Search Documents

By Hollis L. Caswell

The present status of integrated circuits utilizing. superconductive switching. elements is reviewed with special attention given to fabrication techniques, methods for interconnecting completed circuits, and refrigeration requirements. Cryoelectronics has been largely an "inte- grated-circuit" technology since its conception because the switching speed of superconductive devices is attractive only when these devices are fabricated with thin-film techniques. It is true that cryotron circuits can be constructed from wires of appropriate materials (as indeed was done by Dudley Buck 1 in his early investigations) but these circuits will switch in times characteristic of milliseconds whereas similar circuits fabricated by thin-film methods have potential switching times of nanoseconds. Furthermore, cryo-electronic devices such as the cryotron lend themselves readily to fabrication by thin-film techniques since these components may be made from polycrys-talline thin films and are relatively insensitive to the presence of impurities (as measured by semiconductor standards). Therefore, during the past decade considerable effort has been devoted to developing techniques for batch fabricating circuit arrays containing superconductive switching elements. Technology had developed to the point several years ago that fabrication of cryoelectronic arrays containing up to one hundred devices was rather straightforward. However, larger arrays containing between lo4 and 106 components which are required for commercial development of cryoelectronics still pose very severe yield problems. Thus in a sense cryoelectronics found itself in 1962 at the point semiconductor technology finds itself today; namely, individual devices and small groups of integrated devices could be fabricated with acceptable yield and the outlook for building larger integrated-circuit arrays was bright. Unfortunately, problems associated largely with yield have made fabrication of these larger arrays difficult. Unlike semiconductor technology, cryoelectronics had to solve the problems of large-scale integration before it could become economically attractive. This has proven to be a sizable burden to bear. Since several reviews exist on superconductivity,2 superconductive devices,3 and cryoelectronic technology, no attempt will be made in this paper to summarize these areas. Instead a few specific topics will be dealt with in more detail. First, a brief description is given of selected superconducting switching and storage devices with special attention to several metallurgical techniques which improve the performance of these devices. Second, techniques used to fabricate cryoelectronic devices are described with emphasis on problems affecting yield. Third, techniques for interconnecting a number of cryoelectronic planes are described. And last, refrigeration of cryoelectronic components is discussed briefly since the low operating temperature of superconductive devices is an important consideration in this technology. SUPERCONDUCTING STORAGE AND SWITCHING DEVICES The basic superconductive switching device is the thin-film cryotron. The geometry of this device is attractively simple, since it involves only the intersection of two lines that are electrically insulated from each other. The switching element (gate) and control element (control) of a crossed-film cryotron are arranged as illustrated in Fig. 1. The material for the gate is selected to permit the gate to be switched from the superconducting to the normal (resistive) state by the application of a control current. Tin, which has a critical temperature (T,) of 3.7°K, is commonly used for the gate and the cryotron is operated at a temperature just below T, (for example, 3.5°K). The control material (normally lead, with T, = 7.2°K) is chosen so that the control is never driven normal during circuit operation. To improve cryotron operation, a ground plane, also of lead, is placed under all of the circuitry to act as a diamagnetic shield and improve the current-density uniformity across the width of various thin-film elements. Normally, line widths vary from 0.005 to ^ 0.020 in. and film thicknesses from 300 to 10,000A, although new fabrication techniques make narrower lines feasible. In fabricating cryotrons it is important that the edges of the gate elements be geometrically sharp to avoid undesirable switching characteristics associated with a thinner edge region, Fig. 2. One technique which has been used extensively to form patterns consists of placing a physical mask containing the film pattern between the evaporation source and the substrate and depositing through the mask. Film strips formed in this manner possess a penumbra at the film edges due to shadowing of the evapor-ant under the mask. Several techniques have been proposed for minimizing effects due to this penumbra. One of the more promising metallurgical techniques

