Search Documents

By M. F. Wells

The method used to salvage South Deep?s Main Shaft after it was flooded by an inrush of water at about 450 m below collar on 1 May1996 is described. The individual techniques employed in the salvage were all proven technology, but the combination in which they were applied is considered to be novel. The operation involved the following activities in order of occurrence. ?the dewatering of the shaft with submersible pumps ?the placement of a French drain on the shaft bottom muck pile ?the positioning of large diameter heavy walled draft tubes, and smaller tightening up, grout intrusion and reverse flow pipes ?the casting and curing of a structural concrete plug; the capping of the draft tubes; the intrusion of several thousand tons of cement grout into the aquifer by pressure induced reverse flow ?the sealing of the aquifer ?extensive probe drilling and sealing of the zone around the inrush point with cement and other specialized grouts ?the mining out of the plug and the re-establishment of normal sinking routines.

Jan 1, 1999

Sufficient time has elapsed since the enactment of the amendments to the mining legislation in 1981 to enable an examination to be made of the way in which the licensing system operates in practice. One of the most important decisions in resource management in New Zealand is whether or not rights of access to the resource should be conferred by the Crown upon an appropriate private sector participant. The licensing system is the means for allocating these rights of access. The manner in which the licensing system is administered, therefore, is crucial to natural resource management in New Zealand. What is the mining licensing system in New Zealand designed to achieve? This simple question admits of no easy answer. Is it the identification and development of the mineral resources of New Zealand? Are these objectives tempered by issues of resource conservation and environmental protection? Is a balance to be achieved among these competing factors? Does the legislation contain any priorities? Does the system respond in an ad hoc manner to particular facts and circumstances or does it operate within a more predictable framework? To what extent are decisions made on access to minerals with reference to the development or conservation of other resources? These questions may be summarised in the title to this paper which poses the question whether mining licences are instruments for resource management.

Jan 1, 1988

By P. I. Page

In mineral exploration the place that yields the first significant result is marked and two questions are posed immediately. Where should the next sample be drawn and how big should it be? At present the answers are arbitrary and ad hoc. They depend on personal experience and sentiment?that is hunch. The thought processes involved in reaching the decisions are unsatisfactory and unsatisfying for professionals. This paper proposes guidance on choosing sample spacing and sample size. The guidance is obtained from the grades of the samples. The grades also imply the extent of influence of each sample assay. Thus sampling and assay are integrated. The integration is achieved by changing the unit of value in which assays and grades are expressed and by exposing meanings and functions of grade beyond that of measuring rock value. The proposals are extended to guide comminution of particle size in sample size reduction and to deal with the problem of erratic high assays. Also, elucidation becomes possible of the computation of a reliable figure for average grade as a statistical weighted mean.

Jan 1, 2005

By Teruo Tanabe

The hydrogen-absorbing materials are expected to have the following properties at moderate conditions, (a) a large capacity of hydrogen absorption, (b) the absorption rate of hydrogen is large and (c) hydrogen-absorbed materials can easily desorb hydrogen. Thus the three concepts of capacity, rate and reversibility seem to be indispensable to clarify the mechanism of hydrogen absorption by the materials. In this work, the amount of absorbed hydrogen, the absorption rate and the reversibility of hydrogen absorption- desorption reaction were measured for binary R-M systems (R = Y, La, Ce; M = Co, Ni). These experimental results were discussed by the following three physical properties that were calculated by the extended Hückel method, i.e. the density of states unoccupied by electrons, the cohesive energy and the energy fluctuation. The major results are as follows: (a) the amount of absorbed hydrogen increases with the density of states in the energy range between -9 and -4 eV, (b) the R-M compounds of which energy fluctuations are large show a large value of rate of hydrogen absorption, and (c) when the cohesive energy is large, the compound has a tendency not to easily desorb hydrogen, i.e. its reversibility is poor.

