Search Documents

By Jennifer Ward

The primary objective of this paper is to establish how a low cost, high definition (HD) camera can allow for easy sustainable recordings of blasting operations. The subsequent analysis of each video can be utilized to monitor what type of performance was achieved and aids in improving blasting performance.

Jan 1, 2015

By F. Freme

For the second time in four years, the coal industry was brought to the forefront of the nation’s consciousness in 2006, as two separate events unfolded which involved coal miners trapped underground. Unfortunately, the tragic results of the 2006 incidents were not the same as in 2002 when the trapped miners were all successfully rescued. In January, two different incidents, both in West Virginia, focused the public’s attention on the dangers that miners face on a daily basis. As a result of these unfortunate events new legislation requiring improvement in safety in underground mines passed both at the federal and state level. In 2006, a total of 47 miners died on the job, matching the total number that occurred in 1995, and more than double the 22 killed in 2005. Notwithstanding those tragic events, coal production in the United States reached another record level in 2006, ending the year at 1.05 Gt (1,161.4 million st) according to preliminary data from the U.S. Energy Information Administration (Table 1). Production in 2006 was 27.1 Mt (29.9 million st) higher than the prior record set in 2005 of 1.03 Gt (1,131.5 million st). Although coal production rose in 2006, U.S. total coal consumption actually declined for the year. Coal consumption decreased in the electric power sector by 1.1 percent, while coking coal consumption decreased slightly. Only the other industrial sector had higher coal consumption in 2006, increasing by 0.3 percent. (Note: All percentage change calculations are done at the short tons level.) U.S. coal exports declined slightly in 2006, while coal imports again reached a record level. The excess production over consumption allowed total coal stocks to increase significantly during the year, as electric generators rebuilt their stockpiles that had fallen substantially in 2005 because of missed shipments in the second half of that year.

Jan 1, 2007

By D. Goossens

Quality control is a system which should guarantee that quality is achieved. It is the execution and verification of a project in an organised way, in order to obtain the maximum of certainty that the results meet the requirements. This concerns all stages of the project, from the soil investigation, over the design, to the execution. Quality control can and has been successfully realised for important projects by means of a quality plan. A quality plan is based on a number of general considerations, but should certainly be focussed on the particularities of a specific project. Practical examples of quality plans, which have been realised on sites in Belgium, are developed and the advantage of the system is shown by concrete case studies.

Jan 1, 1996

To many Australian Mining Engineers, we take it, the singular features of banket deposits are not as familiarly known as they would wish, possibly because in the majority of instances they are not in touch with the South African milling world, and have had little opportunity of studying the development of the banket beds, either from correspondence or literature. The writer hazards this opinion feelingly, because, when in Australia and before he had visited Africa, the utmost knowledge he was able to obtnin was a mass of conflicting theoretic discussion as to the agencies which formed the banket bed, without any practical hints as to their geological horizon, the rocks with which they are associated, the usual appearance and character of the ore, in fine, without that everyday detailed description which the miner requires when seeking information regarding mineral or metal deposit foreign in character to any that he has yet studied, or as yet had any opportunity of studying in his own country.The writer recognised that many more able men than he have from time to time discussed the features and formation of the banket beds of the land, notwithstanding which and feeling that many of his Australian colleagues have found themselves in a similar position regarding accurate detailed information respecting these African banket deposits as he himself was, he hopes that the present paper on the said deposits, as found on the fields under notice, will prove useful to some and of interest to all.

By Jeff Ardron

Unlike the first predicted deep-sea mining (DSM) boom 35 years, the public response to the re-emergent possibility of DSM is this time round is not entirely optimistic, with serious economic, social, and environmental concerns being voiced. In the intervening years, the troubling notion of the ‘resource curse’ has been popularized, whereby the economies of developing nations rich in natural resources (agriculture, minerals, and fuels), paradoxically appear to fare more poorly than their brethren who have fewer such resources. There have been a variety of explanations and counter-arguments regarding why the resource curse occurs, including how it can be ‘escaped’, and even some disagreement on whether it in fact does occur. Nevertheless, many commentators appear to agree that that the quality of governance is strongly implicated in the socioeconomic success, or failure, of these resource-dependent nations, and could indeed be the deciding factor. Unlike nations with diversified economies, the majority of the income from natural resource economies, in the form of royalties and rents, flows through national government; hence, good governance and fiscal management is of particular concern.

