Search Documents

By A. R. Sorta, D. C. Sego

ABSTRACT The settling, shear strength, and index properties of oil sands fines-sand mixture tailings (FSMT) for a wide range of solids and fines content are investigated. Results indicate that the liquid limit of FSMT obeys a linear mixture law. The fines-water ratio (FWR) governs the permeability of composite tailings (CT) and CT with comparable geotechnical behaviour can be produced from the same initial FWR mixtures. A phosphogypsum (PG) dosage > 900 mg/kg does not improve the dewatering behaviour of CT. The undrained shear strength of FSMT at the liquid limit is approximately 2.4 kPa, but is dependent on fines content at the plastic limit.

Jan 1, 2013

By C. S. Lord

"AbstractThe slow progress of conventional geological reconnaissance of the northern Canadian Shield during the past twenty years clearly indicates the need for a radically new field technique. Operation Keewatin, involving the use of helicopters as the traversing vehicles, was planned and executed by the Geological Survey of Canada in response to this requirement.About 57,000 square miles of District of Keewatin, N.W.T., were mapped during the 1952 field season in appropriate detail for publication at 1 inch to 8 miles. The Operation disclosed about 14,100 square miles of Precambrian sedimentary and volcanic rocks ranging in •age from Archaean to Late Proterozoic. About 7,700 square miles of this area are underlain by greenstone. This work was accomplished in a field season of 113 days, including the spring break-up. Routine aerial geological observations were made from two helicopters flying about 300 feet above the ground; these observations were checked by more than 1,700 landings and about an equal number of aerial observations from heights of less than 50 feet. Logistical support was •provided by a Norseman aircraft on skiis or floats. Combined helicopter and Norseman flying time was about 990 hours. More than 1-00 square miles were mapped per helicopter-hour, and about 815 square miles were examined each day that both helicopters operated. The reconnaissance cost about $207,000, or $3.63 per square mile mapped.As a result of this trial use of helicopters there is now available a reasonably proven method whereby an acceptable geological reconnaissance of the barren grounds of the Canadian .Shield within the Districts of Keewatin and Mackenzie might be completed within a decade. Thus, within a few years, it could place at the disposal of the prospecting and mining fraternity data which, by conventional methods, might not be made available to this generation. Due weight must be accorded this time factor when evaluating the aerial technique."

Jan 1, 1953

By E. W. Garner

THE greatest problem confronting business managers in modern times is not production, but distribution. It would be easy to expand productive output, but it is difficult to find markets for all that is produced. The fundamental source of economic difficulty, in the view of many observers, is a lack of proper balance between productive capacity and consumptive capacity. The studies conducted by the Brookings Institution on the general subject, "The Distribution of Income in Relation to Economic Progress", have led to conclusions of far-reaching significance, which may be summarized briefly as follows: (1) We have never lived beyond our economic means or capacity. (2) We have not been suffering from general overproduction. (3) We have not as yet reached a stage in our economic evolution at which it is possible to provide adequate standards of living for everybody. ( 4) It would require less than a 25 per cent increase in purchasing power among the masses to absorb our full productive capacity. (5) Production-curtailment programmes-whatever their merit in meeting temporary maladjustments-can only lead to national impoverishment. (6) Our inability to find markets adequate to absorb the full output of our productive establishments is explained by the unequal distribution of income and consequent restricted flow of purchasing power through consumptive channels. (7) The slow rate of growth of consumptive demand serves to retard the rate at which new capital is constructed, and hence the rate of economic progress. (8) The primary need is a rapidly expanding total income, and a broader diffusion of this income among the masses of the people. (9) A broader diffusion of income can best be achieved by reducing prices as rapidly as increasing efficiency will permit. That is to say, the benefits of technological progress, mass production, and low unit costs must be promptly passed on to consumers in the form of lower prices-giving more for each dollar.

