Search Documents

By Guillermo Rios, Arbizum Cristina, Joa Viflals, Alba Sunyer

"Atlantic Copper is one of the largest copper producers in Europe. Its production facilities are located in Huelva (Spain) and account for the smelting of over one million tpy of concentrates to produce up to 260 ktpy cathodes and 900 ktpy of sulphuric acid. During copper concentrate smelting, the slag coming from the flash furnace and PS converters are treated in an electrical slag cleaning furnace. As a result of the treatment of the off gases from this furnace, approximately 2,000 tpy of a Zn-rich filter cake are produced and are sent to authorized waste managers. This paper describes the characterization of this material and the preliminary results of a new process to recover zinc as a pure zinc hydroxycarbonate while lead is collected as an indium-rich anglesite product. The behavior of impurities (Cd, As, Tl, Sn, Sb, Bi, Cu, Se, Te) in the leaching, solution purification and precipitation steps is also reported.IntroductionThe Atlantic Copper Metallurgical Complex in Huelva (Spain) was commissioned in 1970 with a capacity of 40,000 tpy of copper from concentrate. In 1975, the old blast furnaces were replaced by Outokumpu flash smelting furnace (FSF) technology, and the copper refinery capacity was increased to 108,000 tpy. Between 1994 and 1996, an expansion project was carried out to increase the copper from concentrate and cathodes to 250,000 tpy and 215,000 tpy, respectively. This expansion basically consisted of a new sulphuric acid plant, replacement of the anode furnaces by two 400 t units, redesign of the slag cleaning furnace (SCF), an increase in the electrolytic cells to 1,120 and implementation of ISA permanent cathode technology. Furthermore, a debottlenecking project has led to a capacity of 1,000,000 tpy of fresh concentrate since 1997. Meanwhile between 1995 and 1998, a cathode production rate of 260,000 tpy was reached as a result of a progressive increase in the current density in the refinery."

Jan 1, 2012

By R. Parada

A real-time dynamic simulation model has been developed to characterise the flash furnace operation at the Chagres smelter. This model permits the operators to plan the process to meet the Peirce Smith converters' schedules and feed the acid plant with gases that satisfy its best operating efficiency range. Essential control parameters for the furnace (process air enrichment, oxygen coefficient and supplementary heat) are calculated to satisfy process targets such as matte grade, slag silica and matte/slag temperatures. These calculations are carried out with a real-time simulation. Flash furnace control and operational stability permits setting up control strategies that streamline the flow of copper to converters and of sulphur to the acid plant.

Jan 1, 1999

The Port Kembla Copper (PKC) copper smelting facilities were commissioned during 2000. Numerous difficulties were encountered during the commissioning such as multiple reactor tuyere line failures, absorbing acid tower refractory collapse, and Noranda Reactor and Mitsubishi Converter process control problems. These problems are described along with the actions taken to overcome them. Process development is described particularly for the Mitsubishi Converter and Acid Plant.

Jan 1, 2002

By Kent D. Peaslee, Lifeng Zhang, Edith Martinez, Yufeng Wang

The current study investigated the multiphase fluid flow, heat transfer, solidification of the steel, and the motion and entrapment of inclusions during the centrifugal casting process using FLUENT software. User-defined functions (UDFs) were developed to add velocity with a value related to the rotation speed and radial distance to the solidified steel, to exert a centrifugal force to the motion of inclusions, and to add the entrapment condition of inclusions at the solidifying shell and export the entrapment locations of the inclusion. The calculation shows that there are two peaks of inclusions along the thickness of the produced tube: one at close to outer surface and another one close to the inner surface of the tube. With a larger rotation speed, inclusions tend to be entrapped more towards the inner surface. The calculation agrees well with the industrial measurements.

