Search Documents

By S. J. Cook

The subject of capital and the Canadian mining industry is so broad as to be impossible of comprehensive treatment in brief form. The purpose of the present paper therefore will be only to outline in a meagre and somewhat sketchy way the nature and extent of the mineral industry in Canada and to point out those features which are likely to be of general public interest. Canada's mineral industry has a long and creditable production record. The? value of the output per capita rose from $2.23 in 1886 to a maximum of $26.40 in 1920 and the value of the products from ten million dollars in the former year to almost two hundred and twenty-eight million dollars in 1920. Compared with other primary industries and on the basis of the value of production, mining held third place in Canada in 1920, the premier position going to agriculture and the value of forestry production placing that industry second in the list. In the mineral industry, between six and seven thousand properties are operated annually giving employment to up- wards of sixty thousand employees to whom about seventy-five million dollars is paid in salaries and wages. During 1923, seventeen mineral products reached a production value of one million dollars or over in Canada and in order of the values assigned these were: coal, gold, nickel, cement, cop-per, silver, clay products, lead, asbestos, natural gas, stone, zinc, lime, cobalt, sand and gravel, gypsum and salt.

Jan 1, 1924

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By C. -K. Fang, T. H. Chuang

"Temperature effects on the erosion of the 6063 aluminum alloy were investigated. Erosion experiments were performed by sandblasting silicon carbide particles of 80 grit size. The target volume loss, and worn depths of the eroded material were investigated at different temperatures. It was found that the temperature had only a minor impact on the peak attack angle. The effect of temperature on erosion damage depended on the relative humidity (RH) of the environment. IntroductionThe synergy of wind and sand or dust may result in the erosion of materials. However, the severity of erosion damage in different areas and in different seasons might be varied, depending on environmental variables such as temperature and humidity. As a result, determining the effect of environmental variables on erosion damage is important in selecting or ranking materials for their suitable applications in diverse areas.The relationship between erosion wastage and temperature is governed by many factors including temperature dependent properties of the material (strength, ductility, toughness, and dynamic hardness, etc.), mechanical erosion characteristics, the rate of oxidation, and the mechanical properties of oxides. Although the effect of temperature on erosion has been studied for engineering materials (Smeltzer et al., 1970; Gat and Tabakoff, 1978; 1980; Levy et al., 1986; Levy and Man, 1986; Chinnadurai and Bahadur, 1995; Howard and Ball, 1997; Colclough and Yeomans, 1997; Suckling and Allen, 1997), published literature dealing with aluminum alloy is rather limited."

Jan 1, 2000

By A. McLean, J. Hou

Waste slag is a major environmental concern within the metallurgical industry. In the steel industry, about 100 kg of slag is produced in making one tonne of liquid steel from iron in addition to that produced during ironmaking. The amount of slag from the steelmaking converter can be significantly reduced when charging hot metal with low phosphorus and sulphur contents. In this context, hot metal pretreatment is known as an effective means of preparing high quality charge material for the converter thus limiting the generation of residual slag during the steelmaking process. In the aluminum industry, about 2-4 tonnes of slag, including red mud from alumina production and dross from aluminum electrolysis and casting, are generated during the production of one tonne of aluminum. In recent years, reuse of waste slag from the aluminum industry is a topic that is receiving increasing attention. In this paper, the possibilities of using waste slag and by-products from the aluminum industry as a refining flux in the steel industry are discussed. Several successful processes to convert waste materials from the aluminum industry to steel refining fluxes are described. Some theoretical aspects of using calcium aluminate based flux for desulphurization are outlined together with results obtained from laboratory experiments on sulphur removal from hot metal. By intelligent use of waste materials, the disposal of solid waste from the metallurgical industries can be reduced.

