Search Documents

By Forrest T. Moyer

The safety record of the coal-mining industry in 1968 worsened appreciably .in fatality experience but was slightly better in nonfatal-injury experience. Work fatalities in 1968 totaled 311 and occurred at a frequency rate of 1.33 per million man-hours or worktime. The fatality total was 89 higher, and the rate of occurrence was 45 percent higher than the corresponding figures of 222 fatal injuries with a frequency rate of 0.92 in 1967. The worsened fatality record in 1968 resulted primarily from two major disasters (a single accident which results in the death of five men or more) which killed 87 men, nine in one and 78 in the second. The total of 9,639 nonfatal injuries was the lowest annual figure in complete records back to 1930. The frequency rate of 41.12 nonfatal injuries per million man-hours of worktime for 1968 was the second lowest annual rate of occurrence. The severity rate of all injuries, 10,513 days lost or charged per million man-hours, and the average severity, 248 days lost per injury, in 1968 were the worst annual data in the series started in 1944. Total worktime of 234.4 million man-hours and coal output of 553.3 million tons in 1968 were, respectively, 3 and 1 per- cent lower than in 1967.

Jan 1, 1972

By Dongok Kim

Regardless of the advantages of the Friction Stir Process (FSP), for age-hardened aluminum alloys, the mechanical properties such as hardness in the stir zone decreased after FSP due to the growth or dissolution of strengthening precipitates. Here, as a new technique, FSP was introduced to alloy copper nanopowders in Al7075 T651. Mechanical properties of copper nanopowder- alloyed Al7075 T651 together with micro and nanostructures were compared with those of as-FSPed Al7075 T651 using SEM, TEM, and Vickers hardness testing to understand structure-property relationships. It was observed that Vickers hardness of the stir zone in copper nanopowder alloyed Al7075 T651 increased by 20% compared to that of the heat affected zone, while the as-FSPed samples did not show a noticeable increase in hardness in the same zone. Xray mapping showed traces of copper nanopowder after the process. TEM is being used to verify if there was CuAl2 formed in the copper alloyed sample.

Jan 1, 2006

By A. R. Kiani-Rashid

Controlled graphitization has become known as a practical method for improvement of wear resistance and machining properties in steels. In this paper, the effect of heat treatment on microstructure of CK45 steel has been investigated. Austenitising was carried out at 920°C for 5 hours. Besides, isothermal transformation was conducted at 750°C in the time range of 1-20 hours. The microstructure of the steel considerably changes by this heat treatment process which exhibits the effects of temperature, appropriate austenitising duration and isothermal transformation. Conducted experiments show a suitable distribution of semi-spherical graphite particles especially on the surface of the steel. Also, analyses demonstrate that the amount of formed graphite in the austenitising temperature 920°C is more than graphite in single heat treatment temperature of 750°C.

Jan 1, 2010

By H. J. Heinen

This Bureau of Mines report reviews the recent developments in the heap leaching of gold ores with dilute cyanide solutions and the recovery of gold and associated silver from the pregnant effluents by a carbon adsorption-desorption method. Mineralogical considerations, experimental work, field studies, and commercial operations are described. Also presented are recent process advances developed by the Bureau, including the application of (1) alcohol additives to the conventional hot alkaline cyanide strip solution to enhance gold desorption from precious metal-laden activated carbon, and (2) Na2S precipitation of the silver from geld-silver cyanide solutions as a means of reducing the inventory of carbon required for precious-metal adsorption from heap leach effluents and for the production of low-silver bullion from activated carbon stripping solutions.