Jan 1, 1967

By K. S. Venkataraman

The physical properties of clay-water systems depend on the complicated system of forces between the clay particles themselves, and between the clay particles and the ions in the liquid phase. The kind and distribution of ions in, on, and between the clay particles and the size and the shape of the particles are the basic factors determining the macroscopic behavior of clay-water systems. Understanding the system requires a knowledge of the nature of the clay particles, their size, structure, composition, and surface properties, and of the manner in which they interact with ions [and molecules] in the surrounding liquid [or other medium]. The validity of Professor Brindley's words (Brindley, 1958), written three decades ago in the context of making pottery, whitewares, and electrical porcelains, transcends time, and the basic message is perhaps all the more important in the considerably expanded use of ceramics for structural, thermal, tribological, electronic, and other applications. Silicon carbide, silicon nitride, and sialons have been studied in the last two decades for high- temperature structural and tribological applications, particularly for using in internal combustion engines. Titanates, zirconates and niobates of barium, strontium and lead, have high dielectric constants, and are extensively used in the formulations for making capacitors. Hexagonal ferrites (molecular formula MO.6Fe2O3) are in use for making permanent magnets for fabricating miniature motors, and for assembling loud speakers, particle accelerators etc. Cubic ferrites such as magnesium-zinc ferrite and nickel-zinc ferrite are used as transformer cores, and for other high-frequency applications. In this context, Richerson's recent book (Richerson, 1984) on the general scope of traditional and technical ceramics is a good starting point for an overview of contemporary ceramics technology. Glasses are a whole class of amorphous materials used widely as sintering aids, and for making glass-bonded ceramics and glass-ceramic composites. Composites are yet another burgeoning field where two or more particulate components are used for improving the performance of ceramics. For all these applications, the inorganic starting materials are almost always submicron and near-micron powders. Understanding the powders' physicochemical properties, and their surface chemical interactions with the surrounding liquid/gaseous medium is-necessary for making reliable ceramic parts at competitive prices. Even though ceramics science and engineering has attained its separate identity in universities and the industry, ceramists themselves would concede that ceramics science is a cross-disciplinary field, having incorporated and assimilated within itself many principles from several apparently disjointed disciplines. Principles of material science, graduate-level physics and chemistry, polymer science, surface and colloid chemistry, transport phenomena, particle technology, unit operations commonly used in chemical engineering and mineral processing, and statistics and applied mathematics are integral part of any ceramics curriculum in universities. Added to this is the fact that all bench-scale successes in making ceramic parts are to be scaled-up for larger throughput operations. Understanding and applying process engineering principles of comminution, classification, drying, calcination, etc. then becomes essential. CERAMIC FORMING: Despite the diversity of the materials and processes, conceptually, the steps involved in making ceramic parts have remained the same over several decades: The different components for making the pan (usually one or more powders plus other forming and sintering additives) are proportioned and mixed thoroughly, and the well-mixed formulations are consolidated into desirable shapes known as "green bodies." Usually binders such as wax, clay, organic polymers and surfactants, whether dispersed or dissolved in a suitable liquid are used during mixing the batch for giving strength for the green bodies. In the dried green state, the inorganic powders typically occupy only 55 to 60% of the bulk volume of the body, depending on the particle size distributions of the powders and the forming history, with mostly inter- particle voids accounting for the rest of the void volume. SINTERING: The formed bodies are then fired in high- temperatures kilns/furnaces during which the parts are exposed to a predetermined temperature profile, and "soaked" for a certain duration at the final high temperatures, typically between 1200 K and 1900 K, and then cooled to room temperature. The gaseous atmosphere in the furnace is controlled (oxidizing, reducing, or inert) when necessary. During the initial stages of firing, volatile liquids evaporate, and during the intermediate temperatures between 400 and 600 K, the the organic polymeric additives pyrolize and oxidize into water vapor, CO, C02, and other gases. At still high temperature, the glasses, when present, soften, and simultaneously, the ceramic particles rearrange into a network of grains with definite grain boundaries so as to reduce the total interfacial free

Jan 1, 1990

By D. Turnbull, J. H. Hollomon, J. C. Fisher

Application of the concepts of nu-cleation and growth to the analysis of experimental transformation data has led to valuable descriptions of phase transformations, an outstanding example being the transformation austenite —* pearlite which has been examined with particular care by Mehl and co-workers.&apos;-5 In addition to the pearlite transformation, the proeutectoid fer-rite and proeutectoid carbide transformations are known to proceed by nucleation and growth. Martensite, on the contrary, until recently was thought to form by a mechanism involving neither nucleation nor growth; however, extension of standard nucleation theory6 suggests that martensite, bain-ite, and the other products of austenite decomposition all grow from nuclei in the parent phase. The theory that martensite forms by nucleation and growth is strongly supported by recent experimental work of Kurdjumov and Maksimova.7 The concepts of nucleatioli and growth have been fruitful also in providing a sound basis for quantitative theoretical treatments of the kinetics of phase transformations. For example, Volmer and Weber8 and Becker and Döring9 developed the theory of nucleation from fundamental considerations to a point where excellent agreement was obtained with the results of experiments on the condensation of supercooled vapors. As a result of their analysis, the kinetics of vapor-liquid transformations now can be predicted. It seems probable that application of the theories of nucleation and growth to a quantitative study of austenite decomposition similarly will clarify the nature of the individual transfor: mations involved, and will enable the calculation of austenite transformation kinetics. In the present paper, the theories of nucleation and growth are applied to the austenite ? martensite transformation in steels. The analysis begins with a discussion of nucleation in single component systems. Martensite appears to be coherent with the parent austenite, hence the nucleation theory is modified to include the effects of elastic distortion. Nucleation in the two component iron-carbon system then is discussed, for most steels are primarily alloys of these two elements. Finally, M. temperatures and martensite transformation curves are calculated for each of several alloy steels of varying carbon and chromium content, and are compared with those determined experimentally by Lyman and Troiano10 and Harris and Cohen.11 Nucleation Theory NUCLEATION IN SINGLE COMPONENT SYSTEMS6,12-14 The work required for reversible formation of a region of phase within the parent a phase is expressed conveniently as the sum of two terms: W1 = Aa, the product of the area of the interface and the interfacial free energy, and W2 = VAf, the product of the volume of the region and the free energy increase per unit volume associated with the transformation. The total work is therefore W = Aa + VAf. When a is more stable than ß, Af is positive and W increases without limit as the volume increases. The transformation a ?ß does not occur. It is nevertheless true that small regions of phase ß enjoy temporary existence here and there in the a. The equilibrium number of ß regions of given size is proportional to exp(— W/kT) per unit volume of a, assuring that larger (ß regions occur with diminishing probability. When a is less stable than ß, Af is negative and W passes through a maximum as V increases. Assuming for simplicity that regions of ß are spherical, as is true when the interfacial tension is isotropic and there are no elastic strains, W = 4r2a + (4/3)*r3Af The maximum value of W is W* = 16iro3/3Af2 [1] for regions with radius r* = -2o/Af. [2] For single component condensed systems it has been shown14 that the steady rate of nucleation of 0 per unit volume of untransformed a is nearly proportional to exp[- (W* + Q)/kT] where Q is the activation energy for the unit processes of adding or removing one atom from an embryo or nucleus. If To is the temperature at which a and ß are in equilibrium, the rate of nucleation is a maximum at a temperature 0 < T < To where (W* + Q)/kT is a minimum. P regions smaller than critical size are called embryos; they tend to grow smaller and disappear, only exceptionally growing larger. Regions equal to or larger than critical size are called nuclei. A critical size nucleus may grow indefinitely large or may shrink back to a, either process decreasing the free energy of the region.