Jan 1, 2012

By Petr Stehlík

"This paper is aimed at showing and demonstrating progress in technologies and improvements in units for the thermal processing of various types of waste. The following areas are covered: units for the thermal treatment of hazardous industrial waste and common MSW, technologies for the thermal treatment of industrial and sewage sludge, utilizing waste in cement production (material and energy recovery), up-to-date off-gas cleaning systems, original and unique units for the thermal processing of polluted gases, low-NOx burners. The paper represents a review based on industrial applications, papers published in reputable international journals and a monograph under preparation.IntroductionThe present contribution is an overview of the activities and achievements of the Institute of process and environmental engineering (UPEI) of the Brno University of Technology (VUT). The Institute belongs to European leading teams in the field of the thermal processing of various types of waste. The research in the institute currently revolves mainly around a strategic project “Waste and Biomass Utilization focused on Environment Protection and Energy Generation” that is supported by the national government. Due to the limited space this paper is conceived as a review of papers published especially in reputable international journals.Main (strategic) target of the research is development of new, efficient processes (eventually modernized processes with novel original elements) for effective and highly efficient treatment of waste and biomass, including their maximum utilization as renewable energy sources while minimizing harmful emissions. To this purpose, highly advanced know-how for the design and construction of the related technology lines is being developed, supported by mathematical modeling (see e.g. [1]), experimental validation and optimization.Municipal and Industrial Solid Waste – Concept of Waste-to-Energy CentersThermal processing of various types of wastes is not only waste disposal and/or treatment at present. It has to be regarded as waste to energy process wherever and whenever possible and feasible. This observation was at the origin of the concept of new regional Waste-to-Energy Centers (WTEC), outlined in the following paragraphs. The proposal of the centers is based on a combination of experience, know-how and sophisticated approach. The main fact influencing the concept of WTEC is the necessity to treat different types of wastes. Typical types of wastes as well as main products of the processes in a WTEC are shown in Figure 1."

Jan 1, 2008

By T. W. Gonzales

The BHP San Manuel Smelter operates an Outokumpu Oy flash furnace, conventional Peirce-Smith converters, anode casting facilities, and two double contact sulfuric acid plants. The flash furnace was commissioned in July 1988 and since then, the smelting capacity has been continuously increased to 30% above design. The converter operation was challenged to process larger amounts of matte with existing capacity. Utilization of industrial technological improvements and people technology transformed the Converter Department from a constraint to easily accommodate the new demonstrated flash furnace capacity. This technology also increased secondary consumption, converter campaign life, and reduced operating costs. This paper will describe the important Converter Department achievements in the past five years.

Jan 1, 1999

By Jean Igor Margem., Lucas Barbosa de Souza Martins, Frederico Muylaert Margem, Sergio Neves Monteiro, Artur Camposo Pereira, Rômulo Leite Loiola

"The fibers extracted from the stem of the bamboo plant have been investigated as possible reinforcement composites due to their relatively high tensile strength. Although previous works have already been conducted about the mechanical properties, up to now a dimensional characterization of the distribution and the effect of diameter on the elastic modulus of bamboo fiber of the specimen dendrocalmus giganteus has not been performed. The aim of the present work was to statistically characterize the distribution of the diameter of a lot of bamboo fibers of that specimen. Based on this characterization, diameter intervals were set and the dependence of the Elastic Modulus (E) of theses fibers with a corresponding diameter was analyzed by the Weibull Method. The results indicated an inverse dependence, in which the highest Elastic Modulus were obtained for the thinnest fibers. Moreover, it was found that a mathematical hyperbolic relationship fit well this inverse correlation between the Elastic Modulus and the bamboo fibers diameters.IntroductionBamboo is a well known grass-type plant with a hard and stiff stem or culm that can reach, in some species, more than 10 cm in cross section diameter and stand several meters height. Owing to its low density, approximately 0.9 g/cm3, bamboo culms have been used in house construction from scaffoldings to panels. As an abundant natural resource in tropical and temperate regions, specially in Asia and South America, bamboo is also a substitute for wood and plastics in furniture and lightweight parts of automobile [1,2]. The cylindrical shape of the culm is, however, a limitation for its direct use in engineering systems. Consequently, research works have been conducted on bamboo fibers stripped off from the culm as reinforcement of polymer composites. [1-12]. According to Shin et al [3] bamboo fiber-epoxy laminates can be made into specific sizes and shapes, preserving the natural microstructural properties. These fiber composites overcome the limitation of the culm's cylindrical macrostructure. As a further advantage, Shin et al [3] indicated that cracking and bioerosion caused by insect pests is prevented."

