Search Documents

By M. N. Shetty

LARGE copper whiskers (-100 p) of 11111 orientation were tested in a floor-model Instron testing machine, at liquid nitrogen temperature. (Testing methods will appear elsewhere.) Whiskers deformed by twinning after some initial deformation. A load-elongation curve at the onset of twinning is reproduced in Fig. 1. Twinning was confirmed by taking a back-reflection Laue picture, using a slit colli-mator, which showed distinct splitting of reflections. The tensile stress reached just before twinning is about 1.4 x 107 g per sq cm (-7.0 x106 g per sq cm—resolved shear stress) which drops to 1.2 x107 g per sq cm (-6 x 106 g per sq cm—resolved). This twinning stress is about five to ten times larger than the value for bulk single crystals of copper deformed at 77°K (-106 g per sq cm—resolved). Twinning models based on Cottrell-Bilby's pole mechanism are discussed in detail by Venables.' In the present work a mechanism based on the idea of failure of a Lomer-Cottrell barrier by recombination will be proposed. An L-C barrier may fail either by recombination or by dissociation.3 Fig. 2 provides the necessary information. It shows that the stress necessary to break such a barrier is about 1.8 x 107 g per sq cm by recombination and 4 x 107 g per sq cm by dissociation at 77°K. The twinning stress reached by whiskers is comparable to the stress level required for failure of an L-C barrier by recombination. (Stroh himself points out that his calculations should not be taken too literally.) We consider a segment of the L-C dislocation which has recombined (AB in Fig. 3) over a length to form the total dislocation which then glides in the

Jan 1, 1965

By Cyril Stanley Smith

IsolatEd alloys of copper and silicon were prepared and examined by chemical methods more than one hundred years ago, but it was not until the work of Rudolfi l that the equilibrium relations were studied. The early history of the alloys was well described by Baradue-Muller 2 and need not be further discussed here. The diagram of Rudolfi, based entirely on thermal observations, showed sillcon to be soluble in copper up to 4.5 per cent. at 849" C., at which temperature there was a peritectic horizontal resulting from the formation of a ß phase with about 7.4 per cent. silicon from a and liquid with 7.85 per cent. silicon. The ß phase was believed to form a eutectic with Cu3Si at 820" C. and 9.8 per

Jan 1, 1929

By Cyril Stanley Smith

IsolatEd alloys of copper and silicon were prepared and examined by chemical methods more than one hundred years ago, but it was not until the work of Rudolfi l that the equilibrium relations were studied. The early history of the alloys was well described by Baradue-Muller 2 and need not be further discussed here. The diagram of Rudolfi, based entirely on thermal observations, showed sillcon to be soluble in copper up to 4.5 per cent. at 849" C., at which temperature there was a peritectic horizontal resulting from the formation of a ß phase with about 7.4 per cent. silicon from a and liquid with 7.85 per cent. silicon. The ß phase was believed to form a eutectic with Cu3Si at 820" C. and 9.8 per

Jan 1, 1929

COLUMBIA SECTION Holds four sessions during year. Annual meeting in September or October. S. S. FOWLER, Chairman, J. C. HAAS, Vice-Chairman, LYNDON K. ARMSTRONG, Secretary-Treasurer, 720 Peyton Bldg., Spokane, Wash. W. H. LINNEY, J. F. MCCARTHY. A special meeting of the officers of the Columbia Section was held in Spokane, Wash., Jan. 10, 1918, for the purpose of organizing and nominating members to the principal committees of the Section. Present: J. C. Haas, Vice-chairman; W. H. Linney, Past Chairman; and L. K. Armstrong, Secretary. J. F. McCarthy, Wallace, Idaho, was appointed fifth member of the Executive Committee. The following were appointed to the Membership Committee: R. M. Betts; for Oregon; W. J. Hall, for Idaho; J. M. Porter, for Washington. A member for British Columbia will be appointed later. The following were appointed to the Committee on Papers: Prof. F. A. Thomson, Moscow, Idaho; Prof. L. 0. Howard, Pullman, Wash.; H. S. Lee, Rye Valley, Ore. A fourth member, representing British Columbia, is to be appointed later. The following members were appointed representatives on the Executive Committee of the Spokane Engineering and Technical Association: J. C. Haas, W. H. Linney, F. A. Ross, L. K. Armstrong. The Treasurer reported a deficit, resulting from the participation of the Section at the Northwest Mining Convention in 1916. It was recommended that the Institute be petitioned to make good this deficit, in addition to the usual annual allowance. The members of the committee who were present expressed their desire to be of greater service in the present war, and discussed at some length the possible means of carrying out their desires. It was later decided to reopen the subject at a subsequent meeting of the Section, or to present it to the Executive Committee of the Spokane Engineering and Technical Association for discussion and cooperative action. L. K. ARMSTRONG, Secretary.

Jan 3, 1918

"Located on the Big Hole River, three miles from Divide, Montana, and 21.75 miles from Butte.Built in 1899.DAM: Rock-filled wooden crib, 512 ft. long and 57.5 feet high.SPILLWAY: Equipped with flash-boards 189 ft. long, 8 ft. 10 inches high.PENSTOCKS: Two 8 ft. diameter of steel, each branching and supplying two wheels.WHEELS: Four double horizontal, double discharge turbines, made by The James Leffel & Co., 1,000 h-p., 180 r. p. m., direct connected to generators, operating at 60 ft. head. GENERATORS: Four G. E., revolving field, 750 k-w., 180 r. p. m., 800 volt, 3 phase, 60 cycle alternators.EXCITERS: Two water-wheel driven exciters.TRANSFORMERS: 12 250-k-w. G. E. air blast, primary 15,000 volts, Secondary 800 volts.OPERATION: The plant operates essentially as a peak load plant. Except in flood period, there is insufficient water to operate at full load continually. In December its average output is about 500 k-w."

