Search Documents

By R. Le Houillier, M. Nagamori, A. J. Plumpton

"Asbestos tailings are a typical serpentine, hydrated magnesium silicate, consisting primarily of antigorite and a few per cent of unrecovered fibrous chrysotile. Serpentine has unique thermal properties in that dehydroxylating calcination at 600 to 700°C can yield an amorphous structure in which most of the magnesia is liberated from the original bond with silica and thereby rendered chemically active. The amount of activated magnesia can be quantified by selective leaching with a weak acid such as acetic acid. Many wet processes have been proposed to extract magnesium values from calcined or natural serpentine by means of various acids and their ammonium salts. However, the only commercial utilization of serpentine today is found in dry processes such as the production of fused magnesium phosphate fertilizer .The present paper reviews the physical chemistry of the dehydroxylation of serpentine and also various wet and dry processes in order to provide a general view regarding the chemical transformation of asbestos tailings.IntroductionAsbestos fibers occur as chrysotile, a serpentine polymorph. More than nine tenths of mined asbestos ores consist of massive non-fibrous serpentine, primarily the polymorph antigorite, which is discarded as tailings after fiber extraction. For many decades, Quebec has been a world leader in the production of asbestos fibers. As a result, colossal tonnages of serpentine have accumulated in the Eastern Townships'!'. Serpentine minerals are found in large deposit s throughout the world, and significant research efforts have been made, particularly in Japan and the USSR, mostly in attempts to extract magnesia or silica values therefrom.The chemical composition of serpentine (chrysotile and antigorite) may be ideally expressed as Mg3Si2Os(OH). which corresponds to 43.7% MgO and 43.3% SiO2. Natural serpentines often contain a few per cent of Ni-bearing magnetite and other impurities, and therefore the contents of MgO and Si02are both about 40% or lower.Serpentine (hydrated magnesium silicate) is virtually insoluble in weak acids. However, when dehydroxylated under controlled conditions, ' it decomposes to an amorphous state in which magnesia and silica are isolated and chemically active. The magnesia so activated is readily soluble in weak acids. This unique characteristic of calcined serpentine, first discovered in 1942,, has since attracted the attention of innumerable researchers, whence many processes have been proposed."

Jan 1, 1980

By R. C. Tait

The gold at Giant Yellowknife is intimately associated with a complex mixture of sulphides, including pyrite, arsenopyrite, stibnite, and a wide variety of antimony sulpho-salts. Direct cyanidation has never been feasible. Recovery is almost entirely dependent upon flotation, roasting of flotation concentrate, and cyanidation of calcine. In November 1958, an Edwards-type roaster and an early prototype, two stage Fluosolids roaster, were replaced by a large two-stage Fluosolids roaster of improved design. The new roaster was started at "safe" medium temperatures, but early in 1959, temperatures in both stages were gradually and deliberately lowered to determine whether continuous autogenous roasting could be maintained under exacting low temperature conditions necessary for good extraction. Operation is smooth and continuous with first and second stage temperatures controlled at 925° and 875°F respectively. Plant cyanide ex-traction compares very favourably with extraction from low

Jan 1, 1961

By H. Powell

"This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, on-line technologies through review of published information available for on-conveyor minerals applications. Case studies include an iron ore and copper-gold company, both of which consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.INTRODUCTION Process operators rely on supply of a reasonable ore quality and consistency from the mine. Unfortunately neither the mining nor process operators have much control over the ore quality once it has been put into the crusher. Grade control typically stops once the material is designated as ore and the process plant operator needs to process it irrespective of quality. Plant control is most effective when technologies measure process streams directly and preferably in real time. Measuring sampling streams that are not representative of the primary flow will result in incorrect plant control decisions. Sampling coarse conveyed flows is expensive and impractical at many operations, however, this does not mean those flows cannot be measured. Investigations to find techniques suitable for real time elemental analysis have focussed on the application of known laboratory techniques to process streams. For conveyed applications, development of neutron irradiation techniques were most promising and early studies indicated potential success for bauxite measurement (Beurton et al, 1995). Tran & Evans (2001) concluded there was no equivalent technology to PGNAA in terms of material penetration power and that the technology was eminently suitable for basic industries such as cement. Nelson and Riddle (2003) evaluated PGNAA for possible use in the phosphate industry by using a unit installed in a cement plant to test performance on phosphate samples and ultimately recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control"

