Search Documents

By A. Mikula, S. Karlhuber

"Unique physical and mechanical properties made the Pb-Sn solders attractive for low temperature joining of electronic parts. But since lead in solder materials has become a great enviromental problem and health concern, lead will be slowly replaced by other materials in soft solders. Some of these materials which are currently under investigation are ternary tin alloys. Many different physical properties like wetting behavior, electrical and thermal conductivity and surface tension are measured on these alloys, but on the thennodynamic properties and the phase diagram of the alloys under discussion there is only little information available. We investigated the (Ag, Au, Cu)-Sn-Zn systems and determined the thermodynamic properties over the whole composition range by emf-measurements. From these measurements we also got some information on the liquidus. In the Sn-rich corner the phase diagrams are still under investigation.IntroductionSoldering is technically defined as the joining of two base materials, mostly metals or metal coated nonmetallic substrates, with a third metal. The melting temperature of the third metal or metal alloy should be well below those of the substrates. Solder alloys can be categorized in soft and hard solders. Soft solder alloys usually contain lead, tin, bismuth, indium or cadmium and hard solders gold, zinc, aluminium or silicon. The difference between soft and hard solders is the melting temperature of the soldering material. This temperature is around 350°C.An interesting brief history of solders is given by Vianco and Frear [1]. They report, that in 4000 B.C. solders were already used in Mesopotamia. From archaeoligical evidence those solders were gold-based hard solders.Tin-lead soft solders and their use are not easily found, because in course of time tin has been reduced to stannic acid, making the identification quite difficult. Well preserved soft solder artifacts were discovered in King Tut's tomb dating from 1350 B.C. In ancient time Pb-Sn solders were used primarily for the manufacture and repair of cooking utensils and metal tools. The Romans used lead-tin solders extensively in the construction of the aqueducts."

Jan 1, 1996

By Mikula Adolf

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of temary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth. silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe. element.

Jan 1, 2003

By K. Yamaguchi, Y. Takeda

"Partial pressure - temperature - composition correlation diagrams of the Ga-As, In-As, Ga-P and In-P systems were contracted based on the obtained experimental data of the phase diagram and thermodynamic properties for the III-V systems. The total vapor pressures of arsenic or phosphorus at melting point of GaAs, InAs, GaP and InP were determined as 101, 10.1, 1510 and 253 kPa, respectively, at the corresponding melting points of 1509, 1211, 1739 and. 1336K , These diagrams are applied to the analysis of the horizontal Bridgman method and the liquid phase epitaxial growth technique. On the other hand, the analysis of the equilibrium state of the. chloride-CVD process was carried out using the data of the Gibbs energy of the compounds obtained by· authors.IntroductionThe group III-V compound semiconductors ate important materials used in optoelectronic liquid high speed electronic device. The crystal growth of the III-V compounds can involve processes that require contact between the solid, liquid and vapour phases at near equilibrium condition. Examples of processes that involve contact between the solid, liquid and vapour phases include bulk crystal growth such as the horizontal Bridgman and the liquid encapsulated Czochralski method and liquid epitaxy, and between the solid and vapor include chemical vapour deposition and molecular beam epitaxy. Therefore, the knowledge of the phase diagram and thermodynamic properties for the III-V binary alloys is essential for the analyses of crystal growth techniques of III-V compounds.For these reasons, a series of different · types calorimetric measurements had been carried out: (1) The heat contents of alloys for the Ga-As, In-As, Ga-P and In-P systems by a drop calorimeter [1;2,3]; (2) the heats of formation of the GaAs, InAs, GaP and InP compounds by a twin solution calorimeter [4]; and (3) the standard entropy of these compounds by an adiabatic calorimeter [5]. Based on the third law method, the Gibbs energies of these compounds were derived from the heat capacity, standard heat of formation and standard entropy data obtained by authors. Integral molar thermodynamic quantities of the liquid III-V .alloys were also determined from combining the heat contents of alloys with standard heat of formation and standard entropy data of the compounds· by applying the thermodynamic analysis method developed by Oelsen [6]. In the present study, the thermodynamic calculations for the crystal growth processes of the III-V compound were carried out using newly experimental data of the phase diagram and thermodynamic .properties measured by authors"