Jan 1, 1913

By J. M. Weehuizen

Complete details are given of the drilling method by which two shafts were sunk at the new Beatm'x mine of Staatsmijnen in the Netherlands. The nature of the rock strata in the Dutch mining district determined choice of the drilling rather than the freezing method. Data for each step and details of the equipment used are given in the illustrations. Staatsmijnen was founded in 1902 with government financial backing, but it is run as a private enterprise, on a commercial basis, with the normal fiscal obligations. The company now has four mines in operation with annual outputs amounting to 7 1/2 million tons of coal. In 1952 it was determined that a new mine—the Beatrix—would be opened. Details of the shaft-sinking operation are described in this paper. SHAFT LOCATION The coal-bearing carboniferous rock in the Dutch mining district is overlain almost completely by soft water-bearing strata, which at the site of the new shafts are about 1600 ft thick. The sinking of the new shafts through this soft water-bearing overburden (Fig. 1) is a costly and time-consuming affair. From the two availaible sinking methods: 1) Poetsch's well known freezing method or 2) the drilling method of Honigmann-de Vooys, the latter was preferred, not only because of its relative cheapness, under the prevailing conditions, but primarily because by using the drilling process, a special type of shaft lining of steel, concrete, and bitumen could be used. The new shafts, located 330 ft apart, have an inner diameter of 18 ft, 4 1/2 in. The boreholes, which have a diameter of 25 ft and which were drilled through nearly 1600 ft of overburden and some 100 ft of carboniferous, each contain more than 29,000 cu yd—by far the largest in the world. DRILLING METHOD The drilling method is based on the use of mud-flush—a thin mixture of clay and water—to keep the borehole filled during the entire drilling period and during insertion of the lining (Fig. 2). The pressure of the mudflush against the borehole wall is greater than that of the water in the surrounding

Jan 1, 1961

By M. Prats

This paper presents a method for obtaining the correct values of the breakthrough sweep efficiency of the staggered line drive, taking into account the proper shape of the breakthrough streamline. Results obtained were different from those previously published, which were obtained by using an inexact shape of the breakrhrough streamline. INTRODUCTION In Section 9.31 of Muskat's' The Flow of Hotnogeticous Fluids Through Porous Media, it is stated that in a staggered line drive flood "the streamline of highest average velocity [is] the line of centers between input and output wells" (see Fig. I). Muskat used this concept to determine the relationship between the breakthrough sweep efficiency and the geometry of the staggered line drive pattern. Although it is clear from symmetry considerations that the breakthrough streamline passes through the midpoint between input and output wells, it is equally clear, as shown in Fig. 239 of Ref. 1, that the breakthrough streamline is not represented very well by the straight line joining the input and output wells. Therefore, it is desirable to determine the proper relationship between the breakthrough sweep efficiency and the pattern geometry by using the proper shape of the breakthrough streamline. METHOD OF SOLUTION It was found that the effect of the geometry of the staggered line drive on the breakthrough sweep efficiency can be investigated easily by making use of the method developed in Ref. 2. With this method, it can be shown that the general complex potential for the staggered line drive, which can be considered as a rectangular five-spot, is given in the coordinate system of Fig. 1, by O(z) = In cn(z\m) = +(x,y) + i $(x, y) . (1) where z = x + iy, +(x, y) is the potential distribution and $(x, y) is the stream function. The function cn (zm) is a Jacobian elliptic function of parameter m and has simple zeros at z,. = (2n + 1) K + 21iK and simple poles at z, = 2nK + (21 + 1)iK. Thus, the complex potential behaves like a(z) = ln(z - zr.) in the neighborhood of the production wells and behaves like a(z) = - ln(z - Z,) in the neighborhood of the injection wells. Since (z - z1.v) = rll.ei, we note that the potential + has the proper logarithmic behavior near the two wells, while the stream function $ varies with the angle, decreasing clockwise around the production well and increasing clockwise around the injection well. The functions K(m) and K'(tn), related by K(m) = K'(m,), where m + m, = 1, are known as the complete elliptic integrals of the first kind. By use of other properties of the Jacobian elliptic functions, the general stream function distribution for the staggered line drive can be obtained from Eq. 1: From the Jacobian elliptic function values, sn(0lm) = 0 dn(O(m) = cn(0jm) = 1, and f[K'(m)Iml = 03, it follows that the stream function given by Eq. 2 satisfies the proper symmetry conditions near a production well P located at [K(m), 01 and an injection well I located at [0, K' (m)]. That is, the line IOP in Fig. 1 is a streamline with value G (0. 0) = -0. and the straight lines connecting I and P to the point [K(m), K' (m)] is a streamline of value $[K(m), K' (m)] = -7/2. Similar symmetry conditions are obtained near other wells. It should be nuled that for m = m1, = 0.5, Eq. 2 reduces to the stream function distribution of the regular five-spot given in Ref. 7. SHAPE OF THE BREAKTHROUGH STREAMLINE It is apparent, from symmetry considerations, that the breakthrough streamline ($,) passes through the point [K(m)/2, K' (m)/2]. Its value there is so that the shape of the breakthrough streamline $,, is given by