Sep 1, 2014

By Benjamin H. Clark

"For over 50 years, Derrick Corporation has been renowned for its innovative and durable fine screening equipment and screen surface technology. Derrick’s latest innovation, the patented Stack Sizer, offers mineral processors both high tonnage capacity and high separation efficiency on an extremely small footprint.The Stack Sizer is suitable for separations from 6.3 mm down to 75 microns (200 mesh). The Stack Sizer, coupled with Derrick’s patented urethane screen surface technology, offers an extremely economical alternative to hydraulic classifiers, hydrocyclones, and less efficient low volume wet screening systems. Stack Sizers have been used in feed preparation for flotation, spirals, and a variety of jigs. Mineral processors wishing to reduce grinding circuit circulating loads and generation of slimes due to over grinding, thereby enhancing the efficiency of flotation and gravity circuits, now have another technology at their disposal to perform this critical sizing and grade control function.Over 200 Stack Sizers have been installed in numerous mineral processing applications worldwide attesting to the rapid acceptance of this technology. Stack Sizers are currently screening ferrous and non-ferrous metal ores, mineral sands, silica sand, kaolin clay, feldspar, garnet, phosphate, aluminum dross, potash, coal, tantalum, spodumene, niobium, and other rare earth mineral ores.INTRODUCTIONDerrick engineers have long understood and demonstrated the importance of screen width in coupling both high capacity and high separation efficiency for fine wet sizing applications. As opposed to fine dry sizing, where the length of the screening machine is critical for high separation efficiency, introducing slurry feed to screens in a thin and even layer at minimal velocities across wider screen surfaces allows for high capacities and efficiencies, with maximum screen cloth life. This is due primarily to the combination of free liquid and high frequency vibration of the Derrick motors, which allow fine undersize material to pass through the screen apertures. Lacking either of these factors would be extremely detrimental to the screening process. Without the high frequency vibration of the motor, the screen is essentially a low efficiency sieve bend. Without the free liquid to carry fines through the screen openings, the screen is for all intents and purposes a glorified conveyor or dewatering unit, as little or no sizing takes place once the screen is devoid of free liquid. For optimal screening results, Derrick recommends feeding slurry to a screen at approximately 20% solids by volume. Figure 1 shows the Stack Sizer design concept. Note that a single feed point is used to evenly distribute the flow to the five separate feed points."

Jan 1, 2007

We report the studies of Proton-Exchange Membrane Fuel Cells (PEM FC) and hydrogen storage materials at McMaster University for the last 14 years. From the initial investigation of ionic conduction mechanism to the revelation of the origin of non-Arrhenius temperature dependence, as well as the synthesis and characterization of high temperature polymer electrolytes, both experimental and theoretical works have been compiled for the fuel cell membranes. In addition to the discovery of suppressed ionic conduction in Electrode-Membrane Assembly (EMA) and novel hydrocarbon PEMs based on micro-emulsion, the first evidence of hydrogen adsorption saturation by carbon nano-tubes was also achieved, which has been the bottleneck for the application of PEM FC. Prior to our study, a number of controversial publications have claimed the hydrogen capacity of these materials to be between 0.1 to 10.0 wt.%, and none demonstrated a plateau of adsorption with pressure that is consistent with monolayer saturation. Others suggested that the tube bundle structure is opened under high pressure to enable higher adsorption on newly uncovered surfaces, but received no confirmation. Using our home made high-pressure instrument with in-situ electrical probes, we found that a plateau is nearly achieved at about 300 atm in the room temperature isotherm, and that nanotube bundles actually compress with pressure instead of splitting, using in-situ electrical measurements.

Jan 1, 2005

Coal Preparation Research at Turkish Coal Enterprises (TKI)

Sep 13, 2010

By E. P. Deliac

The aim of this joint work between the French Coal Board and the Paris School of Mines is to be able to practically model the behaviour of a transverse drum cutting rock with picks. First a theoretical approach leads to the concept of cutting curves, giving forces and torque against penetration per drum revolution. Then experimental evidence, from full scale and reduced scale testing, validated and confirmed the theoretical shape of the curves. Finally practical applications are given, to improve the design or use of a shearer (or continuous miner). A micro-computer program is being developed to predict the cutting performances of a machine in certain conditions.