Jan 1, 2013

By Dirk Bergmann

During the spray forming process, a continuous molten metal stream is atomized by impinging high speed inert gas jets. In the generated spray cone, the resulting metal droplets are rapidly cooled by the huge temperature difference to the surrounding gas phase and thereby partly solidified during flight. After a certain flight and residence time inside the spray cone, the droplets impinge onto the solid substrate and form the product (deposit) by compaction. Material properties of this preform strongly depend on several process parameters and especially on the thermal and kinetic state of the deposited droplets at the point of impingement. Smaller droplets may cool very fast due to their low mass and impinge onto the product in a completely solidified state as solid metal powder particles. Larger droplets with big mass contain a higher amount of thermal energy and impact during the state of phase change or still as completely liquid. It is obvious, that a certain amount of liquid content in the droplets is needed for forming a homogeneous deposit. Therefore, the thermal history of metal droplets during flight in the spray cone is of great importance for overall process modelling and control. Modelling the effects of the impinging droplet mass on the formation and heat balance of the deposit, the thermal conditions of the droplet stream need to be temporary and spatially averaged at different locations. Averaging may be achieved in different ways, giving alternative results. A first method is averaging over the droplets total enthalpy which consists of the thermal content and the remaining latent heat of fusion within the droplets. A second method may yield the average over the heat content and the solid fraction separately. Results of these two methods depend on the application and the kind of information which one wants to achieve and show some deviations, which will be discussed in terms of consolidation and energy conservation of the deposit.

Jan 1, 1999

By Michael Heximer, Dominic Verfielst, Timothy Moore

"Teck's Trail Operations recently installed new pressure filters in the cold stage purification step in the zinc leaching plant. Alloy 2205 duplex stainless steel was chosen as the material of construction as it was in use in the hot stage purification operation. Within a year of commissioning, an unacceptably high rate (greater than 1 mm/y) of corrosion was observed on the weld heat affected zone (HAZ). Laboratory and field tests were conducted to establish the conditions under which the corrosion was occurring. The tests isolated the aggressive conditions to a unique combination of materials present during the filter regeneration stage. Furthermore, the change of the duplex grain structure of the alloy during welding resulted in the HAZ being more susceptible to the corrosive environment. A new material of construction was recommended as a result of the investigation.IntroductionThe sulphide leaching plant uses four horizontal tank pressure leaf filters to remove solids precipitated in the cold stage electrolyte purification process. The current filters were installed in 2007, and replaced a bank of filter presses. The material of construction for the filters - alloy 2205 duplex stainless steel - was selected based on its successful use in similar service areas of the leaching plant. However, within the first year, unexpected and rapid corrosion of the filter tank material was observed. Although moderate general corrosion was noted throughout the filters, the attack was particularly aggressive in the areas where intense heat was applied during fabrication, observed at the HAZs caused by welding, and on the exposed edge grain of the duplex plates. On the inaugural annual inspection of the filters in the first year of operation, a corrosion penetration rate of 1.0 to 1.5 mm/y was observed at the HAZs. The parent plate of the pressure tank was a minimum of 6 mm, with a minimum allowable thickness of 3 mm under the ASME pressure tank design rules. Therefore, the projected useful life of the filters could then be roughly calculated to be two to three years. Urgent action was required to understand and correct this problem."

Jan 1, 2012

By Morimasa Ichida

One of the key factors of stabilized blast furnace operation under the conditions of high productivity and high pulverized coal rate is to enlarge the raceway to reduce the dead man area. With a reduced dead man area, the descent area is enlarged and the central gas flow is maintained at the same time. In this study, raceway furnace experiments were conducted with tuyere velocity and coke strength changed both in hot and cold conditions to measure the coke degradation rate. Using the coke degradation rate measurements, we examined the equivalent relation between the coke strength and tuyere velocity for coke degradation in the raceway. In addition, in this paper, we discuss the increase in tuyere velocity in relation to an increase in coke strength.