Jan 1, 2006

By G Ma, L Qi, J G. Shellnutt

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Emeishan large igneous province (ELIP) of SW China is host to magmatic Ni–Cu–(PGE) sulfide and Fe–Ti–V oxide deposits which contain economic to subeconomic concentrations of precious and base metals. The formation of a given deposit-type (ie sulfide versus oxide) is thought to be related to the type of parental magma (ie high-Ti versus low-Ti) and the subsequent processes (ie fractional crystallisation and sulfide segregation), which allowed for metal enrichment.We examined the PGE of Baima and Taihe oxide-bearing layered mafic intrusions from the ELIP (Shellnutt, Ma and Qi, in press), and compared them with the nearby Xinjie and Hongge intrusions as well as with the Emeishan flood basalts. The PGE results for the two intrusions are contrasting. The Baima gabbroic rocks are almost PGE-barren (SPGE < 4 ppb) whereas the Taihe gabbroic rocks are variable, but generally much higher in PGE concentrations (SPGE < 2 to ~300 ppb), although the gabbros from both intrusions are enriched in platinum-subgroup PGE (PPGE = Rh, Pt and Pd) relative to iridium-subgroup PGE (IPGE = Os, Ir and Ru). Cu/Zr, Ni/Ir, Y/Pt, Cu/Pd and Ni/Ir systematics suggest that the Baima rocks were derived from a relatively evolved, mafic, S-undersaturated parental magma that was affected by earlier sulfide segregation. In contrast, the Taihe rocks record evidence of both S-saturated and S-undersaturated conditions and that the parental magma was likely emplaced very close to S-saturation. Through comparison of the PGE contents in the Emeishan flood basalts and the Emeishan oxide-bearing intrusions, we provide a self-consistent model for ELIP that the PGE budget in a magma is not strictly controlled by magma series (high-Ti versus low-Ti), but very much by crustal contamination.CITATION:Ma, G, Shellnutt, J G and Qi, L, 2015. Platinum group elements in the Baima and Taihe Fe-Ti oxide-bearing gabbroic intrusions of emeishan large igneous province and problems on propensity of magma series for sulfide- versus oxide-dominated deposit types, in Proceedings PACRIM 2015 Congress, pp 303–310 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

A comparatively new and very promIsmg field for applying cemented tungsten-carbides is in the mining and quarrying industries. The economic advantages of this unique engineering material over the conventional hollow drill steel, or steel detachable bits, have proven so great that the use of "hard metals" promises, in some instances, to revolutionise the drilling of all manner of minerals. Early in the war years the Germans realised the tremendous advantages cemented carbides offered for holing hard rocks, and they proceeded to develop detachable percussion bits to do this work, at the same time evolving fast, comparatively light-hitting driliing machines, especially designed to suit the mechanical properties of the carbide.Here in Australia also, it has appeared that the detachable percussion bit offers the greatest economic benefits to consumers, although the author is well aware that carbide-tipped drill rods have, and may continue to work out satisfactorily in certain mines and quarries.Most drilling equipment at present installed in Australia may be described as being of the heavy hard-hitting variety, so that the designer of an efficient percussion bit has to take special precautions to overcome the problem of fatigue, and to ensure that the inserts are securely mounted in the body with the minimum of internal stress in the carbide.

Jan 1, 1950

By Unknown

Blast Site Security Involves: * Clearing the area * Controlling Access * Warning Signals

Jan 1, 2003

By Youze Xu

The effect of oxalic acid, acetic acid, citric acid and EDTA on extraction of Cr (?) in soils contaminated by chromium- containing slag was investigated using a batch of incubation experiment. The results show that the pH value decreases more obvious with the increase of the amount of organic acid. The amount of Cr (?) extracted increases with increasing the amount of organic acid. When the ratio of organic acids to total Cr was 5:1, citric acid revealed the highest extraction effectiveness, followed by EDTA, oxalic acid and acetic acid, respectively. The amounts of Cr(?) extracted by citric acid, EDTA, oxalic acid and acetic acid increased by 439%, 244%, 215% and 162%.