Jan 1, 2014

By Lutz Markworth, Evren Ören

"The worldwide demand of ores and the depletion of the high-purity deposits make it necessary to recover ores in increasingly finer size fractions in the feed material. The flotation technology of more than 40 years old plants was not able to recover the ultra fine material. Those slurry tailings ponds now have the chance to be re-processed with PNEUFLOT® technology.The bubble sizes of different flotation technologies have a huge influence of the results especially regarding the recovery of the ultra fine particle sizes.PNEUFLOT® technology of HUMBOLDT WEDAG Coal & Minerals Technology GmbH in Germany was applied to ultra fine Phosphate, Copper and Platinum ores. The results will be presented in this paper.Conventional technology like agitator flotation has its limits in the flotation of fines due to turbulences in the cell. The position of the agitator influences the recovery of the fines. A deep impeller generates a higher froth zone. This helps to catch the medium fines. Due to the static head of the slurry inside the cell, compressed air is required for such cell designs.Column flotation is well known for a good selectivity without having in the first cell a good recovery. This leads to invest in several cleaning stages to reach an acceptable recovery. Further more, compressed air is required to generate the air bubbles to the flotation process, which are much bigger than with PNEUFLOT® technology applied.INTRODUCTIONHigh metal prices are actually the basis to invest in poor deposits or deposits with very fine intergrown ores which have to be milled down to ultra fine powders less than 60 micron. The liberation grade has to be determined by a mineralogical analysis. Polish sections have to be prepared and interpreted by using of a microscope. Figure 1 and figure 2 are showing polish sections of a platinum-nickel ore from Petchenga Nickel at Zapolyarni Mine in Russia. The head grades for rich ore are for copper between 0.05 – 0.15%, for nickel between 3 – 7% and for platinum group minerals approx. 0.15 oz/t. With an efficient flotation technology it can be upgraded to 20 oz/t."

Jan 1, 2009

By Stephanie Price

Engineering Associations ?Regulatory authority ?License individuals and firms ?Discipline licensed members ?Enforce against improper acts ?Programs for EIT?s, competence, etc

Oct 1, 2010

By Ben R. Bjorkman

The future is here ? or at least that?s what Mine Planners predicted some 15 years ago ? that by 2004 we would have man-less mines running themselves using space-aged technology. Truthfully, though, there hasn?t been much change in mining methods in the past decade, but thankfully that?s all about to change. The benefits of autonomous ? even Tele-operated mining (especially in narrow-vein ore bodies) are wellknown: increased production hours by eliminating travel time to and from the face, continuous production at the face while crews screen and bolt behind the working equipment, less liability for workers? safety in certain areas, etc. But when plans are put in place to accomplish this vision, things stagnate and production carries on as before. This paper examines the components necessary to make that vision a reality. First we?ll detail the technology required to enable Tele-operation ? even autonomous operation of mining machinery, then we?ll look at what?s wrong with the current way we?re mining, and finally conclude with a critique of the machinery itself.

Oct 1, 2004

By G. K. Lee, E. R. Mitchell

Designers of combustion processes may select aerodynamic conditions which produce only superfine fly ash. Although it is not usually anticipated that this will create a problem, such as has been found to agglomerate in high-velocity gas streams, to plug mechanical dust separators in a short time, and to contribute to atmospheric pollution. The problem is a fundamental one, and may be approached in several ways. The authors, in the course of their combustion research program, had occasion to examine the agglomeration of ash, ranging from sub-micron to 17 microns in size, produced in a (coal and oil) dual-fuel-fired steam generator. Several theories, supported by extensive laboratory studies, have provided some understanding of a probable mechanism of agglomeration. As a result, certain precautions are suggested in the design and selection of combustion processes and equipment.

