Search Documents

By A. A. Rafiei, J. A. Finch

A previous study comparing n-pentanol and the polyglycol Fl50 showed that the two reagents could give the same gas holdup but with different size bubbles. The finding implies that bubble rise velocity depends on the surfactant (frother) type. A study using bubble swarms supported the frother type effect but bubble interactions were a possible confounding factor. This study resolves the question by measuring the rise velocity of single bubbles of 0.8-2.5mm diameter over a distance :::: 300cm in n-pentanol and F 150. It is shown that at typical frother concentrations used in flotation that the rise velocity in n-pentanol remains comparable to that in water alone while in Fl50 the velocity is significantly reduced. The results confirm the suspected impact of frother type. It is illustrated that in n-pentanol the rise velocity does not reached terminal; while in Fl50 it does and this is the source of the velocity difference. Advances

Jan 1, 2009

By G. Knight

"Results of a program of dust research carried out at the Mines Branch Laboratory, Elliot Lake, indicate that dust-concentration estimates vary greatly, depending on the sampling instrument, the assessment technique and the properties of the dust cloud. The wide range of the ratio between the estimates by any pair of instruments shows that the correlation between the health hazard and dust-concentration estimates by most existing sampling instruments must be questionable. Important studies are being carried out to permit the definition of mine environments in more precise technical terms. The influence of size selection, the physical property measured, composition and sampling period on the assessment of the health hazard are discussed."

Jan 1, 1969

By N. R. Thornton

This paper discusses the rapid growth in the application of instrumentation for metallurgical process control. It covers such methods as ultrasonics, pulp density measurements, on-stream X-ray analysis and reagent control, as well as the expanding use of computer control and data acquisition.

Jan 1, 1971

By E. De Souza

Energy associated with ventilating an underground operation comprises a significant portion of a mine operation's base energy demand and is consequently responsible for a large percentage of the total operating costs. Ventilation systems may account from 25?40% of the total energy costs and 40?50% of the energy consumption of a mine operation. Fans are the most important mechanical devices used to ventilate underground mines and the total fan power installed in a single mine operation can easily exceed 10,000 kW. Investigations of a number of mine main fan installations have determined their assemblage to be, in general, very energy inefficient. The author has found that 40?80% of the energy consumed by a main fan is used to overcome the resistance of fan assemblage components. This paper presents how engineering design principles can be applied to improve the performance and efficiency of fan installations, resulting in substantial reductions in power consumption, operating cost and greenhouse gas emissions. A detailed case study is presented to demonstrate that, by designing fan assemblages using proper engineering concepts of fluid physics and industrial ventilation design, main fan systems will operate at efficiencies well above 80?90% (compared to common operating efficiencies of between 20 and 65%), resulting in a drastic reduction in a mine's overall costs and base electrical and energy loads.

Aug 1, 2013

By Su-Ping Peng

Three dimensional (3D) seismic exploration has been carried out since the 1980s in the mining district of China, where it has been playing an indispensable role in the high yield and efficiency of coal mining. Unlike oil exploration, this technique uses high density seismic acquisition technology. In recent years, it has focused on wide azimuth 3D seismic acquisition. Evaluation of geometry moved away from depending on folds, azimuth and offset, toward being based upon a focus-ray beam. Conventionally, coalfield 3D seismic interpretation focused on time domain and was based on kinematics information, which is only suitable for less complex geological conditions. To achieve high-resolution processing for the complex topography and structure in coalfields, data processing shifted from poststack to prestack. The means to improve the accuracy of interpretation for complex geological conditions are 1) integration of multiple attributes and multiple disciplines, 2) combination of seismic and geological data, and 3) comprehensive combination of time domain and depth domain data. With the demand for lithological exploration, high-resolution data processing must also take into account the requirements of preserving amplitude in seismic data. Seismic attributes technology, seismic inversion technology, and dynamic tracking interpretation are key techniques in 3D seismic exploration. They greatly improve interpretation accuracy, produce better results in the goaf space description of the coal-bearing strata and coal seam structure, and effectively reduce exploration costs under complicated geological conditions. Therefore, these techniques will be the primary means employed in the future to deal with coalfield complex structure and lithological exploration.