Jan 1, 1957

By M. J. Stewart, F. Weinberg

PREVIOUS investigations into convective flow in molten metals have examined systems in which the length-to-height ratio of the enclosure is large, usually using long graphite boats.''2 In normal castings this ratio is generally small and it is not possible to extrapolate the results of previous work to casting configurations. The present investigation was undertaken to examine liquid flow in systems of low length to height ratio. The apparatus used for the experiments is shown in Fig. 1. The molten zone of tin is contained in an aluminum mold of inside dimensions 6.4 by 6.4 by 0.31 cm. A heating block containing a resistance coil is attached to one end of the mold and a cooling block is attached to the other end. These are used to produce a wide range of temperature differences across the mold. The mold is contained in a stainless steel tank which is heated from the outside by resistance heaters to give the required operating temperature during the experiment. Temperature measurements in the molten tin are made with an iron-constantan thermocouple PT equal to 5 atm. The phase diagram derived by us was the same as that found by Krivsky and Schuhmann, except for a similar discrepancy in one boundary line representing the gas composition in equilibrium with SO a. The vapor pressures of the pure components can be neglected at 1700°K, 1 atm and 2500°K, 5 atm. There-fore, in these cases PT is essentially the total pres-sure in the system. This is valid for all the diagrams presented by Krivsky and Schuhmann except for the one at 2500°K and 0.01 atm, where the vapor pressure of silicon is comparable to PT.6 This work was supported in part by the American Iron and Steel Institute. 'C. E. Wicks and F. E. Block: Thermodynamic Properties of 65 Elements, U S. Bur Mines, Bull. No. 605, 1963. R. P. Elliott: Constitution of Binary Alloys, 1st supplementary, McGraw-Hill Book Co., New York, 1965. 3W. A. Krivsky and R. Schuhmann, Jr.: Trans. TMS-AIME, 1961, vol. 221, pp. 898-904. 4M. F. Ancey-Moret, M. Olette, and F. D. Richardson: Mem. Sci. Rev. Met., 1964, vol. 61, pp. 169-76. 5J . F. Elliott and M. Gleiser: Thermochemistry for Steelmaking, vol. 1. Addison-Wesley, Reading, Mass. 1960. 6 J.Drowart, G. De Maria, and M. G. Ingraham: J. Chem. Phys., 1958, vol. 29, p. 1015. probe of 0.4 mm diam inserted into the open top of the mold. Radioactive sn113, in the form of a small sphere, was gently lowered into the molten tin at point A in Fig. 1 THERMOCOUPLE> WATER ARGON END HEATER QUENCH ARGON Fig. 1—Apparatus for detecting liquid flow. Point A indicates position the tracer was introduced.

Jan 1, 1970

By M. Kitada, U. Kawabe, F. Ishida, T. Doi

The relations between micros tructures and critical current density in transverse magnetic field were experimentally investigated due to each transformation of the 0 to 0' + P" phases at 700' C for superconductmainly examined using replication electron microscopy. The ß' or a precipitates were found to pin down magnetic flux lines in these alloys. The effects of precipitation upon the critical current density were discussed in relation with the size, spacing, and characler of these precipitates. HIGH magnetic field superconductors, such as Nb-Zr, Nb-Ti, and Nb-Zr-Ti alloys, have been recently put to extensive practical use as winding materials for superconducting magnets.13 The critical current density of these hard superconductors under an applied magnetic field is an important characteristic for magnet materials and is very sensitive to metallurgical structure. It is generally known that the critical current density is increased by introducing dislocations and precipitates into a superconductor; that is, dislocations and precipitates are presumed to be barriers that hinder quantized flux lines from moving.4'5 Theoretical6'7 and experimental analyses of the motion of flux lines and the interaction between flux lines and various defects have already been reported by many authors. Metallographic analysis of high magnetic field superconductors such as Nb-Zr and Nb-Ti is difficult, so that no quantitative relationship between microstruc-ture and critical current density has been established yet. In this paper, the effect of precipitation on the critical current density in magnetic field was investigated for two superconducting alloys, Nb-40Zr-10Ti and Nb-5Zr-60Ti. In these alloys the resistive critical field H, at 4.2oK was about 100 kG and the critical current density Jc at 80 kG was of the order of 104 amp per sq cm.13-l5 The superconducting properties were examined in relation to the microstructural changes due to transformation of i) the ß to ß' + ß" phases at 700°C for Nb-40Zr-10Ti alloy and ii) the ß to a + ß phases at 500°C for Nb-5Zr-6OTi alloy. The effect of size, spacing, and character of precipitates on flux line pinning was in particular examined. The microstructures were studied by means of residual resistivity, microhardness, and tensile strength measurements as well as by X-ray diffraction, optical, and replication electron microscopies. I) EXPERIMENTAL PROCEDURE Pure niobium, zirconium, and titanium, in the form of rods 0.8 cm in diam, served as raw materials. Results of chemical analyses of these rods are given in Table I. Ingots of the alloys, 0.4 cm in diam and 3 cm in length, were prepared by means of levitation melting, utilizing a copper mold in an argon-gas atmosphere. Samples from the ingot then were cold-worked by grooved mill to 0.2 cm in diam, heat-treated homogeneously (in the ß phase region) for 5 hr at 1100° in a vacuum of 1 x 106 Torr, and finally cold-drawn to 0.025 cm in diam. For heat treatments, samples were wrapped in niobium foil and sealed in an argon-gas atmosphere in fused quartz capsules. Water quenching was done after each heat treatment. Subsequently H-J, were performed at 4.2° by slowly transporting the current through the samples 4 cm long, under transverse magnetic field, until the least detectable resistive terminal voltage was observed. The resistive critical field H, was taken as the field at which 100 pv appeared at 4.2°K across a sample 3 cm in length, with a current of 5 ma. The critical temperature T, was measured by means of a conventional four-probe resistivity technique and taken as the temperature at which the sample resistance reached one-half of full restoration of the normal-state resistance with a current l ma flowing through a sample 2 cm in length. Precipitates were observed by means of optical microscopy and carbon replication electron microscopy. The etching solution consisted of 5 ml HF, 10 ml H2SO4 10 ml H2O2, and 50 ml H2O, and shadowed carbon replicas were examined in a itachi HU-11 electron microscope operated at 50 kv. X-ray diffraction photographs were taken by a 11.46-cm-diam Debye-Scher-rer camera using copper Ka radiation. The micro-hardness was measured under a load of 200 g using