Jan 1, 1962

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

In this study, the dissolution behavior of copper and arsenic from five different copper concentrates containing 21-34.7 %wt. of Cu, 1.3-7.3 %wt. of As and 15.6-27.5 %wt. of Fe were investigated under high pressure oxidative leaching conditions. Leaching experiments were conducted using different leaching reagents such as ferric sulfate, sodium chloride, deionized water, sulfuric acid and ferric sulfate-sodium chloride mixture in order to compare the effectiveness of each on the dissolution of copper and arsenic from copper concentrates. The effects of ferric sulfate (0.1-1 mol/L), sodium chloride (0.1-0.5 mol/L) and leaching temperature (100-180C) were investigated under 1 MPa autoclave pressure , particle size >45 m, pulp density of 100 g/L, stirring speed of 750 rpm and leaching time of 60 min. Results showed that the most effective leaching reagents for the dissolution of copper are 0.34 M NaCl and a mixture of 0.1 M Fe2(SO4)3 - 0.34 M NaCl, in which As extraction did not exceed 7%. The copper concentration in the pregnant leach solution obtained after leaching using 0.1 M Fe2(SO4)3 - 0.34 M NaCl was 13-30 g/L, while the concentration of As and Fe were in a range between 0.3-1 g/L and 0.2-10 g/L at 160C. INTRODUCTION Copper sulfide minerals, such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and covellite (CuS) are used for the production of copper in mining and metallurgical industries worldwide. The conventional pyrometallurgical processing followed by electrorefining is a common process for the production of high purity copper (Moskalyk, & Alfantazi, 2003; Padilla, Aracena, & Ruiz, 2012). However, the degradation of copper content and an increase in the amount of metal impurities, especially arsenic (As), antimony (Sb) and bismuth (Bi) in copper concentrates cause serious problems to the production of copper and environmental pollution (Basha, Selvi, Ramasamy, & Chellammal, 2008; Long, Peng, & Bradshaw, 2012). Hydrometallurgical processes are used to recover metals from refractory ores, concentrates and tailings by leaching (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018). During the last decades, hydrometallurgical processing for the recovery of copper from enargite-bearing copper ores and concentrates has been extensively investigated due to its relatively more environmentally benign and less capital costs than the conventional pyrometallurgical processes (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018; Choubey, Lee, Kim, & Kim 2018). However, several issues facing the hydrometallurgical processing are incomplete extraction of copper associated with the coprecipitation of iron compounds, difficult stabilization of toxic impurities and production of a contaminated copper product (Dreisinger, 2003; Safarzadeh, Moats, & Miller, 2014). Hence, a number of studies have been conducted on the selective dissolution of copper from copper ores and concentrates or selective removal of arsenic leaving a clean copper residue using various leaching reagents or lixiviants (Safarzadeh, Moats, & Miller, 2014; Mihajlovic, Strbac, Zivkovic, Kovacevic, & Stehernic, 2007; Tongamp, Takasaki, & Shibayama, 2009). More extensive studies on the selective extraction of copper from enargite- bearing copper ores and concentrates are much needed to improve copper recovery.

Jan 1, 2019

By M. Leroux, P. Lacombe, S. R. Rao, J. Y. Kim, J. A. Finch, G. Labonté, N. Macminn, M. Ounpuu

"Laboratory investigations on two complex ores, the A1 zone ore from Les Mines Selbaie and the Lyon Lake ore from Mattabi Mines Ltd. (Division of Noranda Minerals), have been carried out to determine some of the main variables in collectorless flotation. In particular, the effect of pulp potential (controlled by gas composition), conditioning time, pH and grinding media have been studied.Chalcopyrite showed the greatest response to collectorless flotation among the four major sulphide minerals present, followed by galena. Flotation of sphalerite was variable from minimal to important depending on the mineralogy and the pre-treatment performed. Appreciable silver recovery was achieved collectorlessly for the Lyon Lake ore while it could not be achieved for the A1 zone ore of Les Mines Selbaie. It appears that the difference between the two ores is related to silver's predominance as tetrahydrite in the Lyon Lake ore while it is as argentite and native silver in the A1 zone ore.The response of the ores to collectorless flotation is strongly dependent on the pulp potential, Ep, and pH. Using different gas compositions and different conditioning times it was found that collectorless flotation occurs when Ep is +195 to +295 mv (vs SHE). The actual on-set potential for collectorless flotation is dependent on the ore. A too high potential or prolonged oxidation leads to a decrease in selectivity. Some other factors were examined, notably the effect of pH and the type of grinding media on the selectivity achieved in the laboratory.Preliminary results from a plant trial at Mattabi Mines Ltd. confirmed that collectorless flotation occurs and that it is preferential for chalcopyrite and to a lesser extent galena. Collectorless flotation was not attempted at Les Mines Selbaie. However, examination of the distribution of collector between the different addition points in the copper circuit suggests that it may be present."

