Search Documents

By Ann G. Kim

Hydrocarbon gases, primarily methane but also the Ca through Cs paraffins, the Ca and C3 olefins and possibly the C4 and Cs olefins, are byproducts of coal formation. Although it is generally believed that coal formation occurred at temperatures below 200° C, most experimental work on gas formation from coal has been performed at temperatures between 200° and 1,000°C. The objective of this Bureau of Mines experiment was to determine if observable changes in the gases from coal could be produced at temperatures below 200° C in relatively short periods of time. The experiment involved heating coal samples from six coalbeds at constant temperatures and analyzing evolved gases. The composition of the gases at three temperatures was compared. At 35° C, over 99 pet of the gas is methane; at 125° and 150°, methane constitutes approximately half of the hydrocarbon gas. Isobutane and pentane are the predominant higher hydrocarbons at temperatures between 100° and 150° C.

Jan 1, 1974

By J Hartog, V Beehan, D Beeson

Treating an ore blend from five different deposits at Newgold’s Peak Gold Mine (PGM) has always been a challenge due to the inherent variability between each of the orebodies.Operating the processing plant at PGM with a ‘normal’ level of process control and a good operations and metallurgical team has allowed the processing plant to achieve above the name plate design at 102 t/h and recoveries in the order of 92.8 per cent for gold and 88.4 per cent for copper.With a company value and culture of striving for continuous improvement, PGM implemented the Manta Cube® system, an advanced process control system, for the semi-autogenous grinding (SAG) mill, gold leach circuit and tailings thickener over a 12-month period throughout 2012 and 2013.The overall benefits of implementing the Manta Cube® system has led to an increase in mill throughput of at least two per cent, improved SAG mill liner life, a ten per cent decrease in cyanide consumption and a reduction in flocculant of at least 30 per cent with no detriment to the gold and copper recoveries.The entire project had a payback period of less than two months, and the combined benefits resulted in an overall increase in revenue of at least $5 million per annum. This is quite significant for a processing plant the size of PGM.This paper describes the methodology, overall results and economic benefit of applying the Manta Cube® system on-site at Newgold’s PGM.CITATION:Hartog, J, Beehan, V, Karageorgos, J and Beeson, D, 2014. Optimisation of the Peak Gold Mine’s processing plant through advanced process control, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 335–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By C. E. Lesher

THIS paper reports a study of the reactivity of 950°F and 1650°F cokes as measured by relative rates of reduction of iron oxides at temperatures up to 2200°F. Previous work cited shows general acceptance of the theory that reduction by carbon is a gaseous reaction, and that kind and character of carbon as well as particle size have measurable effect on the velocity of reaction. As will be shown, the data obtained in this study confirm those conclusions. The work was not designed to examine iron oxide reduction equilibrium, but if reaction velocity be defined as the speed with which "a reaction tends to approach conditions of equilibrium," the data here presented may be considered as a study of reaction rates, and the relative degree of reduction to metallic iron as the measure of reactivity. Three standardized combinations of Lake Superior brown iron ore with carbon were tested by similar procedures. One combination was a mechanical mixture of carefully sized high-temperature coke (1650°F) with the ore. The second was a mechanical mixture of the ore with Disco* obtained by carbonizing the identical coal at 950 °F. The third was an agglomerate prepared by carbonizing the coal and ore at 950°F, premixed in proportions to give as nearly as possible the same relative amounts of carbon and ore as the mechanical mixtures. This agglomerate, obtained by heating the finely divided ore (through 30 mesh) with coking coal through the plastic temperature range so as to form solid aggregates, gives a product in which the oxide particles are impregnated with, and intimately bound together with low-temperature coke. The agglomerate-—ore-Disco—was most active in oxide reduction; the mechanical mixtures of Disco and ore next in order, with coke the least reactive. General Discussion: Carbon exists in many forms and it is well known that the form or nature of the carbon used in reduction of oxides is related to the critical temperature of reduction. Sugar carbon, charcoal, and lampblack are forms of carbon that will reduce oxides at lower temperatures than high-temperature coke, and coke will, in turn, give a lower critical reduction temperature than graphite. There have been many investigations of this characteristic of carbons. Johnson' reported a difference of 130°F (70°C) in the critical reduction temperature of zinc oxide as between charcoal 1891 °F (1033°C) and Acheson graphite turnings 2021°F (1105°C) with zinc oxide. Bodenstein2 using charcoal and coke, found a difference of 138°F (77°C) comparing an experimental figure of 2066°F (1130°C) for coke and 1928°F (1053°C) for charcoal, in the reduction of zinc oxide. He concluded that this is very marked and observed that the "type of carbon merely raises or lowers the temperature at which rapid reaction takes place." Comparing the effectiveness of types of carbon in reduction of zinc oxide, it was found that a "brown coal coke" gave 97 pct zinc elimination at 1832°F (1000°C), as compared with 48 pct with "hard coal coke."' A wide range of metallic oxides was studied by Tammann and Sworykin,4 who found that the temperature at which decomposition of oxides begins depends on the nature of the carbon used. Carbon in the form of graphite, lampblack, and sugar carbon was investigated. Sugar charcoal will reduce Fe2O3 to Fe3O4 at 842°F (450°C) as compared with 1112°F (600°C) for coke, according to Meyer." Direct reduction of iron oxides by charcoal begins at 1382°F (750°C), but "first becomes intense" at 1652°F (900°C), whereas with coke, direct reduction begins at 1742°F (950°C), and "first becomes appreciable" at 2012°F (1100°C).6 he total reduction of the sample under certain conditions when heated in a current of CO with charcoal was about 100 pct for limonite and about 77 pct for magnetite. Using coke under the same conditions, the respective percentages were 75 and 47. In a study of processes for sponge iron7 by the Bureau of Mines, the conclusion was reached that a low-temperature char from noncoking subbituminous coal is the most satisfactory solid reducing agent. In a critical study of zinc smelting from a theoretical viewpoint Maier8 concluded that the reduction is by CO, that the reaction between ZnO and CO is intrinsically more rapid than the subsequent reduction of CO2 by C, which is limited by diffusion rates, which in part effectively limits the smelting process. Maier said that the operation is improved with the activity of the reducing carbon. An active carbon, he said, is one maintaining a low CO, content in the retort. Reactivity of Carbon: One form of carbon is more potent in reducing oxides than another. A carbon that reacts faster than another at a given temperature is said to be more reactive. Reactivity is measured by several methods, using carbon dioxide, air, or steam as reactants.9 ebastian and Mayers" have developed a method for the determination of absolute reaction rates between coke and oxygen by a study of ignition points under certain conditions. These and other investigators have established the relative reactivity of types of carbon. Lignite, charcoal, bituminous coal, cokes in the ascending order