Jan 1, 1969

(Members are urged to send in for this. column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at the Institute headquarters during the period Sept. 10, 1916 to Oct. 10, 1916. Arthur K. Adams, Chanaral, Chile. C. F. Moore, Salt Lake City, Utah. Hiram W. Belnap, Washington, D. C. L. D. Moore, Providence, R. I. E. A. Bridgman, Seattle, Wash. George A. Morrison, Chicago, Ill. D. W. Buckly, Wallace, Idaho. Pablo Ortega, Havana, Cuba. G. L. Carlisle, Jr., New York, N. Y. L. W. Paige, New York, N. Y. Ernest H. A. Cohen, Johannesburg, So. Africa. Charles Petzel, New York N. Y. A. Faison Dixon, Camp Rio de Oro, Venezuela. C. A. Pierce, Patagonia, Arizona. Charles E. Dutton, Goldfield, Nev. W. E. Pomeroy, El Paso, Texas. D.-F. Hewitt, Washington, D. C. George S. Rice, Washington, D. C. . James E. Howard, Washington, D. C. G. J. Schofield, Seattle, Wash. A. 0. Ihlseng, Joplin, Mo. Warren D. Thompson, New York, N. Y. I. Ishikawa, Niagara Falls, N. Y. M. M. Valerius, Tulsa; Okla. Montrose L. Lee, New York, N. Y. G. B. Waterhouse, Buffalo, N. Y. V. H. McNutt, Billings, Mont. Joel H. Watkins Washington, D. C. Benjamin L. Miller, So. Bethlehem, Pa. H. P. Wherry, Chicago, Ill. Arthur K. Adams has left for Chile, where he will act as geologist for the Andes Copper Co., a subsidiary of the Anaconda copper company.

Jan 10, 1916

By B. C. Allen

Grain-boundary gvoocing was studied irz chronziu?n. molybdenum, tungsten, and the solid-solution alloys, Cr-35Re. Mo-33Re, and W-25Re at 0.6 to 0.9 of the absolute liquidus temperature under an inevt atmosphere , foveign nzetal zlapor, and liquid metal. The controlling mechanism of matter transport was deduced frolr groove size and shape. kinetics of growth, and cotnparisoz with theoretical relatiotzships derived by Mullins. Grooves in chowzizon formed prittzarily by volume diffusion tkrongk kelium or argon at 1 atm pressure and by e1)apovation-condensatiotz in a static vacuum. Groozles in the other nzetals and alloys forrned priniarily by sirface diffusion, the coefficients of which were calculated. Carbon was found to decrease the acti7:ation energy for surface diffusion on molybdenun. Sitrface diffusizities weve sinzilav for iWo-0.0ZC and Mo-33Re. The presence of about 1 -?nm pressure of silver or tin vapor did not affect the neckanis)n of grooz;e formation. In liquid titz or silz:er, pain bolindary gvooves formed by zolume diffusion in the liquid. BASED on theories of ullins," the mechanisms of grain-boundary grooving have been determined for low-melting metals such as copper in an inert atmospheres or in liquid lead.4 The purpose of this investigation was to study grain-boundary grooving in the refractory Group VI-A metals, chromium, molybdenum, and tungsten, and the bcc solid-solution alloys, r-35e, 0-33e,= and -25e,' at 0.6 to 0.9 of included to see whether Mullins' theories were applicable to them as well. EXPERIMENTAL WORK The materials chromium, molybdenum, tungsten, Cr-35Re, Mo-33Re, and W-25Re were in the form of 0.050-cm-thick sheet assaying 99.98 pct or better. The nominal carbon level was generally 30 ppm. The oxygen + nitrogen + hydrogen content was -50 ppm. Mo-33Re and W-25Re were prepared by powder-metallurgy methods and supplied by Chase Brass and Copper Co. The remaining materials were arc-cast. Chromium and Cr-35Re were prepared at Battelle by arc melting, extruding, swaging, and rolling. Mo-0.003C was supplied by Climax Molybdenum Co., and Mo-0.02C and tungsten by Universal Cyclops Corp. As a source of liquid metals, tin and silver granules assaying 99.98 pct were used. Spectrographic analyses indicated the presence of -100 ppm each of iron and silicon. Vacuum melting reduced the combined gas content to c5 ppm (2.60,, 0.9N2, 0.4H2 in tin and l.602, 0.7N2, and c0.04H2 in silver). Specimens were prepared for grain-boundary grooving. Coupons 0.5 by 1.5 cm with a small hole in one end, or substrates 1.5 by 1.5 cm, were cut from sheet. The specimens were annealed in containers of the same material to provide a vapor-solid equilibrium as well as to protect them from gaseous impurities. Outgassing was done at 2 x 10"5 mm for 15 to 30 min at 1150°C for chromium and Cr-35Re, 1750°C for molybdenum and Mo-33Re, and 2600°C for tungsten and W-25Re. Then recrystallization to a stable grain size of about 0.5 mm was accomplished by annealing at least 1 hr at 1600°C for chromium, 1800°C for Cr-35Re, 2350°C for molybdenum, and 2300°C for Mo-33Re in a rhenium-element resistance furnace under 1 atm of static argon or helium. The atmosphere was gettered by tantalum radiation shielding. Tungsten and

Jan 1, 1967

MONDAY, FEB. 17 9.00 A.M. to 9.00 P.M. Registration at Institute Headquarters. 9.00 A.M. Meeting of Committee on Development of the Activities of the Institute, Room 905, 9th Floor. 10.00 A.M. Simultaneous Sessions of Institute of Metals Division, Room 2, 5th floor. Industrial Organization, Room 1, 5th Floor. 12.30 P.M. Luncheon at Headquarters, 5th Floor. 2.00 P.M. to 4.25 P.M. Simultaneous Sessions of Institute of Metals Division, Room 2, 5th Floor. Industrial Organization, Room 1, 5th Floor. Petroleum and Gas, Room 905, .9th Floor. 2.30 P.M. Sightseeing trip by automobile for the ladies. Among the points visited will be: The American Museum of Natural History. The Episcopal Cathedral of St. John the Devine. The Spanish Museum. The American Geographical Society. The American Numismatic Society. The visits will be followed by Tea. 4.30 P.M. Memorial Service to Dr. Rossiter W. Raymond, Auditorium. 8.30 P.M. Smoker, 5th.floor.