Jan 1, 2009

By T. Mwanza, B. N. Belford, P. Conradie

"Metix has introduced a three-piece ’deep-cooled’ copper slag tapblock into a six in-line copper matte settling electric furnace. The tapblock was designed without any internal refractory; it relies purely on the development and maintenance of a freeze lining on its hot face and within the tapping channel to protect the copper and promote the integrity of the surrounding endwall refractory lining. In addition, the geometry of the tapblock further supports the sidewall refractories, reduces the impact of funnelling and, therefore, the need for premature rebuilding of the furnace endwall, and facilitates easy removal and replacement of the wear components even under ’hot’ furnace conditions. Eighteen thermocouples embedded in the copper components ensure full resolution of the copper condition, enabling plant personnel to identify wear rates, estimate freeze lining thickness and stability, and schedule replacement of spares and wear components well in advance.At the time of writing the tapblock had been in operation for 6 months with approximately 350 000 t of slag having been tapped through it. Every indication is that the design will limit the need for premature relining of the furnace endwall due to rapid deterioration of the tapblock and its surrounding refractories. IntroductionNonferrous furnaces rely heavily on the maximization of refractory campaign life to increase profitability and reduce planned downtime. In large electric copper slag-cleaning furnaces utilizing insulating linings, campaign lives of six or more years are realistic if consideration is given to each aspect that can degrade the refractory lining during the campaign. An area that is particularly vulnerable is the slag tap-hole and the local surrounding refractory. To avoid premature relining of the furnace walls, every effort should be made to consider not only the tap-hole design itself, but also the selection of the sidewall refractory material and its construction immediately adjacent to the tap-hole, and furthermore the interplay between the tapblock and this adjacent refractory. A holistic approach to the design that considers these interdependent features in the slag tapping area can reduce the incidence of accelerated refractory wear (‘funnelling’), support the surrounding refractories to prevent their collapse, introduce easily replaceable wear components that can be exchanged with the furnace still ‘hot’, and encourage and maintain a stable freeze lining at the refractory hot face that maximizes the tapblock and refractory lifetime."

Jun 1, 2019

The gold concentration profiles which develop inside the activated carbon particles during the adsorption process were measured, so as to obtain additional direct proof of intra-particle mass transfer rate-control and to determine how individual carbon particles in a population vary in their gold uptake behaviour. The observed gold concentration profiles inside the activated carbon particles were typical of situations where an intra-particle mass transfer mechanism is rate-controlling. Gold di-cyanide penetrated the carbon particles with a wave-like front until it was uniformly distributed throughout the particle. This corresponds with the profiles predicted by the film and surface diffusion model. However, the rate with which gold di-cyanide was transported inside the individual carbon particles varied within the population of carbon particles. This variation was characterized by a lognormal distribution in surface diffusivity. Because the estimated variances of these surface diffusivity distributions were small, the dynamic adsorption behaviour of the carbons used in the present study did not deviate significantly from that predicted by a model based on film mass transfer and a single surface diffusivity. Van Deventer (1984, 1985 and 1986a) reported data that could not be adequately described by a model based on film mass transfer and a single surface diffusivity. In this study a model based on film mass transfer and a wide lognormal distribution of surface diffusivity values was applied to his data. It was shown that a population of carbon particles with a wide distribution in surface diffusivity values could offer an alternative explanation to the mechanism proposed by Van Deventer which was based on film mass transfer, with partitioning of the carbon into micro- and macropores with surface diffusion in the macropores and slow mass transfer into the micropores.

Jan 1, 1997

By V. Svalbonas, M. Fresko

The present versions of the Welding Codes, such as BS7608, have long been known to be compatible with hand computations of membrane and bending stress, rather than detailed finite element solutions. However, in the last five years, in the mining industry, this incompatibility has been largely ignored, and the code interpretations have been pushed into the realms of ground welds, residual stresses, and even flaw growth. Such techniques have to be recognized as extrapolations not necessarily sanctioned by the original code documents. The safety of such extrapolations, as they are related to grinding mill fatigue design, is investigated herein.

Jan 1, 2002

By A. C. Halferdahl

The Granby ores may be divided into three groups or classes. The No. I ore is a heavy pyrite, chalcopyrite, pyrrhotite, sulphide carrying some free silica, and calcite. No. 2 ore carries the same general group of sulphides as does No. 1, but in a lesser amount. The gangue is an altered greenstone. No. 3 ore has a smaller amount of sulphides than either of the others. Analyses of these ores is as follows: Cu. Si02 Fe. CaO S. Al 203 MgO No. I. Per Cent. 1.8 17.5 33.0 5.7 34.5 2.3 1.3 No. 2 Per cent. 2. 0 35. 6 23. 9 4. 3 I .5. 0 9. 2 6 .. 0 No. 3, Per cent. 1 . 5 40. 9 21 . 7 3. 0 I 1 . 3 11 . 0 5 . 4 The sulphide minerals in No. 2 and No. 3 ores occur largely in bands in the gangue, and for these portions comparatively coarse grinding serves to release the gangue. Drill cores show a certain dissemination of sulphides in portions of the rock, so that grinding to 5 per cent. + 65 mesh with 65 per cent.-200 mesh liberates the sulphide minerals very completely. The association of the sulphides is fundamental. The pyrite was probably deposited first and was followed by a portion of the chalcopyrite, or these two portions of the sulphide minerals were deposited together.