Jan 1, 2004

By Shintaro Takamiya, Kazunari Yoshida

"Recently, small sized micro-needles for medical are required more frequently by patients. The biggest reason is that it presents great burden on the patients, due to the size of the needle injection. People need to use a very small needle to lower the pain, but the downfall is that it makes them more expensive due to their complicated manufacturing method. Therefore, we need to fabricate a needle by wire-drawing to decrease its price. Tube-drawing is beneficial for its production value; however, in conventional tube-drawing it is difficult of control the wall thickness of the tube and makes it 1mmor lower in diameter. That is why, we propose fluid-mandrel drawing for new tube drawing. This method allows fabrication of a fine tube by using the pressure of the fluid in the tube. In this research, the goal is the fabrication of a fine tube by fluid-mandrel drawing and its evaluation. Finally, the fabrication of a fine tube by fluid-mandrel drawing was conducted and in result a tube with a diameter of 0.2mm, high strength and thin wall and fine inner surface was drawn, which can be used as a lesser pain micro-needle.INTRODUCTIONThe main manufacturing method of the current medical needles is roll forming. With this method, it is difficult to make a tube with a diameter lower than 1mm. Deep drawing has been proposed and used as method to further reduce the diameter, but this method is costly and the injection needle obtained by this method is several times more expensive.Therefore, we need to obtain a fine medical needle by drawing process that can be mass-produced and inexpensively manufactured. However, with the conventional drawing process, it is not possible to obtain a syringe needle with a reduced diameter easily, that is why, a fluid-mandrel drawing has been proposed which can reduce the diameter without damaging the inner surface. The methodology of the method is, a fluid is filled in the sealed tube and the pressure inside the tube during drawing is responsible for the good inner surface and wall thickness. It is also expected that the fluid can be easily discarded and that the tube can be manufactured on a long scale."

Jan 1, 2017

By V. L. Mitsopoulos

This paper provides a summary of tailings disposal techniques and the improvements that have been made through the introduction of thickened tailings disposal. The general properties and characteristics of thickened tailings are described, as is a design process for selecting appropriate technologies for thickening, pumping, transporting and storing tailings. The factors affecting the selection of an appropriate disposal site and operational considerations for the effective utilisation of tailings storage areas are also documented.

Jan 1, 2006

By Bruce Regensburg

As trucks become larger and larger, haul roads take on a more significant role in mining costs and economics. The School of Mining at the University of Alberta has compiled a design manual for haul roads using both empirical and theoretical information. One section of this manual deals with the economics of haul road construction. While many mines look only at the construction costs of haul roads, this paper looks at all associated parameters including construction costs, removal costs, timing, truck productivity and width implications. The authors demonstrate the method to determine the most appropriate quality of road for different road conditions and life spans.

May 1, 2001

By K. D. Peaslee, J. M. Soto, IéDé Smith, A. D. Saikia

Spinel-forming refractories reduce penetration of metal and slags through a tightening of the lining resulting from the volume expansion associated with spinel formation. Sintered spinel is often added to reduce the overall volume increase that results. Tests were carried out to evaluate the difference between performance in spinel¬forming and spinel-containing refractory mixes. Eight refractory linings, one (1) pure magnesia, three (3) magnesia-base spinel-forming and four (4) alumina-base spinel- containing dry vibratable mixes, were tested for four hours in contact with a low-carbon, low-manganese steel in a coreless induction furnace at temperatures in excess of 1600°C. Afterwards, sample were cut, and wear and penetration were measured. For magnesia-based mixes wear was minimized using 20-30wt. spinel formation although further experiments are required to determine the optimal value. For alumina-based mixes, there seemed to be an optimal ratio of spinel added to spinel formed that minimized penetration and wear at the slag line. Sidewall accretion occurred and the accretion was the highest for the mix with the ratio of spinel formed to spinel added near the optimum value. Therefore to design an optimum refractory mix the benefits of higher ratios of spinel added to reduce penetration and wear at the slag line will need to be balanced with the tendency to form accretions on the sidewalls of the furnace.

Jan 1, 2004

By P. Henry

Hydrometal provides an adequate technology to reintroduce lost metal units into the industrial cycle, thereby saving resources and energy, while keeping the environment cleaner. Two case studies of our integrated hydrometallurgical recycling facility (Hydrométal) in Belgium are discussed.(I) Recycling of Cu-Co cement generated at the second purification step of zinc sulfate solution. (II) Recycling of lead complex materials from the lead industry.