Jan 1, 1950

By F. B. Samani, B. Stabel

The 1,000 MW Hydro Power Station Masjed-e-Soleiman (formerly called Godar-e-Landar) in Iran is under construction since 1992. The rock engineering aspects of the major underground structure, i.e. the powerhouse cavern shall be reported on in detail. The geotechnical investigations are described and results given. The results of several geotechnical analyses are presented. The designed and executed rock support is given. A description of the monitoring systems and typical measurement results obtained during and after excavation are presented. The lessons learnt during construction of the Stage-I powerhouse cavern were applied on the extension of the powerhouse cavern, which is to house an additional 1000 MW. Details regarding the unexpected behaviour of the Mudstones are given. Die 1000 MW Wasserkraftanlage Masjed-e-Soleiman (vormals Godar-e-Landar genannt) befindet sich seit 1992 in Bau. Dieser Artikel berichtet im Detail über die felsbaulichen Aspekte der Untertagebauwerke, insb. der Maschinenkaverne. Die geotechnischen Untersuchungen werden beschrieben und deren Ergebnisse wie die Ergebnisse verschiedener Berechnungen werden präsentiert. Die geplante und die ausgeführte Felssicherung wird angegeben. Die eingebauten Überwachungseinrichtungen werden beschrieben und typische Ergebnisse während des Aushubs und danach werden dargestellt. Die Erfahrungen beim Aushub der Kaverne der Stufe I wurden beim Entwurf der Kaverne der Erweiterungsstufe II, die weitere 1000 MW beherbergen wird, berücksichtigt. Details zum unerwarteten Verhalten des Schluff-/Tonsteins werden angegeben. La centrale hydroélectrique de Masjed-e-Soleiman (dénommée anciennement Godar-e-Landar), d’une puissance de 1.000 MW, est en construction depuis 1992. Un rapport détaillé sera présenté sur les aspects relatifs à la construction en enrochements de l’aménagement souterrain principal, à savoir la caverne abritant la salle des machines. Une description des investigations géotechniques réalisées y est fournie ainsi que les résultats correspondants. En outre sont présentés les résultats de plusieurs analyses géotechniques. L’ancrage dans la roche tel que projeté et réalisé est présenté. Une description des systèmes de contrôle ainsi que les résultats de mesures typiques obtenus au cours des travaux d’excavation sont donnés. Les leçons tirées lors de la construction de la Phase 1 de la caverne de la salle des machines furent appliquées à l’extension de la caverne de la salle des machines, qui doit abriter une unité supplémentaire d’une puissance de 1.000 MW. Par ailleurs, des détails sont donnés sur le comportement inattendu des argilites.

Jan 1, 2003

By Y. Nakada, U. F. Kocks, B. Chalrners

THE orientation dependence of work hardening has previously been studied over the entire range, i.e., including special orientations of high symmetry, in aluminum1-3 and silver.* The differences between various orientations are substantial, and the trend is the same in all fcc crystals. However, there are quantitative differences in behavior between aluminum and silver at room temperature, particularly in the (100) orientation. While many experiments on gold have been reported,5&apos;9 none included the special orientations. We therefore undertook tension tests on gold crystals of the axial orientations (100),(110), (Ill), (211), and, as a representative of single slip, one whose Schmid factor was 0.5 (hereafter referred to as m = 0.5). Single crystals of dimensions 1/4 by .1/4 by 6 in. were grown from the melt1&apos; at a rate of 4 in. per hr, using gold of 99.99 pct purity obtained from Handy and Harman. A growth rate of 1/8 in. per hr, or a purity of 99.999 pct,ll produced no difference in results. The crystals were annealed at 1000°C in air for 24 hr and furnace-cooled down to room temperature, after which they were electro-polished in a solution of potassium cyanide (40 g), potassium ferrocyanide (10 g), soda (20 g), and enough distilled water to make 1 liter of solution, at a current density of 0.02 amp per sq mm. After 2 or 3 hr, a very smooth surface was obtained by this method. Nine m = 0.5, two (loo), one (110), three (Ill), and one (211; crystals were tested at room temperature in a floor-model Instron machine at a tensile strain rate of 0.5 pct per min. The accuracy of the stress measurement was k10 g per sq mm up to 500 g per sq mm, k2 pct for higher stresses. The strain measurement was accurate to t2 pct. The scatter of stress at a given strain among the crystals of the same orientation was small, *5 pct being the largest. The representative stress-strain curves for various orientations are shown in Fig. 1. Table I summarizes the work-hardening parameters as used by seeger.12 Results of other investigators are also included in this table for comparison. There are no previous data for the corner orientations. Values for m = 0.5 crystals agree fairly well with those of Berner. Tm is defined as the stress at which the stress-strain curve begins to deviate from linearity of Stage 11. However, in practice this is a very difficult value to estimate because each investigator has a different idea of linearity. Therefore, the comparison with the values of other investigators may not be valid. In the present experiment, (100) crystals had the highest 111, followed by (111) crystals. The work-hardening rate in Stage I1 was highest for the (111) crystal followed by the (100) crystals. Our value for 0x1 of m = 0.5 orientation agrees very well with those of other investigators. 1) Single-Slip orientation (m = 0.5). These crystals were oriented so that the primary-slip vector was contained in one side face. The dimension perpendicular to this side should then not change if single slip indeed takes place. Within the accuracy of measurement, this dimension did not change during the deformation. Since the accuracy is k0.2 pct, the amount of secondary slip is less than 0.7 pct of the slip on the primary-slip system at 30 pct tensile strain. This is in conformity with the results obtained by Kocks" for aluminum crystals. The tensile axis moved toward (211) during the deformation. Slip bands, Fig. 2(a), were very fine and closely spaced. Some deformation bands were observed. There were no clear-cut cross-slip traces such as the ones observed on aluminum m = 0.5 crystals. 2) (111) Crystals. The orientation of the tensile axis was stable during the deformation. From this observation, one can deduce that at least three slip systems must have operated, and probably all six because the remaining three all have cross-slip relation to one of the first three.&apos; It was very difficult to observe the slip markings. Consequently, we could not confirm by this method that six systems were operative during the deformation. At high strains (above 50 pct shear strain), this orientation had the highest stress-strain curve. At 80

