Search Documents

By A. D. MacPhail

The Highland Valley Copper partnership was formed in July 1986 and was the logical result of a mine with a large ore reserve but no adequate mill, and a mine with a large, modem mill but dwindling ore reserves. The original partners -Cominco and Lornex -were joined in January 1988 by Highmont Mining Co. which contributed a two-line concentrator. During 1988/1989, the Highmont mill was moved 7.5 km to adjoin the Lornex mill, forming what is now called the Highland mill, with a current nominal capacity of 130 000 tonnes per day. The mine is located 220 km northeast of Vancouver, British Columbia and is close to four communities in which personnel make their home: Logan Lake, Merritt, Ashcroft, and Kamloops. The map in Figure 1 2.2 shows the general area. Kamloops is a major service centre and is serviced by two railways, two major roads and a regional airport.

Jan 1, 1993

By Leonard Sugin

The requirements of today's and tomorrow's markets led to a new generation of facilities which handles large tonnages annually, loading them into larger vessels, at higher rates, efficiently and reliably, with minimum labor input, and significantly greater attention to the environment. A great variety of products are handled, including various grades of metallurgical and steaming coal, coke, iron ore in its many forms, shapes and moisture content, phosphates and fertilizer products, bauxite and alumina ores, limestone, sugar and grains, cement and many other products. When we examine the annual tonnages involved in these movements the economic value of handling these products on a bulk basis can be readily seen. Although nearly all these products have been handled by continuous bulk conveyors for many years, recent governmental response to environmental concerns require a re-evaluation of previous procedures. Most air pollution and emission control regulations and ordinances have recognized several specific sources of pollution. Detailed regulations and requirements have been developed concerning smoke emissions, emissions of visible air contaminants and particulate matter from power plants, heating plants, refuse burning equipment, coke ovens, steel furnaces, kilns, and other industrial installations. Although fugitive dust is also an environmental pollutant it is governed by regulations that are more general and therefore, more difficult to apply. A general definition of a "fugitive particle" is any matter which escapes or becomes airborne from an operation or which is emitted into the atmosphere without passing or being conducted through a flue, pipe, stack or other structure designed for the purpose of emitting air pollutants into the atmosphere. This paper deals with the aspects of fugitive dust emissions as they apply to shiploading. Fugitive dust emissions control is important not only because of environmental regulations but also to prevent the loss of valuable product, reduce housekeeping, and reduce breakdown and maintenance problems to land and vessel equipment. The environmental controls for a belt conveyor system are those which will restrict the emission of fugitive dust particles and can be considered as follows:

Jan 1, 1977

By A. M. Abouzeid, R. Hogg

Materials transport is involved in all phases of mineral processing. Bulk transport is necessary for moving materials between unit operations and through processing devices such as grinding mills. Differential transport is a primary mechanism for most separation processes. The basic mechanisms of transport and flow in particulate materials are reviewed and their role in materials handling and storage and in the performance of processing operations such as grinding and separation are discussed. Specific examples are used to illustrate current understanding of these transport phenomena and to indicate important research needs and opportunities.

Jan 1, 1989

By J. A. Dlas Lima

Alunorte is a metallurgical-grade alumina refinery located in northern Brazil. This plant which was designed to produce 1.1 million mtpy of calcined alumina, started operation in July 1995. A process information system was installed before refinery start-up. It has been a main factor in process improvements, which resulted in an increase in production from 1.1 to 1.5 million mtpy. This system has been particularly useful for analyzing data and allowing retrieval of data by process engineers. This paper describes how a quality monitoring system to evaluate all aspects and stages of production, as well as alumina silo level and blending percentage, was developed. This system was designed to give support to ISO 9002 certification, which happened in December 1998. The quality monitoring system was developed using Microsoft Excel 7.0 and makes extensive use of VBA macro. The primary users of the system are shift foremen, managers and engineers, who use it to track the process and avoid variations in alumina quality.