Jan 1, 1978

By Yukihiro Ishihara, Nanase Ogawa, Ming Lei

"Abstract In the Press-in Method, a static jacking force is used to install a prefabricated pile, while a reaction force is gained from previously installed piles. This piling technique has solved problems in urban piling construction such as noise and vibration associated with the piling work, restricted construction conditions due to the existing structures, and so on, since its emergence in 1975. Its applicability to hard ground conditions has been improved, with the development of press-in machines that involve augering or rotation. Besides, information such as time, penetration depth, jacking force and rotational (or augering) torque in piling work are automatically obtained. The concept of PPT, Pile Penetration Test, has been developed by the authors, to apply the obtained information to the processes of construction planning or foundation design. This paper highlights the technique to estimate SPT N value from data acquired in standard press-in (press-in without any auxiliary methods), press-in with augering and rotary press-in. The technique will be helpful in assuring the adequate embedment depth, re-selecting the adequate press-in machine or auxiliary method, and re-pricing the project objectively, particularly when a contractor encounters unexpected ground conditions.INTRODUCTIONThe Press-in Method is one of the piling techniques that use a static jacking load to install piles. It mitigates environmental problems of noise and vibration that have been associated with other conventional piling techniques.It is also featured by its spatial efficiency; since a ‘press-in’ piling machine gains a reaction force from the previously installed piles, there is no need of bulky weights that will occupy a large space. This feature is emphasized in the piling system in Figure 1, where a press-in machine and its related devices are all positioned and ‘walk’ on top of the pile wall.Its applicability to hard grounds has significantly been improved, with some newly developed piling machines that involve augering or that install tubular piles with teeth on the base by applying axial load and rotational torque at the same time."

Jan 1, 2014

As part of the Bureau of Mines program for conserving domestic mineral resources, a survey was made of the methods used for identifying scrap metals. Because of the large number of alloys currently being scrapped, correct identification of these materials is essential if they are to be recycled effectively. The methods and instruments used to identify scrap metals are described and evaluated. These include object recognition, color, density, magnetic testing, spark testing, chemical spot testing, thermoelectric measurements, eddy current measurements, and elemental analysis by chemical and instrumental methods. Other potential techniques are discussed also.

Jan 1, 1982

By A B. Christie

Stream sediment geochemical analyses from 140 mining company exploration surveys of the Coromandel, Northwest Nelson, Marlborough and Westland regions of New Zealand have been compiled from open file reports and entered on a database called REGCHEM (for Regional Exploration GeoCHEMistry). REGCHEM is supported by GEOEXPL, a custom-written computer software application which operates under the Microsoft Access relational database management system on a PC-type computer, The data are plotted as maps using the MapInfo geographic information system (GIS) package. Thresholds separating anomalous values from background values are determined using the PROBPLOT uni-variant statistical package, which enables the discrimination and modelling of several populations. Relevant REGCHEM data are being incorporated into a GIS for the Coromandel region as part of ongoing studies to develop mineral deposit and metallogenic models for the region, and to assess regional prospectivity.

Jan 1, 1995

By Charles Deacon

The mining industry is constantly taking greater cognisance of their operating costs as a strategy to counter the effects of falling commodity prices. As a result, optimal operating efficiency is more important than ever. One such operation is that of blasting. Considering the relative increasing costs of explosives and accessories it is desirable to optimise the number of blast-holes fired by maximising their individual output. This achievement may now only be possible following the advent of higher technologies in the form of modified explosives and electronic detonators. This paper reviews and introduces some techniques of blast monitoring, types of operations where each is most suited, resulting modifications to blast designs, and identifies some pitfalls to watch out for when analysing the results.

Jan 1, 2000

Magnetic separation is an age-old technique for mineral beneficiation operations. The existing mathematical models for magnetic separators are quite complicated, and it is very difficult to measure the theoretical separation efficiency. The connectionist approach of modeling, to establish the relationships of the inputs and outputs, is preferred for this kind of problem. Experiments were carried out on a high-intensity roll magnetic separator to develop a database using four input variables (magnetic flux intensity, particle size, splitter position and roll speed) and two output variables (weight recovery and Fe recovery). The artificial neural network (ANN) and statistical methods (MLRG) were used to model the magnetic separation process. For the ANN, the regression coefficient (R2) values between the predicted and measured results were 0.89 and 0.94 for Fe recovery and weight recovery, respectively. Compared to ANN, the multivariable linear regression analysis showed inferior performance in predicting the weight recovery and the Fe recovery. The ANN models for the roll magnetic separator can predict the separation efficiency up to an acceptable limit. These models can be used to modify the operational parameters at mineral beneficiation plants to minimize the effects of variations in the raw material characteristics.