Jan 1, 2008

By R. A. D. Pattrick, D. A. Polya, D. J. Marsh, J. -J. Bao

"Abstract-The utility of high-density stream sediment and stream water sampling to the exploration for silver deposits was investigated by the study of the epithermal Ag-Au base-metal prospect at Lagalochan in western Scotland. The geology of Lagalochan is dominated by a calc-alkaline Caledonian intrusive complex emplaced into Dalradian Supergroup rocks (Harris et al., 1988a). The complex consists of subvolcanic porphyrytic rocks associated with intense hydrothermal alteration and brecciation. Early Cu-Ag-Mo-rich mineralization is found in the core of the complex with later Pb-Zn-Ag-Au-As-Sb-rich mineralization toward the margins (op. cit.).Stream sediment sample analysis spatially resolved the Cu-rich and Ag-rich mineralization. Ag and Cu anomalies relative to local background values were found in all size fractions analyzed (-125 µm, +125 µm, +180 µm, +250 µm) but the more pronounced anomalies were found in the -125 µm fraction. The coarser fractions generally revealed more erratic but longer dispersion trails. The separation of Cu-rich and Ag-rich mineralization is also apparent in the distribution of relatively high dissolved Cu and Ag in stream waters, particular when expressed relative to the solute load as Cu/TDS and Ag/TDS.The mineralization at Lagalochan is indicated by Ag, Cu and Pb stream sediment and water concentrations that are anomalous with respect to local backgrounds, but are difficult to distinguish from regional backgrounds. This emphasizes the further potential of high-density stream water sampling, in particular, as a viable geochemical exploration tool on a sub-regional scale for epithermal deposits in relatively unpolluted upland terranes."

Jan 1, 1995

By Halet. R. A.

"The Quesabe Mine, owned by Brunston Mines Limited, is a gold deposit in the south central part of Duprat Township, northwestern Quebec, about 10 miles northwest of Noranda.It is one of the few gold mines in Canada developed since World War II. The occurrence of gold in the Quesabe fault structure has been known for many years, but serious exploration did not begin until 1945. By 1949, 15,000 feet of diamond drilling had been completed and a shaft sunk to a depth of 635 feet, with lateral development on the 450 and 600 foot levels. In 1949 and 1950 a new shaft was sunk to 1,050 feet, new levels were established at 800 and 1,000 feet, and ore was mined and shipped to the Noranda smelter. After November 1950 the ore mined was treated in the company's own mill. The grade of ore was marginal under existing economic conditions, and production was suspended in April 1952. The mine produced about 100,000 tons of ore with an average grade of approximately 0.25 ounces of gold per ton.GeologyThe bedrock formations are all Precambrian, and the general geology of the area has been described by W. G. Robinson (1). The rocks in the vicinity of the mine are acidic and basic volcanics of the Keewatin series (andesite, rhyolite, agglomerates, tuffs) invaded by the Flavrian Lake granite stock, and by dykes and irregular masses of intrusive felsite, quartz porphyry, syenite-porphyry, diorite, and lamprophyre.The mine workings are in andesite and felsite, about 2,500 feet west of the western margin of the Flavrian Lake stock.The principal structural feature of the area, from an economic point of view, is the Quesabe fault. This steeply-dipping fault cuts all the rock formations of the area, and has been traced for about 11 miles along a strike of north 65 degrees east from Lake Arnoux in the northeast corner of Dasserat Township to Duprat Lake near the east boundary of Duprat Township."

Jan 1, 1949

By DALE MacGREGOR, VERA TUREK

lndusmin Limited acquired the St. Donat quartzite deposit in 1967 to produce high-quality silica for use in the sandblasting and silicon carbide industries. The quartzite, of Grenville age, is highly friable and porous. This is due to numerous small, kaolinite-coated cavities in the quartzite; the cavities were formed through leaching, probably by rising hot solutions.