Jan 1, 1951

By C. E. Lesher

THIS paper reports a study of the reactivity of 950°F and 1650°F cokes as measured by relative rates of reduction of iron oxides at temperatures up to 2200°F. Previous work cited shows general acceptance of the theory that reduction by carbon is a gaseous reaction, and that kind and character of carbon as well as particle size have measurable effect on the velocity of reaction. As will be shown, the data obtained in this study confirm those conclusions. The work was not designed to examine iron oxide reduction equilibrium, but if reaction velocity be defined as the speed with which "a reaction tends to approach conditions of equilibrium," the data here presented may be considered as a study of reaction rates, and the relative degree of reduction to metallic iron as the measure of reactivity. Three standardized combinations of Lake Superior brown iron ore with carbon were tested by similar procedures. One combination was a mechanical mixture of carefully sized high-temperature coke (1650°F) with the ore. The second was a mechanical mixture of the ore with Disco* obtained by carbonizing the identical coal at 950 °F. The third was an agglomerate prepared by carbonizing the coal and ore at 950°F, premixed in proportions to give as nearly as possible the same relative amounts of carbon and ore as the mechanical mixtures. This agglomerate, obtained by heating the finely divided ore (through 30 mesh) with coking coal through the plastic temperature range so as to form solid aggregates, gives a product in which the oxide particles are impregnated with, and intimately bound together with low-temperature coke. The agglomerate-—ore-Disco—was most active in oxide reduction; the mechanical mixtures of Disco and ore next in order, with coke the least reactive. General Discussion: Carbon exists in many forms and it is well known that the form or nature of the carbon used in reduction of oxides is related to the critical temperature of reduction. Sugar carbon, charcoal, and lampblack are forms of carbon that will reduce oxides at lower temperatures than high-temperature coke, and coke will, in turn, give a lower critical reduction temperature than graphite. There have been many investigations of this characteristic of carbons. Johnson' reported a difference of 130°F (70°C) in the critical reduction temperature of zinc oxide as between charcoal 1891 °F (1033°C) and Acheson graphite turnings 2021°F (1105°C) with zinc oxide. Bodenstein2 using charcoal and coke, found a difference of 138°F (77°C) comparing an experimental figure of 2066°F (1130°C) for coke and 1928°F (1053°C) for charcoal, in the reduction of zinc oxide. He concluded that this is very marked and observed that the "type of carbon merely raises or lowers the temperature at which rapid reaction takes place." Comparing the effectiveness of types of carbon in reduction of zinc oxide, it was found that a "brown coal coke" gave 97 pct zinc elimination at 1832°F (1000°C), as compared with 48 pct with "hard coal coke."' A wide range of metallic oxides was studied by Tammann and Sworykin,4 who found that the temperature at which decomposition of oxides begins depends on the nature of the carbon used. Carbon in the form of graphite, lampblack, and sugar carbon was investigated. Sugar charcoal will reduce Fe2O3 to Fe3O4 at 842°F (450°C) as compared with 1112°F (600°C) for coke, according to Meyer." Direct reduction of iron oxides by charcoal begins at 1382°F (750°C), but "first becomes intense" at 1652°F (900°C), whereas with coke, direct reduction begins at 1742°F (950°C), and "first becomes appreciable" at 2012°F (1100°C).6 he total reduction of the sample under certain conditions when heated in a current of CO with charcoal was about 100 pct for limonite and about 77 pct for magnetite. Using coke under the same conditions, the respective percentages were 75 and 47. In a study of processes for sponge iron7 by the Bureau of Mines, the conclusion was reached that a low-temperature char from noncoking subbituminous coal is the most satisfactory solid reducing agent. In a critical study of zinc smelting from a theoretical viewpoint Maier8 concluded that the reduction is by CO, that the reaction between ZnO and CO is intrinsically more rapid than the subsequent reduction of CO2 by C, which is limited by diffusion rates, which in part effectively limits the smelting process. Maier said that the operation is improved with the activity of the reducing carbon. An active carbon, he said, is one maintaining a low CO, content in the retort. Reactivity of Carbon: One form of carbon is more potent in reducing oxides than another. A carbon that reacts faster than another at a given temperature is said to be more reactive. Reactivity is measured by several methods, using carbon dioxide, air, or steam as reactants.9 ebastian and Mayers" have developed a method for the determination of absolute reaction rates between coke and oxygen by a study of ignition points under certain conditions. These and other investigators have established the relative reactivity of types of carbon. Lignite, charcoal, bituminous coal, cokes in the ascending order

