Search Documents

Discussion of the paper presented at the Manchester Geological and Mining Society's general meeting held in Manchester, April 11th 1916, with Mr. Leonard R. Fletcher, President, in the chair, included questions asked and points for discussion raised by Bramall V., Paton J.D., Fletcher L.R., Siddall F.N., Stoker A. and Stone T., in particular on how to eliminate dust

Dec 1, 1916

By J. H. E. Jeffes, K. T. Jacob

The activity coefficients of oxygen in liquid Pb-Sn alloys have been measured between 550 and 1100°C by use of solid oxide galvanic cells: Pt, Ni-NiO | Zr02 Solid electrolyte | O (Pb + Sn), Cermet, Pt; and Pt, Fe-FeO | Zr02 Solid electrolyte | 0(Pb + Sn), Cermet, Pt. Alcock and Richardson's quasi-chemical equation, with the coordination number of atoms set to 2, is found to predict successfully the activity coefficients of oxygen in these alloys. The relative partial molar enthalpy and entropy of oxygen at 1 atom per cent in the alloys have been calculated from the variation of the activity coefficient with temperature. The addition of Sn to an unsaturated solution of O in Pb is shown to decrease significantly both the partial molar enthalpy and entropy of O. As the measurements were restricted to a narrow range between 750 and 1100°C in Pb-rich alloys, however, the pronounced variation of the partial molar enthalpy of O with temperature at constant alloy composition predicted by the quasi-chemical model could not be verified.

Dec 1, 1971

By R. R. Hart, R. A. Evans

This paper outlines the the methods currently being used in the West Wales Area for preventing the occurrence of any outbreak of spontaneous combustion. Stress is placed on the importance of correlating the position of a Rider Seam which is prone to spontaneous combustion. The recent introduction of the UNOR Recorder has contributed to the ability to monitor the CO content of the general body of the air during any incident. The use of modern sealants and improved methods of applying them have enabled the few instances of spontaneous combustion in South Wales to be treated promptly and efficiently. The authors describe the current spontaneous combustion problems at two collieries.

May 23, 1905

By J. Coxon, G. W. Walker

The paper describes the discovery, location and events concerning three types of heating which have occurred in recent years: a) in a district being salvaged, b) in the shaft pillar at an air-crossing, and c) in the gate side of a production district, all of which have occurred in the Beeston Seam at collieries in the deeper eastern part of the area. The paper describes the precautions, air sampling arrangements, training methods and codes of practice which have been adopted at collieries where spontaneous combustion is, or is likely to be, a hazard. The air samples taken from behind the stoppings following the sealing off of the salvaging district are examined and interpreted. The problem of effectively sealing off where more than two stoppings are required is made apparent. Other lessons have been learned as a result of these heatings and are described in the paper.

May 23, 1905

By F. Reich, S. L. Chryssoulis, K. G. Stowe

The surface chemistry of particulates from mineral processing streams can be determined by laser-probe microanalysis. The small area of analysis (2-30 micrometres) enables the surfaces of individual grains to be characterised. Conclusions are based on data acquired from a statistically significant number of grains of a given type. Maps showing the distribution of elements on the surface of mineral particulates can be obtained by time-of-flight secondary ion mass spectrometry. The importance of such analyses in understanding the response of minerals to beneficiation practices is discussed with reference to three examples. The first relates to the loss of selectivity in the differential flotation of a base-metal ore, the second to the different flotabilities of coarse- and fine-grained pentlandite from a Cu-Ni ore and the third concerns the preg-robbing effects of organic matter in a carbonaceous gold ore.

Jan 4, 1992

By B. Sonmez, B. Aksanl, S. Ersaym, I. F. Erkal, S. L. Ergun

The comminution circuit at the plant has experienced severe problems arising from a feed containing much larger amounts of clay and having a higher moisture content than expected. Three solutions were proposed: replacement of the crushing circuit by tooth roll-type crushers; using washing drums; and introducing primary autogenous/semi-autogenous millling instead of crushing. Computer simulations studied the effects of the first two solutions on the circuit capacity. Laboratory and industrial scale ball mill batch grinding tests were carried out. The parameters of a kinetic model were determined. The ball mill circuit was sampled and operating model parameters were calculated. The ability of batch grinding parameters to represent the operating conditions was studied. Tests failed to find acceptable model parameters, but parameters from an industrial size batch mill were found to be suitable for simulation studies. The simulations indicated that a continuous feed of -12 mm provided by tooth roll crushers would maintain the desired capacity. Increasing the feed size to -25 mm would reduce the capacity by 8-15%. The use of washing drums could also solve the capacity problem, but small fluctuations in water flow rates might result in problems of excess water in the grinding circuit.