Jan 1, 1964

By O. D. Sherby, J. E. Dorn

SEVERAL years ago Zener and Hollomon1 suggested that the flow stress of metals might be related to the temperature and strain rate in accord with the functional equation: s=s(eeh/rt) [1] at the same state. The Zener-Hollomon relation also contains the significant tacit implication that the energy for activation, AH, is substantially independent of the state of the material. The utility of this method for correlating creep data with tensile data was illustrated in a preliminary reportL on the effect of alloying additions on the secondary creep rates of binary a solid solutions in aluminum as shown for Al-Mg alloys in Fig. 1. Not only do the secondary creep and ultimate tensile properties for each alloy correlate well on this plot but in addition the activation energy, AH = 17,900 R cal per mol. is identical for the various compositions. Similar types of curves correlating the secondary creep rates at 422°K (300°F) with ultimate tensile data were also obtained for a series of dilute a solid solutions of copper, germanium, zinc, and silver in aluminum. In all cases the activation energy for creep, AH, was found to be equal to about 17,900 R cal per mol independent of the type of alloying element or its concentration. The coincidence of the activation energies for these alloys is probably due to the fact that the activation energies for creep are rather insensitive to small composition changes. Alloying additions, as shown in Fig. 1, however, increased the stress necessary to obtain equivalent values of ee?H/RT. Thus the stress level in curves of the type represented by Fig. 1 gives the relative creep strengths of the various alloys. Inasmuch as these correlations between creep and tensile data were obtained for creep tests at 422°K, it appeared advisable to ascertain the range of secondary creep rates and temperatures over which correlations between creep and tensile data could be made on the basis of the Zener-Hollomon relationship. If, for example, the activation energy changes with different ranges of creep temperatures, the utility of the proposed analysis would be severely weakened. But if AH is constant not only for all dilute alloys, but also over wide ranges of temperature and secondary creep rates, confidence will be developed not only in the broad utility of the Zener- Table I. Chemical Analysis&apos;:&apos; and Grain Size of Alloys Mean Grain Residual Impurities. Wt Pct Diam- Alloying Atomic-eter, Element Pct Si Fe Cu Mg Mn mm Aluminum 99.987 0.003 0.003 0.006 0.001 0.25 Magnesium 1.617 0.003 0.004 0.006 0.26 Copper 0.101 0.003 0.003 0.0006 0.001 0.29 Zinc 1.616 0.003 0.005 0.007 0.001 &apos;0.26 * The authors express their appreciation to the Aluminum Company of America for the preparation and chemical analyses of these alloys. Hollomon relationship, but also in its theoretical justification. The following investigation was instituted in order to ascertain the range of validity of the Zener-Hollomon relationship when it is applied to creep and tension data. Materials, Equipment, Technique In view of rather extensive correlatable data now available on the plastic properties of a series of binary a solid solutions of magnesium, copper, germanium, zinc, and silver in aluminum, these alloys were again selected for the present investigation. Previous reports have already covered the tensile properties of these alloys at subatmospheric temperatures," and at elevated temperature," as well as their fatigue properties at atmospheric temperatures, nd their creep properties at 422°K.&apos; Resistivity measurementsa as well as precision lattice constant determinations? evealed that these alloys are a solid solutions. After homogenization. 0.100 in. thick sheets were rolled to 0.070 in. in thickness and recrystallized to about the same grain size. Since the details of these treatments were reported previously," they will not be repeated here. In order to appropriately reduce the scope of creep tests in this investigation only the typical alloys shown in Table I were investigated. All creep specimens were machined such that their tensile axes were in the rolling direction of the 0.070 in. sheet stock. The gage section was 2 in. long and 0.500 in. wide with a reduced section of 3.50 in. Creep strains were measured by means of rack and pinion type extensometers with a sensitivity of 0.005 in. per division. Readings were estimated to 1/10 of

Jan 1, 1953

By Bobby Dupree

I remember a big problem with a seismograph in the winter two years ago. In response to a citizen’s complaint I placed a transducer near the corner of a two-story home. It was a pretty nice day for the winter months, the people were pleasant, and I had no problems digging a hole to place the transducer.