Jan 1, 1951

By Norman D. Fitzgerald

The growth of domestic requirements for motor fuel has been phenomenal, rising year after year in a fashion almost unique among commodities, resisting depressions and forging rapidly ahead in times of prosperity. Consumption advanced from 226 millions of barrels in 1925 to 522 millions of barrels in 1938; or 130 per cent. The economic influences generating and sustaining this demand are of vital concern to the petroleum industry. The general factors affecting utilization of motor fuel are well known but it is the purpose of this paper to employ the recently developed technique of economic dynamics to describe them mathematically. Such problems in economic analysis are complicated by the freedom of all the variables to fluctuate, their mutual interdependence, changing incidence upon one another, and the nonquantitative character of some of them. Economic quantities and relationships, unlike those of the physical world, are continuously changing and this dynamic characteristic is both a distinguishing and confusing feature in economic research. The complexities of the problems require application of the analytical devices of mathematical statistics to uncover the probable relationships between factors. The procedure employed is to formulate a logical relationship linking the dependent to the independent variables, and then simultaneously, rather than sequentially, determine their separate effects by multiple correlation. This transformation of common knowledge to quantitative terms makes it possible to measure the probable effects of changing conditions upon requirements, assisting in the sound interpretation of economic policies. The utility of the results of such dynamic analysis is in sharp contrast to the sterility of the trends and other simple empiricisms of descriptive statistics. It is not intended in this study to throw light on the reasons why any motor fuel at all is consumed; but to discover relationships explaining why more was consumed at one time than at another. Specifically the problem is confined to the measurement of the influences of statistically

Jan 1, 1940

By Norman D. Fitzgerald

The growth of domestic requirements for motor fuel has been phenomenal, rising year after year in a fashion almost unique among commodities, resisting depressions and forging rapidly ahead in times of prosperity. Consumption advanced from 226 millions of barrels in 1925 to 522 millions of barrels in 1938; or 130 per cent. The economic influences generating and sustaining this demand are of vital concern to the petroleum industry. The general factors affecting utilization of motor fuel are well known but it is the purpose of this paper to employ the recently developed technique of economic dynamics to describe them mathematically. Such problems in economic analysis are complicated by the freedom of all the variables to fluctuate, their mutual interdependence, changing incidence upon one another, and the nonquantitative character of some of them. Economic quantities and relationships, unlike those of the physical world, are continuously changing and this dynamic characteristic is both a distinguishing and confusing feature in economic research. The complexities of the problems require application of the analytical devices of mathematical statistics to uncover the probable relationships between factors. The procedure employed is to formulate a logical relationship linking the dependent to the independent variables, and then simultaneously, rather than sequentially, determine their separate effects by multiple correlation. This transformation of common knowledge to quantitative terms makes it possible to measure the probable effects of changing conditions upon requirements, assisting in the sound interpretation of economic policies. The utility of the results of such dynamic analysis is in sharp contrast to the sterility of the trends and other simple empiricisms of descriptive statistics. It is not intended in this study to throw light on the reasons why any motor fuel at all is consumed; but to discover relationships explaining why more was consumed at one time than at another. Specifically the problem is confined to the measurement of the influences of statistically

Jan 1, 1940

By T. G. Carnahan

The Bureau of Mines investigated a flotation-nitric acid leach procedure as part of the goal to maximize minerals and metals recovered from primary and secondary domestic resources. Studies were conducted on an ore that contained carbon-bearing and sulfide mineralization that rendered a portion of the ore refractory (resistant) to conventional leaching technology. The procedure investigated for treating the ore consisted of the following: (1) separation by flotation of the carbonaceous and sulfidic components from the ore, (2) leaching the flotation concentrate with nitric acid at 100° to 110° C, (3) leaching the flotation tailings with sulfuric acid, and (4) processing the combined leached slurries in a conventional manner to recover yellow cake. In step 2, HN03 is converted to gaseous products from which it is regenerated by reacting these products with air and water for further leaching. An overall uranium extraction of 96 pct was achieved by this procedure.

