Search Documents

By L. C. Brown, S. K. Behera

The diffusion rate in Ag-Sb couples is sensitive to con~pressive load with the width of Ag3Sb, the only phase present in the diffusion zone, increasing with stress up to 800 psi and remaining constant above this. Kirkendall marker experiments show silver to diffuse much faster than antimony in Ag3Sb and incipient porosity may therefore develop at the Ag/Ag3Sb interfnce restricting the transfer of atoms from the silver into the diflusion zone. Application of compressive stress reduces the tendency for porosity to develop and so increases the growth rate. In a recent paper Brown et al.1 observed a significant increase in the thickness of Cu2Te in Cu-Te diffusion couples on application of a compressive stress as low as 20 psi. Similar stress effects have also been observed in the Fe-A1,2 Al-u,3 arid cu-sb4,5 systems. It has been suggested that the increase in growth rates of intermetallic phases in these systems is due to a decrease in the amount of Kirkendall porosity with applied stress. In the present paper, results are presented of the effect of compressive stress on diffusion in Ag-Sb, together with a detailed examination of the Kirkendall effect. The Ag-Sb phase diagram6 shows that antimony has a moderate degree of solid solubility in silver, 5.7 at. pct at 350°C, but that there is essentially no solubility of silver in antimony. There are two intermediate phases— (hcp7) from 8.8 to 15.7 at. pct Sb and Ag3Sb (orthorhombic8) from 21.8 to 25.9 at. pct Sb. EXPERIMENTAL Diffusion couples were prepared from fine silver of 99.95 pct purity and from antimony of 99.7 pct purity. Both the silver and antimony were produced in the form of discs 1/2 in. in diam by approximately $ in. thick, with surfaces ground flat to 3/0 emery paper. Diffusion anneals were carried out in the apparatus previously described.1 A compressive load was applied to the diffusion couple through a lever arm system, with a reproducibility estimated to be ±10 psi. All runs were carried out in a protective hydrogen atmosphere. Following the diffusion anneal specimens were sectioned and polished and the width of the diffusion zone was measured metallographically. Composition profiles were measured using an electrostatically focused electron probe with a spot size of 10 , counting on Sb L radiation. Corrections for matrix absorptiori and fluorescent enhancement9 were not required. S. K. BEHERA, formerly Graducate Student, Department of Metallurgy, University of British Columbia, is now Postdoctoral Fellow, Whiteshell Nuclear Laboratories, Atomic Energy of Canada Ltd., Pinawa, Manitoba. L. C. BROWN, Junior Member AIME, is Associate Professor, Department of Metallurgy, University of British Columbia, Vancouver, B.C., Canada. Manuscript submitted June 14, 1968. IMD RESULTS Fig. 1 shows an electron probe traverse of a typical diffusion zone. In all couples examined only one intermediate phase was observed and the composition of this phase, 23 wt pct Sb, was in good agreement with the composition of Ag3Sb, 23 to 28 wt pct Sb. The presence of this phase was confirmed by X-ray diffraction of filings taken from the diffusion zone. The probe traverses showed no detectable solid solubility in either the silver or the antimony although the phase diagram indicates that some antimony, up to 6.5 wt pct pct Sb, should be in solid solution in the silver. However the width of this portion of the diffusion zone would be expected to be very small in view of the low diffusion coefficient in the silver, 4 x 10-l6 sq cm per sec at 350°C, 10 compared with that in the Ag,Sb, estimated as 3 x 10-8 sq cm per sec in the present work, and this region would therefore not be expected to be seen in the probe traverse. Application of stress resulted in a significant increase in the width of the diffusion zone, Fig. 2. At 350°C, the thickness of Ag3Sb increased from 250 at 0 psi to 400 p at the limiting stress of 800 psi, indicating an apparent 150 pct increase in the diffusion coefficient. Similar behavior was also observed at 400°C, indicating that the stress effect is not characteristic of just one temperature. The growth of Ag3Sb at 350°C and at various stresses is shown in Fig. 3. In every case the growth rate was parabolic indicating diffusion control. The kinetic curves all passed through the origin showing that delayed nucleation of Ag3Sb was not responsible for the stress effect and that it was a real growth effect. A series of tests were carried out in which diffusion was allowed to take place at a lower stress following an initial high stress diffusion anneal. Speci-

