Search Documents

By Tobias Dubberstein, Hans-Peter Heller

The viscosity of Fe-Cr-Mn-Ni TRIP/TWIP (Transformation Induced Plasticity, Twinning Induced Plasticity) steel with varied nickel content is investigated using a vibrating finger viscometer. The viscosity of the melt is calculated from the change in power input in the field coil by an immersed finger into the liquid steel to maintain a constant peak-to-peak amplitude of the sine wave of oscillator compared to the idle state. Nickel content in steel is varied from 3 wt% to 9 wt%. The dynamic viscosity (η) at 1600 °C for 3 wt% Ni is 3.73±0.14 mPas, for 6 wt% Ni 3.50±0.03 mPas, and for 9 wt% Ni 3.93±0.09 mPas. There is a kink from low to high nickel content in viscosity values of Fe-Cr-Mn-Ni alloys. This phenomenon can be explained by a change in coordination number in the melt, as reported for Fe-Ni binary system in literature. The availability of viscosity data delivers relevant input to model free fall atomization processes of FeCrMnNi alloys.

Jan 1, 2015

By Elizabeth M. Ho

Oxidants are added in uranium leaching in acid media to convert iron(II) in solution to iron(III). Iron(III) has an important role in the leaching of uranium by acting as an electron transfer agent for the oxidation of uranium(IV) to uranium(VI). The oxidation of iron(II) to iron(III) in sulfate solutions using sulfur dioxide/oxygen (SO2/O2) was carried out under typical uranium leaching conditions (pH 1-2, 20-50°C) to confirm literature trends and this work was then extended to the use of SO2/O2 in the leaching of uranium ore. The oxidation rate was found to be dependent on the initial SO2/O2 volumetric ratio and the oxygen mass transfer rate, but was independent of the initial iron(III) concentration above about 200 ppm at pH 2. The presence of 55 ppm organic extractant (Alamine 336) decreased the reaction rate. The oxygen mass transfer coefficient (kLa) for the mixing tank system was measured and was found to decrease with increasing solids density in a 1 g L-1 MgSO4.7H2O solution.

Jan 1, 2003

By Kouji Mimura, Manabu Kishida, Minoru Isshiki

"Purification of metallurgical grade silicon (MG-Si) by the plasma-arc zone melting method (PZM) has been examined. The process consisted in the horizontal displacement of a molten zone heated by Ar- and 10%H2+Ar- plasma-arc under atmospheric pressure. This technique, especially using hydrogen plasma-arc, promoted the segregation of impurities from the head to the tail of the bar and the vaporization of impurities of higher vapor pressures. Metallic impurities such as Fe, Ti, Cr, Mn,. Cu, Al and Ca were reduced to less than 1 mass ppm at the head side of the Si bar. Non-metallic impurities such as boron, phosphorous, carbon and oxygen were also reduced by the zoning effect and, furthermore, by activated hydrogen atoms dissociated in the high temperature plasma-arc according to the following reaction: Q (in liq.Si) + 2H = H20. Plasma-arc zone melting with hydrogen plasma has been recognized to become an effective purification technique of MG-Si for the production of a low cost solar grade Si (SOG-Si).IntroductionDemand of high-purity Si for solar grade silicon (SOG-Si) is supposed to be further growing in the near future. The purity of SOG-Si required for the photovoltaic cell is more than six nines. An expensive semiconductor grade silicon (SEG-Si) with the purity of around eleven nines has been used to satisfy the demand. Development of techniques and processes for the production of a low cost SOG-Si is therefore necessary [l]. Although many purification techniques, such as directional solidification, plasmaarc melting and electron beam melting [1-6], and processes, such as carbothermic reduction of high purity silica [7], have been examined and proposed for this purpose, a more efficient and practical purification technique is still required.In the present work, the purification of MG-Si has been investigated using a plasma-arc zone melting (PZM) technique developed by the authors. Plasma-arc melting, which is well· known as a useful melting method for various metals and alloys, has been recognized to be efficient for refining and degassing several metals if hydrogen is added to the plasma generating gas, resulting in the so-called hydrogen plasma-arc. For example, deoxidation of Fe, Co and Ta [8,9], decarburization of Fe [9] and removal of metallic impurities from Zr, Ta and Fe [10-12] have been reported. This excellent refining effect is considered to be caused by dissociated and activated hydrogen atoms formed in the high temperature plasma-arc."