Jan 1, 1936

By M. Peshko, J. C. Gingerich, L. W. Matthews

"Noranda has successfully developed and implemented two leading-edge mineral exploration technologies — hyperspectral remote sensing and 3-D seismic surveying. Airborne hyperspectral imaging provides detailed geological and mineralogical mapping capability at both a regional and project scale that facilitates improved selection of prospective terrain and an accelerated exploration cycle. Noranda, in partnership with Falconbridge, has licensed the exclusive use of the Earth Search Sciences Inc. (ESSI) Probe-1 hyperspectral scanners (128- channel, 0.43 µm to 2.5 µm spectral range) that are capable of mapping in excess of 3500 km2 per day at 10 m pixel resolution. The technology has been successfully deployed on four continents over a broad range of terrain from desert to boreal forest and the high Arctic.To augment the company’s deep search initiatives, Noranda has successfully modified and implemented existing 3-D seismic technology to help targeting massive sulphides located at depths ranging from 500 m to 2000 m. In the fall of 1998 and early 1999, Noranda completed an 18 km2, 3-D seismic program in eastern Canada by successfully drill testing acoustic impedance anomalies locating massive sulphides at depths in excess of 1100 m."

Jan 1, 2002

By G. Danha, S. Wabula, D. Glasser, D. Hildebrandt, N. Hlabangana

"Impact tests on single particles or a bed of particles are used to determine the fracture characteristics of particles. Many different techniques have been adopted in comminution in order to find ways of optimizing energy consumption in the size reduction process. In this paper, we apply one such method called the Attainable Region (AR) analysis technique to optimize the impact energy on a bed of silica particles. The attainable region is a fundamental approach that is equipment-independent and can be used to analyze breakage processes. The AR is defined as a set of all possible outcomes, for the system under consideration that can be achieved using fundamental processes operating within the system.INTRODUCTIONThe energy crisis in Southern African has reached such critical levels, that most cities in countries like Zambia, Zimbabwe, Lesotho, Swaziland and even South Africa are experiencing load shedding challenges lasting sometimes up to 18 hrs a day. Southern Africa is well known for its riches in mineral resources, and the economies of most states in this region are driven by the mining & mineral processing sector. With the emergence of small scale miners due to government empowerment policies, national energy providers have had to resort to power cuts mainly to domestic users in a bid to cope up with the huge industrial electricity demands.It has been estimated that about 4% of the total energy used in the world is consumed by the mineral processing sector (Fuerstenau & Lutch, 1999). Tomanec and Milovanovic (1994) estimated that milling alone accounts for more than 50% of the total power used in mineral processing, but this can rise to as high as 70% for hard or finely dispersed and inter-grown ores. Today, the greatest challenge in mineral processing is how to optimize energy input to the size reduction process (Dey & Das, 2013; Nomura & Tanaka, 2011), where it has been observed that only a small percentage (1.5%) of the total energy input really does the breaking (Khumalo et al., 2008) while the rest is consumed by the equipment concerned and lost to contacts that do not result in breakage. The immediate benefits of focusing research on the optimization of energy in size reduction operations in the mineral processing sector lies in potential savings on industrial electricity usage that may then be directed towards domestic users."

Jan 1, 2016

By Stewart A. Ferguson

Location.-The property consists of eight claims (P-12339 to 12343, 12403 to 12405) in Robb township, adjoining Jamieson township on the west. A mocor road extends twenty-two miles northwest from Timmins to the mine. Acknowledgments.- The field work was done in 1940 and 1943, while the writer was employed by the Ontario Department of Mines. The Metals Reserve Company has made available information regarding the property through Messrs. W. R, Dunbar, of Hollinger Consolidated Gold Mines, and W. C. Ringsleben, of the Metals Control Board, Department of Munitions and Supply.