Jan 1, 2004

By J. P. Morris

PREVIOUS investigations1,2 have shown that alloying elements in liquid iron influence the thermodynamic activity of sulphur and thereby affect the partition of sulphur between metal and slag in the desulphurization process. For example, the greater efficiency of desulphurization in the blast furnace as compared to the open hearth can be attributed in part to a higher level of sulphur activity in blast-furnace metal due to the higher concentration of carbon and silicon. In the present investigation, a short study was made of the influence of manganese on the activity of sulphur in liquid iron and iron-carbon alloys. In contrast to carbon and silicon, manganese was found to decrease the activity coefficient of sulphur; and in iron-carbon alloys it counteracts to some extent the influence of carbon. However, at manganese concentrations normally present in the blast furnace or open hearth, the effect of manganese is small. Since manganese sulphide has a limited solubility in iron, manganese can act, under certain conditions as a desulphurizing agent. Considerable data on the manganese-sulphur product in carbon-saturated melts were obtained in the investigation and have been included in this report. The experimental procedure was the same as that used in the earlier investigations on the effect of silicon&apos; and carbon&apos; on sulphur activity. Briefly, the method was as follows: The molten alloy, contained in a graphite or sintered alumina crucible, was brought to equilibrium at a constant temperature with a mixture of hydrogen and hydrogen sulphide of constant composition by bubbling the gas through the metal. Samples of&apos; the melt were taken for analysis at regular intervals by suction through a 2 to 3 mm bore silica tube dipped into the metal. The experiments were run in a graphite spiral resistance furnace with melts weighing 50 to 60 g. The gas bubbling tubes were made of sintered alumina and were 5/16 in. OD, 1/16 in. ID, and 24 in. long. Equilibrium was assumed to have been attained when the sulphur content of the liquid metal reached a constant value. During an experiment there was a rapid loss of manganese from the melt by volatilization. To offset this loss, small additions of manganese were made periodically. The rate of manganese addition needed to maintain a constant manganese concentration was determined in preliminary tests. In all of the experiments, deposits of manganese sulphide formed above the melts in a cooler region of the furnace. Apparently, these deposits resulted from a reaction between manganese vapor and hydrogen sulphide in the gas. To prove that manganese sulphide did not volatilize from the melts to a measurable extent, an experiment was run in which helium was bubbled through liquid iron containing both manganese and sulphur. Although manganese volatilized rapidly in this test, there was no appreciable loss of sulphur. Volatilization of manganese sulphide from a melt would have led to an apparent equilibrium condition in which the sulphur content of the metal was lower than the true equilibrium value. The experimental results are shown in the first seven columns of Table I. The data in the last two columns were obtained from the previous work on the effect of carbon&apos; and show what the results would have been in the absence of manganese but with temperature, gas composition, and carbon content of the metal remaining the same. Comparison of the last four columns show that, in the presence of manganese, the sulphur content of the metal increased at equilibrium and the activity coefficient of sulphur decreased. However, the results show that, for manganese concentrations below 3 pct, the effect of manganese is small. The values for activity coefficient of sulphur given in Table I were calculated from the following relations: S (in liquid metal) + H2 (gas) = H2S (gas) [l] K ph2s/?s X %S X phg = 0.00251 [2] where K is the equilibrium constant for the reaction, PH2S and ph2 are the partial pressures of hydrogen sulphide and hydrogen, respectively, and ?s is the activity coefficient of sulphur. The standard state for sulphur was taken to be a 1 pct solution of sulphur in pure iron. The numerical value for K at 1600°C was determined in the earlier work. For the purpose of showing graphically the results of the tests run at 1600°C, the activity coefficients of sulphur were recalculated so as to correspond to a manganese concentration in the metal of 2 pct in each case. In the calculation it was assumed that the increase in sulphur content of the metal at equilibrium caused by the presence of manganese

Jan 1, 1953

By E. L. Garton

[Analyses of may crude oils produced in Louisiana are included in reports that t have boon published by the Bureau of Mines. The first report, giving, analyse of 6 Louisiana crude oils, was 3 published in 1921 and this was followed a year later by Report of Investigations 2416,4/ giving 7 additional analyses. The eleven most important of these analyses were incorporated in Bulletin 291.5/ issued in 1928 In 1934 analyses of 26 crude oils produced in southern Louisiana were published.6/ The percent report presents analyses of 72 additional samples of crude oil from 45 fields in 23 parishes In Louisiana.]