Jan 1, 2000

By Tiffany Brown

In the thiosulfate gold leaching process, thiosulfate is used to complex gold following electrocatalytic oxidation of the native metal by Cu(II)-ammines. Unfortunately, Cu(II) complexes also catalyse the undesirable conversion of thiosulfate to polythionates. We have been seeking alternatives to ammonia, which fulfil the role of ammonia but minimize thiosulfate decomposition. One aspect of these studies has involved the determination of the rate of thiosulfate oxidation by the Cu(II) complexes from UV-Visible spectral changes. Various ligand classes, including pyridyls, polyamines, aminocarboxylates and picolinates, have been tested and the majority found to inhibit thiosulfate decomposition. Interesting variations in reactivity with the nature and denticity of the ligand and L/M ratio have been observed. In the case of open chain polyamine ligands with 2 to 5 nitrogen donors, the rate of thiosulfate oxidation was generally found to decrease with the denticity and the concentration of each ligand. Saturation of the Cu(II) coordination sphere appears to inhibit the oxidation of thiosulfate when excess thiosulfate is present. The Cu(II) complex of the branched polyamine ligand, tris(2-aminoethyl)amine (tren) exhibits this behaviour in excess thiosulfate. Interestingly, when the [Cu(tren)(OH2)]2+ complex is in excess oxidation of thiosulfate was observed. This unexpected finding prompted a spectrophotometric study of this reaction which has revealed that the oxidation of thiosulfate involves several processes, two of which involve the formation and decay of a tetrathionate radical.

Jan 1, 2003

By Adolf Mikula

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of ternary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth, silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe element.

Jan 1, 2003

By J. E. Klein

Bench scale tests using a stack of ten whole SAES St909 pellets, 6 grams, to crack methane have been completed with pure methane feed. Test conditions ranged from 600 to 800°C at 101 kPa (760 ton) with a methane feed rate of ten sccm. Methane reformation tests, test where hydrogen was passed through a St909 bed after cracking methane, were performed to determine if and how much methane can be generated under "reformation" conditions. Phase structure determinations of St909, composed of a ZrMnFe alloy with aluminum used as a pellet binder, after methane cracking were complicated by the number of materials that can be formed by the elements in the St909 and the carbon from methane cracking. It was determined that the aluminum not only alloys with the Zr, Mn, and Fe in the St909 alloy, but also forms aluminum transition metal carbides in addition to ZrC as the carbon content and the temperature of the St909 increases. Some A14C3 was also found in some pellets. Passing hydrogen over St909 pellets after methane cracking formed methane at various rates in the temperature range of 600 to 800°C. Temperatures of 800°C gave the best methane cracking performance and efficiencies decreased rapidly with temperature.

Jan 1, 2002

By Y. A. Chang, L. M. Pike, C. R. Kao

"Knowledge of the site preference of ternary solute additions is essential to developing an understanding of how these solutes affect the properties of B2 intermetallic compounds. A quasichemical model will be presented which is able to predict the site preferences of dilute solute additions to tliple defect B2 compounds. The only parameters required are enthalpies of formation at the stoichiometric composition. General equations are developed which can be used to determine site occupations and defect concentrations for dilute as well as non-dilute solute additions. These equations use atom pair bond enthalpies as the parameters. It is found that the site preferences of dilute additions are not always in agreement with predictions based on the solubility lobes in ternary Gibbs isothelms. Predictions for dilute additions to NiAl and FeAl are compared to expel1mental results found in the literature. Satisfactory correlation is found between the model and the experimental results. In addition, the predictions from the model on vacancy concentrations in Fe doped NiAl are compared to recent experimental results by the authors.1.0 IntroductionIntennetallic compounds with the B2 crystal structure such as NiAl and FeAl have been investigated recently for possible use as structural materials in high temperature, oxidizing, and/or corrosive environments. The major limiting property of these materials has been a lack of sufficient room temperature ductility. Attempts to improve the ductility have often been made through ternary or higher order alloying. For B2 compounds, substitutional alloying additions can occupy either of the two sublattices and this site occupancy can be crucial in determining how the alloying addition affects the properties of the alloy. In this manuscript we will discuss the use of thelmodynamic modeling to predict the site occupancies of ternary alloying additions in B2 compounds with the triple defect structure."