Jan 1, 2000

By D. J. Rose

The San Miguel Mine is owned by San Miguel Electrical Cooperative, Inc. and operated by Atascosa Mining Company, a wholly-owned subsidiary of Morrison-Knudsen Company, Inc. This multiseam, single-zone lignite surface mine is located near Jourdanton, Texas, 110 kilometers (68 miles) south of San Antonio. Lignite extracted from four closely-spaced seams is used to fuel the 400-MW San Miguel Power Plant. Recovery depths range from 7 to 37 meters (25 to 120 feet). The mine began stripping operations in the spring of 1980 and now produces approximately 2.5 million tonnes (2.8 million tons) of lignite annually. Atascosa Mining Company is responsible for production, maintenance, engineering, and management services. Production responsibilities include topsoil removal, overburden removal, lignite mining, spoil pile regrading and topsoil replacement, as well as ash disposal and construction and maintenance of water retention and diversion facilities.

Jan 1, 1984

By D. Gu

Breakage of rock by machine is one of the major methods of excavation. With the development of modern engineering techniques, the advantages of using this method have become even greater. Improving efficiency and reducing the cost of rock breakage is the main goal of mechanizing the rock-breaking operation. For a given stratum, the efficiency of a machine excavation depends, to a large extent, on the design and method of application of the tools used. In a planetary cutter head, the subcutter heads move like planets around the main drive shaft. The general structure of the cutter head is shown in Fig. 1. As shown in this illustration, the main drive shaft (1-1) is connected to the tie bar (1) and, thereby, to a gear(5) that meshes with a fixed-gear ring(2). The subcutter head (4) is rigidly connected to the gear (5) by the subcutter-head axis (2-2). When the main drive shaft (1-1) rotates, the subcutter head (4) rotates around the axis (2-2), under the action of the tie bar and with the help of sleeve pipe (3).At the same time, axis (2-2) also rotates around the main shaft (1-1). As shown in Fig 1, is the angle between the main shaft and the subcutter-head axis.

Jan 1, 1995

By Lynton Gormely

Oxygen transfer in a stirred tank bioreactor has been modelled mathematically to determine the trends in transfer efficiency (kg transferred per kWh) with transfer rate, tank depth, superficial velocity, and mixer power.

Jan 1, 1990

By William Hodder, Lisa Smiley, Ehsan Alav

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km and be lined using a precast concrete segmental tunnel liner with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT liner was grouted through ports drilled in the segments. The Westerly Storage Tunnel (WST) in Cleveland will extend approximately 2.93 km long and will be lined by using a similar precast concrete segmental tunnel liner with an internal diameter of 7,620 mm and external diameter of 8,230 mm. The WST liner was grouted using both grout ports built into the tail can of the TBM and through segments. Each tunnel was mined primarily in shale with varying levels of weathering and both tunnels had dry and wet sections. This paper will document the means and methods for grouting in each tunnel as well as the methods utilized to proof grout and the results found.

Jun 13, 2021

By Neville G. W. Cook, John Kemeny

Utilizing the principles of elastic-brittle fracture mechanics, stress-displacement relationships are derived for an elastic solid containing a slip plane consisting of various configurations of collinear arrays of cracks. These models take into account the heterogeneous nature of slip planes as observed in the lab and in the field, and are relevant to the behavior of rock containing faults, joints, bedding planes, and fractures. All of our models exhibit slip weakening behavior, and show regimes of both stable (aseismic) and unstable (seismic) deformation. For given configurations of cracks and applied boundary conditions, our results show explicit ly the energy released through unstable crack growth. For instance, it is found that two equal length cracks growing together release more seismic energy than, say, a large crack growing into a small crack. Also, by allowing cracks to coalesce, our models show multiple stick-slip events without crack healing or other geochemical means.