Jan 1, 1939

By M. G. Benz

The superconducting performmce of diffusion-processed Nb3Sn is influenced by its micro structure. High isotropic transverse current density may be achieved in this material by a process which forms a precipitate of ZrO, within the Nb3Sn. FOR an ideal type-I1 superconductor, little or no transport current can be carried in the mixed state; i.e., little or no transport current can be carried above the lower critical field H,,, where the field penetrates abruptly in the form of current vortices or fluxoids, even though full transition to the normal state does not occur until the upper critical field H,,.&apos; Fortunately, nonideal type-I1 superconductors can be readily obtained and these carry large transport currents up to the upper critical field H. Both theoretical and experimental investigations have attributed this current-carrying capability for nonideal type-I1 superconductors to pinning of the fluxoid lattice by heterogeneities in the microstructure of the superconducting material. These heterogeneities may take the form of dislocations or dislocation clusters,2"5 grain boundaries: structural imperfections introduced by phase transformations; radiation damage,8"10 or precipitates.11"15 Nb3Sn formed by diffusion processing is a type-I1 superconductor. Heterogeneities are needed for high superconducting critical currents above H,,. This paper will cover: a) what the microstructure of diffusion-processed NbSn looks like; b) what changes in the microstructure take place when the system is doped with precipitates, and c) how these changes in microstructure influence the superconducting critical currents. EXPERIMENTAL Preparation of Samples. Diffusion processing was used to form the Nb3Sn. The procedure used was as follows: a) coat the surface of a niobium tape with tin; b) heat-treat this tape at a temperature above 930°C to form a layer of Nb3Sn at the Sn-Nb interface. Such a layer of NbsSn is shown in Fig. 1 The thickness of the NbsSn layer formed was controlled by the time and temperature of the heat treatment. The same general procedure was used for preparation of both undoped samples and samples doped with a precipitate. An additional step was included in the preparation of the doped samples which consisted of internal oxidation of zirconium to form ZrOn. The details of the doping process will be reported in a later paper. Sample Testing. The Nb3Sn tape samples were soldered to a copper or brass shunt. Current and voltage leads were then attached to the sample in the usual four-probe resistance measurement configuration. The sample was cooled to 42°K. In some cases it was cooled in the presence of a high magnetic field and in other cases with the field turned off. The results were the same for both cases. The samples were oriented in a configuration with field transverse to current but could be rotated such that the angle between the field vector and the wide side of the tape sample could be changed. Measurements up to 100 kG were done in a superconducting solenoid and measurements above 100 kG in a water-cooled copper magnet at the MIT National Magnet Laboratory. Once the test field was reached, the current in the sample was increased until voltage was detected across the sample. The critical current was taken as the current at which voltage was first detected in excess of background noise. In most cases this was 1 to 2 x 10~6 v for a— in.-wide sample carrying several hundred amperes with a in. separation between voltage leads and with a 10 "-ohm shunt resistance. RESULTS AND DISCUSSION Microstructure. Examination of the microstructure of the undoped Nb3Sn shows rather large-diameter (1 to 2 columnar grains growing outward from the niobium surface toward the tin surface. As the layer is made thicker by longer diffusion times, these grains grow longer. Few new grains are started. Transmission electron microscopy shows little or no second-phase material within the bulk of the Nb3Sn layer. The microstructure of a diffusion-processed NbsSn layer changes quite drastically when the system is doped so as to form a precipitate within the NbsSn layer. Instead of large-diameter columnar grains of NbaSn forming, smaller-diameter (0.5 to 1 ) equiaxed grains of Nb3Sn decorated with the precipitate form. Fig. 2 shows a transmission electron micrograph of a Nb3Sn layer doped with zirconium oxide. This layer has been etched so that one may look between the grains

Jan 1, 1969

By J. A. Murray

Maintaining satisfactory air quality in electrowinning tankhouses is problematic and costly, particularly as plant operating current densities have increased. Conventional approaches have not proved completely effective. These include the use of beads, hollow spheres, surfactants and coalescer devices. They require powerful ventilation systems to be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses.

Jan 1, 1996

By W. R. K. Wu

This bulletin traces the development of high-pressure, coal and tar hydrogenation technology, based on an intensive review of the pertinent literature. The bulletin was written as a part of the Bureau of Mines research program on synthetic liquid fuels. It covers the history and economics of the process; the chemical aspect of hydrogenation of coal, tar, and middle oil; the engineering aspect of converting coal and tar to liquid fuels, principally gasoline; and the equipment for the process. The literature covered includes documents of the United States and British Governments, journals, and other publications. Bureau results in the hydrogenation field are also incorporated.

Jan 1, 1968

By Howard Roscoe

Linking Ashford International Station to the new Channel Tunnel Rail Link required over 5000 rotary bored and CFA (continuous flight auger) piles to form tunnel walls and viaduct foundations and to support overbridges and trackside barriers.. Much of the work was carried out close to the existing railway infrastructure. Plunged columns were used to maintain traffic flows over the tunnel site during construction. The results of an extensive programme of vertical and lateral load tests on bored and CFA piles in heavily overconsolidated Weald Clay are compared to illustrate the relative importance of stress relief and of prolonged exposure to bentonite. The completion on schedule of this major piling and ground engineering contract (value £30 million) demonstrates that collaborative working in partnership produced cost effective solutions to a series of challenging technical and logistical problems.

Jan 1, 2002

By Ray. K. Filip

The concept of installing a steel sheet pile retaining wall into the ground by "pressing" has resulted in the development of various equipment solutions over the last thirty years e.g. Taylor Woodrow ?Pile Master&apos;, Giken &apos;Silent Piler" & Tosa &apos;Still Worker?. Dawson Construction Plant Ltd (DCP), have recently advanced the pile pressing concept with the introduction of their &apos;Push-Pull&apos; system. This advancement offers significant improvements in the quality of installation compared with traditional pressing solutions but also greater versatility, higher productivity and, most importantly, generates new opportunities through a wider range of applications for "silent piling&apos;. This paper will focus primarily on the use of the Push-Pull concept in the construction of a unique "integral" bridge in Milton Keynes, England. Finally, the paper touches on the development of quiet, vibration-less pile extraction equipment, which allows steel to be considered the foundation material of choice for truly sustainable construction. It is no longer acceptable to leave unwanted piles in the ground.