Jan 1, 1984

By Håkan Schunnesson, Kirsten Holme

"When mining high grade, narrow ore bodies, the mining method often implies a very detailed knowledge of the ore contacts to avoid unacceptable ore loss and waste rock dilution. During the past decade, the use of microprocessor based drill monitoring equipment has become an accepted technique, even for percussive drilling. On the basis of the recorded drill performance, such as penetration rate, torque pressure, thrust etc., a fast evaluation of the lithological sequence of the ore zone can be made. In order to evaluate the potential of percussive drill monitoring to pro-vide detailed information of the geometry of the ore body, the technique was tested in the Viscaria copper mine in Sweden during 1996.To provide understandable information to the mine geologist, great emphasis was placed on the separation between the drilling response generated by variations in rock conditions from variations caused by the operator and the drill system. Due to the complicated geology in Viscaria, the drilling response presented to the geologists was separated in two independent signals, one representing the hardness of the rock and one representing the in homogeneity(fracturing) of the rock. With those signals a good separation between different rock types in the ore horizon was achieved.The experience from the Viscaria copper mine is that drill monitoring not only can be used to locate contacts between rock types, but also to characterize rock conditions and, often, also to specify the exact rock type present. Because it is possible to get the drill monitoring information very quickly it is a valuable complement to diamond drilling for increasing the specific knowledge of the geology and the ore body."

Jan 1, 1997

By F. H. Wheeler

CONSIDERING the nature of this audience, I perhaps, in addressing you on the subject of air transportation as related to the mining industry, should speak with tongue in check or at least with some reservation. I know full well that many of you, veterans in the great mineral development in Canada, are perhaps more conversant with the overall aviation picture than I, for aviation to you has been the means to an end, and in many instances has been part and ?parcel in the success of your particular projects, in the form of the initial means of transport. I feel, however, that we in this room today have somewhat parallel geographic interests - yours in relation to what is in the ground, mine in the air - and also in the forests and in the streams - aviation, hunting, and fishing - things which have occupied my attention practically all my adult years. In the light of what has gone. before, and in view of present developments, I think you will agree with me when I say that I do not think there could be a more intriguing pursuit than playing a hand in rolling back Canada's tremendous northern frontiers, even if, at this stage, we have made but slight impression on the untold opportunities which lie in our wide-spread, undeveloped areas.

Jan 1, 1956

By C. Mawdsley

The Tata Steel mill at Skinningrove in the North East of England produces top hat sections for mineshaft guides in sizes 102 and 150 mm. The top hat section is the technically preferred shaft guide choice for modern deep mine shafts. This paper explores the relative service performance of top hat and square hollow section guides in service. Comparative corrosion performance is reviewed and the paper describes work commissioned by Tata Steel (as Corus) undertaken by Aker Kvaerner Engineering to evaluate relative winding speeds, relative loads and fatigue life in service. The experience of supply to UK Potash mining is discussed and the future view of high capacity hoisting and larger section size market need and availability is assessed.

Aug 1, 2013

By Paul Delottinville, Maynard Hall, Henry Hillier

"An expert system application for supervisory control and optimization of the indurating process at the Iron Ore Company of Canada (IOCC) has been developed and installed in closed-loop. Prior to the installation of the expert system, the indurating machine was rebuilt and the instrumentation revamped. A Foxboro I/A Distributed Control System (DCS) was installed for regulatory control, and a new control strategy configured. The modernization of the regulatory control has resulted in significant improvement in both production rate and product quality. Expert system control was implemented in September 1996. Preliminary indications are that the expert system has further improved the consistency of product quality, enhanced fuel efficiency and increased productivity. The expert system considers both wet and dry sections of the circuit, and its optimization scheme is driven by pellet tumble index and compression strength. Statistical Process Control (SPC) rules were implemented in the expert system as part of the quality analysis and control scheme. The expert system application was developed and delivered using the Comdale Expert Optimizer (CEO), and has been in continuous closed-loop control since its installation. The system development and implementation is described, and preliminary benefits are presented..... IntroductionIn early 1996 the Iron Ore Company of Canada (IOCC) contracted Comdale Technologies of Toronto to develop and implement a real-time expert system for optimizing the indurating pelletizing furnace at our plant location in Labrador City, Newfoundland.The decision to install the expert system has been timely. Like many other resource-based industries in increasingly competitive markets, IOCC recognizes the need to find ways to improve the efficiency of our production process and ensure that product quality is maintained at the highest levels. With the Labrador City plant producing 11 million tons of iron ore pellets annually, implementing the best technology solutions to meet these objectives is critical."