Jan 1, 1996

By Adegbenjo Adewale Oladapo, Ibitoye Simeon Ademola, Ladiipo Olufemi Akinbiyi, Adegbola Adekunle Amos, Adeboje Taiwo Bode, Raji Fatai Olasunkanmi

The combined effects of the addition of Silicon (Si) as alloying element and low temperature annealing on the tensile properties of 70/30 brass with Nickel (Ni) and Iron (Fe) contaminants is investigated in this paper. Melts of cartridge brass were made to which 0, 0.5, 1, 2, 3 and 4 wt % of Si was added. These were sand cast into rods of 600 mm by 10 mm diameter and were thereafter machined into standard tensile test samples. Some of these samples were annealed in a muffle furnace at temperatures of 250, 300, 350, 400 and 450 oC respectively and the others were used as control. Subsequently, all the heat treated and non heat treated samples were subjected to tensile tests on a Hounsfield Extensometer and the load – extension plots retrieved were analyzed. Microstructural characterizations of the samples were carried out using Accu-Scope Optical Microscope. The results showed that cartridge brasses subjected to alloying and annealing treatments had improved tensile and yield strengths. However, the tensile properties were increased and maintained within acceptable limits at stress relieve annealing temperatures.

Jan 1, 2015

By Kenneth N. Ham

Hydrometallurgy covers a wide spectrum of areas and its knowledge base is enlarged and enhanced by contributions from many other fields. Dissolution of metals and alloys in aqueous media will be used to illustrate how rich the field of metal extraction can be. Comprehensive understanding of the fundamentals of metal and alloy dissolution in aqueous systems requires creative application of thermodynamic principles, solutions chemistry, ligand complexation theory, electrochemistry, transport phenomena and heterogeneous kinetics. In addition, recent developments in instrumentation in the fields of interfacial phenomena and corrosion have tremendously advanced the field of metal extraction in aqueous system. The close relationship between metal extraction in aqueous systems and various physicochemical phenomena occurring in corrosion and interfacial systems will be discussed and illustrated with examples.

Jan 1, 2002

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras

Viscosity is one of the important physiochemical properties of metallurgical slags which is important for slag tapping, metal loss in slag, freeze lining and fluid dynamics. High temperature viscosity measurements are time- and cost-consuming and the number of experiments is limited. Viscosity model is an effective way to predict the viscosities of the complex slags at high temperature. However, a reliable viscosity model can only be developed on the base of accurate experimental data. A unique high-temperature viscosity measurement apparatus developed at The University of Queensland enabled accurate viscosity data to be measured for the “FeO”-SiO2-CaO-MgO-Al2O3 system in equilibrium with Fe. An accurate viscosity model has been developed based on Eyring’s theory and extensive viscosity measurements. The viscosities of copper smelting, converting and cleaning slags over a wide range of compositions and temperatures can be predicted and applied in the process control.

Jan 1, 2016

By Anand Kumar, Pradeep kumar Jha, Suman Kant, Pradeep Kumar

"It has been a major challenge to reduce the intermixed grade formation during ladle change-over operation in continuous casting process of tundish steelmaking. The F-curve generated by step input of the tracer (new grade steel) tells about the intermixed grade amount for different grade specifications. Use of flow modifiers is beneficial in reducing the intermixed grade because of the change in slope (in different time zones) and position of the F-curve due to their placement at tundish bottom. Present study aims at investigating the role of dam placed before the outlet in a multi-strand tundish with reference to the slope behavior of F-curve in different time zones during the teeming operation plays an important role in determining the intermixed amount.Introduction In Continuous casting process, the old grade steel remaining in the tundish (reservoir between ladle and mould) from the old ladle gets mixed with new grade steel from new ladle and leads to intermixed grade which is considered to be of inferior quality. Although formation of intermixed grade is inevitable with the sequential method of casting, its amount can be controlled by changing the flow behavior of steel inside the steel. Intermixing in a slab caster tundish was simulated using 3-D numerical model based on k-å turbulence equation and compared their result with that of water model experiment Yeh and Hwang [1]. Huang and Thomas [2] reported that quantity of residual fluid in tundish affects the composition distribution in the transitional slab and thus the intermixed length. Huang and Thomas [3] developed three sub models to predict mixing in tundish, liquid core of strand and solidification. Thomas [4] developed a one dimensional model to simulate the final composition distributions in slab caster of continuous casting and investigated the effect of process variables on the intermixing. Alizadeh mehdi et al., [5] simulated of the intermixing phenomenon for slab casting for three different sub models. Goldschmidt et al. [6] developed a numerical model that predicted the location of the intermixed steel in a four line round caster. Lan and Khodadadi [7] studied for the transient fluid flow of liquid steel, heat transfer and solidification during the flying tundish change process. Cho and Kim [8] developed a mixing model to predict the outlet concentration of the tundish during grade transition. Most of the work reported in the literature has dealt with intermixing in slab caster tundish. Billet caster units are more often being used by steel industries due to growing demand of billets. The multiple outlets lead to varying degree of intermixing with time owing to their different distance (location) from the inlet. Use of flow modifier to minimize the intermixed amount, however has also not been discussed in detail so far. Further no work has been reported regarding effect of slope of F-curves obtained through different outlets on intermixing. Hence keeping these objectives in mind attempt has been made by authors to analyze the slope of Fcurves after dividing them into three different time zones and the effect of these time zones on intermixing."

