Search Documents

By L. Ibagos S., T. Balberyszski

The volumetric flow rate and the initial concentration of the copper sulfate solution influence the rate of reaction and, hence, the precipitation efficiency in a continuous launder cementation system. Using a model of such a system it was found that the precipitation efficiency is related to the two process parameters by the approximate expression [ log [1-n] = -[0.072 co 2.91 e – 0.511c o Q 1.15 ] N Q] where c is the initial concentration, Q, is the volumetric flow rate and N is the number of launders in the system. This expression agrees with an equation developed for the rate of the cementation process if it is assumed that the exponential factor represents the change in the surface area with concentration and the exponents 2.91-and 1.15 relate the hydrodynamic conditions and the surface concentration to co and Q. The experimental results are used to determine the values of a Precipitation Coefficient for any volumentric flow rate and initial concentration of solution. Knowing the Precipitation Coefficient, the total volume of launders that will result in a given precipitation efficiency can be calculated. It is established that maximum precipitation efficiencies are obtained for initial concentrations between 6.0 and 7.0 gpl and volumetric flow rates of approximately 350 m3 /hr Good agreement between calculated and actual launder volumes is obtained for a number of industrial operations for which a comparison is made.

Jan 1, 1973

By P. H. Dudley

A quarter of a century of service of steel rails on our oldest railroads, many of which have changed their standard sections three or four times, has furnished, and is furnishing, excellent opportunities to study their wear and behavior in the track. Such experience is valuable for the design of new sections, now required to meet the constantly increasing severity of railroad service. Before presenting the new sections for consideration, I will briefly call attention to some features of past experience. For convenience of study, rails may be separated according to their weight and height into four groups, viz.: 1. Hails weighing per yard from 52 to 60 pounds, and 34 to 4 inches high. 2. " " " " " 60 " 72 " " 46 to 44 " " 3. " " " " " 72 " 90 ' 41/8 to 5 4. " " " " " 85 or more " " over 5 " I Experience in this country is confined mainly to sections in groups Nos. 1, 2 and 3. • During the past few years I have had the opportunity to run my car over many thousands of miles of railway laid with the principal sections in use, and to obtain diagrams showing their deflections, permanent set, and, in a great measure, their manner of wear. The First Group.—The first steel rails imported, and those manufactured here, were light sections—included in the first group—and many of them, being rolled in rolls used for rolling iron sections, have pear-shaped heads, 2 3/8 to 2 1/2 inches wide, the base being heavy and from 1/4 to 1/2 inch narrower than the height. These rails were laid upon ties of solid timber, at least 8 inches face, spaced 2 feet from center to center. The moments of inertia of these rails were low, only ranging from 8 for the lightest sections to 12 for the heaviest. The deflections were, of course, great; but the quality of the metal was excellent. It was physically hard and

Jan 1, 1890

By Theron Wasson

Michigan produced 16,637,000 bbl. in 1937. This makes it a record year in the history of Michigan's oil industry. During the year 953 wells were completed; 779 within the limits of established fields and 174 wildcats; 616 new oil wells, 68 gas wells and 269 dry holes. Table 1 has been arranged in alphabetical order of field names. Production figures for 1936 have been corrected because December figures were estimated. In this year's summary, December production is based on actual reports. The Leaton and Mt. Pleasant fields have been re-defined. Mt. Pleasant production north of the south line of Denver township, Isabella County, has been included with Leaton in accordance with usual practice in Michigan. The locations of fields discovered since the last map was published1 are shown in Fig. 1. Activity during 1937 Buckeye Field.—The Buckeye field of Gladwin County was the center of greatest activity during the year and was responsible for the increase of 4,700,000 bbl. over the state total for 1936. Buckeye produced 6,428,-000 bbl. in 1937. In this field 328 producing wells were completed during the year—over one-half the oil producers drilled in the state. Buckeye was subject to voluntary and cooperative proration from April 1 to the end of the year. Other pools of the state were not prorated. The new production at Buckeye is from porous Dundee limestone of Devonian age, similar to the older fields. Other New Fields.—The Sherman field was second in importance as a source of new production, with a total of 1,532,000 bbl. Salem township, Allegan County, on the southwest side of the Michigan Basin, was developed during the year. Production at Salem is from the Traverse limestone at a depth of 1600 ft., and 52 producing wells have been drilled in this pool. Other active pools were Clayton and Adams townships, Arenac County. The Bentley pool, discovered in October 1937 southeast of