Jan 1, 1986

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The reliable quality assessment of grouting operations is one of the key issues in establishing impermeable grout curtains around shafts, drifts and tunnels. Reliable opera¬tional information on the decrease in the permeability of rock during the grouting process facilitates the assessment of the effectiveness of the completed curtain and assures production quality. Quality control and assurance also fa¬cilitates the early detection and elimination of possible de¬fects in the grout curtain. Thorough control of the grouting process provides the capability to evaluate decreases in the permeability of water-producing fracture zones prior to the beginning or the continuation of excavation of the shaft, tunnel or drift. In order to achieve this objective, post¬grouting hydrodynamic investigations are conducted prior to the initiation or re-initiation of work on the underground workings to measure the decrease in the permeability coef¬ficient of aquifers during grouting operations. 8.1 QUALITY ASSURANCE AND CONTROL OF THE ISOLATION OF ROCK BY GROUTING THROUGH HOLES DRILLED FROM THE SURFACE Quality assurance and control are based on measuring the decrease in the permeability coefficient of water-pro¬ducing horizons as a result of injecting grout into the drill¬holes. For this purpose, the value of the acceptable residual permeability coefficient is calculated beforehand based on the acceptable value of ground water inflow into the shaft, drift or tunnel as specified by the "construction norm and integrated practice (SNIP)" (Anon., 1976). Having ob¬tained the values of aquifer thickness, permeability, and head distribution for each aquifer from flowmetric data (dis¬cussed in Chapter 3), the average value of the permeability coefficient of all aquifers intersected by the shaft is calcu¬lated as [ ] where Ki is the permeability coefficient of the "ith" aqui¬fer; Pi is the pressure of the "ith" aquifer; and M; is the thickness of the "ith" aquifer. The total expected inflow of ground water into the shaft is [ ] where RK is the radius of the contour of influence; RCFB is the radius of the shaft; and p is the coefficient of dynamic viscosity of the ground water. The necessary reduction of the coefficient of permeabil¬ity of the aquifer [ ] where Q is the expected inflow of ground water into the shaft from eq. 8.2; Q.-fin is the acceptable inflow of ground water; and a is the safety factor. By knowing the average permeability value of the rock and the permeability reduction coefficient, it is possible to determine the value of the acceptable residual permeability coefficient for all the aquifers [ ] The values of the permeability coefficient, pressure, and thickness for each aquifer are determined from the data gathered during the hydrodynamic investigations conducted in grout holes prior to beginning the grouting operations as discussed in Chapter 3. After injecting the grout into the first of the holes, the injection into each of the following grout holes is preceded by repeated hydrodynamic investi¬gations. Using the data obtained for each water-producing zone, a graph is constructed where the numbers representing the grout holes in their order of grouting are placed on the abscissa, and the values of the aquifer permeability coeffi¬cient are placed on the ordinate (Fig. 103). This curve char¬acterizes the change in permeability of the given hydro¬stratigraphic unit as grouting operations are completed, one hole at a time. The results of grouting operations are considered to be positive when each sequential observation records a steady decrease in the permeability of the aquifer. The permeabil¬ity measured prior to the injection of the grout into the last hole must be lower than or equal to the acceptable perme¬ability as determined by the application of eqs. 8.1 through 8.4. Table 8.1 presents illustrative data on the hydrogeo¬logic properties of aquifers at a mine shaft prior to the initiation of grouting operations. Data also are presented on the reduction in the permeability coefficient during the in¬jection of the grout. The shaft in question intersects eleven aquifers. Based on data concerning aquifer pressure, thick¬ness, permeability, and the expected inflow rate of water for each of the strata, the average permeability coefficient is calculated according to eq. 8.1 as K = 0.2 x 10-12 m2. The

Jan 1, 1993

By H. V. Alminas

The U.S. Virgin Islands consist of three major islands (St. Thomas, St. John, and St. Croix) and some 50 smaller islands that are located primarily along the coasts of St. Thomas and St. John. St. Croix, the largest of the islands, is located approximately 160 km south-southeast of San Juan, Puerto Rico and is about 218 km in area (Fig. 1). St. Thomas, the second largest island is located 64 km east of Puerto Rico and incorporates approximately 77 km2. St. John is located immediately to the east of St. Thomas and incorporates approximately 49 km2. The climate in the U.S. Virgin Islands is maritime tropical. The average annual rainfall at higher elevations is 127-152 cm and at lower elevations 51-76 cm. There is no well-defined wet or dry season. Temperatures generally average in the 80's (F°) with only a 5°-7° F variation throughout the year.

