is produced. The material at this stage does not have the strong (110) [110] texture. As the temperature is raised to about 900°C, relatively large grains appear in the finegrained matrix and they grow at the expense of the smaller grains to many times the sheet thickness. In time the complete sample is consumed by these large grains. This process of the growth of relatively few grains (about one in 105 primary grains) at the expense of many grains is called secondary recrystallization. Since all the secondary grains are of essentially (110) [001.] orientation, the strong texture is developed by this secondary recrystallization process. Theories of the (110) [001] texture in polycrystal-line silicon iron have been proposed by Decker and Harker and by Dunn.Decker and Harker have shown that grains initially in the (110) [001] orientation will upon annealing after cold-rolling, re-crystallize back to the initial orientation. To account for the sharp texture in silicon iron they propose that (110) [001] grains become more highly strained than grains in other orientations and therefore recrystallize first. They are then the lowest energy grains and can consume their higher energy neighbors. Grains in orientations other than (110)

Jan 1, 1959

By G. M. Yocom

Blowing acid Bessemer converters with oxygen-steam produces steel of below 0.002 pct N2 content. This method of blowing, combined with a dephosphorizing treatment in the steel ladle, results in low-carbon steels of low nitrogen and low phosphorous (under 0.035 pet) contents, which has physical properties equivalent to open-hearth steels of similar analysis. Using a 50-50 mixture of oxygen and steam, the refinitzg rate is increased 25 pct over blowing with natural air, and scrap charge increased from 3 to 10 pet. Bottom life is normal with proper tuyere area and arrangements, fumes are decreased, yields increased, and hydrogen content is normal. THE acid Bessemer plant at the South Works of Wheeling Steel Corp., consists of two 15-ton bottom blown converters with a monthly capacity of 57,000 N.T. The product of the shop is skelp billets for continuous welded pipe and slabs for ordinary drawing and forming quality sheets. Approximately 50 pct of ingot production is regular Bessemer steel of natural Phos content and the remainder is a dephosphorized grade of steel made by a special treatment of the blown metal as it is poured into the steel ladle. The low Phos grade of steel has certain advantages over the higher Phos grade but since both grades were produced by blowing natural air, the N2 content was in the range of 0.015 pct which limited its application. In 1954 it was decided to explore the possibilities of blowing with a steam-oxygen mixture for the production of steel of both low N2 and low Phos contents. The necessary equipment was installed to operate one converter in this manner and early in 1955 an experimental run of 160 heats was made by blowing with a steam-oxygen blast and excluding natural air entirely. During this period the proper operating techniques were established, such as blast pressures, steam-oxygen mixtures, valves and instrumental control equipment, tuyere arrangement in the bottoms, blowing times and production rates, and a thorough study made of the final steel quality. Also during this experimental period the dephosphorizing practice was improved by the use of a tap hole below the lip of the vessel. This provided a clean separation of the acid converter slag and blown metal which made the dephosphorizing treatment more effective. The results of this experimental run dictated further development of this practice and a second run of 720 heats was made in 1957. The quality features and conversion cost results were in line with expectations and accordingly a 400-ton per day oxygen plant is now being installed. The plant is scheduled for completion in September of this year. This will provide sufficient oxygen to operate both vessels on steam-oxygen blast and delete natural air blowing entirely. The steel will then be below 0.002 pct N2 bar content and the dephosphorized grades will be between 0.015 and 0.040 pct Phos. STEAM-OXYGEN BLOWING The steam for the process is fed to the plant at 220 psig pressure through a 6-in. line. The high-purity oxygen is compressed to 200 psig and conducted through an 8-in. line. The oxygen from the main line is valved down to 100 psig and passed through a steam heated heat exchanger. The heat exchanger is regulated to supply oxygen at 300°F to the steam-oxygen mixing station. It is essential that the incoming oxygen be held at this temperature to avoid condensation of the steam with resulting excessive erosion of the clay tuyeres in the vessel bottom. Oxygen is admitted to the mixing chamber by a 6-in. hydraulically operated valve driven by the ratio control regulator on impulse from the flow of steam. Steam is admitted to the steam-oxygen mixture station through a 2 1/2-in. hydraulically driven valve. The ratio control regulator acts to increase or decrease oxygen input as the steam flow increases or decreases with changing positions of the Blower's control lever. The important point to note here is that steam flow always precedes the oxygen flow as a safety measure. The control valves have sufficient capacity to afford protection should blow pipe trouble develop. A 50-50 mixture for these 15-ton heats demands an oxygen flow of 3800 standard cu ft per min along with 317 lb of steam. The Blower's stations is provided with an indicating blast pressure gage, and indicating steam and oxygen flow meters. Signal and warning lights indicate the valve positions and line pressures. A control room at the real of the Blower's pulpit room houses the ratio control and pressure regulators, as well as the various meter bodies. The hand actuated wheels used to change the conditions are mounted on a panel on the front of the meter control house. The recording steam and oxygen meters used for totalizing and accounting purposes are also mounted on this panel.