Jan 1, 1985

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in development of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-L Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

By K. Mallikarjuna Rao

There are several methods available to estimate deflection and ultimate Capacity of laterally loaded piles. In this investigation an attempt has been made to verify the existing methods for prediction of ultimate lateral resistance and deflection with the laboratory and field test results reported in the literature. A 75 pile loading test data obtained from the literature was used to evaluate two methods designed to predict the ultimate lateral resistance of rigid piles and three methods designed to predict the lateral deflections of rigid piles and four methods designed to predict the lateral deflection of flexible piles subjected to lateral loads. The accuracy and precision of each method is quantified statistically. The statistical results of the overall analysis indicate that the mean values of the ratios of predicted to measured lateral capacities vary from 0.62 to 1.14 with an average of 0.88. However, the settlement predictions were much more widely scattered than the ultimate load predictions and in general all the methods have a tendency to under predict the deflections. A new method is proposed by modifying the Broms's method to estimate the lateral deflections of free headed rigid and flexible piles separately. The proposed modified methods were found to be reasonably good in comparison to existing methods and to overestimate deflections.

Jan 1, 1996

By Forrest T. Moyer

To keep the mineral and allied industries informed of trend: in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and publishes, periodically health and safety statistics. This report includes data for 1961 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1963

By C. R. Carpenter

A dynamic gas-mixing system assembled by the Bureau of Mines for the generation of precise gas mixtures from sources of concentrated or pure gases and diluent gases is described. A set of electronic mass flow controllers with maximum flows ranging from 10 to 5,000 ml/min, a so-called Pure Air Generator, and gases in cylinders are used to generate differing gas concentrations. The repeatability of the delivery rate of a flow controller, measured on different days, has a precision of 0.3 pct of the setting. This dynamic gas-mixing system reduces the cylinder inventory and the demurrage charges for special gas mixtures. Gas mixtures that cannot be shipped commercially, such as flammable mixtures of methane in air, can be conveniently prepared by this system. The maximum dilution ratio is 2.5 x 104. Thus, gas mixtures can be made over a wide range of concentrations, from the percent region (by dilution of a pure single-component gas) to fractional parts per million (by dilution of a premixed standard, e.g., a 1,000-ppm mixture). This system is especially useful in determining the response of gas detection devices over the entire range of their measurement. Because the controllers are voltage controlled they lend themselves easily to automated control using computer-based systems.

Jan 1, 1983

By G. A. Bole

"This paper presents a review of the literature and is an epitome of work acne and articles published by Schurecht, Robson and Andrews', in the investigation of the feasibility of making basic refractories from dolomite, was carried on successively by these men, at the Ceramic experiment Station of the Bureau of Mines, Columbus, Ohio.Scope of the work.The dolomite refractories investigation of the Ceramic Station includes a study of the many fluxes which could be used to aid in the dead-burning of dolomite and also a complete survey of the iron oxide-alumina-silica field as fluxes. The temperature of calcination and the resulting properties have been carefully investigated, and the most desirable calcines chosen for further investigation in the making of dolamite bricks. Many binders and the several methods in common use of fabricating bricks commercially were tried, and a thorough study was made of the properties of the most successful ware,Previous Investigators.Even before the World War, considerable work was done on dolomite this war greatly accelerated the efforts of the many Investigators."