Jan 1, 2000

By Wang Zhi

High-Mg-content concentrates are usually treated in Jinchuan flash smelting Furnace. Because the viscosities of high-Mg-content slag is very high, the operation of flash smelting becomes very difficult. To solve this problem, the viscosities of the semi-synthesized FeO-MgO-Si02 slag of different compositions were measured. The results showed that when in the slag the weight percentage of MgO [m(Mgo)] is 6-10%, the ratio of the weight percentage of iron to that of Si02, m(Fe)/m(SiO2) is 1.1-1.4 and the temperatures are within 1473?1773K, the slag viscosities increased with the increase of m(Mgo) and m(Fe)/m(sio,). When m(Mgo)<6%, the smelting temperature should be controlled at I 300°C in order to to keep the smooth operation. When m(Mgo» 10%, the temperature should be kept above 1633K. When the content of MgO is higher, a lower viscosity slag ean be produced by decreasing the ratio of m(Fe)/m(sio,). The appropriate ratio of m(Fe)/m(sio,) for Jinchuan flash smelting furnace is about 1.2.

Jan 1, 2003

By Kafui Nyavor

The indirect, and the direct contact mechanisms of bacteria oxidation of sulfides were studied using Thiobacillus ferrooxidans and pyrite. The aim was to determine which of the two generally aeeepted mechanisms played a dominant role, if any, during acid mine drainage (AMD) formation from the oxidation of sulfide minerals. The results show that at a pH of 4.5 where T. ferrooxidans are quite active, but where initial chemical oxidation of pyrite to Fe2+ is limited, the bacteria were unable to directly oxidize pyrite to any significant extent. Whereas, in the presence of Fe2+, T. ferrooxidallS assisted oxidation of pyrite by the indirect mechanism was observed and sustained over the pH and Eb range where the bacteria is active. The results lead to the conclusion that the direct contactmechanism of pyrite oxidition by T. ferrooxidans is insignificant. The predominant, and possibly the only, pathway involves the indirect bacteria oxidation of available Fe2+ to Fe3+, which in turn oxidizes FeS2 to generate additional Fe2+ and acidity in a cyclic process.

Jan 1, 1996

By Nobuhiro Kuriyama

Electrochemical activation behavior of an AB2-Laves-phase type hydrogen storage alloy, Zr0,9Ti0.lNi1.lCo0.1Mn0.6V0.2 was studied to make clear activation process of pellet-type metal hydride electrodes. An alkaline treatment of the electrodes with heated alkaline solution gave alloy surface enriched with nickel, and the treated electrode was more easily activated. The treated electrode desorbed more hydrogen during the first charge-discharge cycle, and was activated without induction period. A cross sectional view of the activated electrode showed finer pulverization of alloy particles than the annealed alloy, and impedance spectroscopy indicated larger surface area of the electrode using the as-cast alloy. Since the as-cast alloy contains inhomogeneities, multi-phase microstructure and stress in the particle, the finer pulverization of alloy particles with hydrogenation are considered to increase surface area in an earlier cycle in the case of the as-cast alloy, which leads larger reaction area and faster activation of the as-cast alloy electrode.