Jan 1, 1924

The Carol concentrator of the Iron Ore Company of Canada was completed in 1962 and through expansions .has become one of the largest iron ore beneficiation plants in the world with a new feed capacity of 147,000 It (149,350 mt) per day. The Carol ore contains specular hematite and magnetite having a bulk density of 166 lb/cu ft (2660 kg/m3) It is crushed to 7 in. (178 mm) for feeding to autogenous mills for subsequent concentration by Humphrey’s s spirals. Mine ore is loaded into 150 It (152 mt) trucks by 10 cu yd (7.65 m3) shovels and then, at a transfer station, is loaded into side-dump rail cars of 100 It (101.6 mt) capacity. Each train is composed of twenty cars and operates completely automatically as it hauls the ore to the primary crushing station, dumps its loads, and returns to the loading station, a 11.5 mile (18.5 km) round trip. The primary crushing station is composed of two 60 in. by 89 in. gyratories installed in 1962 and 1972. Neither crusher has a grizzly ahead of it. Rail cars are dumped into 300 It (305 mt) pockets which contain splitters for spider protection. What few oversize boulders which do not go through the crushers are drilled and blasted. Liners in the dump pocket and the crushed ore pokcet under the crusher are manganese steel. Both crushers are direct driven by 700 hp (5 15 kw) motors, and the hardness of the ore causes them to pull almost their full power. Crushed ore drops into a 160 It (163 mt) pocket equipped with radioactive level control units for low-intermediate, and high level indications. The low level unit stops and starts the apron feeder, the intermediate unit controls the feeder speed, and a high-level reading stops the car dumping. Apron feeders are 72 in. (1. 82 m) wide and are variable speed from 12 to 52 fpm (3. 7 to 15. 8 mpm). They discharge to 60 in. (1.52 m) wide takeaway belts. Crushing capacity, nominal and maximum for each crusher, is 4, 000 ltph (4. 064 mtph) and 4,600 ltph (4,674 mtph). The crusher eccentric is removed by a conventional cart which travels on removable rails. Mainshaft removal and maintenance is done by 65 and 75/10 ton cranes. Mainshaft replacement requires eight hours, a usual time, but concave replacement requires only sixteen hours, a result of a fine maintenance organization. Mantle relining is done at grade next to a repair track. Zinc is used for backing both mantles and concaves. Both the electrical rooms and the dust collectors are located below grade,

Jan 1, 1978

By Luis Alberto Martinez Tipe

The paper show how the inclusion of the uncertainty of the geology of the orebody into the mine planning and design process can be of great help, for the mine planner, in both assessing and quantifying the existing risk in the key project indicators such as DCF, and ore tonnage. This is achieved by using conditional simulation and Monte Carlo techniques which provide equally probable models of the original orebody model of the deposit. In this fashion, it is possible to assess the sensitivity of the pit design and related long-term production scheduling (cutbacks) to grade uncertainty.

Sep 12, 2005

Reliable and discriminating small, laboratory scale methods of study have been developed and used successfully in the critical evaluation and interpretation of the carbonization characteristics of a wide range of raw and prepared materials, the variable factors in the coking process, and' the mechanical properties of the carbonized products. The simple and highly economic technologies have been successfully and effectively integrated with detailed surface and subsurface geological exploration programmes (particularly in the coalfields of the .Central Bowen Basin of Queensland) as well as with quality and utilization studies of a nUII!ber of representative Australian and Japanese coals. Previously, only the results of comparatively large, laboratory scale studies have provided information reasonably indicative of those to be anticipated hi industrial practice, but these suffer serious disadvantages in terms of economy of material, time and resources; they have been difficult or even impossible to use as an essential part of any normal or comprehensive exploration programme. On the other hand, although previously developed smaller scale laboratory methods derive considerable advantage from their flexibility, amenity to critical control and inherent potential for speed and economy, they have hitherto permitted no effective or direct comparison with the results of industrial practice or full scale assessment. Comprehensive study results achieved through technologies developed recently at the University 'of Sydney demonstrate that carefully controlled small laboratory scale methods of evaluation quite suitable for use in exploration and, other programmes may be used to predict with considerable accuracy and reliability (in some cases exceedingthat of pilot scale study) the principal strength index of one of the established and internationally recognized full sc:ale tests-the Japanese Industrial-Standard Drum Test. It is probable that further study may establish satisfactory correlations with the results of other standard industrial procedures.