Jan 1, 1990

Operations and maintenance departments have had a long-standing adversarial relationship. The widespread evolution and adoption of modern management techniques, such as reliability centered maintenance (RCM) and Lean, however, has driven interest in working co-operatively to optimize overall plant performance. Mining and minerals operations have long adopted RCM in maintenance and are now adopting Lean throughout organizations. Such modern management initiatives explicitly call for co-operation between the two disciplines of maintenance and production and many advances have been made in terms of people and methodology. One area that has lagged behind in supporting these developments, however, is information systems. Enterprise asset management (EAM) systems in maintenance and newer manufacturing execution systems (MES) in operations have not been truly integrated in the needed ways. Complicated plants, different software architectures, continually changing conditions and many other variables have led to systems problems, which have contributed to the maintenance/operations divide. Master data synchronization (the plant tree) and integrated reporting of real-time data with transactional data are just two of the issues that are being solved by new approaches in information technology, including web services and service orientated architectures. New technologies are coming on-stream to enable the final bridging of the gap.

Jan 1, 2009

By J. Molgaard, J. Masounave, J. Prinsen, P. Beaulieu, G. Huard

"A study carried out on behalf of the National Research Council (NRC) indicates that economic losses due to wear in the Canadian mining industry are in excess of $700 million annually. Severe wear, mainly by abrasion, was identified as the most important wear mechanism in terms of possible savings. One way to reduce losses would be the proper use of databases. A joint project of The Canadian Institute of Mining and Metallurgy (CIM) and NRC (Tribology laboratories at IMRI) has been initiated to create a factual database containing all relevant experience in the area of wear in the Canadian mining industry. As a first step, a prototype covering slurry pumps is being built. This should help to answer many questions, such as the number of people involved, interest from industry, cost vs benefits, etc.IntroductionTribology is concerned with the understanding of the mechanisms of friction, wear, and lubrication.Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of those surfaces with lubricants, with the chemistry, physics and use of lubricants and their additives. It is concerned with the reduction of friction and wear (or, in the case of belts, brakes, clutch plates, and similar devices, in achieving optimum friction with minimum wear) and is concerned with the avoidance of associated failures in machinery.Lubrication is usually the solution to a problem of friction and wear. Yet far from all the problems of friction and wear are solved by lubrication. The wear of grinding rods or shovel track pads can hardly be solved by lubrication, to name just two examples with which mining engineers will be familiar. There are indeed many situations of wear and friction where the surfaces in contact are unlubricated.In part, tribology is a matter of design. A major aspect, however, has to do with the choice of materials, to satisfy external constraints upon the component design or choice. The operating conditions for much industrial equipment, particularly in mining are, often very severe. The development of wear resistant materials, including materials which are applied as coatings, is clearly an important technology from the point of view of tribology."

Jan 1, 1987

By M. Leroux, S. R. Rao, J. A. Finch

"Poor Pb-Zn selectivity during Pb flotation in laboratory tests on a Mississippi Valley-type Pb-Zn ore was traced to apH effect. In the pH range, 9.5 to 11.0 sphalerite floated readily without copper activation. Compared to sphalerite flotation with copper activation this procedure gave equivalent selectivity but reduced flotation rate.Possible mechanisms of this sphalerite flotation without copper activation are discussed. Activation by Fe(OH)2 is suggested, the Fe- + ions being derived from superficial oxidation of pyrite in the ore. IntroductionGalena and sphalerite commonly occur together. A typical procedure, using xanthate collectors, is to float the galena first, at pH - 8, followed by flotation of sphalerite after activation with copper (II) sulphate at pH - 10 (to depress pyrite).Flotation tests following this procedure in an undergraduate laboratory course with a Pb-Zn ore from Polaris failed to achieve consistent selective flotation of galena. Occasionally a considerable amount of sphalerite, even though unactivated with CUSO4, floated. This was traced to accidentally high pH. A systematic study was carried out which revealed that sphalerite floated readily in the pH range 9.5 to 11.0 without activation by CuSO4 This paper describes the results of the study and discusses a possible mechanism of this flotation of sphalerite."