Jan 4, 1993

By Hirsch H. H.

The paper, presented at the North of England Institute of Mining Engineers' general meeting held in Newcastle-upon-Tyne on 12th February 1916, gives a short description of the Hirsch lamp, which, though largely used in the United States of America, has not yet been adopted in Great Britain. The lamps, which consist of (1) the watchman's lamp and (2) the miner's lamp, are portable, and have been designed to provide a safe and reliable light for use by watchmen, and in mines, rescue-work, powder-works, oil-refineries, and other places where special precautions become necessary on account of the presence of explosive materials or gases. The lamps are in each in­stance operated by a storage-battery contained within a casing, and this supplies the current necessary for a miniature incandescent lamp. Each safety-lamp forms a complete unit and can be carried from place to place or held in any position. Appendices give details of battery cleaning, test results and safety reports

Dec 1, 1916

By T. Guyaguler

An analytical technique using computer-based multiple-regression methods was employed to determine the relation between the dust-producing index and inherent rock properties of typical samples from a coal-producing area, one of the aims being to provide a preliminary predictive tool for practical use. The investigation demonstrated that factors varied in their influence under different conditions, the brittleness:toughness ratio and the hardness being the most significant inherent properties with hardness showing the highest positive correlation coefficient

Jun 13, 1905

By N. Powell, R. J. Pine

An algorithm is proposed for updating the probability of slope failure on the basis of sequential testing using Bayesian probability theory. The approach is novel and computationally straightforward since, unlike other methods, updating of the probability of failure is carried out directly. This is because the probability is treated as a random variable whereas other methods have considered it as a purely deterministic value or as a function of shear strength parameters that are updated individually. The prior information required for the Bayesian analysis is obtained by a conventional probabilistic analysis. An exponential distribution is then used for the probability of failure, applying the principle of maximum entropy. This distribution is continually updated for individual slope cells, where repetitive excavation creates several such cells and a corresponding series of Bayesian estimates of the probability of failure is obtained. The approach is applicable to most simulations but there are limitations on its use. A more mathematically rigorous refinement using the beta distribution is currently under development

Apr 1, 1996

By W. R. Chambers

A wide variety of mining conditions exists within the South Midlands Area and across this range of conditions more than one half of the mines are highly susceptible to spontaneous combustion. Two thick seams in which the greatest risk exists are described and illustrated. The different heatings which take place are categorized by the locations at which they occur in the mines: additional special cases not easily categorized by location are discussed separately. The discussion for each category of heating follows the pattern of: (i) the reasons why it occurs; (ii) when it arises the means by which it is fought, and (iii) the preventive measures taken in an attempt to avoid its occurrence. Relatively new factors which may affect the incidence of heatings are highlighted and suggestions are made which may assist in reducing the number of incidents in the Area. A new method of continuous sampling, analysis and recording is described and mention made of an original method of interpreting carbon monoxide results with the aid of the computer. The first results from this work show that an early warning is given of an adverse change in trend several weeks earlier than with the present methods. Lastly, suggestions are made about the direction in which research might proceed to assist in reducing the special hazards created by several features inherent in the present methods of mining.

May 23, 1905

By G Williams

Discussing equipment, systems of work, the need for updated programmes of local seismic exploration, and developments within the South Wales coalfield.

Jan 1, 1993

By Haldane J. S.

Discussion of a paper presented at the Institution of Mining Engineers' general meeting held in London on 8th June 1916 included oral contributions by Louis H., Mowat D.M., Lupton A., Bailey T.H., Blackett W.C. and Gerrard J., and written contributions by Collis E.L., Carlow C. and Wilson W.B., with the author's oral and brief written responses

Dec 1, 1916

By W. J. Whiten, D. W. Grinsberg

Most cluster analysis techniques are not well suited to the analysis of engineering data as they have been designed for more qualitative data that tend to produce compact clusters. A clustering technique is described which develops and uses local cluster shapes to build clusters that are suitable for use in engineering applications. The technique is finding application in the analysis of many types of data, particularly where multiple trends and outlying points occur in multiple dimensions. Applications of particular interest are the calibration of on-stream analytical equipment and the analysis of data on plant performance. In both cases the multidimensional nature of the data renders manual analysis very difficult

Dec 1, 1991

By Winmill T. F.