Jan 1, 1938

By John Fritz

TROUGH it is not a condition of the Award, the fact is that the John Fritz Medal never has been given to an engineer who had not already received one or more similar awards. This "medal for medalists," on the evening of April 20, was presented to Daniel C. Jackling at a special dinner held at the Union League Club in New York. The citation read "For notable industrial achievement in initiating mass production of copper from low-grade ores through the application of engineering principles." The present award recognizes the same accomplishment-the launching and guiding to the port of marvelous success of the Utah Copper Co., first of the so-called "Porphyries"-as did the award of the William Lawrence Saunders Gold Medal by the A.I.M.E. in 1930, and before that the Award of the Gold Medal of the Mining and Metallurgical Society of America in 1926. Following the custom a biography of the Medalist had been published in a small pamphlet as a supplement to the John Fritz Medal Book. T. A. Rickard was the au¬thor of the sketch of Mr. Jackling, an innovation being the placing of a copy of the booklet at the place of each of the diners. The committee in charge of the dinner consisted of two past-presidents: R. E. Tally, of the A.I.M.E., who was chairman; Bancroft Gherardi, of the A.I.E.E.; and Thaddeus Merriman, director of the A. S. C. E., the John Fritz Medal being a joint award of the four societies. Frederick M. Becket, President of the A.I.M.E., as chairman for the occasion, briefly stated the purpose of the dinner. He stressed his satisfaction that the award was symbolic of the cooperative professional activities of the four great national organizations of engineers. He introduced Francis Lee Stuart, past-president of the A.S.C.E. and now chairman of the John Fritz Medal Board of Award. Mr. Stuart outlined the history and purpose of the Medal established in 1902 in memory of John Fritz, of Bethlehem, Pa., one of the great pioneers of America's iron and steel industry, metallurgist, and president of the A.I.M.E. in 1894. Mr. Stuart called the roll of former John Fritz Medalists, three of whom, Ralph Modjeski, J. Waldo Smith, and Ambrose Swasey, were present to do honor to Mr. Jackling. He then introduced George Otis Smith, whose privilege it was to present the Medalist for 1933. Dr. Smith was the senior of the four A.I.M.E. representatives on the Board that last year selected Mr. Jackling for the honor. His speech follows in full.

Jan 1, 1933

In accordance with the usual custom, manuscripts to be presented at the next meeting of the Institute must be in the hands of the, Secretary before July 1, 1917. Manuscripts to be properly distributed in advance of the meeting must be in the hands of the Secretary before June 1, 1917. At the last meeting of the Institute 45 papers were presented, and 42 of them were actively discussed. This experience makes us believe that advance distribution is the best possible means of getting a good discussion of papers and of securing for them the interest of the members of the profession. It will be impossible, however, to give the papers proper distribution if they bare not received before June 1, 1917.

Jan 4, 1917

By H. H. Hausner, S. Storchheim, J. L. Zambrow

The solid state bonding of aluminum to nickel was studied as a function of temperature, pressure, and time at pressure. The initial results indicated that as the reaction conditions were varied, marked changes in tensile strength occurred. Plots of the log penetration coefficient vs the reciprocal of absolute temperature for various isobars were straight lines displaced from each other. THE techniques of bonding different metals to A each other include brazing, welding, welding by application of a molten phase, and solid state welding without any molten phase present. This last technique, the pressing of metals either at room temperature or at some temperature below the melting point of the metals to be joined, seems to offer interesting possibilities for bonding purposes. However, this technique has not been completely investigated, and very little is known about the diffusion phenomena which occur during solid state welding. Some previous work on the effect of pressure on diffusion1 was inconclusive. This paper is concerned with an investigation regarding the effect that the processing variables, such as pressure, temperature, and time at pressure, have in solid state bonding. The tests were made with aluminum and nickel and special emphasis was given to the strength of the bond between these two metals and to the intermetallic penetration rate during the bonding process. It seems that the effect of pressure on the intermetallic penetration is of particular importance for practical purposes and this effect was therefore studied in detail. Procedure Apparatus: The means of solid state bonding used for this study was that of the hot-pressing technique. This method requires the equipment pictured in Fig. 1 and involved the following procedure. The two metals to be bonded were placed in an aquadag lubricated 18-4-1 tool steel die, 16 in. high by 1.440 in. ID, between punches of 1.366 in. diameter made of the same material. A thermocouple

Jan 1, 1955

By Shun-ichi Satoh

In the previous paper, the writer indicated that the arc welding of cast iron is practicable only when barium carbonate is used to retard the fusion of electrodes. Later, he tested the effects of 48 other elements, to discover the cause of their retarding action. Wrought-iron bars 33 cm. long and 0.53 cm. dia. were used as electrodes. The chemical analysis of the original electrode is given in Table 1. Table 1.—Analysis of Electrode Per Cent. Carbon.................................................. 0.045 Silicon................................................... 0.028 Manganese....................................... Trace Phosphorus.............................................. 0.047 Sulfur................................................... 0.008 Each of the bars was wound with a twine of asbestos (1 mm. dia., weighing 0.5 g.) and then was coated with a mixture of equal quantities of graphite and carborundum and one of the compounds listed in the second column of Table 2. The method used in coating was as follows: The mixtures were reduced to paste by adding to them a solution of water glass (1:3); they were next put in a glass tube of 8 mm. inner diameter, with funnel-shaped mouth (the same tube shown in the previous paper); then the bars were passed through the tube so that the mixtures were coated on them. The glass tube was used only as a means of making the diameters of all coated bars exactly 8 millimeters. The cast iron was deposited on the steel plates by connecting the electrodes first to the positive and then to the negative pole of the generator. The figures representing the time, voltage, amperes and energy required to melt each electrode are given in Table 2. They are arranged in the order of the atomic weights of the elements contained in the coatings. In Figs. 1 to 4, which show respectively the time, current, voltage and energy required in this operation, the abscissas indicate the atomic weights of the elements contained in the coatings, and the ordinates

