Search Documents

The application of methods using large diameter down holes has become an important facet in both the development and stoping operations of mines within the Aberfoyle group. Holes of up to 98 metres (vertical) and 78 metres (inclined) have been successfully used in stoping operations. A number of rises have been developed to meet ventilation, servicing and escape-way requirements. The most ambitious rise to date has been a..vertical 93 metre long by 4.50 metre square ventilation rise. Although some early problems were experienced, the ultimate successful completion of this rise has enabled the technique to be incorporated with confidence in future mining plans. This paper summarises experience in long hole rising techniques, their evolution from the original cratering concepts, and the approach to further development of these techniques.

Jan 1, 1982

By OÆBrien D. R

Up until June 1988, Mount Thorley Coal Handling and Preparation Plant disposed of tailings by two methods. Approximately half of the plant tailings was mechanically dewatered by solid bowl centrifuges mixed with plant reject and was subsequently disposed in mine overburden spoils; the remainder was pumped to tailings ponds. Both future mine planning and environmental constraints could not allow for the long term construction of more tailings ponds so, following evaluation of available dewatering technology, belt press filters were selected for the treatment of tailings in excess of the capacity of the existing solid bowl centrifuges. Commission of the four 2.5 metre wide belt press filters soon showed that marked differences in performance were experienced when treating different coal seams. Further analysis showed that the coal tailings from different seams were quite different in terms of clay mineralogy, and these differences could be correlated with varying degrees of filter performance. Poor filter performance was experienced with coal tailings rich in sodium montmorillinite clays. A number of variables were investigated including in-line mechanical mixing of flocculant and feed slurry, cation exchange reagents such as gypsum, and upstream addition of cationic flocculant. In order to achieve satisfactory performance on the worst tailings, a combination of all of the above was required. In this paper, the reasons for selection of belt press filters and the program of investigations and testwork required to arrive at satisfactory belt press filter performance for the treatment of troublesome bentonitic rich tailings are discussed.

Jan 1, 1989

By Smith PE

The main components of face design are the power loader, face conveyor and powered support system and the interaction of these components determines the effectiveness of strata control. A major influence upon the interrelationship of this equipment is the geological environment, of which seam thickness appears to play an important role. Recent thick seam experience indicates a significantly different characteristic behaviour pattern from that observed in thin seams The structural integrity of the face wall is particularly influenced by seam discontinuities such as natural joint planes and mining-induced fractures in the yield zone ahead of the faceline. In addition, the presence of stone bands or dirt partings in the seam offers interfaces for uncontrolled release of blocky material. Some case study experience at British collieries provides a comparison with performance data at a specific location, that highlights the importance of coal face layout and design.

Jan 1, 1986

By Miles M. J, Sandy D. A

It has long been known that drilling and blasting operations have a direct influence over productivity and costs of subsequent operations. If mine management is to effectively optimise blasting operations, good information is required on the operating costs of each of the affected operations, together with knowledge of how they are influenced by blasting. In practice it is not possible to do enough repeats of a full scale production blasting experiment to make a statistically significant analysis of the results. By monitoring each blast and subsequent operations in as much detail as possible, enough data will be available to effectively measure the effect of blasting on costs. This gives management an insight into the blast performance and is the first step towards optimisation. An Integrated Blast-related Cost Reporting System has been developed at the Rossing Mine Open Pit, which calculates the total mining cost for each blast. In assessing the total mining cost for each blast, use was made of an.integrated planning and management information system to collect relevant production variables, current operating costs and survey data. An automatic image analysis system was employed to measure the fragmentation of the blasted material in the back of haul trucks. A shovel monitoring system is also under development for use in assessing the muckpile diggability and, in conjunction with an appraisal of shovel component reliability, to estimate the maintenance cost under various digging conditions.