Jan 1, 1962

By R. A. Burmeister, G. P. Pighini, P. E. Greene

An open tube vapor phase epitaxial growth system has been used for large area (multiple substrate) growth of GaAs1-xPx on GaAs substrates. The GaCl-GaCl transport reaction is used with either a GaAs or Ga (nonsaturated) source. Selenium and tellurium have been used for donor impurities, and zinc as an acceptor. The useable substrate area in this system is approximately 20 sq cm. The uniformity of thick-ness of the epitaxial layers are typically better than ±5 pct across a given wafer. Electrical and optical measurerments indicute comparable uniformity in electrical and luminescent properties within a wufer. The application of this system to the large scale pro-duction of GaAs1-x Px for display devices, both discrete and arrays, is discussed. Typical electrical and luminescent properties of light emitting diodes fabricated front material produced by this technique are presented. THE most promising materials currently being utilized for visible injection electroluminescence are GaAs1-xPx, Ga1-xAlxAs, and Gap. All have reasonably efficient emissions in the red portion of the visible spectrum at room temperature; Gap also has an efficient green emission.' At present, GaAs1-xPx has a technological advantage over Ga1-xAlxAs and Gap for display applications, since relatively large (several sq cm) areas of GaAs1-xPx suitable for use in electroluminescent devices may be readily grown by vapor phase growth techniques. In contrast, the preparation of Gap and Ga1-xAlxAs for electroluminescent device applications generally employs solution growth techniques which are at present not well suited for the growth of large areas of uniform thickness and doping level. The capability of uniform growth over large substrate areas and the use of multiple substrates is necessary for the practical utilization of electroluminescent devices. This is particularly important when quantity production or monolithic devices are required. Furthermore, in many display applications arrays of light emitting devices are used, the individual elements of which are of a size resolvable by the unaided eye. Thus the overall dimensions of display are substantially larger than those of most semiconductor devices. It is also necessary to achieve a high degree of control over the growth parameters to attain the required degree of reproducibility of materials properties for electroluminescent devices. In the case of GaAs1-xPx it is necessary to accurately and precisely control the phosphorus content of the alloy, both on a macroscopic and microscopic scale, in addition to the parameters generally associated with epitaxial growth such as thickness and doping level. This value is critical, as it has a major effect on the performance of electroluminescent devices. This paper describes the epitaxial growth of GaAsl-xPx suitable for electroluminescent display devices using a system developed specifically for this purpose, and which contains several novel features. The results of studies of selected physical properties of the epitaxial layers are also discussed. Finally, a brief summary is given of the characteristics of display devices fabricated from GaAsl-xPx grown in this system. EXPERIMENTAL A) Reactants. A number of techniques suitable for the vapor phase epitaxial growth of GaAs1-xPx have been reported in the literature.'-' The method selected for this investigation is that in which the Ga is transported by the GaC1-GaCI3 reaction in an open tube process. The results reported here were obtained using either the combination of GaAs, AsC13, and pH3, or Ga, AsH3, pH3, and HC1 as the initial re-actants.* The ASH3 and pH3 were obtained as dilute *Several different sources of supply were used for these reactants, y~elding comparable results._____________________________________________________ mixtures in HZ; the HC1 was obtained from the reduction of AsC13 by Hz at elevated temperatures. Both selenium and tellurium were employed as donor impurities, and zinc as an acceptor impurity. Selenium was introduced in the form of H2Se, tellurium in the form of tellurium-doped GaAs, and zinc in the form of diethy1 zinc. B) Apparatus. The prinicipal difference between the apparatus used in the present study and that of Tietjen and Amick,8 in addition to size and other related design features, is that RE induction heating is utilized in place of resistance heated furnaces. Induction heating was selected for this application because it appears to have several advantages, including: 1) It is possible to keep all fused silica portions of the apparatus at temperatures well below those of the reaction zone, thus minimizing a possible source of contamination. 2) The thermal mass of an induction heated system can be made small, thus reducing the total time required for the growth process. 3) Sharp temperature profiles (desirable for high deposition efficiency) are easily achieved. 4) The volume of the system for a given substrate area can generally be made smaller than a comparable resistance heated unit. This results in shorter time