Jan 1, 1987

By K. C. Corin, B. McFadzean, J. G. Wiese

The Bushveld Complex of South Africa contains almost 90% of the world’s reserves of platinum group minerals (PGMs). In the flotation of PGMs, there are significant challenges arising from the need to treat ever-decreasing grades of the relevant ore deposits. The major challenge in the flotation of these ore bodies is the control and management of the gangue minerals, particularly silicates such as orthopyroxene and plagioclase feldspar which are often rimmed with talc which makes them naturally floatable. It has been shown that various polysaccharide depressants such as CMC and guar have different properties in terms of depressing the gangue minerals. Since the PGMs are often associated with sulphides, copper sulphate is widely used as an activator in PGM flotation but can inadvertently activate the gangue minerals and reduce the recovery of PtTe2 which accounts for up to 40% of the Pt in the Platreef ore body. Depressants also reduce the mass of solids reporting to the froth and can thus destabilize the froth. This effect on the froth can be mitigated by using higher frother dosages or water of higher ionic strength. In summary due care needs to be taken to carry out site test work to develop an optimum ratio of collector, frother, activator and depressant to ensure that the highest grades and recoveries of the PGEs are obtained while reducing depressant dosage as much as possible. Chromite recoveries can be reduced through the application of gravity separation or reducing entrainment through reduced water recovery. INTRODUCTION The Bushveld Complex located in the north of South Africa contains the world’s largest deposit of Platinum Group Minerals (PGMs) (1). The so-called upper Critical Zone of the Complex hosts the largest concentration of platinum group elements (PGEs) in the world. The Zone hosts the Upper Group Chromitite No.2 (UG2) reef and Merensky Reef as well as the Platreef mineralization of the northern limb of the Bushveld Complex. The Merensky pegmatoid Zone contains the base metal sulphide grains and associated PGMs. Of particular importance to the topic of this paper is the occurrence in these reefs of various gangue minerals. The Merensky Reef consists predominantly of orthopyroxene (~60%), plagioclase feldspar (~20%), pyroxene (~15%), phlogopite (5%) and occasional olivine. Secondary minerals such as talc, serpentine, chlorite and magnetite have widespread occurrence. Of these, talc is the only mineral to show significant natural floatability (2,3). Although present in small amounts talc is closely associated with pyroxene and imparts significant floatablity to the high concentrations of pyroxene present in these ores (4). The base metal sulphides consist predominantly of pyrrohtite (~40%), pentlandite (~30%) and chalcopyrite (~15%). The major platinum group minerals are cooperite (PtS), braggite [(Pt,Pd)NiS], sperrylite (PtAs2) and PGE alloys. The UG2 consists predominantly of chromite (between 60 – 90% by volume) with lesser silicate minerals (5 – 30% pyroxene and 1 – 10% plagioclase). Other minerals present in minor concentrations, can include silicates, oxides and base metal sulphides. Total PGE varies by locality but on average range between 4 and 7 g/t. The PGMs present in the UG2 Reef are highly variable, but generally the UG2 is characterised by PGE sulphides such as laurite (RuS2), cooperite (PtS) and braggite [(Pt,Pd)NiS. The base metal sulphides consist predominantly of chalcopyrite, pentlandite and pyrrhotite. The Platreef is located in the northern limb of the Bushveld Complex. This reef consists of a complex assemblage of rock types, with pyroxenites, serpentinites and calc-silicates being the most abundant. Base metal mineralization and platinum group element (PGE) concentrations are found to be highly irregular, both in value as well as in distribution. The predominant platinum group minerals (PGM) in the mined area of the Platreef are the PGE tellurides, alloys, arsenides and sulphides. T