Jan 1, 1929

By N. Brown

IT has been observed that a hexagonal-close-packed crystal will undergo the same macroscopic displacements as an isotropic material if the basal plane is perpendicular to the axis of twist.&apos; Other orientations may produce both bending and twisting, but this analysis will be confined to pure torsion of a right circular cylinder. The z axis, the axis of twist, and the specimen axis are coincident. The displacements are given by Uq = rz, Ur = Uz = 0 [1] where 4 is the angle of twist per unit length. This requires rotational slip, as discussed by Frank&apos; and Wilman, which may be observed readily. The relative rotation of adjoining slip planes is simply produced by a movement of a planar grid of screw dislocations."." The screw dislocations are of the same sign and they move radially inward. For hexagonal-close-packed metals, the grid is hexagonal and the screw dislocations lie in the < 2110 > directions. The displacement of a point is the resultant of two displacements produced by intersecting screws sweeping over the point. The dislocations must pass over the point (r, o) in such a manner that its resultant displacement corresponds to the observed macroscopic displacement. If 6&apos; is measured from the [1010] direction, then for 0 < ? < ~/3, only the [1210] and 121101 type screw dislocations are needed to produce the required displacement. If n1 screws of type [1210] and n2 of type [2110] pass over a point, then, in order that Ur = 0 n, sin ? - n2 sin (/3 — 6&apos;) = 0. [2] If the tangential displacement is to be independent of 0, then n1 cos ? + n2cos (/3 —?) = N [3] where N is independent of ? and thus depends only on r. Nb is the tangential displacement where b is the Burgers vector. Since U? is a linear function of r, then N must be a linear function of r. If a2 is the outer radius and a, is the inner radius to which the plastic deformation has extended, then N = Nm2 r-a1 [4] This function meets the conditions that at

Jan 1, 1956

By T. I. Moore, L. A. Painter

THE electrolytic zinc plant of the American Zinc Co. of Illinois was described by Davidson&apos; in 1944. Since then, improvements as well as expansion of the plant facilities have been made. In order to increase the production of high grade zinc which was needed for war purposes, an expansion program designed to double the slab zinc capacity was started in 1942 and completed in March 1943. This expansion was propagated by a contract between the American Zinc Co. of Ill. and the Defense Plant Corp. The contract included the facilities of the Fairmont City, Ill., property of the American Zinc Co., where a suspension-type roaster with contact acid plant, cadmium distillation furnace, Waelz oxide and densifying plant, and horizontal retort furnaces were installed. The expanded Monsanto, Ill., plant and the additional facilities of&apos; the Fairmont plant were designed to integrate the metallurgical treatment of zinc concentrates for the production of special high grade zinc at Monsanto with the production of acid, cadmium, high grade zinc from furnace skimmings and the Waelz treatment of leach residue at Fairmont. In general, the original flowsheet was not changed, except for the addition of the filtering, drying and reclaiming of leach residue, and the treatment of purification cake for the recovery of copper, cadmium sponge, and zinc. Fig. 1 is a flow diagram of present operations. The original plant facilities, desi-gned for 50 tons daily production of slab zinc, had some units which were more than adequate. Therefore, in expanding the facilities to 100 tons per day, it was not necessary to double all operating components. Table I gives the comparison of the changes made in the unit operating components for the original facilities, 1941, the 1943 expansion, and the 1951 facilities. During the past 11 years a number of improvenients have been made resulting in: 1—an increase in slab production, 2—higher recoveries on the calcine treated, 3—better quality of slab zinc produced, 4—higher current efficiencies, and 5—less man hours Table I. Changes in Operating Facilities Operating Unit 1941 1943 1951 Calcine unloading (pneumatic), 10 tons per hr 12 calcine unloading track hpr. and elev., 60 tons per hr 1 Calcine storage, tons 1,000 2,000 2,000 Leach tanks, 35 vol. tons. No. 3 5 6 slurry mixing 6x6 ft stainless tank, No. 1 Ball mill. 4.5 rt x 16 in. conical. No. 1 CLassifier duplex, No. 1 1 Thickeners. 50 it diam. No. 2 9 2 Filter thickeners, sq ft &apos;-- Moore filters, sq ft 5.760 11,520 Drum filters, 10 ft diam x 16 ft, No. 3 3 Rotary arlers, No. 1 2 1st stage Cu-As purificatlon tank. 90 vol. tons, No. 3 Solution heaters, No. 3 Filter press, 30x30 bronze, No. 4 Zinc dust purification tanks, 45 vol tons. No. 3 5 4 Filter press, 36x36 bronze, No. 3 5 3 Cadmium recovery plant: Process tank. No. 5 2 Cake roaster, 20 ft diam x 4 hearth. No. 1 Filter press, 24x24, No. 4 1 Sponge wash box, 4x6 ft, No. 1 Evaporative cooling unit (vacuum), No. 1 Purified storage tank, vol. tons 400 400 400 Cell acid storage, vol. tons 400 400 400 Electrolytic cells, No. 180 372 372 Cell room ventilation, cu ft per min 35,000 125,000 125,000 Cell cooling water. gal per min 1,500 2,300 2,300 Deep well 16 in. x 95 ft, 1500 gal per min, No. 2 3 3 Melting and casting furnace, 130 ton. No. I Furnace fume scrubber unit, No. 1 Dross drums, No. 2 Dross roaster, 8 ft diam x 8 hearth, No. 1 Electrolysis power conversion, kw 6,250 23,750 23,750 Power transformers, 13,800/440, kva 1,000 1,500 2,000 Steam boilers fire tube, 15 psi, lb per hr 12,000 18,000 18,000 Steam boilers water tube. 125 psi, Ib per hr 30,000 Air compressor, 2 stage. 300 cu ft per min. 100 psi, No. 1 2 Air compressor, 1 stage, 300 cu ft per min, 20 psi, No. 1 Vacuum pumps, 18x7, 720 cu ft per day, No. - - . Vacuum pumps, 24x11, 1.633 cu ft per day, No. 3 3 Building area, sq ft 60,854 113,568 115,000 per ton of metal produced. In the summer of 1944, the "reverse" leaching process was placed in operation and since it has been described,&apos; no further description will be given. Other facilities and changes which have contributed to the process improvements were the scrubbing of fume from the melting and