Jan 1, 2009

By Mark R. Svinkin

Construction vibrations may adversely affect surrounding buildings and their effects range from human discomfort and disturbance of sensitive devices to visible structural damage. There is no unique conclusion regarding the effect of construction vibrations at every site. Measurement is usually made to monitor vibrations and control them with the vibration thresholds for disturbance of sensitive objects as well as damage to structures. To prevent potential litigation and mitigate the vibration effects on sensitive devices, people and structures, it is necessary to manage and minimize vibration problems before the beginning of construction activities or installation of vibrating machine foundations, and during construction. Pre-construction damage survey and engineering vibration investigations, including the prediction of anticipating vibrations, have to be made at most construction sites in advance of construction activities. Vibration monitoring and control have to be provided during construction. The instrumentation feedback of vibration prediction, monitoring and control provide the basis for choice of measures to prevent or mitigate vibration problems and settlement damage hazards.

Jan 1, 2002

By R L. Langak, R A. Heins

The use of differences in specific gravity between minerals to separate them has long been utilized in the extractive industries. The environmental and cost benefits of the commercialized forms of these processes are well understood and widely used. Gravity concentration is used inter alia in the primary beneficiation of gold, diamonds, coal, tin, ferrous metal ores and andalusite. The potential for economic loss due to poor performance of these gravity processes is significant, but diverse in manifestation and regular process monitoring can prevent or at least reduce these losses. The measurement of performance of gravity processes has always presented a challenge, due primarily to the masses of material involved and the physical nature of the processes, generally typified by long reporting time, and hazardous materials (such as Tetrabromoethane) for float and sink type tests. The development of density tracers has improved this situation, however recovery of these tracers from the process streams created the next set of challenges, requiring significant manpower to physically remove tracers from product dewatering screens. Additions to these tracers (magnetic or x-ray fluorescent) eased the recovery mechanism issues but made them much more expensive to produce, hence operators became concerned about losses during process testing. In addition, magnetic recovery of smaller size tracers by a magnet suspended above a loaded screen panel is still problematic. The development of new low cost magnetic tracers has improved statistical significance of tracer tests, as the tracers themselves can be bought and used in much larger quantities, whilst still remaining economically viable. Coupled with the development of effective magnetic recovery technology, such as the Gekko MagScreen, for even fine sized tracers, on-line, continuous tracer testing is now becoming a reality. Whilst the development of high technology radio frequency detection tracer systems continues, enabling the real time measurement of the process and interpretation of results, miniaturization and recovery of these tracers, which is critical given their costs at present, remains an issue. Keywords: Gravity, process measurement, tracers, magnetic recovery

Jan 1, 2006

By Derek Ellis

Volume II of this two-part series on Submarine Tailings Disposal (STD) as a tailings management option for coastal and island mines contains descriptions of lesser known case histories. The Misima gold mine (Papua New Guinea) and the Black Angel lead-zinc mine (Greenland) are described in some detail as the best documented cases. Atlas copper mine (The Philippines) is less fully described due to relative lack of documentation. The Misima and Atlas STD systems are working to their design criteria. At Black Angel the system adopted did not prevent contamination for a number of reasons, which are now understood. Two cases are described where STD is being developed. They are the Cayeli Bakir copper mine Turkey), and the Toquepala and Cuajone mines (Peru). There is excellent documentation available for both cases. Three case histories are described where tailings have reached the sea either through beach or river discharge. In one case the STD option has been explored (Marcopper Mine, The Philippines). In the others we explore in hindsight whether STD might have been a viable alternative using the Screening Criteria that this Volume develops - see below. The mines are Bougainville Copper Mine in Papua New Guinea, and Jordan River Mine (Canada). There is potential for STD at all three sites. Finally, the Volume presents Screening Criteria for appraising STD, based on the experience in design, operation and environmental impact reviewed in the case histories.