Jan 1, 1979

By Samuel G. Lasky

The writer has been interested in determining the mineralogic dis-t,ribut.ion of silver in the base-metal ore of thc Ground Hog mine of the Asarco Mining Co. in the Central mining district of New Mexico.' This ore consists of a varitextured mixture of sphalerite, chalcopyrite, galena and pyrite in a quartz gangue. The average ore contains 14 per cent of zinc, 9.5 per cent of lead, 5 per cent of copper, and 10 oz. of silver per ton. Generally it is accepted that the silver in ores of this type, in which no definite silver minerals can be recognized, is contained in the base-metal minerals. Published assays of pure mineral specimens from many districts show that each of the base-metal minerals contributes in some degree to the total silver content of the ores, and to determine the proportionate amount contributed by each mineral in any specific ore it has been the practice to assay selected specimens of each mineral, the purity of which has been determined microscopically. There being no such assays available for the Ground Hog ore, and it being impracticable to have enough of them made to give average results, the writer resorted to a mathematical attack upon composite assays of large quantities of ore and concentrates. Surprising results were obtained, and it is the threefold purpose of this paper to present these results, to describe the mathematical method used, and to point out the value of using this method even when assays of pure specimens are available. Value of the Mathematical Method The obvious way of attacking the problem would be to separate cleanly large quantities of ore into its component minerals and then to determine the average silver content of each mineral by assay of representative samples. Since an absolutely clean separation is not feasible, it has been the practice, as mentioned above, to assay pure specimens of the different minerals. No one will contend seriously that the silver content of a base-metal mineral is constant throughout any particular deposit, and it will

Jan 1, 1935

By Samuel G. Lasky

The writer has been interested in determining the mineralogic dis-t,ribut.ion of silver in the base-metal ore of thc Ground Hog mine of the Asarco Mining Co. in the Central mining district of New Mexico.' This ore consists of a varitextured mixture of sphalerite, chalcopyrite, galena and pyrite in a quartz gangue. The average ore contains 14 per cent of zinc, 9.5 per cent of lead, 5 per cent of copper, and 10 oz. of silver per ton. Generally it is accepted that the silver in ores of this type, in which no definite silver minerals can be recognized, is contained in the base-metal minerals. Published assays of pure mineral specimens from many districts show that each of the base-metal minerals contributes in some degree to the total silver content of the ores, and to determine the proportionate amount contributed by each mineral in any specific ore it has been the practice to assay selected specimens of each mineral, the purity of which has been determined microscopically. There being no such assays available for the Ground Hog ore, and it being impracticable to have enough of them made to give average results, the writer resorted to a mathematical attack upon composite assays of large quantities of ore and concentrates. Surprising results were obtained, and it is the threefold purpose of this paper to present these results, to describe the mathematical method used, and to point out the value of using this method even when assays of pure specimens are available. Value of the Mathematical Method The obvious way of attacking the problem would be to separate cleanly large quantities of ore into its component minerals and then to determine the average silver content of each mineral by assay of representative samples. Since an absolutely clean separation is not feasible, it has been the practice, as mentioned above, to assay pure specimens of the different minerals. No one will contend seriously that the silver content of a base-metal mineral is constant throughout any particular deposit, and it will

Jan 1, 1935

The writer has been interested in determining the mineralogic dis-t,ribut.ion of silver in the base-metal ore of thc Ground Hog mine of the Asarco Mining Co. in the Central mining district of New Mexico.' This ore consists of a varitextured mixture of sphalerite, chalcopyrite, galena and pyrite in a quartz gangue. The average ore contains 14 per cent of zinc, 9.5 per cent of lead, 5 per cent of copper, and 10 oz. of silver per ton. Generally it is accepted that the silver in ores of this type, in which no definite silver minerals can be recognized, is contained in the base-metal minerals. Published assays of pure mineral specimens from many districts show that each of the base-metal minerals contributes in some degree to the total silver content of the ores, and to determine the proportionate amount contributed by each mineral in any specific ore it has been the practice to assay selected specimens of each mineral, the purity of which has been determined microscopically. There being no such assays available for the Ground Hog ore, and it being impracticable to have enough of them made to give average results, the writer resorted to a mathematical attack upon composite assays of large quantities of ore and concentrates. Surprising results were obtained, and it is the threefold purpose of this paper to present these results, to describe the mathematical method used, and to point out the value of using this method even when assays of pure specimens are available. Value of the Mathematical Method The obvious way of attacking the problem would be to separate cleanly large quantities of ore into its component minerals and then to determine the average silver content of each mineral by assay of representative samples. Since an absolutely clean separation is not feasible, it has been the practice, as mentioned above, to assay pure specimens of the different minerals. No one will contend seriously that the silver content of a base-metal mineral is constant throughout any particular deposit, and it will