Jan 2, 1919

By W. S. Reid

In March, 1938, E. P. Fleming, metallurgist for the American Smelting and Refining Co. inaugurated an investigation into the possibilities of recirculating the gases from Dwight-Lloyd sintering machines operating on lead charge, with the twofold object of concentration of the SO2 content and reduction in volume of total gas produced. The possibility of recovering a commercial grade of SO2 gas from D & L machines operating on lead charge had previously been considered by several investigators. Early History of Recirculation The Selby Smelter Commission Report, published by the Bureau of Mines in 1914, contains a chapter by A. E. Wells regarding results obtained at Selby, wherein some of the richer gas was recirculated through a hood over the pallets. Oldright and Miller of the U. S. Bureau of Mines had also made tests at Trail, B.C., and at Kellogg, Idaho. R. C. Rutherford, while at the Chihuahua, Mexico, Smelter of the American Smelting and Refining Co., in May, 1937, proposed recirculation of D & L gases to decrease the volume of gas handled by the baghouse. At none of these plants, however, was the operation commercialized. In July, 1938, Mr. Fleming, in correspondence with the Selby Plant, inquired regarding the possibility of obtaining 6 pct SO2 gas from the Selby D & L machines. At that time, the writer advised that there was slight possibility of obtaining 6 pct SO2 gas without re- circulation, but believed that it was possible with recirculation, and that experimental work toward that end should be tried at some plant where spare D & L machines were available. The foregoing statement was based on the following information then available— 1. Tests on Selby first-over machines showed 2.28 pct SO2 from first windbox and 1.03 pct SO2 from second windbox, and corresponding figures for second-over charge of 0.81 pct SO2 for first windbox and 0.08 pct SO2 for second windbox. 2. Oldright and Miller (US. Bureau of Mines) in 1932 at Bunker Hill, on 42 in. X 22 ft machines found: a. First-over charge—Maximum SO2 concentration (leaving cake) of 9.5 pct. b. First-over charge—SO2 concentration of over 8 pct from the 4 ft to the 12 ft points beyond the front dead-plate and that the concentration then dropped rapidly. c. That approximately 80 pct of the total sulphur eliminated on the second-over machines occurred during the travel of the pallets from the 1 ft to the 6 ft distances from the dead-plate. d. That approximately 94 pct of the total sulphur eliminated on the second-over machines occurred over the first windox. 3. Oldright and Miller (US. Bureau of Mines) in 1932, at Trail, on 42 in. X 50 ft machines found: a. First-over charge—SO2 varied from 2.0 pct to 5.5 pct (leaving cake) from the 12 ft to 28 ft points from the deadplate. b. That the average SO2 increased from 1.0 pct at 7 ft from dead-plate to maximum of 3.3 pct at 20 ft, then dropped to 1.5 pct at 40 ft. c. That on a 22 ft, second-over machine with an 11 in. bed the SO2 varied from 4.5 pct to 6.5 pct from the 2 ft to the 8 ft points from the dead-plate. d. That on the final roast, the SO2 concentration also varied across the pallets; that is, 2 1/2 pct at the side, increasing to 6.0 pct, 5 in. in, and to 7.0 pct at 10 in. to 20 in. in, then decreased vice versa at the opposite side. e. Concluded that most of the sulphur on a 22 ft machine was removed over the first 7 ft of the first windbox; therefore, they partitioned the first windbox so that the exit gas from the second 4 ft section was returned to the surface of the pallets over the fist 7 ft section, and during a seven-day trial the gas from the 4 ft section averaged 2.4 pct SO2, while the recirculated gas from the first 7 ft section only increased to 3.8 pct SO2. (Excess suction over the 7 ft section to prevent escape of SO2 laden gas from the 4 ft section caused dilution by air.)

Jan 1, 1950

By H. F. Silliman, Daniel R. Hull, Earl W. Palmer

THE brass-rolling industry has not had a great deal of experience with antimony in its product. There have been some recent excursions with antimony as a corrosion inhibitor in tubes, but in sheet brass it has been regarded with apprehension and generally avoided. This is not to say that [ ] contaminations have never occurred, and probably a great many brass mill men have had their own ideas on the effect of such contamination. Our own views were based upon certain experiences some years ago with strip castings that split lengthwise in the early stages of rolling. The nature of this splitting is shown in Fig. I, from a photograph taken in 1922 as a record of 20 bars of 65-35 common brass made with an antimonial brand of copper. These bars were cast 6 ¾ in. wide by 1 in. thick by 45 in. long. In the first pass through the rolls, 19 of the 20 split lengthwise throughout their length, while each half curved outward in a wide arc as it emerged from the rolls. [ ] In those days, if splitting was not a frequent occurrence, it was not unfamiliar. One can recall periods of short duration when large amounts of common brass would behave in this way. There was nothing imaginary about these spells. The affected metal would split lengthwise in the breaking rolls, and no maneuvering of mill practice made any difference. The condition would descend like a plague, demoralize the mill for several days, and disappear. It is doubtful if anyone knew the cause-however many explanations may have been current. In 1921 a quantity of split brass was traced to the use of fired small-arms