Jan 1, 1953

By W. T. Isbell, Carleton C. Long

Zinc recovery from lead blast-furnace slags has heretofore been an indirect process, involving, first, the fuming off and collecting of an impure zinc oxide, and second, the reduction of the zinc portion of this oxide to metal either by electrolytic or pyrolytic means. (In a variation of this process, blue powder is the intermediate product rather than zinc oxide fume.) In 1940, W. T. Isbell proposed that molten slag from the lead blast furnace or stock-pile slag melted down in a blast or cupola-type furnace be charged directly into an airtight container (i.e., furnace) provided with means to heat further the slag by passage of electric current and means to introduce the carbon (coke) necessary to reduce the ZnO constituent of the slag to zinc as a zinc vapor and CO. He also proposed that the zinc vapors so obtained be condensed in a Weaton-Najariant internal condenser directly connected to the proposed furnace. It was thought that the Weaton-Najarian condenser could liquefy zinc vapor from lean mixtures of vapor and noncondensable gases. Such condensers have been in commercial use! since 1936 at Josephtown smelter, where the source of zinc vapor is a column of coke and zinc-bearing sinter electrically heated (charge resistor). Condenser output when supplied with vapor-gas mixtures containing approximately 45 per cent zinc and 55 per cent noncondensable gases, varies from 18 to 30 tons of slab zinc per day per condenser, depending upon the heat-transfer area (length) of the condenser and the volume of vapor (furnace size) fed to it. Lead-smelting operations at the St. Joseph Lead Company&apos;s plant at Hercu-laneum, Mo., produce a slag containing 12 to 16 per cent zinc. For several years this slag has been stock-piled with the object of recovering the zinc values if and when a commercial method was invented. Evaluation of the possibilities of the proposed method was made by pilot-plant operation at Josephtown. The first plant, designed in 1940 and operated in early 1941, consisted of a single-phase, two-electrode furnace. The evolved vapors were burned. Electrical characteiistics of the molten slag, power requirements, coke requirements, and extent of zinc elimination indicated the feasibility of the proposed method. In the latter part of 1941 a second pilot furnace was constructed, to which "was attached a small (6 ft. long) Weaton-Najarian condenser in order to develop an over-all picture of zinc-in-slag to zinc-in-slabs. This furnace was operated in the early part of 1942 and yielded such promising results that a decision was made to design- and construct a commercial furnace. Feed for the pilot-plant furnaces was granulated slag. A suitable deduction (300 to 350 kw-hr. per ton slag) was calculated in estimating power require-