Jan 1, 2002

By lchiro Aoi, Hideo Nakae, Makoto Yoshida, Makoto Ishino

"The influence 6f gravity on the microstructure of unidirectionally solidified Cu-Pb monotectic, Ag-Si and Fe-C eutectic alloys is studied. In order to examine the influence of gravity in a lg environment, both the upward (opposite to direction of gravity) and downward (direction of gravity) unidirectional solidifications are carried out. The results are as follows: (1) For the upward solidified Ag-Si eutectic alloy, the eutectic Si continuously grows. On the other hand, in the downward solidified Ag-Si alloy, the Si grows discontinuously and disperses into the ex-Ag matrix. (2) No morphological difference in the eutectic growth is observed between the upward and downward solidified Fe-C eutectic alloys. (3) In the case of the upward solidified Cu-Pb monotectic alloy, a banded structure, which consists of Pb-rich layers and Cu-rich layers, is observed. However, such a banded structure -is not observed in the downward specimen. (4) The banded structure is not found in the upward solidified Cu-Pb-0.05 mass % Al and Cu-Pb-0.1 mass % Al alloys. In the Cu-Pb-0.05 mass% Al alloy, a fibrous -L 2 phase grows continuously parallel to the growth direction at low growth rate. Only 500 mass ppm addition of aluminum induces the morphological change of the monotectic L2 phase.IntroductionThe influence of gravity on the solidification of eutectic and monotectic alloys has been investigated in microgravity environments [l-9]. The purpose of these studies was to obtain a homogeneous microstructure of eutectic or monotectic alloys, most of which alloys tend to solidify with macro-segregation under gravity. However, in most of the previous experiments, e.g., in free fall systems, in aircraft or in space laboratories, the growth rate was too high to realize a planar solid/liquid interface. This would be due to the limited time for solidification. Thus, it was difficult to examine the influence of gravity on the planar coupled growth of the eutectic or monotectic alloy. In this study, both the downward U.D.S. (unidirectional solidification by gravity) and upward U.D.S. (opposite direction to gravity) are carried out in order to examine the influence of gravity on the coupled growth in a lg environment [l0, 11]. In the case of the downward U.D.S. using the current Bridgman method, the molten alloy must be confined between the crucible and the solid."

Jan 1, 2000

By Enrui Dai, Weibing Chen, Bin Yang, Wenhui Ma, Haisheng Fang, Hui Wang

LiMn0.8Fe0.2PO4/C composite was prepared by an improved solid-state method and the effect of calcination temperature on properties of the obtained materials was investigated. The results showed that increasing calcination temperature from 600 to 700 oC improved the performance of the LiMn0.8Fe0.2PO4/C due to enhanced crystallinity and increased conductivity, but further increase in calcination temperature to 800 oC led to degraded performance due to particle growth and decrease in porosity. Therefore, the LiMn0.8Fe0.2PO4/C composite prepared at 700 oC exhibited the best electrochemical performance, and could deliver a high capacity of 152 mAh g−1 at 0.1 C, 147 mAh g−1 at 1 C and 114 mAh g−1 at 10 C. In addition, the performance of the LiMn0.8Fe0.2PO4/C and LiMn0.8Fe0.19Mg0.01PO4/C was compared when they were obtained at the optimum calcination temperature.

Jan 1, 2015

By Malti Goel

"Ferrous and non-ferrous metals industries are source of both direct and indirect greenhouse gas (GHG) emissions. Metal industry accounted for 29.7% of the total GHG emitted from the Indian industry sector in 2007. Aluminum is second largest contributor after steel. Indian Aluminum industry has been growing and is adopting several effective measures for better efficiencies through process change and waste utilization. Improvement in the energy efficiency can form the basis of monitoring reduction in emissions. Under the National Action Plan on Climate Change 2008, National Mission for Enhanced Energy Efficiency (NMEEE) aims to upscale the efforts to unlock the market for energy efficiency improvement on a public private partnership (PPP) basis. For a transition to low carbon economy industry is undertaking voluntary measures through scientific and technological innovations both in upstream and downstream sectors. In this paper an attempt is made to overview recent developments in Indian Aluminum industry as well as summarize scientific & technological challenges and prospects.IntroductionAluminum plays a vital role in industrial development. It is a substitute for different type of materials ranging from wood to copper and steel. The aluminum industry has high energy consumption and high contribution to greenhouse gases from carbon dioxide and perfluorocarbons (PFCs) emissions. It is estimated that CO2 equivalent burden of aluminum industry is about 1% of total anthropogenic emissions. The anticipated world growth rate is 3.5% for aluminum demand. Through measures to reduce both direct and indirect CO2 emissions, electricity consumption was reduced from 25 kWh / kg of Aluminum in 1998 to 15 kWh / kg of Aluminum produced in 2008. It is targeted to further reduce it to 10.8 kWh. Aluminum industry is also responsible to about 60% of all PFC emissions. The PFC emissions are harmful to environment, accumulate in surrounding vegetation and contaminate. Efforts to reduce PFC emissions from aluminum industry started early and reduced to 0.5-1 kg / tonne in 1990 [1] from 12-15 kg / tonne in 1940. Since 1990s to 2000 it further reduced to 0.2 -0.4 kg / tonne as seen in Fig. 1. The Global Aluminum Sustainable Development Initiative (GADSI), targets perfluorocarbon (PFC) specific emissions reduction of 80% for 2010 relative to 1990."