Jan 1, 1943

?ADAIR, ARTHUR C., Corp 4th Co., 1st. Training Bat., 154th Depot Brigade. ADAMS, HENRY, Major: Chemical Warfare Service. ARLUCK, A. A Headquarters, 1st Corps of Artillery. ASKIN, THOMAS B. H Ensign. BANKS, H. R., 2d Lieut Canadian Engineers. BAYLESS, G. E. S Supply Dept. U. S. Submarine Base. BELL, L. R Co. C, 302d Engineers. BELLIS, ARTHUR E., Capt Ordnance Reserve Corps. I BIRRETT, HOWARD, Lieut., Aviation Section, U. S. Signal Corps, Ellington Field. BOISE, PAUL T 2d Regiment, 24th Squadron. ?BRADLEY, CLARENCE I Convois Automobile Section 585. BROWN, GEORGE M Co. G lot Engineer Replacement Regiment. BUCKINGHAM, ALBERT U. S. S. " Coronet," S. P. 194, Section Base No. 7. BURNS J. J Co. 1-B, E. R. O. T. C. BURT, Co. B, let Engineers Replacement Regiment. ||BYERS, WHEATON B., 2d Lieut Ordnance Dept. CANTON, WILLIAM R., Sgt Headquarters Co., 80th F. A. CARSON, JOSEPH A., Capt A.S. S. R. C.' CHAPMAN, LEWIS C. Corp 29th engineers. CHETNEY, P. C., 2d Lieut 15th Bat. Headquarters Co. CHEVRILLON Louis French Red Cross. CHIDESTER, W. B., 1st Lieut 24th Machine Gun Bat. CHURCH, JOHN L., Capt 308th Engineers. CLAGHORN, D. MONTGOMERY, 1st Lieut 45th Engineers. CLAQHORN, JAMES L., Lieut Aviation Section, Signal Corps. CLARKE, ALEXANDER F U. S. Naval Aviation Service. COMINS, WALDO H. Ca t 41st Co., 164th Depot Brigade. COOK, FREDERICK A., Capt., Engineer Reserve Corps, Asst. to Div. Engr. 79th Division. COOPER, CLAUDE H. Capt C. A. R. C., 50th Artillery. COPELAND, N. R., Lieut. ||CORBY H.. G., 1st Lieut Co. D, 109th Supply Train. CORSA, BEAN, Capt Co. D, 612th Engineers. CORTESE, EMILIO Italian Army. COULDREY PAUL S., Corp British Expeditionary Forces. || CRAGIN, RODNEY S Co. E, 115th Engineers. CURRIE, JOHN M., Ca t Royal Engineers. || CUTTING, G. W., 2d Lieut U. S. Reserves, Field Artillery. V DARRINGTON, PAUL N., 1st Lieut U. S. Infantry. DAVIS, ANGUS W., Lieut-Col British Expeditionary Forces. || DAVIS, THORNTON, 1st Lieut 13th Field Artillery. ELAND, FREDERICK A., Major Engineer Reserve Corps. DOUGLAS, JAMES $ American Red Cross. DOVE, D. R., Candidate 21st Training Battery, F. A. C. O. T. C. Dover JAMES J 6th Co. C. B. DOWS, DAVID,Capt Coast Artillery, Officers Reserve Corps. || DRAKE, M. 6., 2d Lieut Headquarters Co., 325th Infantry. I || EMMERSON, E. Roy British Navy. EVERIT, RICHARD STURTEVANT Heavy Artillery Officers' Training Camp.

Jan 1, 1923

By AIME AIME

THE American Institute of Mining and Metallurgical Engineers will hold its annual meeting in New York City, Feb. 9-12. The technical sessions, excepting the Sunday afternoon and evening sessions of the Mineral Industry Education Division (see the M.I.E.D. program) will be held in the Engineering Societies Building. The "All-Institute" luncheon on Monday will be at the Commodore Hotel; the Annual Banquet and President's Reception, the Smoker, and the Informal Dance will be at the Waldorf Astoria Hotel. The dinners of the Petroleum Division and the Institute of Metals Division will be at the Roosevelt Hotel.

Jan 1, 1942

By A. C. Fraker, H. H. Stadelmaier

In the systems Mo-Fe-C, Mo-Co-C, and Mo-Ni-C the phase boumdaries of the cubic Ij carbides were determined at 1000°C and the variation of the lattice parameter with composition was measured. In the system Mo-Fe-C a single ternary carbide, Mo3Fe3C, was observed. In Mo-Co-C and Mo-Ni-C two new n phases of the type M12C were found: Mo6C06C and Mo6Ni6C. At 1000°C they coexist with the M6C phases MO3-4,CO3-2C and Mo3-4Ni3-2C, respectively. Mo3C03C and Mo4C02C are not separate phases but parts of a single M6C phase region, and the same is true of Mo3Ni3C and Mo4Ni2C. THE n carbide structure type has been known since it was determined by westgren' in 1933, yet reliable information on phase compositions of this type is ap-parently scarce. The following selection of suggested formulas illustrates the extent of the confusion con-cerning compositions: W2-3Fe4-3C,1W6Fe6C,2 W2_4Fe4-2C,3 (W,Fe)6C,4 Tj.-W4Co2C and nz-W6Co6C,5 n1-W3Co3C and n2-w4Co2C,5 W3C03C and w6Co3C2,7 MO3Fe3C,8n2-M04Fe2C,9 (MO,Fe)6C,4 MO3CO3C,8 n2-MO4CO2C.9 Many of these compositions obviously overlap, some disagree in carbon content. The use of the designations 77, and n2 is not consistent. There is uncertainty whether two carbides M6C coexist or whether there is only one M6C with a wide range of substitution of one metal for the other. The existence of M12C seems questionable altogether if one ignores the results of a neutron diffraction study of W6Fe6C supporting that particular metal to carbon ratio.'' More reliable information is available for the iso-typic oxides studied by Nevitt,11 Nevitt, Downey, and orris," and Meussner and carpenter.l3 That n car-bides and oxides are structurally identical, particularly with respect to the location of the metalloid atom, has been demonstrated clearly by Stadelmaier and Meussner14 and also by Parthe, Jeitschko, and sadagopan.15 Therefore the present paper, which attempts to establish the phase boundaries of n defini-tively for three carbon systems, has implications for the whole family of filled Ti2Ni types. EXPERIMENTAL PROCEDURE The samples were prepared in two stages. Pellets weighing 3 g were compacted from powders of the elements and presintered in a closed tube of fused silica that had been evacuated to lO-4 mm Hg. This was fol- lowed by arc melting the sintered samples under argon. Remelting the button once was sufficient to produce homogeneous specimens. The metal powders had the following minimum purities in wt pct: molybdenum 99.5, iron 99.0, cobalt 99.7, nickel 99.9, graphite 99.94. Carbon determinations by the gas volumetric method were obtained from thirty-one of the one hundred samples in the annealed condition. They were limited to compositions that were critical to placing a boundary line in the isothermal sections. The carbon losses were comparatively low and averaged less than 1.5 at. pct. For annealing, the samples were sealed in tubes of fused silica evacuated to 10-4 mm Hg. The annealing schedule was 20 hr at 1250°C followed by 150 hr at 1000" ±10°C. For the water quench the silica glass tubes were broken mechanically to speed the quench. The specimens were examined in the as-cast and annealed condition by standard metallographic techniques. Some of the as-cast and all annealed samples were studied by X-ray diffraction using a 114.6-mm powder camera with filtered Co radiation. The lattice parameters of the n phases were determined by graphic extrapolation to 8 = 90 deg on a plot against sin2 8. It is estimated that the maximum error in the lattice parameters is ±0.002A.. The phase fields were determined by the disappearing phase method, relying on X-rays for phase identification and on microscopy to detect small amounts of a phase. RESULTS Pertinent information on the binary side diagrams has been summarized by Hansen and Anderko16 and Elliott17 and will not be discussed further. Photomicrographs documenting the equilibria at 1000°C have been selected to avoid redundancy due to the similarity of the three systems. Thus there will be only one picture showing an equilibrium with Mo2C, and so forth. Molybdenum-Iron-Carbon. An isothermal section of most of the Mo-Fe-C system at 1000°C is shown in Fig. 1. No attempt has been made to distinguish between a and y iron or to determine their phase boundaries. A conspicuous absence is the phase Fe2 1Mo2C6 with the Cr23C6 structure, supporting the suggestion by Krainer4 that it decomposes by annealing at high temperatures. The only ternary phase is found in a narrow range around Mo3Fe3C (MO43Fe43C14). A microstructure with a two-phase mixture of Mo + n is seen in Fig. 2. The variation of the lattice parameter of n with the estimated composition is shown in in Table IA. The phase diagram does not agree with the results of Kuo9 who reported n2-Mo4Fe2C. Our lattice parameter Varies from 11.095A at the iron-rich end to 11.140Å at the molybdenum-richoend of the phase field whereas Kuo9reported 11.26Å for Mo4Fe2C. We are in agreement with the older work