Jan 1, 2019

By John Ralston, Rossen Sedev, Nicola Richards, Quinn Anthony, Geoffrey Reynolds

Derivatised 2,4-diketopyrimidine groups have been anchored to planar gold surfaces as self¬-assembled monolayers (SAMs) for chemical and photochemical studies. Three derivatives, 5-methyluracil (thymine), 5-trifluoromethyluracil and 5-nitrouracil, were chosen for the specific moiety present at position C-5, which can exert strong or weak inductive effects on the adjacent aromatic ring. The measured acidity constants decrease from 5-methyluracil to 5-nitrouracil as the inductive properties of the group at C-5 position increase. When grafted to the surface the acidity constants increase, albeit still adhering to the expected inductive trend. The functionality also exerts an influence on the surface wetting properties. Surface wettabilities indicate that the orientation of the pyrimidine groups at the surface occurs so that the C-5 position has a direct effect upon the surface chemistry. Upon dimerisation the surface contact angles increase signifi¬cantly. At pH 11 the contact angle changes reflect that the dimer has a higher pKa than the monomer. The monomer surface is deprotonated at this pH while the dimer surface is partially deprotonated, leading to changes in contact angle of up to 22 degrees. Large changes in contact angle were observed for 5-nitrouracil which were independent of surface charge and were appar¬ently due to conformational changes alone. Electrowetting of three fluoropolymer surfaces by electrolyte solutions was studied with the sessile drop method. The electrowetting curve (contact angle/potential) is analogous to the elec¬trocapillary curve (surface tension/potential) and may be described by a combination of the Young and Lippmann equations. We demonstrate that for some specific surfaces a systematic deviation occurs at positive potentials. This departure is attributed to double layer effects, namely the adsorption of hydroxide and halide anions. pH, ionic strength and polymer composi¬tion can all influence electrowetting behaviour.

Jan 1, 2003

By Robert C. Dunne, Jeffery P. Vaughan

The Archean ores of Western Australia are in total the largest producers of gold in Australia. In addition to numerous small and medium sized deposits, the province also contains the giant Kalgoorlie Golden Mile deposits. A variety of different gold ore mineralogical associations has lead to the development of a number of different processing routes for both refractory and non-refractory ore types. Intense weathering and lateritization of Archean greenstones in the semi-arid Yilgarn region have resulted in the development of a deeply oxidized profile (60-100m) above most sulphide orebodies. Residual and re-deposited supergene gold within iron oxide/silica gangue of this zone responds well to CIP, CIL, heap and vat leaching techniques. Although gold is easily liberated in principal from oxidized gangue, in practice recoveries are sometimes affected by iron oxide coatings on gold grains, and by clay minerals which can interfere with plant performance. Refractory ore types in the Eastern Goldfields fall into three main categories - pyritic, arsenopyritic and telluride-bearing. Pyritic ores may be either free milling or require roasting. The difference appears to depend largely on whether gold occurs along grain boundaries or fractures, which can be liberated by grinding, or whether gold occurs as inclusions within pyrite grains and therefore cannot be satisfactorily liberated by grinding. Arsenopyrite bearing ores are not well understood and are complicated by what appears to be a variable degree of gold solid solution, in addition to included gold. Gold occurring in complex gold-silver telluride assemblages has traditionally been recovered by roasting in the Eastern Goldfields.