Jan 1, 1945

By Liguang Wang

The froth phase in flotation has received much less attention than the pulp phase despite the fact that froth stability plays an important role in determining flotation performance. Froth stability is largely determined by the stability of thin foam films, which in turn has a strong correlation with the critical rupture thickness (Hcr) of the films. In the present work, a new approach to predicting the Hcr values of thin foam films in flotation froth phase was proposed and examined. The Hcr values were calculated using an advanced capillary wave model with input parameters being surface tension, film radius, capillary suction pressure, and intersurface force. The intersurface force was estimated by using the Stefan-Reynolds lubrication approximation to fit the measured thinning rates of single foam films formed in a Scheludko ring cell, where the film radii were less than 50 microns and were kept constant during the film-thinning process. A comparison between the predicted and experimental Hcr values was made for the films with the use of sodium chloride as background electrolyte and in the presence of various frothing reagents such as methyl isobutyl carbinol (MIBC), polypropylene glycol with an average molecular weight of 400 (PPG400), and sodium dodecyl sulphate (SDS), at different concentrations and film radii. It was found that the model correctly predicted the trends of Hcr-versus-concentration and Hcr-versus-film radius curves. Moreover, the predicted Hcr values matched well with the experimental ones of the foam films containing either SDS or PPG400. For the foam films containing MIBC, however, the model overpredicted the Hcr values. The reason for this discrepancy was discussed.

Jan 1, 2016

By Daniel J. Corkery

Mines in Canada and the United States are subject to regulations limiting ammonia, nitrate and nitrite levels in mine effluents released into the environment. The primary source of these nitrogen compounds is typically explosive used in blasting operations, as ammonium nitrate (AN) remains a significant component of most explosives used in the mining industry. The amount of AN entering a local water drainage system is related to site conditions, explosives used, explosive handling and blast efficiency. Mining operators acknowledge AN loss to mine water from blasting operations. However, the mechanisms by which ammonia, nitrite and nitrate are entering the water drainage system, or the relative contribution of specific mechanisms, may not necessarily be assessed or monitored adequately. Characterization of these mechanisms, through systematic investigations, allows a mining operation to focus its efforts on reducing AN loss. This paper outlines a strategy for investigating the mechanisms through which AN enters the mine water drainage system and methods to mitigate this loss. This strategy includes collection and analysis of data to identify and quantify the AN loss mechanisms, design and implementation of tests to mitigate this loss, and assessment of the results. Such investigations are not intended to be a separate one-time project, but part of a long-term process of continual feedback and optimization that is related to the collection and reporting of AN levels for regulatory purposes. The implementation of the strategy must be tailored to each mine?s requirements and existing conditions.

Oct 1, 2010

By M. R. Hudec, M. A. Nikolinakou, P. B. Flemings

"We model the shale response to the large deformations associated with salt bodies, and we identify the implications of the stress changes for hydrocarbon exploration. We employ both the static and evolutionary approach, and show that while the static one can model actual geologic geometries, only the evolutionary approach can provide a detailed description of the stress history of shales, which is essential for predicting stress, porosity, and pore pressure and, more generally, for understanding Earth processes related to salt-hydrocarbon systems.INTRODUCTIONDuring the last two decades, understanding the stress, material behavior, and pore pressure in shales around salt bodies has become increasingly important. The energy industry routinely drills near salt (Beltrão, Sombra, Lage, Fagundes Netto, & Henriques, 2009; Meyer, Zarra, Rains, Meltz, & Hall, 2005; Seymour, Rae, Peden, & Ormston, 1993), because a significant number of hydrocarbon reservoirs around the world are found in layers dipping away from salt diapirs.Salt is a viscous material that cannot sustain deviatoric stresses. Under differential loading it flows, changes shape, and eventually relaxes to an isostatic stress state (Urai & Spiers, 2007). Therefore, emplacement of a salt body and its viscous relaxation process may cause significant deformation of the surrounding sediments, perturb their state of stress and create local overpressures (Dusseault, Maury, Sanfilippo, & Santarelli, 2004; Seymour et al., 1993). As a result, drilling near salt is particularly challenging, and problems leading to additional expense or even abandonment are common (Bradley, 1978; Dusseault et al., 2004; Meyer et al., 2005; Seymour et al., 1993; Willson et al., 2003).Historically, salt and the evolution of its cross section to the present day geometry have been studied using kinematic restorations (Rowan & Ratliff, 2012). This approach aims to explain the present geologic section through a sequence of plausible past sections; however, it does not model the constitutive response of the wall rocks, hence it cannot provide any prediction on their state of stress. Similarly, largestrain numerical studies (Albertz & Beaumont, 2010; Chemia, Schmeling, & Koyi, 2009; Goteti, Ings, & Beaumont, 2012; Gradmann, Beaumont, & Albertz, 2009) have focused on the rheological evolution of salt systems without modeling the geomechanical response of the sediments."