Jan 1, 1944

By N. A. Gokcen, M. Ohtani

Thermodynamic intevaction pararnetevs of elements E2(2), for dilute binary solutions of a component "2" in liquid iron, i.e., E(22) = 9 In f2/?N2 where f2 is the activity coefficient and N2 the mole fraction, and E(3) 2 = In f2/ N3 dilute ternary solutions of "2" and "3," and the carbon saturation parameter sc(3) (In f c/ N3) N c/N Fe for N3 - 0, are critically examined and correlated. It has been found that the interaction parameters and the atomic numbers of alloying elements follow regular periodic putterns. PHYSICO-chemical behavior of alloying elements in molten iron have become the subject of numerous investigations during the past 25 years. Consequently, the mutual effects of elements in the iron-rich solutions Fe-C-X, Fe-N-X, Fe-H-X, Fe-O-X, and Fe-S-X where X represents an alloying element, have gradually become better understood. These effects for a given temperature and pressure may be expressed by the interaction parameter of Wagner1, 2 derived briefly in the following manner. The complete differential of the Gibbs free-energy equation at constant temperature and pressure is dF = Fl dn, + F2 dn, + F3 dn3+ . . . [ 1] where F is the free energy; F 1, the partial molar free energy of "I"; and n,, the number of moles of "i." Cross-differentiation of this expression* *Cross-differentials are obtained as follows: Since the order of differentiation of F with n2 and n3 is immaterial, the left sides of the second differentials are equal, hence the derivation of Eq. [2] is obtained. For a dilute solution of components 2 and 3 in solvent 1, with the substitution of RT In f i = Fi xs for Fi where fi is the activity coefficient, and Fixs is the excess partial molar free energy, Eq. [2] becomes O) [3] where N2 and N, are the mole fractions. The interaction parameters are defined by

Jan 1, 1961

By Charles R. Simcoe

The stress-strain curves in the microyield region for various Fe-C solid solutions shown by Davies and Ku are typical examples of parabolic curves defined by the expression a = kEn 111 These data, when replotted on log-log coordinates, as shown in Fig. 9, exhibit three essentially parallel straight lines. It is apparent that carbon increases the flow stresses, but does not affect the exponent n. In other words, the only factor in Eq. [1] affected by in in carbon content is the constant k. As Eq. [1] is written k is the stress at a strain of 1.0. This is unsatisfactory for examining data in the microyield region. Therefore, the equation can be altered to the form: to permit the use of the authors&apos; microyield stress at a strain of 10-6 as k. Extrapolating the curves in Fig. 9 to a strain of 10-6 gives stress values of 2000, 3200, and 5400 psi for 0.008, 0.014, and 0.02 pct C, respectively. These values do not agree exactly with the authors&apos; measured values, but this will not affect the following discussion. The effect of carbon content on the slopes of the stress-strain curves shown in Fig. 2 of the paper by Davies and Ku can be analyzed by differentiating Eq. [2] with respect to strain. Thus: where n is always less than 1.0. Since n is essen- tially constant as a function of carbon content for the data under discussion, the slopes of the stress-strain curves depend only on k and E. If the slopes are examined at various selected Plastic strains. i.e., 10-6, 10-5, and so forth, it follows from Eq. [3] that the dif-ferent slopes for the different carbon contents depend only on the different values of ke=10-6. Thus, the larger ke=10-6, the steeper the linear stress-strain curve will rise with increasing plastic strain. This

Jan 1, 1969

By Sir John Cadnan

The production from the Maidan-i-Naftun area for the year ending March, 1928, was 5,340,000 tons (40,210,200 bbl.), an increase of nearly 13 per cent. over the production for the year ending in March, 1927. The production by years since the opening of the field in 1912 is given in the following table: [1 ton = 7.53 bbl.] Year Ended MaRch Tons Year Ended March Tons 1912 (7 months)............. 43,084 1920....................... 1,354,631 1913........................ 80,800 1921....................... 1,767,070 1914........................ 273,635 1922....................... 2,310,098 1915........................ 375,977 1923....................... 2,913,908 1916........................ 449,394 1924....................... 3,583,000 1917........................ 644,074 1925....................... 4,221,000 1918........................ 897,402 1926....................... 4,470,000 1919....................... 1,081,919 1927....................... 4,735,000 1928....................... 5,340,000 The actual production represents only a small proportion of the potential production. The Masjid-i-Suleiman Field The present producing unit, the Masjid-I-Suleiman, is an anticline some 20 miles in length by 4 miles in width, including three domes as so far proved. The producing horizon is a very open, dolomitic limestone, which, while showing much variation in texture and porosity, is so connected that the lowering of pressure in one section of the field quickly affects the whole area. The topography of the field is broken, with differences of well elevations of as much as 1100 ft. The depths to the limestone vary from about 800 to about 5000 ft. The closed-in pressure of the oil wells varies from zero to 50 lb. per sq. in. and that of the gas wells is about 450 Ib. Although the static oil level may be several hundred feet below ground level, in oil wells of high elevation, all the wells flow continuously or intermittently after they are once started—the majority continuously. The gas is very high in hydrogen sulfide in gas-oil wells of low pressure.