Jan 1, 1987

By D. E. Pickett, J. A. Roland Faucher

"INTRODUCTIONMineral processing is undergoing growth and change at a rapid rate. The modern flotation process was discovered only in the mid-twenties, and uranium leaching in the mid-fifties. The growth of individual unit equipment size is also a recent development and is perhaps most dramatically illustrated by the increase in size and connected horsepower in grinding mills. It is also apparent in much of the equipment used in mining operations.These technical and mechanical developments have influenced the design of plants but not to the expected degree.Many metallurgists believed until recently that grinding an ore in the absence of steel results in a loEs of selectivity in the flotation. However results reported by Thornton (1), Fahlstrom (2), Canmet (3 & 4) have shown on the contrary better selectivity and improved recovery at a lower operating cost. According to the Aitik (2) plant results, the net difference in cost plus tailing value in favour of the two-stage autogeneous grinding circuit is in the order of 40 cents per ton of ore milled. Even a greater difference was indicated by the results obtained by Canmet on a sample supplied by Mattagami Lake Mines Ltd.Yet how many plants are taking advantage of these findings and how many plants are being converted. How much more improvement of the results would have been obtained if these tests had incorporated optimization of classification efficiency? By nature the mining industry and the mineral processors are conservative, and tend to emphasize the possible penalties for an unsuccessful innovation out of proportion to the potential rewards even for a significant improvement."

Jan 1, 1979

By A. Sheikh, S. Hardcastle

"Various methods of leaching are being used by Denison Mines Ltd. Uranium Operations. This study was designed to investigate the flood leaching operation of two parallel inter-connected stopes contained by pressure bulkheads. The teaching muck piles, created from large scale uppers production blasts, are aerated by compressed air lines laid beneath the pile prior to blasting.A SFr, tracer gas, injection technique has been employed to determine the post-blast integrity of the single-ended air distribution system. SF6 was injected into the compressed air line feed to the stopes and collected at borehole exhausts from the stopes in grab-sampling bags. Analyses of the air samples were performed with a gas chromatograph.The system was designed to give a sufficiency of oxygen to sustain bacterial activities used to enhance the leaching recovery in the muck piles. The results obtained indicated that there is a minor anomaly in the distribution system that may not be critical to the operation. Compared to an idealized case, the over-all efficiency of aeration throughout the muck is estimated at over 85%."

Jan 1, 1988

By P. Brad Marchant

"To properly evaluate bioleaching as a commercial alternative for sulphide concentrate oxidation, to enhance cyanidation response, it was necessary to define and optimize critical operating variables outside of the laboratory under less than ideal conditions. A complete bioleach testing laboratory was installed at Equity Silver Mines to aid in pilot plant flowsheet development.A continuous pilot scale bioleach circuit was constructed to provide data for meaningful valuation of biotechnology on a plant scale. The important operating and design parameters for pilot plant testing are described. Plant scale feasibility and design considerations, to treat a refractory pyrite/arsenopyrite concentrate produced from flotation tailing, are discussed. 1.0 BACKGROUNDEquity Silver Mines Limited is located 37 km southeast of Houston in central British Columbia. A 70% owned subsidiary of Placer Development Limited, Equity is Canada's largest open pit silver producer. Ore reserves were estimated at 28 million tonnes grading 106 g Ag/t, 0.96 g Au/t, and 0.38% Cu from two pits, the Southern Tail and the Main Zone. Detailed geology and mineralogy has been described previously(1,2).The concentrator flowsheet consists of conventional crushing, grinding, flotation, and dewatering circuits processing 5 300 tonnes per day of new mill feed. The resultant Cu/Ag/Au concentrate is trucked to Prince Rupert for shipment to market. Mill tailing reports to a closed circuit pond from which mill process water is recycled. Details of the concentrator process have been reported( 2,3).Production in the Southern Tail pit, from July 1980 to March 1984, resulted in mill tailing averaging 0.9 g Au/t and slightly more than 20 g Ag/t. Historic data indicate that unrecovered gold is associated with arsenopyrite and silver losses with unliberated tetrahedrite or minor silve,, bearing sulphosalts. Main Zone mill tailing, which commenced production in March 1984, contains approximately 0.5 g Au/t which is probably associated by majority with silver bearing minerals and pyrite while silver losses, 30-40 g Ag/t, are associated with unliberated silver and antimony bearing minerals."