Jan 1, 1970

By Norman B. Braly

The following is not offered as an extended paper on the subject of shaft sinking, but more as a description of the present practice of shaft sinking in the Butte district. The Anaconda company is sinking at present the following shafts: Badger State, Moose, Mountain Consolidated, Mountain View, Pennsylvania and Tropic. At the High Ore and Leonard mines the shafts are being deepened by sinking two compartments and will subsequently be enlarged to the full working size by raising alongside the compartments which are now being sunk. The following other companies are also sinking shafts: Butte-Alex Scott, Butte and Zenith City, Boston and Corbin, North Butte Mining Co. (at the Granite Mountain shaft), East Butte Co. (at the Pittsmont shaft), and the Rainbow Lode Development Co. Shaft Timbering. The shafts of the Butte district, generally speaking, are of three compartments arranged in a straight line, and the pump compartment is usually arranged for the use of an auxiliary hoisting cage, as well as for carrying pipe lines and electric wires. The Rainbow shaft is practically square, and of three compartments. The length of the shafts outside of timber will vary from 17 to 22 ft., and the width from 6 ft. 6 in. to 7 ft. Fir timber is used in all shaft work. This may be obtained from the Coast, when it is known as Coast fir, or from Idaho or Montana, when it is known as native fir. The native fir seems to be the tougher wood, but it is hard to obtain clear lumber in the lengths and sizes necessary for shaft work. Some of the shaft timber of the Anaconda company has been treated with creosote as a preservative, but this practice has not come into general use, as the ground of the camp is so heavy that the timbers usually crush before they rot. The size of timber most used for shaft work is 12 by 12 in., while 10 by 12 in., 10 by 14 in. and 12 by 14 in. are used for some of the special pieces around the shaft. The new Leonard shaft is timbered with 14 by 14 in. wall plates throughout.

Jan 1, 1914

By C. M. Haight

The mine blacksmith and drill-steel sharpening shop at the Franklin mine of the New Jersey Zinc Co. is on the surface, adjoining the main shaft. It is a brick building, 51 by 30 ft. inside dimensions, with a corrugated iron roof and concrete floor. .About two-thirds of the steels used are brought up through the main shaft; the remainder through two auxiliary shafts and are carried to the shop by team or truck. At each shaft sufficiently large stocks of sharp drills of various typcs are kept to replace all the dull steels that may be sent up; while at the shop enough sharp drills are kept to replace the dull steels in the stocks kept at the auxiliary shafts. Though this entails keeping a larger number of drill steels in service than might be required by other methods, there is less hurry in the sharpening shop and the steels have a longer period of rest. If a rest from use enables steel to recover from fatigue strains, this method secures that rest. The forms shown in Fig. 1 are supplied to each shift boss in books of 100. These are used to requisition sharp drills from the shaft stocks and cnable the men at the tops of the shafts to sort out the required sizes and to hare them ready to be sent to the various shaft stations. At one of the auxiliary shafts, the dull drills are placed on a platform from which they are dumped into the body of the wagon that takes them to the shop.