Jan 1, 1990

During the last few years the quality requirements on roads and railroads have become more accentuated due to the desire to minimise maintenance costs. This has, in turn, led to increasing requirements in the preparation of ballast materials and pavement aggregates. As the access to natural gravel in northern Europe is decreasing (due to lack of availability or by law restrictions) the use of crushed rock material is becoming more and more important. The aim of this paper is to derive and describe a universal method for the prediction of particle size distributions from compressing crusher machines such as jaw- and cone-crushers. Based on a closely defined physical model, expressions which define the size reduction process are derived. Conditions for simplifying assumptions are clearly outlined. The choice and mix of breakage functions is a central subtopic iò the analysis of the crusher machine processes. Known breakage functions are reviewed and evaluated. A new concept for determination of a true breakage operator which is related to physical properties of the crusher device and the size distribution of the feed material is introduced. Finally experimental tests are compared to numerical calculations. The method described in the paper can be a useful tool when designing crushing plants or when optimizing the output of compressing crusher Machines.

Jan 1, 1995

By Sandvik

Fine grinding in an air-swept ball mill working in closed circuit with a forced vortex air classifier has been investigated first in continuous laboratory and then in industrial scale. Results from the laboratory circuit have shown significant influence of mill load (powder filling) on the capacity of the circuit. In laboratory scale the mill load was measured and controlled by a weighing platform placed under the complete mill set-up. The mill load of the industrial air-swept ball mill has till now been controlled by measuring the power consumption of the mill motor. Thus, it was necessary to operate far from the range of optimal mill filling. To improve the circuit performance, alternative ways of mill load measurement were investigated. An important factor was investment cost, as many fine grinding mills operate in relatively small circuits that do not wan-ant large investment. In this case the task was accomplished by using a piezoelectric strain transducer, which detected strain changes in the mill shell. It was installed in the midpoint of the shell, where the highest deformation was obtained. As the transducer was on the top position, it indicated compression, and on the bottom position it measured tension. By taking the difference between the readings, it was possible to calculate total strain variations, directly proportional to the mill load. The signal from the transducer was sent to a control room via a cordless infrared communication system, employing a microprocessor control card, which could further regulate other operating parameters of the circuit according to the software model. The installation required very low investment cost and provided simplicity of application as well as stability and reliability of characteristics under severe industrial condition. The measurement system made it possible to optimise the mill load and thus increase the production from 3.2 to 3.7 dh (15 per cent), and stabilise the circuit operation.

Jan 1, 1995

By Jones A

Today there is a vast amount of information available relative to the performance of tunnel boring machines, and associated systems. The data referred to here consists of project reports, manufacturer's equipment literature and papers concerning almost every aspect of the excavation process. Why is it then, that many projects that employ full face tunnel boring machines (TBMs), on average perform significantly less than the peak performances reported in this industry?

Jan 1, 1993

By Bukovinsky SB

The smelting, refining and hydrometallurgical operations practised in the winning of non-ferrous metals are associated with severe aqueous and high temperature corrosion problems.With the increasing costs of maintenenace and the utilization of computerization to control the processes, the trend in recent years has been to spend more capital on improved and proprietory grades of engineering materials, which offer greater reliability and more cost effective plant performance.The problems which have plagued stainless steel users for many years are the alloys' poor performance in chloride or other halide media where pitting, crevice or chloride induced stress corrosion cracking may occur, have been essentially solved by the new proprietory grades. The controlled additions of minor alloying elements including rare earth metals have led to the development of stainless steels with high mechanical strengths, improved corrosion resistance, and high temperature corrosion resistance and structural stability.

Jan 1, 1985

In order to satisfy environmental and mine operational requirements it is becoming increasingly important to minimise ground blast vibrations at certain locations. These locations are often in soil or on large resonant structures such as grain silos, highway bridges or even the walls of an open pit. A soil monitoring exercise was carried out to evaluate the common practice of coupling vibration detectors to the ground using spikes. At a series of locations in an operating quarry the spiked array response to single blastholes was compared with that of an accelerometer array attached to a calibrated embedded mount. The results clearly showed that the spiked arrays over-estimated the true ground vibration by 46.5 per cent on average, with a maximum observed error of 99.2 per cent. These errors are considered too large for compliance monitoring where accurate vibration levels are required for comparison with prescribed limits. Although spike coupling is convenient, its use for compliance monitoring should be viewed with caution. Unfortunately, however, many manufacturers supply their detectors as spiked arrays. A structural monitoring exercise was also carried out to evaluate the vibration response of a grain silo, highway bridge and a pit wall to the initiation of single blastholes. In this case accelerometers and standard geophones were firmly attached to the bridge which resonated at low frequencies. The results clearly show that, due to their limited low-frequency response, the geophones typically measured only half the true vibration level as measured by the accelerometers.