Aug 1, 2013

By B. Arlyuk

On the basis of research of relations among the market participants the analytical model has been created which connects the price of industrial good at stock exchange with volume of sales and the stock of the sellers and buyers, Also a model was developed for assessment of these parameters of the market status by the actually fixed stock exchange and general market indicators. The composition of these models made it possible to create reliable system of short-term price forecasting for commodities or base metals up to one quarter ahead. Imperfectability of creation a model for reliable price forecasting by purely statistic methods (by the "black box" principle) was shown. A model of price behavior qualitative forecasting till one quarter ahead has been developed, which determines the probability of reaching in future of the given level as well as of the price maximums and minimums, Optimal values of threshold probability were determined for forecasting the future price maximums and minimums securing the maximum profit from the forecasting system application for commercial activity. The developed system of forecasting was identified for primary aluminium at the period of 1990-2003. The system was tested daily during 20 months period for speculations on 3M primary aluminium forwards at London Metal Exchange with high commercial result.

Jan 1, 2004

By X Dai

This paper investigated the loss of cyanide via oxidation in CIP or CIL processes by relating the cyanide oxidation to its major oxidation product, cyanate. The results showed that the oxidation of both free cyanide and copper cyanide complexes are substantially enhanced by the presence of carbon. The rate of cyanide oxidation was found to occur in the order: Cu(CN)32- > CN- > Cu(CN)2-. The cyanide oxidation rate in the presence of copper and carbon increased significantly with increasing dissolved oxygen concentration, typical of CIL vs. CIP conditions. Cyanide oxidation rate of iron, zinc or nickel cyanide complexes was minimal.

Jan 1, 2011

By William Hawker, James Vaughan, Jeff Chen, Antony van der Ent

"Nickel agromining utilizes hyperaccumulator plants (“metal crops”) to extract nickel from low-grade soils, a process that yields high-grade nickel bio-ore. This feedstock is further processed into a range of nickel products. The bio-ore is relatively free of impurities that complicate the traditional processing of laterite nickel ores. In this paper, current primary nickel processing routes and proposed nickel bio-ore processing options are summarised. A novel pyro-hydrometallurgical route demonstrated at the laboratory scale is described. This process produces a precipitated nickel hydroxide product and takes advantage of the water-soluble basic compounds in the ash to minimise reagent requirements, thereby making it suitable for small-scale implementation in close proximity to the nickel farm. In this process, nickel is precipitated from the leach solution using the basic ash wash liquor. Leaching nickel from ash generated from open air burning requires strong acid and long residence times to obtain high recoveries due to its complex nature and distribution of nickel in multiple phases. This process can be improved by optimising the ashing process with respect to nickel leachability.INTRODUCTIONHyperaccumulator plants have the unique capacity to ‘biopurify’ and concentrate certain trace elements (e.g. nickel) from the soil into their biomass (Reeves 2003; van der Ent et al., 2015). Cultivating these plants as ‘metal crops’ by periodically harvesting and incinerating their biomass generates a high-grade bio-ore (Chaney et al. 1998; Li et al. 2003). This process is called phytomining or ‘agromining’ which is an emerging technology for extracting nickel from sub-economic resources (van der Ent et al., 2015). Potential near-term applications of the technology include implementation on land ahead of processing of the underlying ore-body (Willis 2015), as a mine-site rehabilitation strategy or as an alternative crop for farmers on land that is not suitable for normal food crops. In the longer term, nickel agromining could provide a significant supplement to the nickel supply chain. Critical to the success of agromining is effective bio-ore processing. Due to the unique chemical composition of this feedstock material, existing processes are not very efficient. Our current research efforts aim to develop new process options that overcome limitations of previously trialled routes. In this paper we summarise conventional nickel process routes and proposed new options for producing agromined nickel."