Jan 1, 2012

By E. B. Zanelato

The process of casting metals and alloys occurs through the fusion of this metal and its subsequent casting into a mold with the dimensions and geometry close to the final piece. Most foundries use sand casting molds for making you. This work aims to characterize and evaluate the foundry sand to allow its use in segments of Civil Engineering, creating a viable destination for a residue is that discarded. The following characterization tests were performer: particle size, chemical analysis, X-ray Diffraction and Density Real grain. For the execution of the test specimens was used to 1:3 cement and sand, and the incorporation of 10% and 20% of the total mass replacing the sand, and the trace reference. The results show that best results in compression and bending tests were obtained by replacing 10 % of common sand for sand casting.

Jan 1, 2015

By T. Mutoh

Tellurium in raw slime has recently been recovered as copper telluride in Onahama Smelter & Refinery. The slime is decopperized with sulfuric acid solution in conventional leaching tanks. The pregnant leach solution containing 45 g/l of copper and 1 g/l of tellurium is introduced to a copper telluride recovering reactor. The tail solution from the reactor containing less than 20 mg/l of tellurium is recycled directly to circulation tanks of copper electrolysis. The impurities of the product copper telluride is kept below 1% without any purification.

Jan 1, 1990

By Gopalakrishna M. Rao

"Several industrial and government laboratories are of the opinion that solar--cell technology will grow into a billion-dollar industry by the year 2000, especially if oil prices rise again. Of the variety of materials that have been investigated as the major component of photovoltaic systems, silicon appears to have an outstanding advantage. The cost factor is the primary importance in photovoltaic development, since the technology to make silicon cells of acceptable efficiency and life time has existed since the early stage of the space program. Electrometallurgy is one of the low--cost processes for the production of silicon, since it allows direct, single-stage production from some abundant, inexpensive source materials such as silica and fluorosilicates. Among several systems, two are given particular attention, using inorganic baths with Si0 2 or K2SiF6 as the source of silicon respectively. They appear capable of development to commercial production. Conceptual designs of a commercial--scale cell for silicon production at temperatures above its melting point, and of a pilot' plant for plating silicon from an all-fluoride bath are presented. Energy ProspectsThe major changes in the world energy since the first energy crisis in 1970 have impacted on our community. When oil was $40 a barrel in the mid-1970s, we became obsessed with the energy conservation and a search for alternate energies. Even though the crude oil fell below $15 a barrel during the last several years, our energy security fears continue to haunt us. This time it is not the scarcity, but the abundance of foreign oil and the decline in the domestic production.The prospects of energy depends on the demand and supply of energy. These, in turn, depend on future energy prices, which are linked to economic factors, political events, and unforeseen circumstances. Although no one can predict the future with certainty, three energy consumption patterns used by the Ford Foundation are as shown in Fig. 1."