Jan 1, 1929

By S. Jana, C. M. Wayman

The reverse transformation of bcc martensite to the fcc phase was studied in an Fe-33.95 wl pct Ni alloy by nzeans oj dilatometry, melallography, and electron microscopy. Upon "slozc" heating (-1°C per min) length cJmnge us temperature plots showed u gradual contracLion over the temperature range 200" to 280"C ,followed by a more abrupt contraction beginning a1 -280°C. Howet,ev, zchen the heating rate was increased -4°C per tnin, no gradual contraction was observed and only the abrupt contraction starting at -2BO"C was found. Thus on slower heating- the AS "temperature" for the subject alloy, unlike the MS temperature, is better defined as a range of temperatures. Both optical and transmissiorl electron microscope observations showed that some of the martensite plates exizibited a partial loss of transformation twins during reversal. The midvib region of the martensite plates disappeaved relatively early duirng the reversal. Metallographic observations slowed that the earliest detectable stage of the rezlerse tvansforrvration begins (axd Moues inulardly) at The Martensens i te - parent interface. At higher temperatirres, the. formation of martensitically reversed jcc plates within the bcc martensite plales was observed. It is concluded that the reverse transformation consists of a diffusion less process (martensitic); but this is ps-obably aided by a prior or simultaneous dijjusiorz-comltvolled process, at leasl in the case of slower heat-ing&apos; experiments. ALTHOUGH numerous investigations have dealt with the parent-to-martensite ("forward") transformation (fcc — bcc) in Fe-Ni alloys, comparatively little is reported on the ("reverse7&apos;) martensite-to-parent transformation.&apos;-4 Even though such reverse transformations have been studied in detail in some nonferrous systems, one of the difficulties of studying the reverse transformation in most ferrous mar-tensites is that the martensite decomposes by tempering during heating. However, carbonless Fe-Ni alloys do not exhibit this difficulty since the transformation in these alloys is completely reversible. The present investigation represents an attempt to shed more light on the nature and mechanism of the martensite-to-parent transformation. 1) EXPERIMENTAL PROCEDURE 1.1) Alloy Prepatation. Fe-Ni alloys of compositions near 34 wt pct Ni were prepared from zone-refined iron (99.994 wt pct Fe) and high-purity nickel (99.999 wt pct Ni) by induction melting in recrystallized alumina crucibles in an argon atmosphere, with prior vacuum evacuation to 10"3 mm Hg. The alloys were homogenized by induction stirring in the molten state for 5 min. After solidification, the alloys were further homogenized in evacuated quartz capsules for 96 hr at 1230°C. 1.2) Dilatometry. Slices of the ingot were hot-forged (750°C in air) into approximate rod form and these specimens were then hot-swaged (750°C in air) into long cylindrical rods 0.55 mm diam. From the rods, specimens about 1 in. long were cut. These were then vacuum-annealed for 24 hr at 1200°C, cooled to room temperature, and subsequently transformed to martensite in liquid nitrogen (whereby about 40 pct transformation was obtained). Dilatation measurements were made by observing length changes in a vacuum dilatometer with an externally mounted LVDT sensing element. 1. 3) Preparation of Electron Microscope Specimens. Slices of the ingots were cold-rolled (with intermediate vacuum anneals) to -0.020 in. Out of these rolled sheets, specimens (about 1 by 1 in.) were cut. These were then vacuum-annealed, transformed to martensite by cooling in liquid nitrogen, and subsequently heated from room temperature to various temperatures to effect either partial or complete reverse transformation. These specimens were then chemically polished to 0.002 in. in l:l HsOz (30 pct) and &PO4 (85 pct) solution, and thinned to electron transparency in an electrolyte consisting of 150 g CraOs, 750 ml glacial acetic acid, and 30 ml ~~0.~ Observations were made with a 100-kv Hitachi HU-11 electron microscope equipped with an HK-2A tilting device. 1.4) Optical Microscopy. Metallographic observations were made with a Leitz MM5 metallograph on the same 0.020-in. sheet specimens as were used for electron microscopy and on bulk specimens which were 0.2 in. or more on a side. The chemical thinning solution when cooled below 20°C also served as an etchant for this alloy. Observations of surface relief were made with a Zeiss interference microscope employing a Thallium light source of wavelength 0.54 p. Specimens for interference studies were prepared by two-stage polishing on Buehler vibromet polishers using 0.3 and 0.05 p alumina abrasives. 2) EXPERIMENTAL RESULTS 2.1) Comparison of the MS,AS, and Af Tempera-tures wTth Previous Re sults. The AS aLd Af tempera -tures of several Fe-Ni alloys were determined dila-tometrically. The MS temperatures of the same alloys were determined by continuously lowering the temperature using a mixture of isopentane and liquid nitrogen and observing the highest temperature at which a prepolished specimen showed surface upheavals. For the present the As temperature is defined as the temperature at which an abrupt decrease in length occurs in the dilatation plot. The Ms,As7 and A determinations in the present investigation and those of Kaufman