Jan 1, 2006

By F. A. Myzenkov

The technology developed by the authors uses new methods for raw material smelting in electric furnaces, a new autogenous method and apparatus for subliming smelting for antimony trioxide production and separation of antimony and gold. Concentrate produced from the ore deposits in Yakutia has the following average contents of main constituents, % by weight: 29.4 Sb, 1.2 Fe, 13.1 S, 40.0 SiO2, 0.2 As, 2.6 CaO and 45 g/t of Au. Unlike the technology used abroad a new autogenous method makes it possible to increase considerably specific capacity and reduce gold losses with antimony trioxide by several times. At the same time mineralogical composition of trioxide has improved considerably ? it has mainly a cubic base with prevalence of senarmontite. The content of a main component (Sb2O3) in the final product has increased from 99.0% up to 99.6% which means better quality and makes it suitable for use in special technologies. Despite a lower antimony content of the concentrate (29.4% as compared with over 33% as common in the world practice), an antimony recovery of 85.3% into a commercial-grade product has been achieved, as well as a gold recovery of 96.65% into a gold-antimony alloy. The technology for processing gold-antimony materials developed and introduced at the Ryaztsvetmet plant is unique in the world with respect to gold recoveries.

Jan 1, 2006

By Fatbardha Osmani, Skender Osmani

"A system analysis of the resource and environment management (water, energy etc) starts from its definition. Unfortunately, there is not a unique semantics of the mentioned concept. On these circumstances, in this paper the following issues are presented: 1.A short view on the existing concepts of management. 2.A new definition on the concept of management. It is considered as a complex and rational activity on human and natural resources ,environment etc, which starts from a analysis of infrastructure ,technology , etc, mission , alternatives , project etc. and ends to an optimal output. Basing on this definition, the management has two principal components: strategy and policy. The strategy is referred as a blue print program (the same definition as in Game Theory), which contains all the contingency alternatives. , while the policy is referred as a strategy applied into practice. The strategy is the first , while the policy is the second one. The best alternative of a policy is the project, Each strategy has one and only one project. The mentioned definition erases the differences between concept of policy and politics. Each strategy has its alternatives ,the next has its sub strategy and so on, i.e. whatever are going to be the strategy, there are a hierarchy composed by sub strategies up to the simplest strategies applied by a single individual (human beings or robots). The strategy objectives are necessary and sufficient conditions for its realization i.e . the strategy is an optimal activity, in which all resources are integrated and processed . Several strategies could be joined into one( for example the surface water strategies of the Balkan countries) . In this view, the strategy could be globalized into optimal way basing on different criteria’s as social, economic, environmental, their risks and effectiveness etc. etc An example from the water management illustrates the mentioned concepts."

Jan 1, 2008

By Anestis Vlyssides, Elli Maria Barampouti, Sofia Mai, ?postolos Vlyssides

"A new anaerobic reactor variation, the UASB/CO2-stripper reactor was conceived. It consisted of a conventional UASB reactor that recirculated the biogas produced. The sludge characteristics of this system were examined when treating high strength wastewater. From the data collected, it was obvious that the UASB/CO2-stripper system can satisfactorily operate at higher loading rates (25 g COD·L-1·d-1). A pronounced effect on the quality of the granular sludge was observed. The VSS/TSS ratio decreased sharply. A considerable decrease in the mean granule diameter was observed, while the specific gravity of the granules increased. The sludge bed porosity increased significantly leading to a considerable expansion of the sludge bed. These changes in the sludge properties led to a gradual shift of the system towards a fluidized bed process as far as its hydraulic characteristics were concerned.IntroductionIn recent years energy considerations and environmental concerns have increased the interest in direct anaerobic treatment of industrial wastes. The anaerobic method of waste treatment offers, under the present circumstances, a number of significant advantages with trivial or more serious drawbacks over other treatment methods. The major obstacle to the application of the process for this specific purpose is perhaps the difficulty of extending it to a stable and simple operational form. A number of reactor configurations has been developed leading to high biomass concentrations, e.g. the contact process, the filter reactor, the UASB reactor, and the fluidized bed systems, but the process stability problem still remains [1].A prime objective in the operation of anaerobic waste treatment process is the maintenance of a proper pH range. Thus, a possible solution to the process stability problem could be obtained by increasing alkalinity in the anaerobic systems. Therefore, the main objective of this paper is to present and evaluate the results of a system (UASB/ CO2-stripper) with increased alkalinity concentrations."