Jan 1, 2016

By C. Stapel, I. C. Tânczos, R. J. De Meijer

"Abstract -In recent years the Environmental Research Group of the KVI has been developing a number of radiometric techniques that may be employed in mineral sand exploration. These techniques involve: radiometric fingerprinting for assessing sand provenances and mineralogical composition; thermoluminescence for dating and provenance determination of sediments; a towed seabed detector to map seafloors for radiogenic heavy minerals and assessing heavy mineral volumes; and simplified transport mechanism models to explain and predict heavy mineral concentrations.All techniques exploit the property that heavy minerals as a group contain concentrations of naturally occurring uranium and thorium that are a hundred to a thousand times higher than in light minerals. In this paper the physics of a number of methods will be described together with a number of results. Based on these results potential applications to mineral exploration and mining are discussed."

Jan 1, 1994

By H. Arima, Y. Kudo

In general, the iron content of zinc leach residue produced by sulphuric acid leaching from calcine is disposed as jarosite or goethite into a tailing dam. More recently, these iron residues have been treated pyrometallurgically to avoid waste disposal. The Iijima refinery selected a different zinc leach residue treatment process for iron control when it was established in 1971. The Iijima refinery is the only plant in the world that has processed a zinc leach residue by the combination of SO2 pressure leaching and O2 pressure hematite precipitation. The process enhances zinc recovery and recovers gold, silver, copper, lead and rare metals in saleable by-products. This paper focuses on the two stages of autoclave application in the zinc leach residue treatment process. The detailed flowsheet and recent advancements to improve the quality of by-products are discussed.

Jan 1, 2004

By N. R. Andrade-Gonzalez

In this paper, the effect of magnesium and strontium additions on the heat treatment behaviour of cast A319,2 alloy was investigated, Permanent mold samples were heat treated at 495 °C for 4 and 24 h, then quenched in hot water and aged at 180 °C and 220 °C for different temperatures, It is found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu alloys, mainly when Mg and Mg-Sr are added, The results of electron probe microanalysis (EPMA) observations reveal that the age-hardening behaviour is related to the precipitation sequence of alloys, For the Al-Si-Cu alloy, the first aging peak is the result of the high-density GP zones, while the subsequent peaks arise from metastable phases, Obvious intervals during the transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks, It is seen that addition of Mg (-0,40 wt %) leads to the precipitation of coarse Al5Mg8SioCu2 particles. When modifying the high Mg alloys, Cu-intermetallics segregate in areas away from the growing Al-Si eutectic regions, Modification with strontium retards the precipitation of the silicon out of the matrix.

Jan 1, 2005

By M. van de Vijfeijken

This paper will first give a short overview of the Copper Mountain project in British Columbia, which just has started commercial operation earlier this year. The grinding process with one 34' x 20' SAG mill and two 24' x 39.5' ball mills will be briefly discussed. All three mills are gear driven by a ring gear, dual pinion and two low speed synchronous motors. Copper Mountain has installed on all three mills, the new state-of-the art dual pinion mill drives. All the inherent operation and maintenance features of this drive technology will be discussed, as well as the advantage of having variable speed control also on the ball mills. The installation and commissioning of the mills and drives at Copper Mountain will be briefly reviewed. Finally the first field measurements on these low speed mill drives will be presented, with the main focus on the low mechanical stress impact of these mill drives on the pinion and ring gear, as well as the accuracy of the load sharing between the two motors.

Jan 1, 2012

By F. Azgomi

A possible way to characterize (classify) frothers using gas holdup as a surrogate for bubble size was explored. Nine surfactants with a range in chemical structures were selected and tested in a bubble column instrumented to measure gas holdup and superficial gas velocity. A correlation between frother type and gas holdup was observed: for alcohols, gas holdup increases with hydrocarbon chain length and the effect is the same whether the chain is branched or straight; for polyglycols, gas holdup increased with number of propoxy groups. The ranking by gas holdup gave the same result as other frother characterization techniques.