Jul 1, 1924

By P. H. Reynolds, S. Liaghat, A. Zarasvandi

"Darreh-Zerreshk and Ali-Abad are two relatively small porphyry copper-type deposits in Yazd Province in central Iran. They are located within the central Iranian volcano-plutonic belt, formed above the collisional convergent margin of the Iranian lithospheric plate from the late Eocene to the Miocene. This paper discusses the geochemical characteristics of the igneous rocks, and 40Ar/39Ar geochronology of plutons and alteration phases associated with the Darreh-Zerreshk and Ali-Abad deposits. The deposits are spatially associated with igneous complexes that consist of older and barren granites intruded by intermediate-composition granitoids, which are the carriers of Cu mineralization. The granites have relatively high content of Nb, Y, and K, a prominent negative Eu anomaly, and were probably derived from melting of, or contamination of mantle-derived magmas by, continental crust. Porphyritic diorites, quartz monzodiorites, and granodiorites show enrichment in light rare earth and large-ion lithophile elements, depletion in middle rare earth elements, and have no negative Eu anomaly. These intermediate-composition granitoids were derived from melting of the upper mantle or lower crust, and their differentiation was controlled partly by fractionation of hornblende. A pilot K/Ar whole-rock dating study suggests that the pre-ore granites were emplaced in the Oligocene. Dating by the 40Ar/39Ar method of nine samples of secondary biotite and sericitized rocks from drillcore within the mineralized and altered zones in both deposits yielded a well-defined age of ca. 16 Ma. This date is interpreted to be the time of hydrothermal alteration and of porphyry copper type mineralization in this part of Iran."

Jan 1, 2007

By Clarence Hall, Spencer P. Howell

Among the more important factors involved in the use of high explosives in blasting operations is the means employed to bring about the detonation of the charge. When flame is applied to high explosives many of them may burn if not confined; but all of them when burning under certain conditions of confinement may detonate. Detonation may also be effected by mechanical means, such as frictional impact caused by a blow or by rubbing between surfaces. By this means, however, the full effect of the explosive charge may not be developed, so that a partial detonation, often accompanied by the burning of the explosive, results. When nitroglycerin was first used it was fired by the application of flame, but considerable difficulty was experienced in exploding it with certainty and in obtaining uniform resl'llts. In 1864 Allred Noble, a Swedish engineer, discovered that nitroglycerin could be surely and completely detonated by exploding in contact with it a small quantity of an initiatory explosive. Mercury fulminate was the substance then found capable of producing the best results There are many other fulminates and other substances that will produce complete detonation of commercial" high" explosives, but detonators or electric detonators containing mercury fulminate as the characteristic ingredient are still almost exclusively used in this country. The term" detonator" is used in the publications of the Bureau of Mines to designate what the miner calls a "blasting cap "-a copper capsule containing a small quantity of some detonating compound that is ignited by a fuse. The term" electric detonator" is applied to a blasting cap that is similar except for being ignited by means of a small wire which is heated to incandescence or fused by the passage of an electric current. One of the conditions prescribed by the Bureau of Mines for a permissible explosive a is that it shall be :fired by a detonator, or preferably an electric detonator, having a charge equivalent to that of the standard detonator used at the Pittsburgh testing station. A further requirement is that this charge shall consist by weight of 90 parts of mercury fulminate and 10 parts of potassium chlorate (or their equivalents). At the request of a manufacturer of permissible explosives, an investigation was undertaken by the bureau to determine the relative strength of detonators and electric detonators having different compositions. The tests of electric detonators herein reported were conducted by H. F. Braddock, junior chemist; J. W. Koster, J. E. Tiffany, junior mining engineers; and A. S. Crossfield, junior explosives chemist, at the Pittsburgh testing station of the bureau. Similar tests of detonators were not conducted because it was believed that the results would not show sufficient variation to warrant such tests. It is hoped that the conclusions drawn from the tests made will be of service to those using explosives by enabling them to select the grade of detonator or electric detonator that will insure the most effective results. The conclusions are given in this bulletin, which is published by the Bureau of Mines as one of a series of publications dealing with the testing of explosives and the precautions that should be taken to increase safety and efficiency in the use of explosives in mining operations. The results of tho experiments described in this bulletin show that the average percentage of failures of explosives to detonate was increased more than 20 per cent when the lower grades of electric detonators were used instead of No. 6 electric detonators, and was increased more than 50 per cent when these lower grades were used instead of No. 8 electric detonators. It is noteworthy, however, that when sensitive explosives, such as 40 per cent strength ammonia dynamite (p. 33), were tested under conditions ideal for detonation, the same energy was developed irrespective of the electric detonator used. When tests were made with a less sensitive explosive, such as a 40 per cent strength ammonia dynamite containing nitrosubstitution compounds (p. 32), the energy developed increased with the grade of the electric detonator used. For example, the average efficiency of four different explosives was increased 10.4 per cent when a No.6 electric detonator was used instead of a No.4 electric detonator, and 14.9 per cent when aN 0.8 electric detonator was used (see tabulation onp.45). The results of the tests emphasize the importance of using explosives in a fresh condition, but as fresh explosives can not always be had in mining work, strong detonators should be used in order to offset any deterioration of explosives from age.