Jan 1, 1995

Brunswick Mining and Smelting Corporation Limited operates a large base metal property near Bathurst, New Brunswick in eastern Canada. Nominal capacity for the underground mining operation and concentrator is 10 250 DMT/day. Four concentrates are produced by differential flotation technology to recover minerals containing copper, lead, zinc and silver. Two characteristics of the Brunswick ores have a major impact on mineral processing operations. The mineralogy of the ore is complex with a total sulphide mineral content of 85 per cent. In addition, the ore is extremely fine-grained, and satisfactory liberation is difficult to achieve. These characteristics directly influence flotation selectivity and thereby affect metallurgical performance. Significant improvements in metallurgical performance have been achieved through the application of basic grinding and flotation principles using conventional milling equipment. Current operating practice and the metallurgical advancements are detailed.

Jan 1, 1993

By Van Heuzen JA

The extensive deposits of brown coal in the Latrobe Valley form the major solid fuel resource in Victoria and are the energy source for most of the State's power generation. This paper describes the coalfield resources allocated for electricity generation and a potential sequential develop- ment of these areas in future years to supply future power stations.

Jan 1, 1982

By Chaves AP

This paper describes an investigation on the surface properties and mechanisms involved in the agglomeration of iron ore. For this purpose, an organic binder (carboxyl-methyl-cellulose (CMC)) was used in substitution of bentonite, the classic binder in iron ore concentrate agglomeration. Recently, a renewed interest of the iron ore producers in Brazil to replace bentonite for an organic binder, because of the economy that can be achieved in the, blast furnace operation. These savings are mainly due to the lower aluminum silicate addition which decreases slag volume and the improved pellet metallurgical properties which have the potential for lowering hot-metal production costs. Also organic binders are effective at lower addition levels, which results in lower storage and transportation costs. It is very important in Brazil because of the vast geographical area since transportation is made mainly by truck. Another advantage of organic binders is that they have low ash contents, and therefore most of the binders bum. off during the pellet firing operation. Previous studies have demonstrated the possibilities of the use of CIVIC, but in addition to its high cost, the pellets presented improper behavior at high temperatures or when prepared with high moisture levels. In the investigation here described, these problems have been solved through the addition of other reagents to CMC.

Jan 1, 1993

From the mid-1970s ZC Mines at Broken Hill had a policy to increase ore production rates at progressively lower head grades. In the mid-1980s the mine suffered crippling losses at a time of low metal prices. An important contributory factor was the inherent geological distribution of metal grades in the seven defined ore lenses. Grades are bimodal, and perhaps, trimodal, in each ore lens. There is a tonnage deficiency in the critical cut-off grade zone of 7-10% Pb+Zn. Lowering the cut-off grade introduced siliceous and pyrrhotitic material which resulted in significantly poorer metallurgical performance. This example shows that the mine geologist needs to know the grade distribution of the orebody and to convey clearly the downstream implications of changes in the head grade.

Jan 1, 1990

Developments in furnace construction and design have been very rapid in recent years. Larger furnaces operating at high top pressures with much improved burdens are giving extremely high production rates. Modern scientific techniques and the use of computer control are contributing to these Rates.