Jan 1, 1987

By Frank G. Horino, V. E. Hooker

INTRODUCTION The determination and use of mechanical properties of rock in engineering and rock mechanics are rapidly developing. Many of these properties are determined on intact rock specimens; thus, their application and repre¬sentation of rock mass properties may be limited. How¬ever, relative information often provides useful guidance in the solution to mine design and stability problems. Summarized in this chapter are some of the stan¬dardized techniques and procedures currently used to obtain these mechanical properties. Typical applications of the use of these properties are also presented. Stan¬dardized techniques include those advanced by the American Society of Testing and Materials (ASTM), International Society of Rock Mechanics (ISRM), US Bureau of Mines (USBM), Canadian Dept. of Mines and Technical Surveys, South African Institute of Min¬ing and Metallurgy, and other individual investigators. Information on the mechanical properties of rock and the behavior of the rock under a given system of stresses represents a necessary part of the information for rational engineering design for any given mining op¬eration. The mining method, the type and extent of sup¬port, the extraction ratio, the overall dimensions of the mine, and the orientation of the rooms and pillars are all decisions that are influenced by the mechanical prop¬erties of the ore, roof, and floor material under various stress systems and the magnitude and direction of the in situ stresses (Hooker, Bickel, and Aggson, 1972). Initial mechanical property information regarding a structure or mine property is generally obtained by two basic techniques: (1) static and dynamic property tests are conducted on intact and fractured rock specimens of exploratory drill core, and (2) dynamic properties are obtained by borehole logging techniques. When mining access becomes available, and as the mining horizon is expanded, additional information can be ob¬tained to verify preliminary mine design values. This chapter presents some of the standardized tech¬niques and equipment currently used in obtaining me¬chanical property data in the laboratory. The properties considered are: (1) uniaxial compressive strength of intact rock core specimens, (2) uniaxial compressive strength of rock cores containing planes of weakness, (3) triaxial compressive strength of intact rock core specimens, (4) triaxial compressive strength of cores with a plane of weakness, (5) Young's modulus, (6) Poisson's ratio, (7) density or apparent specific gravity, (8) modulus of rupture, (9) indirect tensile strength, and (10) creep characteristics. Where possible, an at¬tempt will be made to evaluate each property measure¬ment in relation to the problems of rock mechanics and application of results. TEST SPECIMENS The selection and care of drill core for laboratory testing require some consideration. It is recognized that laboratory-determined properties are not necessarily rep¬resentative of an in situ rock mass property. However, relative information between beds or zones of interest is still valuable information in selecting mining horizons and preliminary design criteria. To provide statistical data the number of drill core samples selected to repre¬sent each of the areas of interest should be from a mini¬mum of three to a maximum of ten test specimens. A judgment must also be made on site as to whether the recovered drill core should be wrapped and sealed in plastic to preserve moisture. On the one hand investiga¬tions of air-dried and saturated specimens have shown that moisture significantly affects the elastic properties and strengths of many rock materials (Obert, Windes, and Duvall, 1946; Colback and Wiid, 1965); on the other hand it is apparent that most core drilling is done with water which may saturate the specimen to a greater extent than in the in-situ condition. Whether or not the decision is made to retain the moisture, the core should be delivered to the laboratory as soon as possible after recovery for subsequent specimen preparation and testing. Specifications Shape: The shape of the specimens influences lab¬oratory testing in two ways: (1) time and cost of sam¬ple preparation and (2) strength of the material. Cy¬lindrical specimens of drill core are by far the least time-consuming to prepare for static or dynamic labora¬tory testing. In addition, the cylindrical shape lends it¬self to a more uniform stress distribution throughout the sample than other shapes, such as rectangles and hexa¬gons. The compressive strengths of various shapes have been studied (Grosvenor, 1963, and Price, 1960), and results indicate that the cylindrical specimens usually provide the highest strength for a given height-diameter ratio. However, reduction in strength from a cylindrical shape to a rectangular in situ pillar is not regarded as significant in relation to other considerations such as planes of weakness in a pillar or safety factors in the design process. Length-Diameter Ratio: The length-to-diameter ra¬tio, LID, has a significant effect on the compressive strength. Various recommendations have been made to use standard LID ratios ranging from 2 to 2.5 to 3 (ASTM, 1975c; ISRM, 1972). However, past work by others such as Obert, Windes, and Duvall (1946) has shown that excellent results can be obtained using LID ratios from 2 > (LID) > >/s. In selecting an LID ratio for testing, one should keep in mind the amount of material available for testing. In many instances, this may be limited. Thus, a shorter specimen such as 1: 1 LID may be necessary to provide enough test data for statistical analysis of results. Sec¬ond, it may be desirable to obtain elastic constants dur¬ing the test. This generally requires instrumentation such as linear variable differential transformers (LVDTs) or strain gages near the center of the specimen. In this case, an LID of 2.5 or 3 is desirable so that the instru