Jan 1, 2006

By Alessandro Bertero, Dylan Pearson, Wesley Schmutzler, Matteo Bertoni

"The SR 83/US 331 highway is located in the Florida panhandle, where it connects the Walton County beaches to the I-10 corridor. The roadway is of vital importance to the economy of the area as well as its safety since it represents the primary hurricane evacuation route from southern Walton County. The Florida Department of Transportation (FDOT) decided to increase the number of traffic lanes from two to four and improve the geotechnical properties of the moderately deep, very loose foundation soils, that had affected the highway rideability for years. The soil mixing was selected as the method to meet the unique deep ground improvement challenges of the project. The design required that Shallow Mixing Method (SMM) be used to build a 10-foot thick platform that transferred axial load to the bottom soil layers through a series of Deep Mixing Method (DMM) columns. Upon completion over 8,300 SMM columns and 1,500 DMM columns had been installed, with no remedial work required. Also, only 1% of the almost 1,500 specimens tested did not meet the specification requirements. This paper will describe the challenges encountered and provide valuable information that may be useful for other future projects, including details not previously published.INTRODUCTIONThe counties of Walton and Okaloosa have been a very popular vacation destination for many ears. The 50-mile long coastline boasts beautiful, sugar-white beaches and waters the color of emeralds. The popularity of the area has been growing even further, over the last few years. A consequence of this phenomenon is a fast-paced increase of the traffic flow on the SR83/US331 highway, especially at the bridge that connects the Walton County beaches across Choctawhatchee Bay (Fig. 1) to the heavily traveled I-10 corridor. The highway plays a very important role for the area also as a commercial link and as the primary hurricane evacuation route from southern Walton County. The increase in traffic has produced higher travel time, when not a complete traffic paralysis, and exacerbated the issue of ground settlement where accelerated wearing of road foundation occurred due to the presence of very loose, moderately deep, soils, that had afflicted the highway for several years. The Florida Department of Transportation (FDOT) decided to put an end to these issues by increasing the number of traffic lanes from two to four and improving the geotechnical properties of the foundation soils. The Design-Build Maximum Price Request for Proposal (RFP) issued for the expansion of the Choctawhatchee Bay Bridge saw the participation of numerous D/B teams which produced various technical solutions. Among them, the FDOT selected the Skanska/Parsons Brinckerhoff (General Contractor) proposal which provided for the use of soil mixing as the ground improvement technology. The design/build team assigned Foundation & Geotechnical Engineering (Designer of Record) the ground improvement design which Treviicos South (Specialty Contractor) would execute."

Jan 1, 2017

By Aram Grigoryan

This paper addresses historical aspects and construction sequencing of the subway complex under Columbus Circle in Manhattan; the structural elements of the rehabilitation and new construction; and the challenges associated with design and construction. PB is providing engineering services to New York City Transit (NYCT) for the rehabilitation of the 59th Street/Columbus Circle Station Complex that services over 150,000 customers daily. The project involves structural repairs, modifications and new construction requiring underpinning and temporary supports, custom framing details, and construction staging procedures to meet stringent limitations within the operating transit station and around the Columbus Circle street intersections.

Jan 1, 2008

By K. A. Slagle

Hydraulic analysis of the wellbore has become increasingly inzportant for designing cementing operations and selecting equipment, materials and techniques to complenzent modern well-c-ompletion practices. Non-Newtonian fluid technology has advanced beyond the point where former empirical methods of analysis adequately define the hydraulic system and fluid properties. In view of these factors, this paper describes a series of rheological calculations which have been found practical, through field usage, for assistance in selecting a cementing program. A relatively simple laboratory method using standard viscometric equipment is suggested for determination of the rheological properties of slurries, and clrrta are presented on some of the more common cementitrg conzposition.A. A criterion for divergence from laminar-flow characteristics has been proposed. Usefulness of the calculations is indicated by examples of cementing operations where they have been used. INTRODUCTION With the changing aspects of well-completion practices during the past few years, it has been increasingly important to have a relatively simple method of analyzing the flow conditions existing in the well during cementing operations. This is particularly true in view of the improved economics toward which most of the changes have been directed. Rheological characteristics of slurries used for cementing should be a major consideration in the trend toward smaller casing sizes, either single or multiple strings. Receiving increased attention is the practice advocated in 1948 by Howard and Clark&apos; of attaining turbulent flow with the fluids circulated during a primary cementing operation. While there may still be a difference of opinion concerning this technique, most available information indicates that superior primary-cementing results are generally obtained when high displacement rates are employed. Fluid properties of the slurry to be used must be available, as well as calculation methods, to determine what flow rates should be attained and the probable consequences in terms of frictional pressure and horsepower utilization. It would certainly be inappropriate to attempt high displacement velocities if sufficient pressure might be developed to create lost circulation. Since cementing slurries are non-Newtonian fluids, it is not possible to define their rheological or fluid properties by the single factor of viscosity and then make calculations for the quantities just described. Because the shear stress-shear rate ratio is not constant: it becomes necessary to establish at least two parameters for adequate fluid-flow calculations. It is not the purpose of this paper to delve into the mathematical development of non-Newtonian technology, nor to discuss the arbitrary classification system under which a single fluid may resemble two or three different classes depending upon experimental conditions. Rather, the intention is to present a useful series of calculations based on a concept applicable to both Newtonian fluids and to the preponderance of non-Newtonian fluids encountered in the oil-producing industry. Development of this approach was begun some 32 years ago,&apos; and has most recently been brought to fruition by Metzner and his co-workers at the U. of Deleware. Some non-Newtonian fluids encountered in the petroleum industry, other than cementing slurries, have also had the benefit of this method of analysis."&apos; The two parameters required to define the fluid are usually denoted by the symbols n&apos; and K&apos; and, for the purposes of this discussion, are called "flow behavior index" and "consistency index", respectively. These two slurry properties permit calculation of the Reynolds&apos; number and the "critical" velocity, or the velocity at which departure from laminar flow begins. EXPERIMENTAL DETERMINATIONS The two principal instruments used for rheological studies are the pipeline (capillary-tube) viscometer and the rotational viscometer. When conveniently possible, a capillary-tube viscometer (where the pressure drop and flow rate of the material can be measured) is the better method for rigorous determination of the flow behavior index and consistency index for non-Newtonian fluids. With pressure-drop data at various flow rates, it is then possible to prepare a logarithmic plot of shear rate as the abscissa-shear stress as the ordinate. For fluids which do not exhibit time-dependency, these data will usually produce a straight line. The flow behavior index n&apos; represents the slope of this line, while the consistency index K&apos; becomes the intercept of this line at unity shear rate in accordance with the mathematical derivations associated with this concept of rheology. Due to the difficulties anticipated in maintaining a uniform, pumpable cement slurry for the time interval required to obtain measurements from the pipe viscometer, the n&apos; and K&apos; data reported herein were obtained using a direct-indicating rotational viscometer (Fig. 2). The