Among the various theories proposed to account for the spontaneous ignjtion of coal, one which has at times been very strongly held is that the initial heating is due to the oxidation of iron pyrites. From the results described in this paper, it is possible to calculate roughly the rate of spontaneous heating of a specimen of finely-divided pyrites, on the assumption that all the heat developed is used in raising the temperature of the pyrites, and that none is lost. It is clear that where finely-divided pyrites occurs in considerable proportion among coal, it may be the chief factor in originating combustion, but that pyrites can only be the cause of a heating when it is present in considerable proportion, and in a very finely-divided state

Dec 1, 1916

By S a m u e l D e a n

The author's written response to previous discussion was presented at the North of England Institute of Mining and Mechanical Engineers general meeting held in Newcastle-upon-Tyne, 8 April 1916, followed by further comments by Hare S. in support of his view that the conditions in English mines were the reason for less satisfactory results being obtained with heading machines and brief comments by Greener T.Y., President

Dec 1, 1916

By G. J. Lyman

Mayer curves are used for process calculation in coal preparation. They can also be used to smooth washability data by fitting a hyperbola of particular properties to ash and yield, but to introduce the density variable an independent relationship with ash content must be adopted. When this ash-density relationship has a realistic form at low density, the implied form of the mass distribution function is unrealistic, suggesting that Mayer curves represented by a hyperbolic functional form are unsuited to coal washery calculations for low-density separations. Their use at higher densities is also uncertain. A similar conclusion can be anticipated when Mayer curves are used for other mineral systems.

Jan 8, 1992

By R. F. Bell, Schultz

The paper briefly discusses the nature of spontaneous heating in mines in the Doncaster area, in the period immediately before 1967 and steps taken to prevent and treat such outbreaks. The changes that led to the increased rates of advice of Barnsley Seam faces since 1967 are listed and the effects of these increased rates on the frequency and location of spontaneous combustion are discussed. The change in methods of control required by the increased rate of advance of the faces and the changes in location of outbreaks are described. Some typical heating situations are evaluated. The methods described include the use of air sealants, water gels for filling of voids in wastes, the balancing of pressures across heating areas by pressure chambers, booster fans, and the resiting of air separation doors, and the sealing of air-ways by flooding. The authors discuss the influence of mine layouts on the risks of spontaneous combustion and advocate that future plans should be designed to limit the number of districts at risk when heatings occur.

May 23, 1905

By G. R. Chaudhury

Many base metals, such as copper, lead and zinc, are commercially extracted by thermal processing of sulphide concentrates. However, owing to the depletion of high grade sulphide ore reserves and to environmental legislation, efforts have been in progress for some years to develop methods for the extraction of metals from lower-grade oxide ores and secondary resources, and there are now examples of commercial-scale operations.

Dec 1, 1995

By A. M. Marabini, S. Battaglia, M. Ciriachi

A computer program has been developed that produces graphic representations of the atomic structure of any crystallographic plane of a mineral. The information provided by the program relates to a purely geometrical model of the crystal structure in which each atom is represented solely by the x, y and z coordinates of its centre. Despite its simplicity, the program can be used as a first approximation model in studies of the interaction between mineral processing reagents and the surfaces of mineral grains which are assumed to be coincident with cleavage planes.

Jan 4, 1992

By C R. Ferrari

Residual subsidence is generally accepted as being about 5% of the total subsidence occurring within 12 months of all mining finishing. This paper looks at five case studies from different parts of the country, in various mining settings within a depth range of 430m to 760m. From a single seam single panel working to working the eleventh seam, all are within the concealed coalfield, similar to today's mining. The monitoring of subsidence continued for many years once the mining had finished and the results obtained are at considerable variance from the accepted norm. Subsidence has been found to carry on for up to eleven years after mining has ended, within a range of 8% to 45% of total subsidence. A highly significant factor was that subsidence, as a whole, was generally much more than predicted. The residual subsidence aspect has to he viewed in this context and in order to debate the subject at length, the causes of residual subsidence have to be balanced against the apparent inability to accurately predict subsidence. The results from the case studies were similar, even though the mining settings differed considerably. Subsidence of around 10% to 20% continued for several years after mining had ceased.

Jan 7, 1997