Jan 1, 2015

By J. G. Martin, J. C. Campbell

THE VICTORIA JUNCTION 31,4-million-ton coal preparation complex went into operation in October 1976."' It is designed to produce a metallurgical coking coal by lowering the sulphur and ash content of the raw coal using a heavy-media cycloning process to treat deslimed crushed coal, with scavenging of fine coal by flotation from the primary minus-28-mesh screen product. A secondary H-M cyclone scavenges a thermal-grade coal from the primary H-M cyclone tailing.

Jan 1, 1985

By Mark Sherman, M. Dennis, Raj Rajamani

"The two Alumbrera 36ft (10.97m)dia. SAG mills were sized, using the FDW ""Grindpower 'I program, to treat an average of 1852 tph each. This paper describes how modelling of the shell lifter design, using the Millsoft program, identified milling inefficiencies caused by poor charge motion. This explained the ""as built"" circuit's inability to achieve the throughput rates predcted by the circuit's designer. Use of the Millsoft program to design a new, dramatically different lifter configuration, in conjunction with a different approach to variable speed drive utilization, has resulted in an improved charge motion and a 30% increase in hard ore milling rates. The new lifter design has allowed the designer's predicted average throughput rates to be achieved.IntroductionThe Alumbrera project grinding circuit consists of two 36ft dia. X 17ft EGL, 13 500 kW, variable speed, gearless drive SAG mills coupled to four 20ft dia. X 30ft EGL, 6 000 kW fixed speed, gear driven, ball mills. The circuit is configured as two identical grinding aisles, each consisting of one SAG mill and two ball mills. No pebble crushing circuit was installed due to the expected absence of a critical size fraction in the first years of production. However, the grinding circuit layout does incorporate space for a pebble crushing retrofit. At present, only about 5% - 10% of the new mill feed reports as trommel oversize and is recycled back to each SAG mill using a water cannon.The circuit was designed to be ball mill limited and to treat the four major Alumbrera ore types at rates varying between 68 000 tpd, and 89 750 tpd, depending on ore hardness. Average throughput rate, and hence nominal design rate, for the grinding circuit was 80 000 tpd (1 852tph per line at 90% availability)."

Jan 1, 1999

By Y. Miyabayashi, K. Nishikawa, H. Nagai

JX Nippon Mining & Metals Group recovers valuable metals from end-of-life electronic products in an economical and environmentally-benign way, based on technologies that have been acquired in mining, smelting, and refining operations over time. End-of-life electronic products contain halogens and hydrocarbons. When such materials are treated in the copper smelting process, corrosion of equipment and discoloration of sulfuric acid occur. As a countermeasure to these problems, we have developed pretreatment processes that include an incinerator, exhaust gas washing towers, and a defluorination facility. By implementing these improvements, we have been able to treat a large volume of end-of-life electronic products efficiently in the copper smelting process.

Jan 1, 2014

By Troy Boisjoli, Sean Hillacre, Matt Batty

Discovered in 2014, the Arrow Uranium Deposit has undergone rapid development through successive drilling programs informed by geostatistical drill hole spacing studies. An independent third-party geostatistical drill hole spacing study was completed by Clayton V. Deutsch Consultants Inc. in 2017, evaluating the uncertainty of thickness, grade, density, and areal limit of the Arrow Deposit to determine a drill hole spacing suitable for Indicated Mineral Resources. Indicated spacing was defined to be 24 to 32 metres (“m”) to be within 15% of predicted for a nominal quarterly production volume with a probabilistic tolerance between 75 and 90%. The study not only defined the Indicated Mineral Resource resultant from the 2016 drill program, but also provided drill hole targeting criteria for subsequent drill programs aiming to convert Inferred to Indicated Mineral Resources. A subsequent geostatistical drill hole spacing study on the Arrow Deposit was completed by Clayton V. Deutsch with Resource Modeling Solutions in December 2018 to define Measured Mineral Resource spacing in support of the 2019 drill campaign. The study resulted in a drill hole spacing of 9 to 17 m to be within 15% of predicted for monthly and quarterly production volumes using an accepted industry probabilistic tolerance of 90%.