Jan 1, 2011

By Ehsan Vahidi, Fereshteh Rashchi, Ataollah Babakhani, Alireza Zakeri

"The synergistic effect of Cyanex 302 on solvent extraction of nickel and cadmium from sulfate solution with D2EHPA diluted in kerosene was investigated with the aim of increasing separation efficiency. Experiments were carried out within a pH range of 0.1-5.0 using sole D2EHPA and D2EHPA-Cyanex 302 mixtures in different ratios. Increasing Cyanex 302 to D2EHPA ratios in the organic phase caused a left shifting of the extraction isotherm of cadmium and a right shifting of the extraction isotherm of nickel. As a result, optimum separation was found with a Cyanex 302 to D2EHPA ratio of 0.1M:0.5M. In the present system, effect of a modifying reagent such as TBP was studied. The influence of various diluents including kerosene and carbon tetrachloride was also investigated.IntroductionBatteries are popular sources of portable energy. Ni-Cd batteries are manufactured in two main groups of small domestic cells and large industrial batteries with 80% being in domestic use. Ni-Cd cells have various uses, for example in cordless electric utensils, cordless telephones, airplane engine starters, and communicational distribution systems [1].Depleted Ni-Cd batteries are classified as hazardous waste since nickel and cadmium are heavy metals and suspected carcinogens. Given the risk associated with uncontrolled disposal, directions for issuing legislation on disposal and recycling of used batteries have been made in industrialized countries [2]. Recycling of Ni-Cd batteries is important from both economic and environmental points of view. Different methods have been used for recycling these wastes through pyrometallurgy [3], biotechnology [4,5], and hydrometallurgy [1,2].Due to the advantages of hydrometallurgical processes, several studies have been implemented on leaching and solvent extraction (SX) of the used Ni-Cd batteries. Leaching of batteries is usually done in sulfate or chloride media; while solvent extraction has been used in different extractants: two-stage solvent extraction by D2EHPA and Cyanex 272 [6]. Solvent extraction of Cd from leach solutions has been studied using various extractants; Cyanex 301 [1], D2EHPA [7], Cyanex 302 [8], Cyanex 923 [9], Cyanex 272, Tops 99, PC88A [10]. Application of phosphorus based extractants for the solvent extraction studies of Ni such as TOPS 99 [11], D2EHPA [12], Cyanex 272 [2], has been investigated. Separation of Cd(ll), Ni(II), and Co(ll) from chloride leach liquor of spent batteries [13], were explored in the earlier studies. Cd extraction with D2EHPA involves co-extraction of both Ni and Co [14], which causes issues in the separation process efficiency."