Jan 1, 1982

By James Matlock

The announcement of a minable reserve of 13.6 Mt (16 million tons) averaging 0.9 g/t (0.027 oz per ton) Au and 2.4 g/t (0.71 oz per ton) Ag for the open pit-heap leach reserve at Red Mountain No. 3 in Ouray County, Colorado, by Cornucopia Resources in November 1985 brings another open pit-heap leach precious metal ore body to the production stage. With about 8.2 Mt (9 million tons) of waste and metallurgical studies showing acceptable recovery rates, low reagent consumption, and good final percentage recovery, Red Mountain is a discovery that will add to the precious metal inventory of the US. Frank Baumgaruler of Denver, CO, recognized the precious metal potential in Red Mountain No. 3 and acquired all of the old claims. James Matlock conducted a field reconnaissance over Red Mountain No. 3 independently of the Baumgartner activities and recognized epithermal alteration and mineralization in the Tertiary volcanics. He recommended acquisition of the ground and was able to obtain rights and drill six core holes for Amoco in 1982. Amoco drilled a further nine core holes in 1983, but then dropped the property. Cyrano Resources examined the data and through its consulting geologist, V.F. Hollister, acquired the rights dropped by Amoco. In 1984 Cyrano began further drilling of the ore zone demonstrated by Amoco but they were then acquired by Cornucopia Resources. Cornucopia completed development of the property and commenced the permitting process in 1986. The property was recognized as a disseminated gold deposit by both Baumgartner and Matlock, and both deserve credit for properly evaluating mineralized outcrop in the Tertiary volcanics. However, Cornucopia recognized the profit potential in the heap leach exploitation of the ores and de- serves credit for completion of premine feasibility studies. The discovery is clearly a geological one, but the premine engineering studies were essential to the conversion of the prospect to a commercial mining enterprise. The deposit lies on the circular bounding fault of the Silverton caldera. Two reprints follow that help understand the geologic setting of the ore controls.

Jan 1, 1990

By Xuehui Zhang, Yun Bai, Qiaosong Li, Huiming Wu

"Construction activities account for a large share of the global Greenhouse Gas emission. In the past 10 years, project decision-makers and researchers have been paying more attention to the carbon emission of tunnel projects. In this paper we study the carbon emission calculation in shield tunneling. The objective of this paper is to: (1) analyze the complex variables which affect the total emission of shield tunneling; (2) develop and illustrate a new data-mining-based method to estimate the carbon emission in the construction phase; (3) assess the emission prediction reliability of a data-mining-based method—the Randomforst model, with R programming language. This study is based on a large-diameter shield tunnel built in Shanghai, China, and shows that a reliable predictive performance can be achieved with this new data-mining-based method. INTRODUCTION Climate change caused by the Greenhouse Gas (GHG) emission has been a hot topic in recent 20 years. Both governments and non-government-organizations are trying its best to control the climate change. Since the 1990s, the general consensus is that carbon emission reduction and carbon sinking (the work of capturing the emitted carbon) are two ways of mitigating the global warming effect, with the former being more exercisable. The challenge posed by global warming also motivates the project decision-makers to take measures to reduce the GHG emission. The 5th Assessment & Report on Climate Change (published by IPCC, the Intergovernmental Panel on Climate Change) suggests that building industry contributes to 5% of the total direct emission. The building industry has shown more awareness of the impact of GHG emissions with construction activities. Shield tunnels act as an important component of the infrastructure system, and have been the dominant way of utilizing the underground space, as well as a competitive alternative to passageway underneath rivers. To study the environmental effects of shield tunneling, there is a need to quantify the carbon emission of shield tunnel construction."