Jan 1, 1998

By J. Cayouette, . Blatter, P. Cousin

The Laronde mill was commissioned in 1988 and has been treating the Laronde Perim ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually. In 2008, the Goldex plant began trucking high wade (35-45 Wt Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold wade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine. Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa)

Jan 1, 2011

By P. A. Distin, Jr. da Silva

The history of commercial processes for zirconium/hafnium production and separation is reviewed. A new technology is then proposed as a potential alternative for zirconium/ hafnium separation in a simpler, cleaner way than achieved with current processes. Primary sources of zirconium always contain small amounts of hafnium that must be removed during production of zirconium metal for nuclear applications. This separation is usually carried out by a solvent extraction process, developed in the 1950s, that selectively extracts hafnium, as a thiocyanate complex, using methyl isobutyl ketone (MIBK). Environmental problems inherent to this process are the high aqueous solubility and low flash point of MIBK, and possible gaseous contaminants formation generated by the decomposition of the thiocyanic complexes in hydrochloric acid medium (H2S, HCN, mercaptan’s formation). The present work shows how these problems could be avoided by using organophosphorous extractants that were unavailable when the MIBK process was developed.

Jan 1, 1998

By Shichang Liu, Hongli Jia, Zhaolian Wang, Maotang Liu, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce and promote a latest technology and equipment for magnetite. It’s featured of purifying concentrate, lowering tailing grade, high concentrate recovery rate and stable operation. HUATE® New Style Elutriation Electromagnetic Separator is an equipment to obviously upgrade magnetite. The slurry is fed into separation area through feeder. Generated by excitation coil, the working magnetic field distributes specially in separation area. Under the combined effect of the background field, excitation and demagnetic field and gravity, the mineral particles float downwards in the form of magnetic chains, and interact with the rising water. The gangue, non-magnetic particles, lean intergrowth,etc will be discarded as tailing via overflow tank and pipe. While the magnetic will be discharged from concentrate pipe. Its grade is 2%-10% higher than that of traditional magnetic separation equipment. It adopts the technologies of transformer oil cooling, alternative and uniform pulsation magnetic field controlling the tailing grade, larger drum feed-in device, more uniform umbrella scattering discharge and stabler output current, and realizes lower coil temperature raise, stabler magnetic field, more uniform discharge, effective isolation of weak-magnetic area from non-magnetic area, more obvious upgradation and recovery rate and lowering tailing mFe%. It’s more suitable to purify and thicken the high grade and ultrafine iron powder. Compared with traditional elutriation equipment, it adopts new technologies in removing impurities, operation, large-scale, process simplification, water-saving, remote control, etc. It optimizes the comprehensive beneficiation index, expands its application scope, reduces resource wastes and increases economic benefits.INTRODUCTIONMagnetite accounts for a comparatively great proportion in various iron resources. As it’s a kind of strong magnetic mineral, we must adopt the weak magnetic separation equipment in magnetic separation process to realize removing Si and lowering impurities. While it cannot do very well to use the common weak magnetic separation equipment in the final cleaning to remove Si and lower impurities. At present, the plants, adopting single magnetic separation process to realize cleaning and removing Si and lowering impurities, are in the minority. Most magnetite plants adopt the flotation separation process to remove Si, lower impurities and purify the concentrate. Though with stable indexes and high Fe recovery rate, the flotation process is very complicated, high-cost and with lots of environmental pollution. If adopting the weak magnetic separation equipment can realize removing Si, lowering impurities and the final cleaning, the magnetic separation process should be the primary choice."

Jan 1, 2016

By Hong-wei Ma

With social development and technological advancement, mine rescue robots used in complex environments have developed as a research hotspot. This paper reviews the progress of research on coal mine rescue robots, and key technologies of rescue robot design are put forward, such as mechanical structure, self-navigation and self-orientation, multi-sensor information fusion, multi-robot cooperation, and wireless communication technology.

Aug 1, 2013