Jan 1, 2012

By C. A. Young, J. D. Miller

Adsorption isotherms previously determined by in-situ Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS) for oleate adsorption at calcite and fluorite surfaces near pH 9 and at various temperatures are compared. Results indicate that, at both mineral surfaces, chemisorption occurs at equilibrium concentrations below approximately l x l0-5 M oleate while calcium dioleate surface precipitation occurs at higher equilibrium oleate concentrations. The extent of chemisorption at the calcite surface is 3 to 5 times less than that at the fluorite surface while the extent of calcium dioleate surface precipitation on calcite is nearly a magnitude larger than that on fluorite. However, for both minerals, surface precipitation decreases with increasing chemisorption. Contact angle measurements and flotation recoveries show the hydrophobicity of fluorite to be greater than that of calcite at each of the temperatures and oleate concentrations studied. Significant differences are noted only in the chemisorption region. Unlike calcite, the hydrophobicity of fluorite was sensitive to the presence of oxygen in the system. Multichannel Laser Raman Spectroscopy (MLRS) showed this behavior was caused by the double-bond reactivity of adjacent chemisorbed oleate molecules and subsequent formation of an epoxide/polyether complex at the fluorite surface. Such a reaction product could not be detected at the calcite surface. These differences in adsorption density, hydrophobicity, and polymerization behavior are discussed in terms of the intrinsic surface properties of the minerals.

Jan 1, 1999

By John E. Dutrizac, Tzong T. Chen

"Laboratory experiments were undertaken to ascertain the behaviour of various ""impurity"" species during the precipitation of hematite directly from ferric sulphate solutions at 225°C and in the presence of 40 or 50 g/L of hematite seed. Copper, nickel and zinc are not significantly incorporated in hematite precipitates. Although the nickel contents increase to 0.22% as the Ni concentration increases to 60 g/L, the solid solution Ni contents are low relative to the bulk Ni contents. Thus, part of the Ni may be present as tiny particles of poorly soluble NiS04.H20. Increasing germanium concentrations to 2,000 mg/L result in products containing up to 0.59% Ge. The Ge occurs either in solid solution in the hematite or is adsorbed on the nanometer-size hematite crystallites. Increasing As(V) concentrations to 10 g/L increase the AsO4 contents of the products up to 16%. However, the products consist of hematite together with As04-containing Fe(SO4)(OH) and an unknown Fe-AsO4 species. All the hematite products contain - 1% SO4 which appears to be adsorbed on the nanometer-size hematite crystallites.IntroductionDissolved iron is a common impurity in most hydrometallurgical processing circuits and, generally, the iron must be eliminated prior to the subsequent recovery of the sought after metals. Simple neutralization of iron-rich solutions yields slurries which are difficult to thicken and filter. To address these concerns, the jarosite, goethite and hematite processes have been developed, and these technologies are able to reject the dissolved iron in a readily filterable form [1]. Despite its higher cost, the hematite process offers several potential advantages. Because hematite is an iron-rich, high-density compound, its formation would reduce the mass of residue and the size of a residue storage pond. Hematite is the thermodynamically stable form of iron under ambient conditions, and this stability would facilitate the impoundment of hematite precipitates. Furthermore, hematite has some market potential for cement manufacture and even for iron making [2]. In all the commercial hematite processes, the dissolved ferric ions are first reduced to the ferrous state. Subsequently, the pH of the solution is adjusted and the solution is then oxidized. The ferric ions gradually generated during solution oxidation hydrolyze and precipitate mostly as hematite, although commercial hematite products also contain trace or minor amounts of jarosite-type compounds. However, there are potential advantages in precipitating hematite directly from ferric ion solutions, as the reduction and subsequent oxidation of the iron are not required. Although the precipitation of hematite directly from relatively concentrated ferric sulphate solutions (up to 0.5 M Fe(SO4)is) was recently demonstrated [3], the behaviour of impurity species during hematite precipitation is largely unknown. To address this issue, systematic laboratory experiments were undertaken to ascertain the behaviour of a number of ""impurity"" species during the precipitation of hematite directly from ferric sulphate solutions at 225°C, and the results are presented in this paper."