Jan 1, 1985

By K. B. Hodgins, P. Ouellette

"The North American mining industry faces challenging emissions regulations in the coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable.Westport Innovations Inc., Vancouver,British Columbia, has developed high-pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications while reducing emissions of nitrous oxides (NOx), particulate matter (PM), and CO2 with no loss in performance. This is accomplished through late-cycle, high-pressure direct injection of natural gas into a diesel engine combustion chamber at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the natural gas fuel main injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, lowspeed torque, high-power output, no engine knock, and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to the reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored with less impact on weight and space than compressed natural gas (CNG) by virtue of its increased energy density over CNG.Westport has applied HPDI technology to the Cummins QSK series engines for high horsepower applications such as power generation and mine haul trucking. HPDI can also be applied to other engine manufacturer platforms and market applications. Westport is interested in demonstrating the unique characteristics of HPDI in mine haul trucks to show diesel performance with low emissions levels using low-cost LNG fuel.Retrofitting a Tier 1 engine with HPDI would provide emissions reductions below the EPA 2006 Tier 2 standards while maintaining the performance and efficiency of the Tier 1 platform. The longer-term target is the Blue Sky voluntary standards of 3.8 g/kW-hr (2.8 g/bhphr) of NOx + non-methane hydrocarbons (NMHC), and 0.12 g/kW-hr (0.09 g/bhp-hr) of particulate matter (PM) and future standards. Typically, an HPDI engine is capable of reducing NOx emissions by 40% over diesel operation at the same efficiency. On a mining truck meeting Tier 2 standards, this NOx reduction would translate into NOx emissions approximately 14 t per year lower than under diesel operation. PM emissions are typically reduced by some 60% with HPDI fueling, which would translate into a yearly reduction of 650 kg. Similarly, engine-out greenhouse gas (GHG) emissions are reduced by 21%, resulting in a yearly reduction of approximately 950 t per vehicle.Above those of emissions reduction, efficient natural gas usage in mine haul operations would offer significant benefits in terms of fuel cost savings, which may be further combined with monetary emission credits. HPDI technology would enable operators to exercise environmental stewardship while gaining a competitive advantage in advance of new Tier 2 and Tier 3 emissions regulations. The advantages of natural gas use among mine haul truck operations can be replicated across a broad range of engines and applications."

Jan 1, 2005

By Lewis Martin

Whereas many researchers and mine engineers have conducted tests using different types of grout, grout ratios, and physical modifications of the cable to determine cable bolt load characteristics, few studies have been conducted on cables fitted with internal instruments. Those studies that have been done have concentrated on cable behavior averaged over significant cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed . This paper documents test results on these modified cable bolts. Three tests were conducted at SRL on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over significant cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable and thereby allow interpolation of maximum possible loads on a cable.

May 1, 2002

By Simon W. Houlding

The mining community is geographically remote and widely dispersed. There is a growing requirement for formalized professional development of members by professional associations, and increasing recognition of the advantages of continuing education and training by both individuals and corporations. Working against these trends are the increasing expense and time commitments required for attendance at conventional courses and workshops. The result is a perceived need for a readily accessible source of continuing education and technical reference on the Internet. The design constraints for an Internet model for professional development include: ? browser compatibility, with any time, any place, any pace accessibility; ? a content presentation model with low bandwidth requirements, appropriate interactivity for examples, tools and reviews, and viewer performance monitoring capabilities; ? formal accreditation of content, presentation and process so that viewer achievements may be formalized in terms of widely recognized Continuing Education Units; ? availability of tools for conversion of source material to the presentation format with minimal effort. A model that meets the design constraints is presented and illustrated by examples from an existing Internet site for continuing education in mining.