Jan 1, 2008

By P. H. Scaife

The pyrometallurgy industry faces a series of environmental challenges, based on local, national and global issues. While local impacts continue to be important, national and global concerns with Sustainable Development, Greenhouse emissions, Acid Rain and water resources are key strategic drivers for the industry. The environmental problems of the industry are well known: emissions of sulphur dioxides and carbon dioxide, disposal of arsenic wastes, consumption of fresh water, fate and impact of minor components/trace elements in raw materials (whether conventional or complex, or wastes). Solutions to these problems require the application of Cleaner Production principles (waste minimisation, energy conservation, product design to enable ease of post consumer recycling), new technology and scientific studies to assess impacts of discharges. A number of opportunities, driven by environmental concerns, have also been identified

Jan 1, 1994

By Aly M. Abdel-Rehim

The present work deals with a study of the mechanical activation of processing of Egyptian monazite by its simultaneous ball-milling and pressure leaching in order to improve the recovery of thorium and lanthanides from monazite. Experiments of simultaneous ball-milling and alkaline leaching of monazite contrary to autoclave leaching were carried out in stainless steel ball-mills of cylindrical shape under different conditions of temperature, pressure, time and alkali amount and strength. The ball-mills were heated and mechanically rotated in an electric furnace by means of roll mechanism. The effective rotation speed was fixed at 130 rpm in all tests. The charge of steel balls of different diameters was equivalent to 45% of the total mill volume. Monazite was charged in ball-mill without preliminary grinding. It is found that high rate of monazite leaching by ball-milling leaching method is achieved at lower temperature, shorter time and lower expense of alkali than in autoclaves. The results obtained show that complete recovery of thorium and lanthanides from monazite (99.8%) by simultaneous ball milling and alkaline leaching is attained at 140°C within 2 h. It is concluded that processing of monazite by its simultaneous ball-milling and leaching is mechanically activated and accelerated as a result of grinding action of steel balls that caused the continuous removal of the hydroxide product from reacting particle surfaces. This leads to the exposing of fresh and activated monazite particles surfaces to alkali leach solution and consequently the acceleration of the reaction of monazite processing.

Jan 1, 2006

By Hélio Wiebeck, Fabio J. Esper, Wildor T. Hennies, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz

"Natural rubber reinforced commonly with carbon black to produce vulcanized material, turns into a new environmentally friendly nanocomposite when carbon black is replaced by organically modified clays of Brazil. Carbon black is substance derived from the oil refining process with consequent pollution to the environment. Its substitution in this industrial process must contribute to diminish the oil derived products dependence. As the added clays are only a third in weight of the traditionally carbon black added, then, to obtain the same final volume it is necessary to add low cost neutral filler that does not damage the technological characteristics of the final material. This paper presents results using as neutral filler of this type rice husk ashes from industrial wastes. Experiences realized with this nanocomposite material show results of quality and technological characteristics similar or superior to those of the rubber made with carbon black.IntroductionTraditionally rubbers are black or a very dark color. But they can have different appearance when filler of distinct composition of the carbon black is used. The carbon black is substance derived from the oil gotten during the final phases of the mineral fuel treatment with consequent pollution of the environment. Carbon black show nanometric grain sized distribution and a depth black color, because these properties it is also used for computer printers inks production. The substitution of this substance, traditionally used as a reinforced load in the rubber production, will have to contribute in such a way to diminish the dependence of these products as to diminish the pollution of the environment. The present work shows the results of the use of another kind of mineral nanoparticulate material substituting carbon black in the production of some rubber products. This nanoparticulate material is the organic modification of smectite clay treated with some types of ammonium quaternary."

Jan 1, 2008

By A. Kapilashrami

Slag foaming proves to be both blessing and curse for the process productivity, depending on where in the process it occurs. In pyrometallurgical processes, slag foaming is often a result of chemical reactions taking place in the slag. As the slag composition and reaction rates are changing, foaming occurs under dynamic conditions. In the present work, slag foaming was studied with XRF. The foam displayed a fluctuating behaviour, unaccountable by existing models. The concept of foaming index was found not to be satisfactory in describing the foam, resulting in the need for alternative theories. The rate of fluctuations was seen to be related to the difference between rate of gas generation and rate of gas escape from the system (Ug-Ue) as well as the bubble sizes. Thus, model development of dynamic foaming phenomenon has to take the effective chemical reaction rate as well as the bubble sizes into consideration. The first step in obtaining foam is to form bubbles. In the present work, gas bubbles were generated through chemical reaction at interface between two immiscible liquids and the bubble formation was studied optically. The gas bubble size was seen to be uninfluenced by the reaction rate. However, bubble formation was seen to take place in one of the phases and since the bubbles consequently traversed the interface under the influence of buoyancy, the viscosity of the first phase was found to influence the final bubble size where increased viscosity would yield a larger bubble size.