Jan 1, 2020

By K. S. Coley, G. A. Irons, T. Kaneyasu

"It is very important to reveal the lime dissolution mechanism in steelmaking slag, to promote its dissolution without calcium fluoride, which is now almost forbidden for use in most industrialized countries. In this research, the purpose was focused on the development of an experimental method to measure the mutual diffusivity of Ca2+ under the condition of lime dissolution into slag. By forming diffusion couples using a ""vacuum slag aspirating technique"", the method was established. The following mutual diffusivities of Ca2+, in CaO-SiO2-FeO slag systems, imitating oxygen steelmaking slag, were determined using this method:4.1*10-10 m2/s at 1400°C for 27wt.%CaO-53wt.%SiO2-20wt.%FeO slag,4.3* 10-10 m2/s and at 1400°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag, and 1.3*10-10 m2/s at 1250°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag.It was also verified that, if the basicity and ferrite content of the bulk slag are low, then a calcium silicate film forms on the lime surface, and drastically deters the lime dissolution."

Jan 1, 2004

By Michael S. Moats, Prashant Bagri

"In recent years with increasing concerns about energy consumption in hydrometallurgical processing, there is an ongoing attempt to use Catalytic Titanium Anodes (CTAs) for copper electrowinning. For this work, anodes with IrO2 - Ta2O5 coatings were prepared in the laboratory with the same total coating loading but varying the number of layers by changing the speed of withdrawal in dip coating. A second set of CTAs were fabricated on niobium, Ti Grade 1, Ti Grade 7 and Ti Grade 36 metal substrates. All the anodes prepared in the laboratory were characterized using standard electrochemical techniques and subjected to accelerated life testing. It was found that the coating would not adhere to the niobium substrate, the grade of titanium had a minimal to no effect on the life of the anode, and it is observed that as the coating speed slows, there is an increase in the electrochemically active surface area of the coating which seems to directly contribute to an increase in the Tafel slope of the anodes. There was inconclusive evidence on the effect of coating speed on anode lifetime.INTRODUCTIONLarge scale hydrometallurgical extraction of copper has become widely practiced over the last 40+ years. The hydrometallurgical route entails leaching, solvent extraction and electrowinning. With the increasing desire to process refractory sulphides like enargite and chalcopyrite through the hydrometallurgical route, use of hydro-processing of copper is expected to remain high.In conventional electrowinning, copper is deposited on the cathode and an inert anode is used for oxygen evolution. Presently, the most common anode material is rolled lead-calcium-tin and the cathode is 316L stainless steel (Robinson et al., 2013). This lead alloy is fairly inexpensive and is robust, providing lifetimes typically of 4+ years. The main drawbacks of lead alloys are their relatively high oxygen evolution overpotential, the need for cobalt in the electrolyte to reduce their corrosion, the contamination of cathode product by lead, and the generation of harzardous by-products (Hiskey, 1999)."

Jan 1, 2016

By Fathi Habashi

New technology first introduced by Nippon Steel Corporation at Kitakyushu in Japan in 1976 now used at a number of plants in other countries, known as dry quenching of coke, uses nitrogen in a closed circuit to avoid environmental emissions. In addition, heat is recovered in the form of steam, from the red-hot coke. In steel plants oxygen is used extensively and therefore by-product nitrogen from air liquefaction can be effectively utilized in this way.

Jan 1, 2014

By J. Seidel

In 2009 Newmont Mining Corporation’s annual global spend on grinding media reached $94M USD, having doubled in the five years since 2004. The major contributing factor to the spend escalation during this period was unit consumable price, with total media consumption also rising as a function of annual ore tonnes milled. In an effort to better understand and manage the growth of this expenditure a significant supply chain management program was implemented. This was complemented by a series of technical initiatives focussed on grinding media specifications, quality management and the prediction of grinding media wear rate as a function of physical ore characteristics. This paper discusses the methodology and outcomes of these activities.