Jan 1, 1968

By Robert A. Haney, Stephen J. Gigliotti, James L. Banfield

A series of investigations were made by the Mine Safety and Health Administration to evaluate the performance of various face ventilation systems as part of a program to reduce frictional ignitions of methane and to develop face ventilation systems that could be used with the line brattice more than 10 feet from the face. Tests were conducted in a full-scale laboratory model of a face area. Systems tested included unassisted blowing and exhaust line brattice, diffuser fan and spray fan systems. Systems were evaluated at air quantities ranging from 1.4 to 7.0 m3/s (3,000 to 15,000 cfm), and brattice-to-face distances from 1.5 to 9 meters (5 to 30 feet.). Tests were designed so that systems could be evaluated for the location of the high-point methane concentration in the face area, methane dilution capacity, and face ventilation index. The methane dilution capacity is the total amount of methane a system can dilute to 1.0 volume-percent. The face ventilation index is the efficiency at which the available face air volume is being used.

Jan 1, 1982

The Institute maintains a dual relationship with students: (1) an individual relationship with a Student Associate; and (2) a relationship with local organizations of students, known as Affiliated Student Societies or Student Chapters. 1. The conditions of Student Associateship are set forth in Section 8, .Article 1 of the By-laws of the Institute (see p. 45 and following pages) During 1934, sundry amendments were made for the purpose of improving the student relationship. Post-graduate students are now eligible; and the associateship can be maintained, with the payment of the regular dues of $2 per gear, for 18 months following graduation in June. A Student Associate is given a subscription to MINING A ND METALLURGY: he is accorded the privilege of getting special publications such as "The Porphyry Coppers" and "Ore Deposits of the Western States" at the reduced prices applicable to Members; he has the privileges of the Engineering Societies Employment Service and the Engineering Societies Library; and he is not only invited but urged to attend all meetings of the Institute, its Divisions and its Local Sections. The Institute wants to extend the hand of professional fellowship to students following mineral industries curricula.

Jan 1, 1936

By P. Chiotti, E. R. Stevens

The electromotive force between pure magnesium and Mg-Zn alloys in a fused KC1-LiCl-MgC12 cell was measured over the temperature range 360° to 730°C and for alloy compositions of 0.052 to 0.635 atom fraction magnesium. The calculated activity coefficients of magnesium in the liquid alloys may he represented by the relation These data and the phase diagram were employed in calculating the standard free energy of formation for the compounds MgZn, MgZn2, and MgZn2, In the temperature range from 25° to 590°C the relation ZINC-rich magnesium alloys have been shown to be very effective in reducing various solute chlorides or oxides from fused salts such as KC1-LiC1 eutectic. Such reactions are of interest in the developinent of pyrometallurgical methods for reprocessing nuclear reactor fuels.&apos; As the conceniration of the magnesium is increased beyond 5 to 10 wt pct the extent to which solutes, such as yttrium, lanthanum, cerium, and other rare earths, can be reduced or removed from the salt decreases. This effect is due to the resulting change in the activity of the solutes in the Zn-Mg alloy as well as the change in the activity of both the zinc and mag- nesium. The purpose of the present investigation was to determine the thermodynamic properties of the Zn-Mg system which, in addition to yielding information on the alloying behavior of these two elements, would permit a more quantitative understanding of the above reactions. Since this investigation was initiated several publications have appeared in the literature giving results on the thermodynamic properties for the liquid alloys of this system. 2-4 Kozuka, Moriyama, and Kushima3 measured the vapor pressure of zinc over four different alloy compositions by a carrier-gas technique. Eremenko and Tukashenko2 and Terpilowski4 measured the electromotive force between pure magnesium and various alloys in a fused salt cell. Earlier work has been summarized by Hultgren, Orr, Anderson, and Kelley.5 In the present investigation electromotive-force measurements were made on a cell of the type The temperature range covered for the lower-melting alloys was roughly 375° to 730°C. These data were employed in calculating the thermodynamic properties for the liquid alloys and in conjunction with the phase diagram,&apos; reproduced in Fig. 1, were used in calculating the standard free energy of formation of the compounds MgZn, MgZn2, and Mg2 Zn11. The results obtained are compared with available data from the literature. MATERIALS AND EXPERIMENTAL PROCEDURES Materials employed were: Bunker Hill slab zinc, 99.99 pct pure; Ames Laboratory magnesium containing 13 ppm N, 195 ppm C, and trace amounts of calcium, copper, nickel, and silicon; reagent grade KC1, LiC1; and high-purity MgC12 obtained from Dow Chemical Co. The electrolyte consisting of KC1-LiCl eutectic (44.4 wt pct LiC1) to which was added 15 wt pct MgCl2, was dried in a quartz tube by heating to 340° C under vacuum for a period of 4 to 5 hr, and then passing HC1 through the salt as the temperature was slowly raised to above the melting point of the salt. After about 3 hr the HC1 was shut off and the system flushed with argon and then vacuum applied for 1 hr. The salt was finally siphoned through a sintered glass filter and cast into a Pyrex container which was sealed and