Jan 1, 1970

By D. G. Westlake

Polycrystalline tensile specimens of various Zr-0-H alloys have been tested at 298°, 178°, and 77°K. Solute oxygen and hydride precipitates in quenched alloys made individual contributions to the yield strength at 0.2 pct strain which combined to produce a resultant strength increment, a,., Ductility changes which were ohserved can he interpreted in terms of the various oxygen and hydrogen concentrations, testing tem -peratures, and dispositions of the hydride. ADDITIONS of oxygen in solid solution were known to increase the yield and tensile strengths of polycrystalline zirconium as early as 1951.' More recently, the critical resolved shear stress (CRSS) for prism slip in zirconium single crystals was also shown to be affected by the solute oxygen impurity.' This latter work also demonstrated that large increments of strength could be contributed by the finely dispersed zirconium hydride precipitates that are present in quenched Zr-H alloys.3 It was concluded that the combined strengthening due to alloying could be expressed by where to is the increase in the CRSS due to solute oxygen alone and TH is the increase due to finely dispersed hydride precipitates. Eq. [I] is analogous to one used to express the combined strengthening effects of work hardening and neutron radiation damage.4 Eq. [1] was verified only indirectly and for only small amounts of the impurities—up to 0.14 at. pct 0 and 0.63 at. pct H. The present investigation was undertaken to obtain a more direct verification of the validity of the form of Eq. [1] for this system and also to determine the combined effects of oxygen and finely dispersed hydride precipitates on the tensile strength and ductility of polycrystalline zirconium. EXPERIMENTAL PROCEDURE Tensile specimens were machined from the same rolled billet of Kroll zirconium used in the earlier study.' These measured 38 by 4.7 by 0.5 mm and had 10-mm gage lengths which were 2.8 by 0.5 mm. Each specimen was ß-annealed in vacuo at 1173°K for 15.5 hr and a-annealed at 1073°K for 4 hr to D. G. WESTLAKE, Member AIME, is Associate Metal l ur-gist, Metallurgy Division, Argonne National Laboratory, Argonne, III. Manuscript submitted July 17, 1964. IMD______________ give an equiaxed structure with grain diameters averaging 0.06 mm. Oxygen was added by allowing the metal to react with a known quantity of oxygen during the 0 anneal and known quantities of hydrogen were added during the a anneal. Each alloy was encapsulated in Pyrex under vacuum, annealed at 873°K for 4 hr, quenched into ice water, and polished by immersion in a solution of 46.75 vol pct H2O, 46.75 vol pct concentrated HNO3, and 6.5 vol pct HF (49 pct) at 298°K. Special heat treatments given to a few specimens are described in the results below. Tensile tests were done on an Instron machine and were begun within 20 min after the quench, except where specified otherwise. Tests at 298°K were in air, at 178°K in acetone, and at 77°K in liquid nitrogen. All tests were at a strain rate of 8x sec-1. RESULTS AND DISCUSSION Yield Stress at 298°K. The compositions of alloys and the corresponding yield stresses (0.2 pct strain) are given in Table I. A plot of the yield stresses of the oxygen alloys, A, B, C, and D, indicates that varies linearly with CO1/2, where Co is the oxygen concentration, Fig. 1. This is in accord with Fleischer's6 theory for solution strengthening if the oxygen atoms do not cluster, or the cluster size remains constant with increasing oxygen concentration. In Fig. 1, it appears that if one could prepare some oxygen-free zirconium its yield stress would be very low. Therefore, we shall assume that for the oxygen alloys is equivalent to O0, the strength increment contributed by the presence of oxygen. The relationship between0.2and Co is expressed by 0.2 = 31.3 CO1/2, when the yield stress is in kg per sq mm and the concentration is in at. pct. Each of the hydrogen alloys, Al, A2, A3, and A4, contained 0.081 at. pct 0 as an impurity. In Fig. 1, it appears that this small amount of oxygen makes a significant contribution to the strength which cannot be ignored when we evaluate the contribution of the finely dispersed hydride. Let us assume the validity of the following equation: a0.2 = (a2o+a2R)1/2 [2] which is analogous to Eq. [I] for single crystals, and calculate values of UH for the hydrogen alloys by using the experimental values of 0.2 and o (0.081 at. pct) = 8.9 kg per sq mm. For 0.36 at. pct H, oH = 6.47; for 0.72 at. pct H, OH = 11.30; for 2.16 at. pct H, OH = 19.4; and for 3.60 at. pct H,