Jan 1, 1969

A device is described which is suitable for the automatic sampling of dust in dust laden flue gases. This device, called a Venturi Sampler, consists of two pipes each fitted with a suitably designed venturi.Both pipes are placed in the flue where one acts as an open-ended reference tube and the other as the actual sampling tube.The gas sampling rate is automatically controlled so as to maintain a zero differential pressure between pressure tappings in the two venturi throats. The venturies are so designed that under these conditions the gas velocity in the sampling pipe is always equal to the free gas velocity in the flue-that is isokinetfc sampling conditions are maintained.INTRODUCTIONThere is a constant need in industry for regular and accurate assessments of dust losses, both to assist in improving operating efficiencies in order to minimize losses, and to obtain accurate metallurgical balances. In many cases where sampling is carried out in dust laden gases, the existing sampling methods are both laborious and inaccurate, and often make no provision for changes in flue gas velocity while sampling is in progress.In the majority of cases where a measurement of dust losses in a stack or flue is required, a preliminary velocity survey is made with a pitot tube to establish the gas velocity at each of the points at which samples are to be taken. The sample of gas (and dust) is withdrawn through a tube connected via a flowmeter to an exhausting apparatus. Some means of removing the dust from the gas sample is placed in circuit ahead of the exhausting apparatus. This is often an alundum or paper thimble housed in a gas-tight container.The purpose of the flowmeter is to measure the actual flow of gas during sampling so that the sampling velocity at the inlet to the sampling tube may be calculated, and the flow corrected so that the sampling velocity will agree with...

Jan 1, 1959

By Sie A

After completing a feasibility study in 1987, Niugini Mining Limited (NML) obtained five Gold Mining Leases within PA 632, covering the Mount Victor and Clarkes Ridge gold deposits. Reserves prior to mining were 260 000t at 3.63g/t Au for Mount Victor and 40 000t at 2.8g/t Au for Clarkes Ridge. Ore was mined from the two deposits by NML from November 1987 to January 1990. A total of 645kg of gold and 346kg of silver were produced from 198 000 tonnes of ore pro- cessed. Mining and milling operations ceased in February 1990. Since then, there has been significant progress in rehabilitating and revegetating the site. Plant and workshop facilities have been dismantled and removed from site, exposed parts of the pit have been landscaped and replanted, tailings water has been neutralised and discharged, and the dam filled. All remaining personnel and equipment left the site in November 1990. It is envisaged that the replanted areas will be rapidly revegetated, leaving little evidence of mining. Niugini Mining did not recoup the initial investment for Mount Victor, but the mine produced a positive cash flow and made a significant' financial contribution to the local communities and Papua New Guinea as a Whole.

Jan 1, 1991

By Brian T. Burch, Paul N. Worsey

When fired, submerged Linear Shaped Charges (LSCs) lose all effectiveness in the cutting of steel. Users in underwater applications have reported having to substantially increase the charge size to the point where brute explosive force shears rather than cuts the target.

Jan 1, 2015

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A. G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids, and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue-gases, the circulating fluid bed technique with internal oil combustion at 220°F for the calcining step and a five-stage fluidized bed cooler for heat-recovery from calcines, the process gives an outstanding heat-efficiency. In a first industrial plant for 560 sh. tons/day of alumina heat consumption figures of less than 1·400 B.T.U./lb Al203 g were achieved.

Jan 1, 1972

By I. Jones

Geologists, engineers, technicians and surveyors have successfully utilized technical software in the mining industry for over 30 years. Software for processing survey, geology, mine engineering and planning information make these functions more efficient by automating repetitive tasks and reducing data processing errors. While these systems have been improved incrementally overtime, new systems that represent giant leaps in technology have been introduced to help mining operations increase productivity and reduce costs. However, their widespread use within the industry has left individual companies without a competitive advantage. Additionally, the ability of these applications to provide the productivity improvements required in today’s uncertain market conditions has since peaked. The next wave of technology—integration of independent software applications—is just starting to emerge and will have a significant effect on the productivity of mining operations. To reap the productivity gains required to remain competitive, mining companies must exploit the collective knowledge and experience of every employee in the organization. Integration of independent software application allows companies to leverage information from all activities, enabling staff to make better decisions to improve productivity. This paper outlines the importance of integration as productivity enabler. Key performance indicators, strategic mine planning, resources management and mine-to-mill integration are discussed as processes that enable productivity. The Gemcom Enterprise Mining System (GEMS)is introduced as the industry’s first integrated solution that enables these productive processes. The paper concludes with a comment on the level of change required to realize the benefits of integration.

Jan 1, 2003