Jan 1, 1927

By P. B. Baxendell

The performance of a water-drive reservoir having a gas cap depends primarily on the movement of the gar-oil and oil-water contacts. The movement of the contacts during production depends in turn on fluid withdrawals and how the reservoir pressure changes as fluids are produced from the reservoir; that is, on how effectively the aquifer maintains pressure by replacing withdrawals. inasmuch as pressure changes, fluid withdrawals, contact positions, and produced gas-oil and oil-water ratios are interdependent, the analysis and prediction of the performance of a reservoir produced in a given way must take into account this interdependence throughout depletion. This paper presents an analysis which, within the limitations of the assumptions made, yields an engineering approach to predicting future performance based on reservoir pressure and production history. The most significant assumption is the method of extrapolation of future gas-oil and water-oil ratios. The extrapolation procedure smoothly increases both ratios to preselected values as the remaining oil column undergoes a specified decrease in thickness. This preselection is made on the busis of previous field experience in depletion of similar reservoirs under similar conditions. For computing future performance a vdumebic balance L combined with the differential equation defining pressure distribution in the aquifer to obtain positions of water-oil and gas-oil contacts. From these positions are extrapolated produced water-oil and gas-oil ratios. Reservoir performance can be investigated when oil production rates are dependent upon various factors including the performance of the reservoir itself. Examples of practical application of the procedure are included. INTRODUCTION To predict performance of water-drive reservoirs with gas caps and thin oil columns, it is necessary to describe the motions of the fluids within the reservoir during the entire production period to depletion. These motions depend on the pressure changes and on the withdrawal of oil, gas and water. Production of oil from the oil zone primarily causes water to move in to take its place; production of gas from the cap tends to cause oil to migrate into its place. In addition, the volumes of oil and gas remaining in the reservoir depend on changes in the pressure, since a decrease in pressure causes fluid expansion, gas liberation and oil shrinkage. A method of relating the future pressure to total withdrawals is used to describe the motions of fluids within the reservoir under conditions arising in possible modes of production. The analysis is based on two relationships and will reduce the problem to one amenable to digital computation. The first of these concerns the dependence of the pressure distribution in the entire aquifer furnishing the water drive upon the total reservoir withdrawals. This dependence is dictated by the permeability distribution and the extent of the aquifer; at present, such information is most readily obtained from the performance history by means of the resistancecapacitance reservoir analyzer. The second relation involves withdrawals, pressure in the reservoir, and movement of oil, gas, and water within the reservoir. The analysis is subject to certain simplifying assumptions that are necessary to permit solution of the problem. A comparison of the methods of this paper with those presently practiced is pertinent. One method of analysis is to use the reservoir analyzer to predict reservoir behavior based on aquifer characteristics determined from production history. Inasmuch as the total withdrawal rate depends upon the gas-oil and water-oil ratios, which depend in turn upon, among other things, the positions of the gas-oil and water-oil contacts, these ratios must be assumed in advance. In this paper these ratios are, instead, related to the computed positions of gas-oil and water-oil contacts. Thus, our method can be applied to problems in which the oil production rate is limited by produced gas-oil ratio, or to problems in which it is desired to determine the variable gas injection rate that will maintain the gas-oil or water-oil contact stationary. These problems cannot be worked satisfactorily on the analyzer. Another method presently used is based on a paper by Hurst.' Since his procedure is dependent upon using the solution of the heat flow equation, which requires constant permeability within the aquifer, and our procedure recognizes variations of permeability in