Jan 1, 2006

By Laurentiu Nastac

"Two advanced control solidification technologies were studied in this article to improve the quality of the cast ingots as well as to control the solidification structure evolution during the plasma arc melting (PAM) processing of Ti-6-4 ingots: (i) electromagnetic stirring (EMS), and (ii) ultrasonic treatment (UST). The developed EMS modeling approach is based on the numerical solution of Maxwell's equations, fluid flow, and heat transfer equations, and mesoscopic modeling of the grain structure. The UST analysis tool is capable to model acoustic streaming and cavitation. It is used in this work to study ingot solidification under the presence of ultrasound. Predictions of the macrostructure, GET formation and primary dendrite arm spacing for PAM Ti-6-4 ingots processed with and without EMS or UST were discussed.1. IntroductionTitanium (Ti) alloys are melted, refined and cast into ingots through plasma arc cold hearth melting (PAM), electron beam cold hearth melting (EBM) and vacuum arc remelting (VAR) for jet engine applications. Process modeling has become a viable tool to optimize the PAM, EBM, and VAR processes. A comprehensive modeling approach to simulate ingot solidification phenomena in primary melting and secondary remelting processes of Ti alloys would include models for macroscopic mass transfer, heat transfer, fluid flow, acoustic, electromagnetic and species transport. The approach should also include microscopic models to predict the evolution of grain structure in solidifying ingots in conjunction with electromagnetic stirring (EMS) and ultrasonic stirring (UST)."

Jan 1, 2012

By P. C. Guillaume

Global plant modernizations or expansions cannot be considered in the same light as any other industrial investment project. Relationships between the partners, relationships and communications with the client, structure and organisation of the teamwork, schedule of the work, and a lot of other tasks and missions devoted to external contractors have to be defined considering one fundamental input: an operating plant. For an engineering company expert in processing, like UM Engineering, such a context requires a specific approach as well as specific procedures able to efficiently challenge the generated constraints. First of all, even if a detailed audit had been conducted at the beginning of the conceptual engineering phase, new elements will be discovered during the preparation and realization of the project, and must be continuously integrated. Consequently, a close proximity to the site is necessary. This is one reason why UM Engineering, most often, works in partnership with a local engineering company. The second important point for the client is that the operation must not be interrupted during the realization. In order to make that possible, UM Engineering has defined a specific project structure and organisation, integrating on a permanent basis the operators (the "users") in the project teams. This paper presents the way UM Engineering copes with this type of "multi-constraints" context with reference to the recent copper cellhouse modernization under realization for the CCR Refinery of Noranda Inc. in Canada.

Jan 1, 1999

By Luciano B. Oliveira, Alexandre M. Stumbo, Luis G. C. Marques, Valdo S. Marques, Sergio N. Monteiro

"Similar to the ethanol program, initiated more than 30 years ago, the recently created biodiesel program in Brazil is expected to rely on private initiative based on agribusiness for vegetable oil production. Campos dos Goytacazes is a large county in the northern of the state of Rio de Janeiro with land still available for oily vegetables plantation in addition to the land traditionally occupied by sugar cane plantation, which is used to produce ethanol. In order to extend the biodiesel program to Campos dos Goytacazes, the State University of Northern Rio de Janeiro (UENF) is conducting a technical project for the development of the infrastructure for biodiesel production. In this work, the infrastructure based on versatile equipment for biodiesel esterification built in the Center for Alternative Energy of the UENF is presented.IntroductionBiofuels are gaining worldwide attention as a possible economical solution for the prediction of declining reserves of petroleum and related increase in price of barrel. However, nowadays, a more relevant question is the climate changes caused by burning fossil fuels. This is especially the case of coal and petroleum based fuels, mainly gasoline and diesel that propel the majority of vehicles and generate a large amount of CO2 emissions responsible for global warming. This combination of economical an environmental problems is already providing a strong motivation to substitute conventional fossil fuels by renewable biofuels. More than just the interest of the market financial forces, government legislation is imposing a new order that obliges the use of biofuel. Many countries including the USA, the European Community, Japan and Brazil are committed to gradually substitute biofuels into their fleet of vehicles."

Jan 1, 2008