Jan 1, 1988

By Ludwig Hermann

"Phosphorus is required by every cell of living organisms and essential for plant growth. It is a non-renewable resource that must be mined from natural deposits, going gradually into depletion. Abundant secondary resources are available in sewage sludge and meat and bone meal, with the highest exploitable P concentrations in ashes that remain from their widely used combustion with energy recovery. ASH DEC has successfully removed heavy metals and transformed sewage sludge ash into a marketable P fertilizer by application of a thermo-chemical treatment process. Pilot scale investigations in which ash was treated proved that generally heavy metal limits required by fertilizer legislation can be attained. To achieve a high P availability for crops – an essential fertilizer quality feature – was a more challenging R&D task. Our presentation demonstrates the scientific approach and R&D results that lead from assessment of market requirements to licensed products.IntroductionPhosphorus (P) is required by every cell of living organisms. It is one of the major elements for plant nutrition and therefore essential for crop production. P supply in plant nutrition depends entirely on external inputs into soils [1]. This is achieved by P-fertilizers deriving from rock phosphate deposits that are gradually going into depletion. Serious prognoses anticipate that rock phosphate will be the first low running resource in the world [2]. In the EU, last year 2.530 kt of phosphorus (P2O5 in fertilizers) was consumed and only 313 kt (P2O5 in rock phosphate) was mined. Since 2007, rock phosphate prices have increased by 500% because of a tight supply situation [3].For these reasons, P recycling is becoming an increasingly important issue. Suitable secondary raw materials with regard to their high P-content and abundance are sewage sludge and meat and bone meal. In the EU 989 kt P2O5 are accumulated annually in theses materials, of which 632 kt P2O5 are permanently lost to landfills and other forms of disposal. The main reasons for their limited recycling are concerns on heavy metal contents and organic pollutants that may incite health hazards. As an additional shortcoming, the availability of P from these materials to plants is poor and storage and transportation are problematic issues [4, 5]."

Jan 1, 2008

By Tatiana Pereira Moreno, Priscilla Aki Mori de Hanashiro, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Hugo Hashimoto

"Nowadays, End-of-Life (EoL) Liquid Crystal Displays (LCDs) are traditionally disposed in landfills. The increasing access to LCD technology over the last years by Brazilian consumers has intensified LCD' s disposal as an environmental and economic issue. This study aims to characterize used LCDs to identify the main components for recycling. Characterization was performed through scrap disassembly and its components were identified, separated, and weighted. LCDs were disassembled and the following divisions were applied: screen, metal frame, polymeric frame, polymeric sheets and electronic part. Some techniques were used to determine the concentration of Indium in the LCD, the glass/plastic ratio and the different kinds of polymers that compose the screen. The techniques used for characterization included inductively coupled plasma optical emission spectrometry (ICP-OES), Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). This method, when applied to a wide range of LCDs, can allow the development or improvement of an EoL management of LCD.IntroductionWaste Electrical Electronic Equipments (WEEEs) are waste from discarded equipment, such as computers, monitors and cellphones [1]. Over the past years, treatment of WEEE has been emphasized. It occurs due to the technology's advancement that leads to an even larger increase of WEEES [2].Among WEEEs, there are the liquid crystal displays (LCD). LCD technology is applied in cell phones, tablets, computers and monitors. Nowadays, it's the most well known technology when it refers to monitors, due to its advantages over the Cathode Ray Tube (CRT) technology. Some of them are energy saving, smaller size and no radiation emission [3].This feature in the LCD's global market along with the speed at which electronic equipment becomes obsolete affects society economically and ambiently.This issue becomes even more serious when considering the final destination of the liquid crystal displays. LCDs are lead to landfills as other WEEEs. Besides the different materials long degradation time, the environment is damaged by the disposal of the potentially reusable and hazardous materials [ 4]."

Jan 1, 2014

By A. P. Paiva

With the aim of establishing a valuable alternative to the conventional methods, studies regarding the recovery of precious metals by solvent extraction have been increasing over the past few years. In this work, the selectivity of extraction presented by Cyanex 471X toward silver is investigated. Simulated chloride solutions considering contents of iron and copper usually present in actual leaching practice were used. The characterization of the aqueous solutions - in terms of the multiple equilibria established by the chlorocomplexes of the different metals and their relation to the total chloride concentration of the base-electrolyte - was successfully carried out by cyclic voltammetry. The results obtained support the important contribution of the electrochemical techniques for the understanding of the overall extraction phenomena.