By L. Forsbacka, L. Holappa

Viscosities of quasi-ternary CaO-SiO2-CrOxmelts in contact with metallic chromium were measured by the rotating cylinder method up to 1750ºC. Twelve slag compositions were selected in the composition range 20–55 wt% SiO2, 10–45 wt% CaO and 10–60 wt% CrOx. Estimation of the amounts of CrO and Cr2O3was made by regression analysis based on the earlier data. Professor Iida’s (Osaka University) viscosity model was applied and model parameters (0CrO,CrOand Cr2O3) were evaluated. The Iida model gave good consistency with the measured viscosity values.

Jan 1, 2004

By David Jurich, Joseph N. McDivitt

INTRODUCTION South Coast Water District (SCWD) operates the Beach Interceptor Sewer Tunnel(BIST) in South Laguna, Orange County, California between Monarch Beach and Aliso Beach (Figure 1). The 10,200-foot long BIST houses a 24-inch gravity Techite sewer pipeline critical to the SCWD Sanitary Sewer Collection System. The original tunnel and sewer pipeline were constructed in 1954 and the sewer line was replaced in 1974.Periodic inspections by sewer pipeline maintenance crews documented deterioration of specific intervals of the tunnel. Rotting timber supports and rock falls in the tunnel as a result of the deterioration were endangering the sewer pipeline and a 731-foot section of tunnel located at Thousand Steps Beach was determined to be in immediate need of repairs. SCWD and consultants Hatch Mott MacDonald (HMM) and Tetra Tec prepared a Work Plan for emergency tunnel stabilization and pipe protection measures that was implemented in January 2007. Normal access to the beach and the section of tunnel requiring repairs was limited to public stairs referred to as Thousand Steps and, therefore, all materials and equipment needed for the work were transported to the beach by ocean-going landing craft. Additionally, the emergency repairs had to be completed without taking the pipeline out of service. Numerous environmental, logistical and operational requirements had to be overcome to complete the challenging emergency repairs. GEOLOGICAL SETTING The Laguna Beach area is located in the Peninsular Ranges of Southern California. The project area is located on the southwest flank of Niguel Hill along marine wave-cut cliffs and slopes. The tunnel was excavated in the San Onofre Formation, a marine deposit, characterized by abrupt lateral and vertical changes in lithologies that vary from boulder to cobble and gravel size breccias to medium coarse sandstones with gravel, sandy claystone and siltstone. The interval of the tunnel that required repairs is located within the San Onofre breccia, a moderately-to-well cemented, poorly bedded to massive unit with angular to subangular boulder and cobble sized clasts of schist. The sandy silt matrix of the breccia is composed of quartz, feldspar and schist grains (Figure 2). GENERAL TUNNEL DESCRIPTION The approximately 6-feet high by 6-feet wide 10,200-foot-long BIST was hand mined in 1954 at the base of the coastal cliffs. Primary access is through twenty-one access adits from public and private beaches. The tunnel is located in an easement that extends beneath private property with residential structures situated 50 to 80 feet above and horizontally in close proximity to the tunnel alignment. Most of the tunnel is horse-shoe shaped and unsupported, but approximately 3,000 feet is supported by timber

Jan 1, 2007

By Han Xuanjiang

Through whole analysis of static testing piles information of a teaching building, this paper put for ward that when the ratioes of unload rebound amount to residual deformation and to total settlement reach the maximum, the testing load is selected as allowable capacity of single pile by camparing with the settlement in the practical engineering, it is proved that this method fits to practice, for other several projects, its also available. Therefore non-destructive testing pile method was improved, so all the tested piles can be reused as engineering piles.

Jan 1, 1991