Jan 1, 1994

By Eti Purwaningsih, Widi Astuti, Erik Prasetyo

Selective-reductive leaching of manganese from low-grade manganese ore using tannic acid as a reductant in acidic media was demonstrated by XRD, SEM-EDX characterization, and batch leaching studies at room temperature. The pH change in the liquid phase before and after leaching revealed that selectivity of manganese over iron was due to the hydrolysis of iron. The acidity in the liquid phase during leaching was dictated by two mechanisms: proton-consuming reaction (manganese oxide reduction by tannic acid) and proton-producing reaction (ferric ion reduction by tannic acid to produce ferrous ion). Based on the leaching studies, the more prevalent reaction between these two was determined by initial leaching conditions: tannic acid concentration, sulfuric acid concentration, liquid-solid ratio, temperatures, and agitation time. Kinetic studies revealed that maximum recovery was attained within 6-h agitation, which indicated a product layer diffusion process.

By Eti Purwaningsih, Widi Astuti, Erik Prasetyo

Selective-reductive leaching of manganese from low-grade manganese ore using tannic acid as a reductant in acidic media was demonstrated by XRD, SEM-EDX characterization, and batch leaching studies at room temperature. The pH change in the liquid phase before and after leaching revealed that selectivity of manganese over iron was due to the hydrolysis of iron. The acidity in the liquid phase during leaching was dictated by two mechanisms: proton-consuming reaction (manganese oxide reduction by tannic acid) and proton-producing reaction (ferric ion reduction by tannic acid to produce ferrous ion). Based on the leaching studies, the more prevalent reaction between these two was determined by initial leaching conditions: tannic acid concentration, sulfuric acid concentration, liquid-solid ratio, temperatures, and agitation time. Kinetic studies revealed that maximum recovery was attained within 6-h agitation, which indicated a product layer diffusion process.

By G. W. Jones

As part of its program for the promotion of safety, the Bureau of Mines has investigated various means of mitigating or eliminating the explosion hazards of combustible gases and vapors found in the mining and other industries. Knowledge as to the explosive characteristics of cyclopropane in air, oxygen, and other gaseous mixtures is of both theoretical and practical importance because cyclopropane is now used extensively in anesthesia. As such an agent it has many desirable characteristics, and increased consumption of this gas may be expected if the explosion hazards now attending its use can be minimized or eliminated. The present practice of using mixtures of approximately 20 percent cyclopropane and SO percent oxygen should be discouraged because such mixtures are violently explosive and have led to fatal accidents.

Jan 1, 1940

By G. W. Jones

As part of its program for the promotion of safety, the Bureau of Mines has investigated various means of mitigating or eliminating the explosion hazards of combustible gases and vapors found in the mining and other industries. Knowledge as to the explosive characteristics of cyclopropane in air, oxygen, and other gaseous mixtures is of both theoretical and practical importance because cyclopropane is now used extensively in anesthesia. As such an agent it has many desirable characteristics, and increased consumption of this gas may be expected if the explosion hazards now attending its use can be minimized or eliminated. The present practice of using mixtures of approximately 20 percent cyclopropane and 80 percent oxygen should be discouraged because such mixtures are violently explosive and have led ,to fatal accidents.