Jan 1, 2012

By Tatsuzo Kitamura

The tank house of Tamano refinery, that started its operation in January, 1972, was constructed incorporating the application of Periodic Reverse Current (P.R.C.) from the outset of design works. In 1973, the production of electrolytic copper came up to 8,000 mtpm, a sharp increase ds compared with the designed capacity of 7,000 mtpm, and successful operation has been achieved up to the present. P.R.C. has been employed for the purpose of raising productivity level and reducing copper inventories. Since there were various problems in P.R.C. application to such a large sized cathode as 1 m x 1 m, special attentions were paid to the following items: -Development of a unique bus bar to make an electrolytic current to each electrode as uniform as possible. -Improvement of circulating method of electrolyte. -Application of high-performance equipment to realize a uniform spacing between anode and cathode. Owing to these creative technical developments mentioned above, technical level for operation up to 350 amp per sq m of cathode current density has been established. The quality of electrolytic copper, which was a matter of interest, has been proved to be as excellent as those of conventional electrolysis products through a long term supply to the field of SCR and Dip forming where high levels in quality are required.

Jan 1, 1976

By Dimitrios Fillippou

Magnesium hydroxide is used in a number of industrial applications, from the neutralisation of acid effluents to the production of pharmaceuticals. High-quality magnesium hydroxide powders can be produced by hydrating slow-reacting magnesia in dilute magnesium acetate solutions. The process of magnesia hydration shows many similarities with a typical hydrometallurgical leaching operation; however, its kinetics are crucial not only for process design and control, but also for the production of powders with a desirable particle morphology. This article shows the results of an experimental work whereby industrial heavily-burned magnesia powders were hydrated in 0.01 to 0.1 mol/L magnesium acetate solutions at temperatures ranging between 333 and 363 K. Examination of the magnesium hydroxide produced and the analysis of the kinetic data suggest that the hydration of heavily-burned magnesia in magnesium acetate solutions is a dissolution-precipitation process controlled by the dissolution of magnesia particles. The activation energy was estimated to be 60 kJ/mol, while the reaction order with respect to magnesium acetate concentration was found to be about one.

Jan 1, 1999

By Kimio Ilagaki

The distribution ratios of Ag, Pb, As, Sb and Bi for the Cu2S-FeS or Ni3S2-FeS matte I FeOx-SiOl, FeOx-Si02-CaO or FeOx-CaO slag equilibration in a MgO crucible were determined experimentally at 1523 ~1573K under controlled partial pressures of S2 and 02 at given PS02 of 10.1,50.7 and 101.3 kPa(O.I, 0.5 and I atm), and the observed dependency of distribution ratio on the matte grade, S02 pressure and slag basicity were analyzed on the basis of thermodynamics.

Jan 1, 2003

By Dhanesh Chandra

Long term stability studies were conducted on four variants of LaNi5; 10,000 hydriding/dehydriding cycles were used to evaluate their suitability for a metal hydride cooling system. Thermodynamic and structural studies were conducted to determine changes in these materials during cycling test period. The hydrogen sorption properties of LaNi5.2, and Lao 9Gd0.1Ni5 and LaNi4.75In0.27 were seriously degraded during the tests but the LaNi4.8Sn0.22 hydride was virtually unaffected. Hydride isotherms were measured at the beginning and at intervals through out the test period to observe the nature and extent of damage degradation in the sorption properties. X-ray diffraction studies of the alloys (LaNi5.2, LaO.9Gd0.1Ni5 LaNi4 8Sn0.22) and their respective hydride, before and after test, provided insight with regards to the observed changes in the hydride properties. Electron microscopic studies were also conducted to evaluate the changes in particle sizes.

Jan 1, 1989

By Peter Ehren

Global Geoscience is developing a Rhyolite Ridge project, a shallow boron-lithium resource deposit, located in Nevada about 25 km from Albermarle’s Silver Peak operation. The main minerals of interest are the boron mineral searlesite (40%wt) and lithium containing clay minerals. These minerals are found among principally calcite, feldspar, muscovite, dolomite, and quartz. The equivalent commercial value is about 7–9% boric acid (H3BO3) and 0.8–1.0% lithium carbonate (Li2CO3) equivalents. Selective agitated leach tests at SGS Lakefield laboratory showed that searlesite can be acid leached between 20 and 75 °C and at a pH lower than 4. On the other hand, lithium can be leached between 20 and 75 °C and at a pH lower than 1. In other words, lithium can be recovered at low temperatures if sufficient free acid is available, which gave the motivation to investigate heap leaching of the mineral. The PLS contains boric acid, magnesium, sodium, lithium, potassium aluminium, and iron sulfates.