Jan 1, 1994

By den Bulck A. Van

In Europe, 50% of the copper originates from recycling. High-Cu containing scraps are regularly rich in impurities like Fe, Ni, Sn and Pb. Many high-Cu containing scraps are fed directly into anode-furnace casting installations or furnaces with limited refining capability. The impurities levels of the anodes produced in these processes should however remain acceptable for further electro-refining. The distribution of Sn between copper and slag has been investigated for conditions relevant to copper converting. Unlike previous studies, this work focuses on the behavior of Sn relevant to fire refining conditions, which are essential for anode refineries.In this study, liquid Cu–1Sn and CuOx–FeOy–SiO2 slag, with CaO additions, were equilibrated at 1300 °C in vacuum sealed SiO2 ampoules. After metal–slag equilibration, the samples were quenched in water. The composition of the slag and Cu metal was investigated with Electron Probe X-ray Microanalysis. The distribution coefficients of Sn between slag and Cu metal were determined as a function of slag composition.

By N. Can

Kinetics and mechanism of the chemical interactions between Si3N4 and TiC were investigated by isothermally reacting samples under nitrogen and argon atmospheres at temperatures between 1600°C and 1700°C? The initial composition of the powder compact contained 20, 30 and 40 volume per cent TiC? Kinetic analysis were performed by measuring mass losses and composition of the titanium carbonitride (TiC1-xNx) at predetermined time intervals? It was found that in the Si3N4-TiC system the degree and rate of the reactions increased with increasing temperature and content of TiC in both nitrogen and argon atmospheres? Si3N4 in the presence of TiC was stable in nitrogen atmosphere and the reactions were confined to Si3N4/TiC and TiC/N2 interfaces? At both interfaces interchange reaction occurs by simultaneous diffusion of nitrogen towards the centre of the particle and desoprtion of carbon in the opposite direction resulting in formation of titanium carbonitrides with various compositions? Reaction products under nitrogen atmosphere were B-SiC, TiCl1-xNx and N2? The maximum "x" value in TiC1-xNx was found to be 0?67 under nitrogen atmosphere? Si3N4 was found to be unstable in argon atmosphere in the presence of TiC and dissociated into liquid silicon and nitrogen gas within approximately four hours of reaction time, depending on temperature? The reaction mechanism in the initial stages of the interaction between Si3N4 and TiC under argon atmosphere proceeds similar to reactions under nitrogen atmosphere? However, considerable amount of Si3N4 dissociates within the first half hour? Liquid silicon aggressively attack both TiC1-xNx and unreacted or partially reacted TiC particles through cracks and pores and diffuses into interier part of the particle forming liquid solutions? After this stage, reactions under argon atmosphere proceeded according to Si-Ti-C ternary system?

Jan 1, 1999

By K. Potluri, S. Akella, S. Bhansali

"This paper presents the design and angular strength analysis of microneedles for use as a transdermal interface for drug delivery, fluid analysis and sampling etc. Microneedles of different dimensions were designed and fabricated using various materials viz. Si02, OxideNitride- Oxide (O-N-0). The design, modeling and analysis was done using the Finite Element Analysis (FEA) software ANSYS™ 6.1. Angular strength analysis of the microneedles was done using angular loading in ANSYS™, with the corresponding inaterial property settings. Using the force-displacement settings, forces of magnitudes in the range of 10 mN - 25 mN were applied on the microneedles at loading angles ranging from 30° to 90° was applied on needles. Square and circular shaped microneedles were modeled and the displacements and stresses generated were studied to characterize the angular strength of the microneedles. The buckling and force-displacement analyses show that O-N-O microneedles are more strong and robust as compared to needles of other materials. The analysis shows that while circular microneedles have uniform stress distribution, square microneedles have low stresses concentrated along the edges.INTRODUCTIONIn modem clinical and biomedical applications, drug delivery is done either by oral administration or by hypodermic injection. Hypodermic injection of drugs using needles is often painful. Hence, transdermal drug delivery techniques are increasingly being sought out as an alternative. In transdermal drug delivery the needles puncture the Stratum comeurn - the outermost layer of the human skin. The advantage of transdermal drug delivery (or transdermal measurement) technique, is that it reduces pain and tissue trauma."

Jan 1, 2004