Jan 1, 1935

By Samuel G. Lasky

The writer has been interested in determining the mineralogic dis-t,ribut.ion of silver in the base-metal ore of thc Ground Hog mine of the Asarco Mining Co. in the Central mining district of New Mexico.' This ore consists of a varitextured mixture of sphalerite, chalcopyrite, galena and pyrite in a quartz gangue. The average ore contains 14 per cent of zinc, 9.5 per cent of lead, 5 per cent of copper, and 10 oz. of silver per ton. Generally it is accepted that the silver in ores of this type, in which no definite silver minerals can be recognized, is contained in the base-metal minerals. Published assays of pure mineral specimens from many districts show that each of the base-metal minerals contributes in some degree to the total silver content of the ores, and to determine the proportionate amount contributed by each mineral in any specific ore it has been the practice to assay selected specimens of each mineral, the purity of which has been determined microscopically. There being no such assays available for the Ground Hog ore, and it being impracticable to have enough of them made to give average results, the writer resorted to a mathematical attack upon composite assays of large quantities of ore and concentrates. Surprising results were obtained, and it is the threefold purpose of this paper to present these results, to describe the mathematical method used, and to point out the value of using this method even when assays of pure specimens are available. Value of the Mathematical Method The obvious way of attacking the problem would be to separate cleanly large quantities of ore into its component minerals and then to determine the average silver content of each mineral by assay of representative samples. Since an absolutely clean separation is not feasible, it has been the practice, as mentioned above, to assay pure specimens of the different minerals. No one will contend seriously that the silver content of a base-metal mineral is constant throughout any particular deposit, and it will

Jan 1, 1935

By R. G. Ward

The temperature gradient in the subhearth metal or "salamandern of the iron bhst furnace results in the establishment of gradients in the concentrations of silicon, manganese, carbon, and sulfur. The temperature and compositional variations observed in three blast furnaces are analyzed according to irreversible thermodynamics and the systems appear to be close to the steady state condition. Apparent heats of transport, Q, for silicon, manganese, carbon, and sulfur are found to be respectively -17.5, -5, -2.1, and+22k cal per g mol. In conclusion the significance of thermal diffusion in extraction metallurgy is briefly discussed. INCREASING interest has been shown in recent years in the application of irreversible thermodynamics to metallurgical problems. In particular studies have been made of the transport of matter in thermal gradients1-' and under chemical gradients imposed by a binary solvent However, no detailed example in extraction metallurgy has been reported although gradients are the essence of many extractive processes. The case of the distribution of elements in molten blast furnace iron under a thermal gradient is discussed here. DATA In blast furnace operation the hearth bottom is often extensively destroyed by molten metal, and the metal may penetrate perhaps 10 ft into the furnace foundations forming a "bear" or "salamander". Several hundred tons of molten metal may thus exist beneath the level of the conventional tap hole and remain relatively undisturbed for several years under a thermal gradient. This system is subject to little convective stirring because the temperature decreases from top to bottom, and mechanical stirring due to movements in the stack and to tapping operations is unlikely to penetrate far into the metal. The system may thus be regarded as static

Jan 1, 1963

Established as a Division March 24, 1922 John R McMillan, '56, Chairman Claude R Hocott, '55, Past Chairman Thomas C Frick, '56, Vice-Chairman D W Akins, '57, Vice-Chairman Joe B Alford, Executive Secretary 800 Fidelity Union Building Dallas 1, Texas T A Pollard, Treasurer