By Marco Antônio Siqueira Rodrigues

The possibilities for treating rinse waters fiom chromating bath by electrodialysis are discussed together with the possibilities of optimizing the treatment process for waste reduction and reuse of water and chemical products. An industrial effluent with 4600 ppm of Cr(VI), besides other metallic contamination, was used as work solution. This solution has been recirculated on an electrodialysis cell of three compartments, using exchange membranes Selemiom AMT and CMT. A migration of dichromate ions into the anodic compartment was obtained, so that an extraction of circa 99.9 % of Cr(VI) present on the solution was observed, resulting in water with a Cr(V[) concentration of 4 rnd. These results show that electrodialysis can be used to treat these effluents, and this water could be reused as rinse water. The solution of the anodic compartment, consisting at the beginning of the experiment of H2S04, 0.1 N, reached 7200 mg/l of Cr(VI). This concentrate could be reused on the chromating bath itself.

Jan 1, 1999

By Animesh Jha

"Fine ceramic powders (<500 nm) exhibit exceptional physical and mechanical properties in engineered structural ceramics. The production of fine powders, in particular the non-oxide ceramics, via a cheaper route than the organic solvent route has been rather elusive. This paper examines the physical chemistry of sub-oxide vapour-phase reduction reaction for the nucleation of non-oxide ceramic phase. Well known vapour species eg SiO and BO in the production of technical ceramic powders (SiC, BN) are particularly discussed for understanding the nucleation process of SiC and BN ceramic phases respectively. The regimes of partial pressures and temperatures are particularly 'identified. The calculated nucleation rate as a function of the temperature is compared with the experimental results on powder morphology. The production of amorphous and nanocrystalline h-BN powders is discussed in the context of substrate structure and thermodynamic parameters.IntroductionThe physical and mechanical properties of ceramic components are strongly dependent on the powder particle size and morphology used for their fabrication. For example the strength (Os) of the structural ceramic components increases with decreasing average grain-size (d) in accordance with the Hall-Petch relationship: Os = 0""0 + k/(d)1/2. Here k is an empirical constant which can be established from the graphical relationship. However as the particle size approaches submicrometer-size range, the dependence of strength on the particle size becomes more complex [1]. The design of ceramic components based on nanometer-size particles have recently become an important field which can offer ceramic materials with properties comparable to their metal counterparts. Several materials based on these concepts have been developed and reported by Niihara [2]. For example, the Al2O 3-SiC nanocomposite, having average B-SiC grain size 0.3-2um with intragranular SiC particulates of 5-10 nm has unusually high strengths (1100 MN/m2) at low and elevated temperatures combined with enhanced fracture toughness (> 4 MN-ml.5) which is an unusual combination in structural ceramics. Besides mechanical properties, as the particle size of ceramic powders approaches the nanometer-size range, the charge transport properties also improve by many times. The effect of particle size on the electrical conductivity of Si3N4-TiN composites has been well documented [3.4]. The size of ceramic particulates without doubt plays a pivotal role in determining the properties of ceramic components."

Jan 1, 1996

By Hideki Yamamoto

A new technology to convert fluoride gas (C2H2F4 ; R-134a) contained in the exhaust gases from semiconductor manufacturing plants and refrigerators directly into a harmless substance have been established, thus, presenting a new concept for the disposal of fluoride gases such as CFCs that are associated with the global warming. Experimental results verify that chemical reactions with metal compounds can take place at substantially lower temperatures of 700- 800K as compared with combustion. treatment temperatures of 1200-1500K. The reaction product is mainly metal fluoride, which chemically is a harmless material. Furthermore, this process is compact, easily controlled, safe and has low running costs. This paper deals with a new chemical reaction method for the harmless disposal of gases effecting the global warming.

Jan 1, 2003