May 1, 2002

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton

"Hydrophobic polystyrene nanoparticle suspensions were evaluated as potential flotation collectors for pentlandite. Experiments involving both clean model mineral suspensions and complex ultramafic nickel ores confirmed that conventional water-soluble molecular flotation collectors such as xanthate could be partially or completely replaced by hydrophobic nanoparticle flotation collectors. The ability of nanoparticles to induce flotation was demonstrated by floating hydrophilic, negatively charged glass beads with cationic polystyrene nanoparticle collectors. Electrostatic attraction promoted the spontaneous deposition of the nanoparticles on the glass surfaces raising the effective contact angle sufficiently high to promote the adhesion of beads to air bubbles. As little as 10% coverage of the bead surfaces with our most effective nanoparticles could promote high flotation efficiencies, whereas conventional small molecular flotation collector requires ~ 20% or higher coverage for a good recovery. Surface functionalized nanoparticles enhanced the ability for nanoparticle collectors to selectively deposit onto surfaces of the desired mineral particles in the presence of gangue. For example, poly (styrene-co-vinylimidazole) nanoparticles were designed to selectively deposit onto nickel mineral (pentlandite) in the presence of Mg/Si slime. Flotation tests of ultramafic nickel ores at Vale with these nanoparticle collectors have shown improvements in both pentlandite recovery and selectivity. On-going work includes attempts to identify specific applications where nanoparticle flotation collectors might be cost effective.INTRODUCTION Most mineral processing operations include multiple stages of froth flotation to concentrate and isolate the desired product. Before flotation, chemical collectors are routinely added to ground ore slurries, selectively binding to mineral-rich particles, increasing their hydrophobicity thus promoting selective flotation. (Fuerstenau, Jameson, & Yoon, 2007) Conventional collectors are surfactants with a short hydrocarbon tail and a head group, such as xanthate. A typical conventional collector is potassium amyl xanthate (PAX), which is a small molecule with an extended molecular length of about 1 nm. Critical characteristics of a good collector include the ability to selectively adsorb onto desired mineral surfaces and to lower the water/mineral surface energy. Despite the extensive role of flotation in mineral processing, some ores are difficult to process by flotation. For example, ultramafic nickel sulfide ore containing both valuable pentlandite and large quantities of unwanted Mg/Si slime [primarily serpentine, (MgFe)3Si2O5(OH)4] responds poorly to flotation. (Mani, Xu, Quinn, & Stratton-Crawley, 1997) Fibrous hydrophilic Mg/Si slime usually masks the surface of pentlandite (known as “slime coating”) due to electrostatic interaction (Edwards, Kipkie, & Agar, 1980) and dramatically depresses pentlandite flotation. Consequently, new approaches are required for processing these difficult ores."

Jan 1, 2012

By K. L. C. Gonçalves, V. K. Alves

"CVRD’s Department of Development and Technology – GETEK has been developing and perfecting a general methodology for scaling up flotation and grinding circuits over several years. This methodology has been applied in several prospective CVRD mining projects. It encompasses a procedure for variability analysis based on bench scale tests, pilot scale grinding and flotation tests and modeling and simulation for scaling up the industrial flowsheet.The bench scale tests include the determination of the Work Index, simplified DWT tests, rougher flotation and locked-cycle tests with samples that are representative of the ore body variability. After completion of these studies, continuous, pilot-scale flotation tests are carried out at a Mini Pilot Plant with drill core samples representative of different stages of the mine life. Finally, studies are carried out with large volume samples using a conventional grinding and flotation pilot plant. This sample is also used for liberation characterization, grinding kinetics, flotation kinetics and industrial circuit scale up. This methodology has been successfully employed in the development of CVRD’s new mining projectINTRODUCTIONCVRD has been developing and perfecting a general methodology for scaling up flotation and grinding circuits over several years. The definition of the processing route and the sizing and scale up of the processing system are some of the products generated during the pre-feasibility of a greenfield project. This paper is focused on the scale up of grinding and flotation circuits, operations known to be of the most importance in a mineral processing plant.The methodology for the definition of the flotation and grinding circuits is divided in the following stages: bench scale ore variability studies, pilot plant operation and modeling followed by simulation. The product of this work is a calibrated simulator that can be utilized for plant operation as well as mine planning, looking to achieve optimal operational conditions.The current models used for scale up of the grinding circuits are aimed at the generating information about the size distribution of the circuit product. However, it is well known that the liberation state of these products may be of critical importance for the performance of the concentration processes downstream. Nevertheless, CVRD has been developing a methodology for liberation kinetics during grinding, aimed at optimizing grinding circuit throughput together with downstream flotation recovery."

Jan 1, 2006