By J. L. Tomlinson, B. D. Lichter

Electrical resistivities 01 liquid Cd-Bi, Cd-Sn, Cd-Pb, In-Bi, and Sn-Bi alloys were measured using an electrodeless technique. The resistivities ranged from 50 to 160 microhm -cm, temperature dependences were positive, and no sharp peaks in the composition dependence of the resistivity were observed. On the basis of these observations, it was concluded that the alloys are typical metallic liquids. The electron con-cent9,ation was calculated from the measured resis-tizlity and available thermodynamic data using a model which attributes electrical resistivity to scattering by density and composition flzcctuations. A correla-tion was shown between the departure of the electron concentration from a linear combination of the pure component valences and the value of the excess integral molar free energy. Calculation of the temperature dependence of the electrical resistivity showed a need for more detailed thermodynamic data in these systems and led to suggestions for improvement in the concept of residual resistivity in the fluctuation scattering model. THE electrical resistivity of liquid metals provides information regarding interatomic interactions and their effects upon structure. In this experiment an electrodeless technique was used to measure the electrical resistivities of liquid alloys of Cd-Bi, Cd-Sn, Cd-Pb, In-Bi, and Sn-Bi, and the results were used with thermodynamic data to calculate a parameter which reflects the tendency toward localization of electrons due to compositional ordering. It was found that the resistivities of these alloys are generally metallic in magnitude and temperature dependence. The electrical and thermodynamic properties are discussed in terms of the fluctuation scattering model'22 which supposes that the electrical resistivity arises from scattering due to a static average structure and departures from the average due to fluctuations in density and composition. Further, this model is compared with the pseudopotential scattering model of Ziman et al.3-5 EXPERIMENTAL PROCEDURES Alloy samples were prepared from 99.999 pct pure elements obtained from American Smelting and Refining Company (except tin which was obtained from Consolidated Smelting and Refining Company.) J. L. TOMLINSON, Member AIME, formerly Research Assistant Division of Metallurgical Engineering, University of Washington, Seattle, Wash., is now Physicist, Naval Weapons Center, Corona Laboratories, Corona, Calif. 0. D. LICHTER, Member AIME, is Associate Professor of Materials Science, Department of Materials Science and Engineering, Vanderbilt University, Nashville, Tenn. This work is based on a portion of a thesis submitted by J. L. TOMLINSON to the University of Washington in partial fulfillment of the requirements for the Ph.D. in Metallurgy, 1967. Manuscript submitted May 31, 1968. EMD Weighed portions were sealed inside evacuated silica capsules, melted, and homogenized before the resistivity was measured. The resistivity of a liquid alloy was measured by placing the sample inside a solenoid and noting the change in Q. According to the method of Nyburg and ~ur~ess,~ the resistivity of a cylindrical sample may be determined from the change in resistance of a solenoid measured with a Q meter as T7--5--W =R7JT^ ='Kc-lm(Y) [1] where L, R, and Q = wL/R are the inductance, series resistance, and Q of the solenoid. The subscript s refers to the solenoid with the sample inside; the subscript 0 refers to the empty solenoid. Kc is the ratio of the sample volume to coil volume and y = 2 [bei'0(br)-j ber'o(br)~\ br\_bero(br) +j bei0 (br) expressed with Kelvin functions which are the real and imaginary parts of Bessel functions of the first kind with arguments multiplied by (j)3'2. The argument of the function Y is hr where r is the sample radius and b2 = po~/p, i.e., the permeability of free space times 271 times the frequency divided by the resistivity in rationalized MKS units. Since Eq. [I] cannot be solved explicitly for p, values of Kc. lm(Y) were tabulated at increments of 0.1 in the argument by. A measurement of Q, and Q, determined a value of Kc . lm (Y) and the corresponding value of br could be read from the table. From the known r, uo,, and w, the resistivity, p, was determined. The change in Q was measured after letting the encapsulated Sample reach equilibrium inside a copper wire solenoid. The solenoid was contained in an evacuated vycor tube in order to retard oxidation of the copper while operating at high temperatures and heated inside a 5-sec-tion nichrome tube furnace capable of obtaining 900°C. Temperature was determined with two chromel-alumel thermocouples, one in contact with the solenoid 30 mm above the top of the sample and the other inserted in an axial well at the other end of the solenoid and secured with cement so that the junction was 2 mm below the bottom of the sample. Temperature readings were taken with respect to an ice water bath junction, and the voltage could be estimated to the nearest thousandth of a millivolt. The lower thermocouple was calibrated by observing its voltage and the Q of the coil as the temperature passed through the melting points of samples of indium and tellurium. The upper thermocouple reading was systematically different from the lower thermocouple reflecting the temperature difference due to a displacement of 60 mm axially and 6 mm radially. Calculations show that the gradient over the sample was less than 2 deg. Q was measured by reading a voltage related to Q from a Boonton 260A Q meter with a Hewlett Packard

Jan 1, 1970