Jan 1, 2006

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB?s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By K. Szczesny

This paper considers the integration of uncertain real-time logistics data for reactive construction scheduling. In order to manage a construction project efficiently, an accurate schedule representing the current project progress is inevitable. The quality and up-to-dateness of such a schedule depends on the availability of real-time data. Typically, real-time logistics data contain information about the availability of material, equipment and personnel as well as delivery dates and site conditions. The accuracy and inherent uncertainty depends on the location where the real-time data was acquired. Currently, the integration of such data into a construction schedule is a very time-consuming, manual and, thus, errorprone process. Therefore, this paper proposes a methodology that enables an automatic integration of such uncertain data into construction schedules. By integrating uncertainties into the existing schedule their impacts on the construction work can be evaluated. For this, discrete event simulation is applied. In order to model uncertain input parameters for simulation models this methodology applies the fuzzy sets theory. In combination with alpha-cut sampling technique, discrete model input parameters are obtained. By applying reactive scheduling with several discrete event simulation experiments, the results can be used to modify construction schedules according to agreed timeframes and costs. In order to demonstrate and validate the presented approach an example is conducted.

Aug 1, 2013

By A. Demers, M. Chapman, N. Reynier, R. Lastra, M. Courchesne, C. Laviolette

Historic medical isotope production at Canadian Nuclear Laboratories (CNL) in Chalk River involved the dissolution of irradiated isotope targets prior to extraction of Mo-99. This process generated liquid waste that was cemented in 5-gallon containers and transferred to an outdoor waste-management facility for intermediate storage. Research was undertaken to develop an innovative method for uranium, mercury and cesium recovery from the radioactive cemented waste (RCW). Regulations prohibit the removal of active radioactive waste from the Chalk River facility. Thus, CanmetMINING produced surrogate material following the same procedures and conditions to those used at CNL. The selective recovery of the uranium from the surrogate radioactive cemented waste (SRCW) could offer CNL more disposition options for the resulting wastes. Leaching tests were performed using four different SRCW at 1 kg scale. Different conditions, operating parameters, and the presence of plastic and corrosion products were evaluated on solubilization. The research investigated the use of potassium iodide with the sulphuric acid leach to increase metals recovery. Iodine improves the solubilisation of metals and the U dissolution reached 99%. The increase of leaching time reduces the U solubilization due to silica gel formation. Therefore, it will be important to control leaching time to avoid the loss of U during the pilot scale experiments. For Hg, the solubilization ranged from 60 to 80% due to the presence of metallic mercury and mercury sulphide found in SRCW cured at 60°C and/or aged for 30 months. Ion exchange (IX) was found the best method to separate the uranium from the impurities and produce a purified and concentrated uranium solution suitable for yielding a uranium product (yellow cake).

Jan 1, 2020

By A. Tabereaux

The reduction of perfluorocarbon (PFC) emissions from aluminum electrolytic cells is a key issue in reducing greenhouse gases at all aluminum smelters, The emission of tetrafluoromethane (CF4) and hexafluoroethane (C2F6) gases during anode effects at smelters can be calculated using two different methods; anode effect-minutes slope and anode effect overvoltage, This work demonstrates that the optimum method depends to a large extent on the type of anode effect kill algorithm utilized at each smelter, CF4 emissions vary widely from aluminum cells depending on the type of anode effect kill method utilized; fast, aggressive anode bridge movements vs. slower, moderate anode bridge movements.

Jan 1, 2005

By A. Azizi, P. Blatter, A. Bouajila

ABSTRACT In-situ monitoring of gold dissolution by means of a rotating electrochemical quartzcrystal microbalance unveiled dramatic decreases in gold leaching from sulphide-rich ore after 360 minutes in an actual cyanidation circuit. Pre-oxidation was effective in enhancing gold extraction by preventing a passive film from forming on gold surfaces. This work aims to highlight efforts undertaken to determine (1) how gold cyanidation is limited by passivation, (2) what reactions and mechanisms are involved during sulphide-rich ore cyanidation, and (3) how peroxidation efficiency of an industrial sulphide ore is controlled by galvanic associations between its sulphide constituents.