Jan 1, 1913

Geochemical data on Australian granites and pegmatites, and the mineral components of these rocks, are compared with that obtained in similar studies in the U.S.S.R. and elsewhere.The geochemical character of tin granites and the trace chemistry of their component minerals, particularly biotites, have some significance as ore guides in prospecting for tin.The primary geochemical dispersion of tin can be readily tested both in the laboratory and field by colourimetric methods, after volatilization with ammonium iodide, using modifications of the method described by Wood (1958).Secondary dispersions of tin in residual soils or alluvia can likewise be readly tested by rapid colourimetric methods in the field, but simple hydraulic methods, handling larger sample volumes, give reliable outlines of dispersion patterns.INTRODUCTIONThe search for tin ores, whether lode or placer in type, is usually directed on genetic grounds to country within or adjoining acid intrusives.A long established means of prospecting is to test samples for cassiterite by panning or other hydraulic separation.These methods can be used on crushed lode material or the natural materials from placers.With the advent of new techniques for extraction and for colourimetric analysis for tin (Wood, 1958 and Ross and White, 1961) a means is available for rapid analysis of materials not susceptible to quantitative testing by hydraulic methods because of the fine sizings of cassiterite or the occurrence of tin structurally held in minerals. The new methods thus opened up the field of tin prospecting by extending the search for ore guides to genetically associated rocks and minerals, wall ror-ks of veins and a wider range of superficial deposits.

Jan 1, 1963

The proper selection of a coal for a particular use depends on knowledge of fundamental data concerning the coals that offer, particularly their type and rank. Type of coal depends on the nature of the original plants and the environment in which they accumulated.Rank reflects the subsequent metamorphism of the coal, and is of two kinds-physical rank and chemical rank.INTRODUCTIONIn the different coalfields of the Commonwealth of Australia there occur many different kinds of coal which provide the coal-research worker with a wide range of material, but to the fuel technologist they represent complex problems in utilization.In the past it has been common practice to instal coal-using equipment of a design based on plant used in large industrial centres of other countries and then search for supplies of suitable coal. This has led to the transportation of coal mainly from New South Wales to other States, which have inadequate supplies of coal suitable for use in the equipment they have installed. However, modern economy and industrial practice demand local resources of coal for the development of industry, transport and domestic services, and a change in the old order is rapidly taking place. Technologists and engineers are now faced with the problem of designing and installing equipment to use whatever kind of coal is available in local coalfields.Much has been accomplished in this direction and important investigations are at present being carried out, but there still remains a wide field of problems for research.In planning and carrying out investigations into coal utilization it is essential that fundamental data and knowledge should be available and that its significance should be appreciated.

Jan 1, 1955

Jan 1, 1994

By P Vasconcelos, X D. Deng

Numerous supergene manganese oxide deposits are developed inSouth China as a result of weathering of a thick sequence of Paleozoic marine Mn-bearing sedimentary rocks, consisting mainly of limestones, cherts and black shales that were intensely folded and faulted due to multiple episodes of tectonism since the late Triassic. The ore minerals are dominantly pyrolusite, cryptomelane, nsutite, lithiophorite and braunite. The supergene manganese ores contain Mn ranging from 20 to 44 wt per cent; manganese oxide deposits derived from cherts and black shales also contain recoverable levels of Co, Ni, Cu, Pb and Zn. 40Ar/39Ar dating of potassium-bearing manganese oxides reveals that extensive supergene manganese ore formation started at least in the earliest Miocene and persisted to the Present. Ages of the deposits show a close correlation to tectonic stability, with the oldest in tectonically quiescent areas and the youngest in active areas that have subjected to continuous uplift and thus significant denudation. The prolonged wet and hot climate since Oligocene and the balance between weathering and erosion, which is parameter to the tectonic stability, are the ultimate controls on the formation and distribution of South China supergene manganese oxide deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008