Jan 1, 1954

By J. J. Jonas, J. L. Uvira

Equipment was constructed which permitted the hot compression of 99.8 pct Armco iron and 2.8 pct Si steel at constant true strain rates of 0.05 to 1 per sec over the temperature range 600" to 1000°C. A maximum true strain of 1.9 could be attained, followed by immediate quenching or by isothermal annealing. True stress-true strain curves were obtained, and the steady-state flout stress, a, strain rate, i, and temperature, T, were found to fit the following expression: The constants A, a, n', and AH were determined for the two ,materials. The activation energies obtained for Arrnco iron and silicon steel are 66 and 80 kcal per mole, respectively, and approximate those for seu- diffusion and for creep. This indicates that hot compression is a diffusion-controlled thermally activated process. THE hot compression of iron and steel is usually carried out in the austenite temperature range,1"7 as this is the one of greatest interest with respect to industrial hot working. However, a disadvantage of testing in the austenite range is that the hot-worked structure is destroyed by the phase transformations taking place during cooling. The present study was therefore carried out in the ferritic temperature range, and the hot-worked substructures were preserved by rapid quenching after deformation. The substructural results will be described in a separate paper, and the present communication is restricted to the strain rate/stress/temperature relationship observed during hot working. The results of hot-compression testing are usually given in the form of true stress/true strain curves, with a different curve for each temperature/strain rate ~ornbination.',~,~ Sometimes simple algebraic equations are fitted to the curves, so that certain extrapolations or interpolations can be performed.1'2'5 These equations are, however, devoid of mechanistic interpretations. The present study was undertaken to show that hot compression can be described by an equation of the type used in creep studies. That is, it will be shown that the temperature dependence of the strain rate in hot working is well-represented by an Arrhenius term, with an activation energy similar to that for creep. Also it will be seen that the stress dependence of the strain rate is similar to that for creep EXPERIMENTAL METHOD AND MATERIALS The investigation was carried out with the following three ferrous materials: 1) Armco iron; 2) Armco iron with 0.26 pct Mn; 3) 2.8 pct Si steel. The first two materials were utilized for investigations performed in the temperature range 600" to 800°C; the last one was used for tests at temperatures from 600" to 1000°C. The materials were of commercial purity,* as shown in Table I. Cylinders of five different sizes were prepared by strain annealing. The resulting mean grain diameter was 3 mm in the 1-in. Armco iron and 2 mm in the other sizes and grades. Different ratios of diameter/height were used to enable the determination of the coefficient of friction. The specimen faces were provided with concentric grooves, which acted as lubricant holders during compression, as recommended by English and ~ackofen' and others.2'9 Powdered glass lubricants were applied to the samples before hot compression to decrease friction and barreling, following the practice of previous investigator~.~~~~~~~~ Different mixtures of glass powder were used for each temperature, after the determination of suitable compositions by experiment.'' Equipment for Hot Compression. Hot-compression tests were carried out on an adapted 150-ton vertical hydraulic extrusion press and also on a modified high-temperature creep machine. The modified extrusion press was used for temperatures up to 800°C. The following items were added to the press: a) a high-temperature furnace with built-in upper and lower platens; and b) a transmission assembly, which permitted the attainment of logarithmically decreasing crosshead speeds. These accessories are described in detail in Ref. 11.

Jan 1, 1969

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation of a coal mine. The average thickness of coal seams mined in the United States has changed very little in the past 40 years. The first measurement of thickness of bituminous coal and lignite seams was made for 1920, when the average thickness was 5.3 feet.2 The average thickness for later years was as follows: 1945, 5.4 feet; 1950, 5.3 feet; 1955, 5.2 feet; 1960, 5.3 feet; and 1965, 5.2 feet.3 Table 1 includes data on number and production of bituminous coal and lignite mines classified by 1-foot intervals of seam thickness mined in 1920, 1945, 1950, 1955, 1960, and 1965. Though bituminous coal and lignite are mined today from seams of exceedingly variable thickness--less than 2 feet to more than 50 feet--a large majority of the production, 62 percent in 1965, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1967

By Paul J. Fopiano

SOME relationships between the flow characteristics of iron single crystals of 99.9 pct purity and the behavior of imperfections have been investigated. X-ray rocking-curve measurements and etch-pit counts were made as a function of plastic strain, and compared to the stress-strain curve obtained on a modified Polyani tensile machine. Crystals grown from rolled strips of vacuum-melted iron by the strain-anneal method1 had a high preference for a (110) longitudinal direction and a (211) face normal. The tensile specimens were prepared from 2 by i by 0.040 in. single crystals having a gage area of 3 by \ in. Rocking-curve measurements were carried out with a highly perfect germanium monochromating crystal in which the dazz spacing was matched to that of the dZl1 in the ir0n.l Well-collimated CuKal radiation was used throughout. These procedures practically eliminated errors due to geometrical and wavelength resolution. Inasmuch as the rocking-curve half breadth may vary markedly from point to point in the specimen being irradiated, the crystals were strained in place by mounting a hydraulic loading device on the double-crystal spectrometer. The rocking curves were taken after each increment of strain in the unloaded condition, since no observable difference was found in the rocking-curves between the loaded and unloaded states. The rocking-curve half breadths of the as-grown specimens were in the range 90 to 120 sec of arc when the beam irradiated an area of about -£ by -& in. on the specimen. DeMarco and weiss3 have shown that, for a well-colli- mated X-ray beam, irradiating about 10"! sq in. of the very same material, half breadths within 10 pct of the Darwin natural half breadth were observed. Since the rocking-curve specimens were stressed by the load-unload technique, the strain achieved at any given stress depended on the time of holding because of low-temperature creep. Fig. 1 shows the rocking-curve half breadth (also area/peak height) as a function of plastic strain for a relatively short holding time (2 to 5 min) at each stress level. For strains less than 0.1 pct the rocking-curve breadth is essentially constant; it is only for larger strains that there occurs a significant increase in this breadth. Where the holding times at each stress level were longer (by well over an order of magnitude) there occurs a significant increase in the rocking-curve breadth only after plastic strains of the order of 0.6 pct had been introduced into the specimen. This observation is related to the time dependence of creep phenomena and emphasizes the difficulty in comparing data obtained by two such different straining methods. Etch-pit results were obtained using a 2 pct nital etch on specimens strained in the range of 0 to 1 pct. Prior to etching, all specimens were annealed for 3 hr at 150°C, the carbon content being sufficient to decorate the dislocations for strains of at least 1 p~t.~ The data points were all taken from parts of the same single crystal which had been strained with short holding times at stress in increments of strain of the order of tenths of 1 pct. The (211) plane is particularly difficult to etch-pit in vacuum-melted iron and therefore it is felt that these values are as much as an order of magnitude low. Fig. 2 shows the etch-pit density as a function of plastic strain. The smooth curve passing through the data points is not meant to infer a quantitative correlation with the rocking-curve data. What is of interest, however, is the change in etch-pit density in the region of 0.2 pct plastic strain. The first three increments in strain (points 2,3, and 4) did not produce a measurable change in the etch-pit density while subsequent increments did produce a measurable change. While the absolute values of these results do not appear to be cor-