Jan 1, 1940

By Malcolm Powell

"The argument has long raged across the oceans as to what the best AG/SAG mill aspect ratio is. The North American practice of a high aspect ratio of two, diameter twice length, through to the South African and Scandinavian practice of an aspect ratio of as low as a 0.5. Within the collaborative P9 AMIRA project the MPRU of the University of Cape Town and the JKMRC of the University of Queensland have been collecting plant data pertinent to this issue over the past four years.The JK SAG mill model developed by the JKMRC is based upon data collected from mills having a range of aspect ratios from 1 up to 2. The maximum mill speed, mill load, and ball filling in the fitted data base were all below the operating range common in South Afr-ica. The extension of the P9 project into South Africa therefore lent an ideal opportunity to collect data in a whole new window of operation that would allow the range of applicability of the semi-empirical SAG model to be greatly extended.At the heart of the differences in aspect ratio is the completely different operating practice for high- and low- aspect mills. The mill filling, mill speed, and recirculating loads of closed-circuit single-stage operation have more influence on the differences in operation than the pure aspect ratio relationship. Relationships for load have been extended to 45% filling, with the modified model showing the measured peak in throughput as the mill filling increases. The ball load relationship now covers fillings of over 30% balls (of total mill volume), thus including so-called SAG-ball mills. The influence of closed circuit operation has been measured. It has been found that a key issue of the high slurry flows associated with closed circuit operation, especially when closed with a cyclone, is the pulp discharge limitation of the traditional grate and radial lifter configuration. It has also been observed that absolute mill length is more of an issue than aspect ratio. Slurry flow along the mill and charge segregation within the load are being investigated on pilot and full-scale mills to provide data for potentially modifylng the perfect mixing model that is used for the SAG mill.Improved understanding of these aspects of SAG mill operation and extension of the JK SAG model to better cover the entire range is allowing serious direct comparison of high- and low aspect mills for the first time. It is the conclusion of the researchers working in this area that there is no one best practice, that in fact mills across the range have their application based on ore type, desired product, available capital and on operating costs. Developing robust designs allows direct comparison of two-stage circuits using high-aspect primary SAG mills, with single-stage closed circuit low-aspect SAG mills. The new operations within South Africa are now considering both circuit types, and data is presented on selections that cover the full range of aspect ratio and operating practice."

Jan 1, 2002

By E. C. Tarpley

An acid-extraction procedure developed in Germany for determining mineral matter in coal was investigated by the Bureau of Mines to determine its application to American coals. It was found to be suitable for all ranks of coal from anthracite to lignite if modified slightly for coals containing considerable quantities of calcium compounds, such as calcite or calcium humate. The precision of the method is satisfactory, and the results are probably closer to the true content of mineral matter than those obtained by empirical formulas. The method requires considerably more analytical data than the Parr or approximation formulas but is no more time consuming than obtaining the necessary data for the King, Maries, and Crossley formula (theoretically the most comprehensive empirical formula used). An appendix to this report includes a detailed description of a recommended procedure.

Jan 1, 1959

Although the Diamond that is cut and polished and made up into an article of jewellery, is so well known, there are, comparatively speaking, very few outside the industry who know this beautiful crystal in the crude state, as turned out ofNature's laboratory, and the means employed in winning this precious stone.This article is written with the endeavour to give the reader some idea of the geological formations in which the Diamond occurs, and as it is reported that Diamonds have been found in Western Australia, as well as in other parts of the Australian Colonies, a few hints as to the means employed in working the ground in South Africa may be of use to those intending to prqsecute the search in this country. The general geological formation of the South African Diamond Fields is Lacustrine shales and sandstones, intersected by dykes of various eruptive rocks, varying considerably in their character. and in places vesicular in texture, the vesicules being more or less filled in with zeolites by permeating waters.

By E. M. Murphy

Comparative data from ASTM method of test E-162 and large-scale trials in the Experimental Mine show that the flame-spread quality of brattice cloth and other ventilation control materials can effectively be evaluated by either method. Materials having a flame spread index of 25 or less, as determined by the simpler and more economical laboratory test ASTM E-162, do not present a serious fire hazard when used in coal mines.

Jan 1, 1972