Jan 1, 1965

By R. W. Olson, A. L. Benham

Viscous fingering was studied as it occurred in an open Hele-Shaw model (1 ft x 4 ft x 1/16 in.); it was also studied in the same model packed with 80-mesh glass beads during miscible displacements under unfavorable viscosity ratio conditions. It was determined that the lengths of 20 elements of the front were distributed normally around the average position of the combined elements under all conditions. Represented by the normal distribution, the length of the viscous fingers grew linearly with the distance traveled from the point of finger formation, increased with displacement velocity, and increased with increasing mobility ratio. Results obtained during the first few inches of displacement were of little or no use in predicting finger growth and/or finger length throughout the 4-ft model since the point of finger initiation cannot be predicted and would often occur several inches from the point of injection with either positive or apparent negative coordinates. The fingering occurring during a miscible slug displacement was much greater than would be predicted based upon the actual mobility ratios between in-place fluid and slug and between slug and following fluid, using the results described above for miscible displacement in the absence of a slug. Many of the experiments in the packed model showed that the rate of growth of the viscous fingers was diminishing toward the end of the displacement in the 4-ft long model, indicating that microscopic mixing, such as diffusion or dispersion, was decreasing the viscous fingering effect. INTRODUCTION Viscous fingering is a manifestation of a finger-shaped interface between displaced and displacing fluids occurring during typical miscible displacement projects for oil recovery. Its cause may be traced to the instability of a viscous fluid being displaced by a more mobile fluid. Viscous fingering takes on important significance in the miscible slug process 1.2 where it may be a dominant factor in determining minimum slug size. Experimental1-3 and theoretical4-7 studies of viscous fingering have been made by other investi- gators. However, an exhaustive study of the variables affecting viscous fingering had not been made. The present study was undertaken in an effort to determine the effects of some of the more obvious variables—such as mobility ratio, displacement velocity, distance displaced, and packing—upon viscous finger length and growth in a small laboratory model. It does not necessarily follow that conclusions reached by studying the results of this model study may be applied to the field. Future studies would have to evaluate the effect of model size on extension of these results. EQUIPMENT AND EXPERIMENTAL PROCEDURES A flow diagram for the equipment used in this study is shown in Fig. 1. Basically, it consisted of (1) a constant-rate pump for the injection of displacing fluid into (2) a model made up of two flat transparent plates spaced a small distance apart and (3) provisions for the production of fluid into a calibrated graduate. The displacing fluid contained a dye which allowed visual observation of finger spacing and length. The pump performed at rates from 2.5 cc/hr to 480 cc/hr, while pumping a light mineral oil into a bladder in a closed glass container holding the displacing fluid. The model was made up of two plates of 1-in. Plexiglass with dimensions 1-ft wide by 4-ft long. These were spaced 1/16 in. apart so that the internal model dimensions were 1-ft wide x 4-ft long x 1/16

In a letter to Prof. L. P. Breckenridge, chairman, urging the continua-tion of the Fuel Conservation Committee of the Engineering Council, Edwin Ludlow calls attention to the millions of tons of culm in the an-thracite region that can be utilized in properly equipped plants and the electricity generated transmitted to. New York, Philadelphia, and other nearby cities. He says: "Experiments have shown the economic value of No. 4 Buckwheat, which passes through a 1/16-in. mesh and over a 1/32-in. mesh. Culm passing through a 1/32-in- mesh is pulverized until it passes through a 300 mesh and is then burned under boilers. Two plants of this kind are now in successful operation in the anthracite region. Another rather interesting experiment was using 30 per cent. of this pulverized coal with 70 per cent. of oil in the generation of steam in the place of pure oil. This utilization of the fine anthracite, which has always been a waste product and thrown away, is not only fuel conservation in its truest sense but in the case of a bituminous strike, when no strike is contemplated in the anthracite field, will furnish fuel to manufacturing plants that otherwise would be obliged to shut down."

Jan 12, 1919

By G. R. St. Pierre, A. Ghosh

In the Si-C-0 system at temperatures of interest in process metallurgy there are four stable condensed phases—silicon, carbon, silica, and silicon carbide (Sic). Silicon melts at 1683oK1 and shows negligible solubility for carbon and oxygen at 1700°K. However, silicon dissolves approximately 1.5 at. pct C at 2500oK.2 Carbon in the form of graphite remains pure and dissolves negligible amount of silicon.&apos; Silica (crysto-balite) melts at 2001°K&apos; and is essentially a stoichio-metric compound. Silicon carbide is a solid and shows negligible deviation from stoichiometry up to approximately 2800oK.2 Besides the condensed phases there is a gas phase

Jan 1, 1970