Jan 1, 1967

By Gurupraveen Ramanathan

Slot raises are relief holes within a stope in longhole stoping methods, designed to provide a free face that facilitates the expansion of the blasted rock during blasting, ultimately achieving the desired fragmentation. Various methods are employed to produce these slot raises, like conventional drop raise drilling, raisebore & V30 drilling. However, slot drilling is generally characterized by high costs and limitations in precision, resulting in unplanned ore losses and dilution. This paper introduces a novel alternative to slot drilling referred to as the "paste slot", designed specifically for paste backfill operations in underground mining. This new method emphasizes considerations in cured paste strength, paste wall removal, and stope dimensions and employs modified drop raises or dumped rings to optimize blast gas effectiveness and material flow. The paste slot method eliminates the need for reamers and reduces the total slot drill meters an average from 650m to only 300m for narrow stopes (3-4m wide). This significantly reduces the stope cycle time, leading to substantial cost savings and increased productivity. This new method was successfully implemented at the underground mines in Canada and Australia, resulting in a 20% reduction in stope cycle time and cost savings of 53,000 USD per slot compared to the conventional slot. This paper discusses the design and execution strategy of the paste slot method in underground paste backfill operations. It highlights the advantages of the method, shares operational insights gained during implementation, and showcases its potential applicability to other mines across Canada and globally.

Oct 1, 2024

By D. A. Elgillani, S. Atak, D. A. Rice, M. C. Fuerstenau, R. B. Bhappu

Quartz and feldspar cannot be floated with sulfonate at any pH; spodumene floats over a narrow acid pH range, while beryl responds moderately over a broad pH range. After wet-grinding in a steel mill, beryl, quartz, and spodumene float well with sulfonate below about pH 7, whereas the improvement in the response of feldspar is not so marked. A mechanism by which iron can be adsorbed on these minerals is presented. Also, the responses of leached, natural, and wet-ground beryl to amine, sulfonate, and oleate flotation are shown and related to the measured zero-points-of-charge of these materials. Earlier work with leached beryl showed that good flotation could be obtained with alkyl aryl sulfonate over a rather wide pH range using a Fagergren flotation cell.' When a similar response was observed with leached quartz, it was decided that unintentional activation was being obtained from the metallic components of the Fagergren cell. To obviate this difficulty, a microflotation cell was designed, and an experimental technique was devised. These have been described elsewhere. Experiments conducted with the small cell showed that leached quartz could not be floated at any pH with any sulfonate addition,3 which is in agreement with the observations of Kraeber and Boppel.4 Similarly, it was also found that leached beryl responded to sulfonate flotation only over a narrow pH range rather than the broad range reported earlier.1 This early work,1 however, revealed the important effect that wet-grinding in a steel mill has on the flotation response of certain silicates. That is, it was found that quartz and especially beryl floated well over an unusually wide pH range after wet-grinding in a steel mill. Microcline, however, floated poorly below pH 4, even though wet-ground under the same conditions. The work of Eigeles6 on adsorption of oleic acid on leached quartz and iron-contaminated quartz at constant pH is in agreement with these flotation data. Other research has shown that ferric iron, added as a salt to the system, functions as an activator in the narrow pH range in which Fe +++ iron hydrolyzes to its hydroxy complexes.3,5 These phenomena indicate that iron functions differently in flotation systems depending on its method of introduction. The object of this paper is to determine the mechanism by which iron is adsorbed on certain minerals, the mechanism of collector adsorption after iron abstraction, and the role that Fe++ and Fe+++ assume in the selective separation of these minerals. EXPERIMENTAL MATERIALS AND METHODS Sodium alkyl aryl sulfonate, mol wt 450,7 pure potassium oleate, and pure dodecylamine were used as collectors. All other chemicals were reagent grade in quality, i.e., n-amyl alcohol as frother; HC1, H2SO4, and KOH for pH adjustment; and ferric chloride as activator. Conductivity water, made by passing distilled water through an ion exchange column, was used in the experimental work. All minerals used in the investigation were hand-picked specimens. Sample Preparation: Each of the minerals was crushed through 8 mesh, and the product was divided into two groups, one to be ground dry and the other wet. Dry grinding was accomplished with an alumina mortar and pestle. The product was dry-screened to 48 x 150 mesh, cleaned magnetically, deslimed in conductivity water, and dried. Preparation of the samples by wet-grinding involved grinding a 200-g charge of the mineral (-8 mesh) at 60% solids with natural water in a mild steel rod mill for four minutes. This charge was then wet-screened immediately with natural water to 48 x 150 mesh, dried, and cleaned magnetically. Some experiments were also conducted with leached beryl and quartz. These products were prepared by leaching the sized sample (48 x 150 mesh) with concentrated HC1 with a percolation technique until no iron could be detected in the leach liquor. Following this step, the sample was rinsed with conductivity