Jan 1, 2013

By G. P. Gu, B. Fang, R. W. Revie, M. Elboujdaini

Stress-corrosion cracking (SCC) tests were conducted in the near-neutral pH standard solution, NS4, and in an actual soil solution, using four-point bending at high a stress ratio and low frequency conditions very similar to those of operational pipelines. Pitting incubation appeared first and then pitting initiated and grew in both solutions although there were many more pits on the specimen tested in soil purged with 5% CO2 + 95% N2 than in the specimen tested in NS4 solution purged with the same gas. These observations show that samples in soil solution are more susceptible to pitting than those in NS4 solution. When the pit reached a critical size, the increased stress concentration around the pits, resulted in the transition to a crack.

Jan 1, 2005

By R. J. Enkin

Modern mineral exploration depends on multidisciplinary 3-dimensional integration of geological and geophysical data. Identification of the geological sources of geophysical anomalies requires knowledge of the physical properties fingerprint of rock types, formations and their alteration products. Understanding how and why rock physical properties vary within the Earth's subsurface ensures that appropriate geophysical exploration methods can be chosen, and allows for more efficient and effective surveys to be designed. Physical properties knowledge is integral to geophysical modeling - measured data or values estimated based on geological understanding are used to produce realistic forward calculations and to constrain inversion models. Mira Geoscience and the Geological Survey of Canada, in collaboration with industry and academia, are building a Rock Properties Database System (rpds.mirageoscience.com). It compiles the most valuable physical properties for mineral exploration (density, porosity, magnetic susceptibility and remanence, electrical resistivity and chargeability) linked with location and lithological metadata. A critical knowledge gap, addressed in this study, concerns the dependence of physical properties on alteration and mineralization processes. We report on the results of a collaborative University of British Columbia - Geoscience British Columbia project, ?Integrated Geological & Geophysical Porphyry Models: Adding Value to Geoscience BC Geophysical Data?. As part of the QUEST and QUEST-West geophysical initiatives, Geoscience BC focused detailed geophysical surveys on a suite of six known porphyry deposits: Mount Milligan, Endako, Huckleberry, Bell, Granisle, and Morrison. Physical properties for a set of 269 samples of characteristic host rocks and their altered equivalents were measured. The causes of physical properties variations were investigated through their correlations with ore and alteration mineralogy determined from thin-section observations and X-ray diffraction analyses. Physical properties of variably altered host-rocks and intrusive rocks vary significantly between different BC porphyry deposits. No specific unifying geophysical model exists that can be uniformly applied during exploration. Knowledge of local background geology and local physical properties variations is necessary as host-rocks and intrusive rock compositions vary depending on magmatic affinities, and alteration styles will vary reflecting host-rock compositions, crustal depth and influence of meteoric water. A district-scale exploration strategy requires location of intrusive bodies, which are commonly magnetic, resistive and low in density. Correlations should not be expected between density and magnetic susceptibility, because alteration may lead to magnetite destruction or to secondary magnetite development. Deposit-scale ground geophysics might image potassic alteration zones that can be magnetic in both alkalic and calcalkalic systems. Low magnetic susceptibilities, resistivities and densities might aid in locating the typically more porous phyllic and argillic zones. All geophysical data must be interpreted with background knowledge of local rock types and in light of the expected deposit model and associated magmatic and hydrothermal processes. The most effective means to building physical properties knowledge prior to geophysical investigation remains collecting rock physical properties measurements. The cost of rock properties data collection is low, relative to the overall costs of running a mineral exploration program, and can provide an important framework for design of geophysical surveys, survey method selection, geophysical modelling, and data interpretation.

Aug 1, 2013