Jan 1, 2016

By Bruce Hern

The last 10 years have seen a dramatic increase in the requirements for product coal quality control. This has led to electric utility sulfur scrubbing, metallurgical blast furnace optimization and coal producer blend and yield optimization. To achieve this improved level of control, coal producers are designing facilities that emphasize new technology. New facilities will be designed and existing facilities will be retrofitted with state-of-the-art technology to meet quality control standards that are dictated by the market. The first step in designing for process control requires the identification of those parameters to be controlled and the upsets that can cause variances in the final shipped product quality. The most common parameters that require control are the surface moisture (%), ash (%), pyritic sulfur (%) and gross calorific value (Btu). Total moisture is that moisture that exists on the surface of the particle and is inherent in the particle itself. For the purposes of control, the total moisture is monitored, while surface moisture is controlled. Ash is the inorganic residue remaining after all other constituents are burned away at 75O°C( 1382°F)(ASTM, 1992). Sulfur is the amount of total sulfur that exists either as pyrite (FeS2), inorganic sulfate (FeS04), or organic sulfates (C4H4S) (Leonard, 1979). Currently, pyrite is controlled and total sulfur is monitored. The gross calorific value is the amount of heat produced when a unit quantity of coal is ignited under specified conditions. In this case, a l-g (0.03-oz.) sample of coal is ignited in an isoperibol waterbath and the temperature rise of the water bath is observed. The moisture and ash-free (MAF) Btu is relatively constant for a given seam, resulting in the whole calorific value being a function of the moisture and ash levels (Leonard, 1979).

Jan 1, 1994

By C. K. Blair, V. J. Hucka, E. P. Kimball

In central Utah, a coal mining operation is taking place under an 0.5-m (20-in.) pressurized natural gas pipeline. The room-and-pillar method with pillar extraction is being used to extract the coal from the seams. The pillars beneath the pipeline will not be extracted; however, there is a possibility that some subsidence may occur due to pillar failure. To assess possible damages on the pipeline, an attempt has been made to predict subsidence in the area where pillars may collapse. The resultant values of subsidence strain and slope have been used to determine the magnitude of strain, stress, and shear induced in the pipeline. Also, a network of survey points has been installed along the pipeline to detect ground move¬ment that would indicate excessive subsidence.

Jan 1, 1987

By P. C. Thakur

Methane has been a hazard since the beginning of coal mining and has influenced, more or less, every aspect of coal mine design. It is receiving increased attention lately because the rate of methane emission in coal mines is increasing as increasing demand for coal leads to exploitation of deeper seams and the use of higher productivity equipment. Consequently, the government and private industries have directed a great deal of effort towards understanding and solving the problem of methane emission in coal mines. In the United States, Consolidation Coal Company has pioneered research in this area since the early 1950's.1 Currently this work is being expanded by Consol through the Mining Research Division of the parent company, Continental Oil (Conoca), to find new techniques for degasification of virgin areas as well as control of methane in gob areas. Basic reservoir properties of coal seams, such as gas content, reservoir pres-sure, diffusivity, porosity and permeability are better understood today largely through the efforts of the U. S. Bureau of Minese2,3,4 It is possible now to identify and model the basic mechanism of gas emission from coal and to forecast steady as well as unsteady state emission of methane in coal mines with some degree of reliability. Combining this knowledge with any ventilation simulator should often identify problem areas in advance and permit adequate methane control measures to be planned.5 Another recent innovation in methane control is the horizontal hole drilling technology. The U. S. Bureau of 1-1ines and the Mining Research Division of Conoco have independently developed techniques for drilling horizontal holes 300 to 600 m deep6 The Bureau's method employs a rotary drill string while Conoco uses a non-rotating string with a down hole drill motor. It is the authors' view that the latter provides more positive control on bore hole deviation both vertically and laterally and appears to be faster, though somewhat more difficult to operate. The rate of methane emission depends on a number of factors which can be broadly classified in two groups. These are (1) the basic reservoir properties of

Jan 1, 1977