Jan 1, 1967

By R. L. Montgomery

Electronegativities of the rare-earth elements were calculated from heats of formation. The values obtained from different compounds varied widely. The postulates of Pauling's electronegativity theory were interpreted for bonds that are primarily ionic; the study showed that many compounds obey rules of the form expected. Revised electronegativity values are given for the more electropositive elements, including the rare-earth metals (which are near magnesium in electronegativity). Estimates of un-known heats of formation are made from electronegativities and are compared with other estimates. INTRODUCTION Calculation of the electronegativities of the rare-earth elements is interesting to show how these metals stand relative to the other metals and to each other, and also possibly to systematize the thermochemical data on them.

Jan 1, 1960

By L. V. Pirela, S. M. Farouq Ali

Some interest has been expressed recently in the application of solvents in conjunction with a thermal drive, such as a steamflood. At least one field project of this type has been reported. This paper makes the first attempt to provide some of the basic information necessary for choosing a solvent for such an application. Results of displacements conducted at elevated temperatures are also discussed. This paper shows that, in the case of alcohol-hydrocarbon-water or brine ternary systems, the system miscibility may increase, decrease, or both increase and decrease within the same system when the temperature increases. The distribution coefficient was consistently found to increase in favor of the oleic phase with an increase in temperature, which is advantageous from the standpoint of oil recovery. Results of solvent displacements in a sandstone core showed that even a relatively small temperature effect in the favorable direction (increase in miscibility and distribution coefficient) can lead to a 50 percent increase in oil recovery. On the other hand, if the system miscibility decreases with the temperature, even though the distribution coefficient increases, the oil recovery at the higher temperature may not increase. INTRODUCTION Miscible displacement has been the subject of many investigations. Miscible-phase solvent flooding, employing solvents such as alcohols that are miscible with both oil and water, has received considerable attention. Investigations conducted by Gatlin and Slobod,l Taber, Kamath and Reed,2 Holm and Csaszar,3 and Farouq Ali and Stah14 have helped in understanding the mechanism of solvent flooding. While the use of alcohols and similar solvents as oil recovery agents is economically unattractive, these solvents nevertheless provide a means of understanding the mechanistic aspects of important miscible-phase oil recovery processes such as the Maraflood process (discussed by Gogarty5). As shown by Taber et a1.,2 the phase behavior of a solvent-oil-water system is of .utmost importance in determining the efficiency of the oil displacement. This paper makes the first attempt to obtain the ternary phase behavior data for nine alcohol-hydrocarbon-water/brine systems at elevated temperatures. Results of core tests at elevated temperatures are also presented which corroborate the effect of temperature on oil recovery, as judged on the basis of phase-behavior data. The use of solvents at elevated temperatures has been suggested earlier by Farouq Ali.6 At least one field test of this type has been reportedO7 With the widespread use of thermal recovery techniques, it is possible in some situations (especially in steamflooding) that the use of a suitable solvent in conjunction with the heat carrier may be economically feasible. This paper attempts to provide some of the basic information needed for judging such feasibility. LOCATION OF THE PLAIT POINT The phase behavior of a typical ternary system consisting of a solvent, hydrocarbon and brine (or water) can be represented by a triangular diagram such as the one shown in Fig. 1 (for temperature TI). Point Pon the binodal curve represents the plait point, being the limit of tie lines such as Y1 Y2 The compositions of the coexisting oleic and aqueous phases are given by points Y2 and Y1, respectively, for any mixture composition along Y1Y2. The characteristics of ternary diagrams have been discussed by Findlay8 and others. Taber et aL3 have shown that the position of the plait point in a particular ternary system plays the decisive role in determining whether or not theoleic phase would be displaced in a continuous manner during an alcohol displacement. The area above the binodal curve also is important, since it represents

Jan 1, 1969