Jan 1, 2012

By G. Merle, David L. McKay, Elmar Randveer

"THE ENGINEERING AND TECHNICAL SERVICES department is responsible for supplying the following services:1. Administration and co-ordination of the work required for capital projects.2. Engineering, design and drafting services for inplant changes or improvements as requested by the operating• and maintenance departments.3. Rock mechanics.4. Preparation of plans and layouts required for efficient extraction of the ore as mutually agreed with the mine operating departments.5. Mine planning and long-term schedules in co-operation with the mine operating departments.6. Grade control (long term and short term) and the preparation of ore and waste removal schedules to maintain a uniform grade of mill feed. This also includes the calculation of metal reserves and metal production forecasts.7. Surveying, underground and surface.8. Operations research at the mine site.9. Industrial engineering.10. Chemical analyses and assays.11. Instrumentation.12. Environmental control.A staff of approximately 35 supervisors, engineers and scientists, and 80 technicians, supply the foregoing services. Consulting engineering and drafting firms are used to supply specialized services and technical personnel in-house at Timmins to handle overloads on capital projects under the direction of Ecstall engineers.The operating and maintenance departments depend on the engineering department to supply engineering, design and drafting services for any new facilities or for any planned alteration to existing facilities. To do this efficiently requires a high level of communication and co-operation with these departments. This has been a major factor in developing the present organization of the department shown in Figure 63.The organization is predicated on a strong central technical and engineering resource from which personnel can be assigned responsibilities for different projects, and in different areas, as the work load demands. Job satisfaction is very high because of the variety and challenge in the tasks. Additionally, participation in projects with production and maintenance personnel broadens each technical employee's knowledge of operating and maintenance problems."

Jan 1, 1974

By J. Duncan Keppie

"Auriferous quartz veins occupy zones of dilation. Foldgenerated dilation zones are systematically distributed and are dependent upon the folding mechanism. Comparison of natural and theoretical folds indicates that different mechanisms operated in the Halifax and Goldenville formations.In the slates of the Halifax Formation, the folds are of similar type and internal strain is most intense in the limbs. This internal strain is probably accommodated with little or no dilation.In the meta-sandstone and slates of the Goldenville Formation, a combined flexural and tangential longitudinal strain mechanism, modified by pure strain, produced the folds. Tension fissures produced by this mechanism are: (a) saddle 1'eef veins in slate horizons, (b) veins normal to bedding in meta-sandstone layers in the fold hinges,(c) veins along faults in the cores of tight fold hinges and (d) zones of en- échelon veins in slate honzons in the limbs of folds. Because veins in fold hinges (a, b and c above) account for most of the gold production in the Meguma Group, other factors controlling the distribution and size of these veins are summarized below.1. The size of saddle reef veins is controlled by the curvature of the fold hinge. Thus, a Curvature Index greater than 600 degrees indicates a promising prospect, where"

Jan 1, 1976

By G. Cailletaud, I. Guillot, D. Larouche, R. Martinez, D. Massinon

The precipitation of Al2Cu particles in a 319 T7 aluminum alloy has been modeled. A theoretical approach enables the concomitant computation of nucleation, growth and coarsening, based on an implicit scheme using the finite differences. The equation of continuity is discretized in time and space in order to obtain a matricial form. The inversion of a tridiagonal matrix allows us to determine the evolution of the size distribution of Al2Cu particles at t + dt. The fluxes of solute in-between the boundaries, as well as the ones at the boundaries, are computed in order to respect the conservation of the mass of the system. The main results of the model are compared to TEM measurements. Simulations provide quantitative features on the impact of the cooling rate on the size distribution of Al2Cu particles in good agreement with the TEM measurements. This metallurgical model is integrated into FEA software in order to perform mechanical computations. This kind of multiscale approach allows new perspectives to be investigated in the process of designing cylinder heads. It enables a more precise prediction of the microstructure, its evolution as a function of continuous cooling rates and its impact on the integrity of the structure.

Jan 1, 2015