Jan 1, 1972

By Cox LT

A short term tyre study of trucks operating in a multiple pit surface coal mine showed significant potential for cost savings. The tyre study, conducted on-site over a three months period covered a mixed fleet of 18 trucks ranging from 27 tonne to 77 tonne capacity operating on overburden removal, coal haulage and watering duties. Some existing plant history records and a variety of tyre related measurements during the course of the study allowed the current state of tyre operations to be quantified. Specific attention was given to determining ger>ral trends from historical records and conducting detailed studies of individual lug damage, pressure monitoring and rectification, as well as tyre maintenance procedures. Important haul road parameters including camber, gradient, curve radii and superelevation, constructional materials and surface clean-up were appraised for their influence on tyre wear. Recommendations for achieving long term cost effective tyre utilisation included increased tyre maintenance, personnel development, compliance with haul road design parameters and more stringent clean-up Procedures.

Jan 1, 1982

By Fuller T

This paper introduces the technology used in laser surveying systems, and the development of a reflectorless one-man total station. These systems are being used for applications such as blast pattern surveys, face profiling, muckpile surveys and the general survey of inaccessible areas. Black Diamond Solutions is continuing to assess new technology and develop integrated systems for applications in the mining industry.

Jan 1, 1995

By Chenggang W, Junhua D

Fragmentation variation laws in loading and non-loading areas are obtained by cement block model blasting experiments under various stemming lengths. A reasonable ratio between loading length and stemming length is worked out according to minimum average fragment size. The present continuous loading structure, for its very long length to be stemmed, leads to insufficient fragmentation in the upper part of bench. So a new loading structure with bottom air cushion is put forward. The author analyzes blasting effects and processes of two loading structures' and proves that there exists a optimal length of air cushion.\

Jan 1, 1990

In the last 40 years nuclear energy has taken its place as a major source of electricity worldwide. It now produces 17 per cent of the world's electricity and could conceivably produce a higher proportion, to displace some six billion tonnes of carbon dioxide emissions per year. Concerns about global warming and environmental quality now underline the virtues of nuclear electricity among alternative sources of energy. Global electricity demand is rapidly increasing as a proportion of total energy usage. The proportion has doubled since 1960 and the demand is expected to increase at least 75 per cent between now and 2020. The source of this extra capacity, and the replacement of present capacity, raise questions with major resource and environmental implications. Today nuclear energy is a mature technology. Over 1200 nuclear reactors have been built and operated, some of these have been decommissioned, and among the 440 reactors in commercial operation the first advanced reactors are now entering service. Some 8000 reactor-years of operation have, with the sole exception of Chernobyl, shown nuclear energy to be extremely safe and reliable. High-level wastes are being managed properly and in different parts of the world two strategies are applied to this. Australia has a major role as a long-term supplier of uranium, since it holds almost 30 per cent of the world's reserves. This, along with an impending sellers' market for uranium, is making it an opportune time to develop new mines here. However, after several decades of concern about civil nuclear energy contributing to the arms race, we now have uranium liberated from nuclear weapons stockpiles being diluted for use in civil reactors, which will supplement ex-mine supply. The public acceptability of nuclear energy remains the critical factor in its future and hence in ours.

Jan 1, 1997

Creating Value and Improving Environmental Performance by the Recovery of Valuable Products from Tailings from the Athabasca Oil Sands in Alberta, Canada

Sep 13, 2010

Recent work on computerised mineral resource databases at the Institute of Geological and Nuclear Sciences Limited has concentrated on the development of the GERM, REGCHEM, and MINLIT databases, and their integration in a Geographic Information System using MapInfo software on an IBM-compatible microcomputer local area network. GERM (GEological Resource Map) is a mineral deposit inventory with national coverage and more than 10 300 entries. REGCHEM (REGional Exploration GeoCHEMistry) is a database of stream sediment analyses from open-file mining company reports, containing more than 14 000 sample sites from the Coromandel and west Nelson regions. MINLIT (MINeral LITerature bibliography) is an annotated bibliography of literature on topics relating to the exploration and geology of mineral deposits in New Zealand, and includes more than 5000 entries for published books and papers, and unpublished mining company reports, university theses, and government reports. Master sets of GERM and MINLIT continue to be maintained on a VAX mainframe network but REGCHEM is operated only in the PC environment using the Microsoft ACCESS database management system software.

Jan 1, 1993