Jan 1, 1965

By D. Turnbull, J. C. Fisher

ACCORDING to the "reaction-path" modell,2 of martensite nucleation, the shear angle of the embryonic martensite plate must be treated as a variable, and included in any calculation of nucleus critical size. Also, as can be deduced from this model, the interfacial free energy between austenite and martensite does not reach its final value until the shear is completed. It is zero for zero shear angle. However, in order to account for the kinetics of the martensite transformation, some sort of interfacial energy barrier appears to be necessary even with the reaction-path model, for otherwise the volume and the energy of formation of the critical size nucleus both collapse to zero.3 Cohen independently suggested that surface energy could be incorporated into the reaction-path model, with the overall free energy of a martensite embryo being a function of its volume and shear angle.' It is possible to estimate the energy associated with the formation of a critical-size martensite nucleus starting with the reaction-path model and including a surface free-energy barrier. As the dependence of interfacial free energy upon shear angle is unknown, a simple type of dependence will be assumed, with the belief that the true dependence would not lead to appreciably different results. Consider the work required to form a lenticular martensite plate with radius r, thickness t, and shear angle 8. There are three contributions; one being the interfacial free energy, one being the free energy change in the martensite plate, and one being the free energy increase in the surrounding austenite. The interfacial free energy u is assumed to depend upon the shear angle 0 according to the relationship s=s0(?/?0)n [1] where 8, is the equilibrium shear angle and n is an exponent that may lie in the range 0 n 2. The work required to form the interfaces of a martensite plate then is W. = 2pr² s0(?/?0)n [2] The free energy change per unit volume of martensite is composed of two parts, one the ordinary volume free energy ?f1. which is negative, and the other the elastic strain energy G?m²/2, where G is the shear modulus and 7, the shear strain relative to the martensite structure. This expression for the strain energy is valid only when the shear strain ym, is sufficiently small that the martensite is within its linear elastic range. There is no doubt that ym, lies beyond the linear elastic range for embryos that are considerably subcritical. However, for critical nuclei it will be shown that ym, is 1.5 pct or less, within the linear elastic range of martensite. For embryos of nearly critical size, then, the strain energy of the martensite is correctly given by G?m²/2. The shear strain in the martensite is ym, = 8, — 8, and the work required to form the strained martensite is Wm --= (pr²t/2) [?fv + G(?O - ?)²/2] [3] The free energy change in the austenite is entirely that due to elastic distortion. The elastic strain is not uniformly distributed in the austenite, being large near the martensite plate and small elsewhere. Approximately, however, the energy corresponds to a uniform shear strain ya= (?t/2)/r [4] throughout the volume 4pr³/3 surrounding the plate. The work required to strain the surrounding austenite then is Wa = (4pr³/3) (G?a²/2) = (G?²/6) prt² [51 For simplicity, the same shear modulus G is assumed for each structure. The total free energy for forming a plate then is W = W3 + Wm + Wa. = 2pr² s0 (?/p?0)n + (pr²t/2) [?fr+G(?0-?)²/2] + (G?²6) prt2 [6] This expression is correct for nuclei and for embryos of nearly critical size, where, as will be shown, the strain energy in the martensite is correctly given by the expression G (? — ?)². Having W as a function of r, t, and 8, as in Eq. 6, there is a saddle-point where W has a stationary value, W subsequently decreasing indefinitely as the nucleus volume increases along the reaction path. The stationary value of W is the energy of the critical nucleus. The critical nucleus has radius, thickness, and shear angle such that ?W/?r - awlat: = ?W/?p? = 0. Performing these differentiations and calculating the critical nucleus energy, W* = [8192p(G?/6)²;s/27 ?fv4] [7] where a= (?/?0)3n+1[l +G(8"-8)'/2af.]' [7a] and where 8 is to be determined from the equation (1 + 3n/4) + G8(6O - (9)/[Af. +G(6>o-6>)72] = 0 [8] For ?f, near —200 cal per mol or —10" ergs per cc, and 8, near 1/6, as for iron-base alloys, Eq. 8 gives ?0 - ? ~ - (4 + 3n) ?f1./4G0O [9] as the difference between the equilibrium shear angle and the actual shear angle for a critical nu-

Jan 1, 1954

By H. A. MEGRAW

THE meeting of the A. I. M. E. at Wilkes-Barre, Pa., Sept. 12 to 15, inclusive, celebrated the fiftieth anniversary of the Institute. It was at Wilkes-Barre, in 1871, that the foundation was laid for the great institution that now includes in its roster the greatest names. in mining engineering in every civilized country of the world. The founders of the Institute, with rare prescience, established a common ground upon which all mining engineers, whatever particular branch they might consider most pertinent, could stand securely, assured of a deep-seated interest from their brethren similarly minded in other localities. So wise and clear was the vision of the founders that every engineer connected with mining has found it beneficial, not to say indispensable, to maintain his connection with the Institute and to increase his technical enthusiasm through the medium of the valuable technical publications. The little coterie of 1871 has grown to a strong body of more than 10,000 members in 1921, reflecting the glory of the founders in the record of the accomplishments written on the pages of the fifty years of the

Jan 1, 1921