Jan 1, 1969

By T. M. Williams, P. M. Green

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The sediment geochemistry of streams draining Southern Uplands and Lake District turbidites was compared with lithogeochemical data for the source greywackes, using stratigraphically defined catchments. Several systematic trends in element abundance variation between source and stream sediment can probably be applied more widely to interpretation of drainage geochemistry. Pb and Zr increase markedly from source rock to sediment, by adsorption on clay and zircon grain concentration. Variation of feldspar-related elements Rb, Sr, K and Ba appears to be controlled by source grain size and compositional maturity. Ni shows surprisingly little change and Fe and Co are only slightly raised. Cr is particularly useful, with variations superimposed in anomalously high regional levels. Abrupt changes in Cr distribution in stream sediment coincide with stratigraphical boundaries, allowing drainage data to be used as a surrogate for whole-rock values

Jun 19, 1905

By E. G. King

As low-temperature heat-capacity and entropy data were available for only one sesquisulfide (cerium sesquisulfide), it appeared desirable to augment the information for this class of compounds by measuring the sulfides of antimony and indium. In addition a pressing need existed for data on indium sulfide to supplement vaporization studies in progress in the Department of Mineral Technology, University of California. This Bureau of Mines paper reports low-temperature heat-capacity measurements and entropy evaluations at 298.15° R. of antimony sesquisulfide of stoiehiometric composition (Sb2S3) and of indium sesquisulfide which was somewhat deficient in sulfur (In2S2.93). The data for the latter substance were adjusted to correspond to the stoichiome tric composition (In2S3 ) . Indium sesquisulfide has a lower entropy at 298.15' K, than either antimony sesquisulfide or cerium sesquisulfide, in line with the higher atomic density of the indium compound.

Jan 1, 1962

By J. E. Murphy

The u.s. Bureau of Mines investigated electrode designs for electrowinning lead metal from a LiCl-KCl-PbCI2 electrolyte at 4500 C. The major objective of this investigation was to decrease the energy requirement for lead electrowinning. Electrolysis was performed in a bench-scale cell using several graphite electrode assemblies. Such parameters as electrode spacing, current density, and chlorine gas removal from the anode were investigated in the bench-scale tests. An optimum electrode assembly, termed the sawtooth design, was scaled up and operated at 3,000 and 4,000 A. The sawtooth electrodes operating at 3,000 A produced lead for 0.66 kW·h/kg. The electrodes were constructed by cutting large triangular grooves in the electrode surfaces. The electrodes were placed together such that the triangular peaks of one electrode projected into the triangular valleys of the other electrode. Chlorine did not build up on the anode with the sawtooth electrodes.

Jan 1, 1991

By Y. M. Chen, H. L. Zhang, W. U. Bing, C. Q. Zhou

Multiphase flow in the widely used Vanyukov furnace was numerically studied. An unsteady three-dimensional and three-phase flow model was firstly built using the computational fluid dynamics (CFD) software ANSYS FLUENT®, and then solved with the volume of fluid (VOF) and k - ??model. The results showed that the proposed model could be used to predict the multiphase movement, the slag/air fluctuation, the vortex formation, and effects of structural and operational parameters. By fast Fourier transform (FFT), the dominant frequency of density with time signal was calculated as 0.29 Hz. The analysis of different injection flow rates of enriched air indicated that this variable has a major effect on the mean slag velocity. The peak mean velocity increased from 2.17 to 4.99 m/s while the flow rate of enriched air varied from 70 to 160 m/s. The proposed model provides a method to optimize the furnace structure and operating conditions for the best furnace performance and lowest energy consumption.

Jan 1, 2015

[nder ' 1Oclific?atic>n 1 l', of Cant r Ict No. S012?U7 , the T1. S. l urc ,:i.11 of Miries ontracted tivit.l '1 -l:eudurn? Barry t1rirl ,~:>:'nci.11c:, for the 1>crfcocrnancu of a afet, Analynin Q::tc n Study to develop a plan for thc organiration nrld opera¬ion of a 'Lur('an ,`,afutj i ily ;i Cn11tur, r Before the con)y)lctic>n of the stucly, the Abiretu.l ustaldish d such a center, the WniL1, and Safety i?'\naly:-.in Cnmtor (l1S;'J:), under the dirucHan of fly, Assistant Director of JTc'"?ltl) 11111 .itut~ 1O1- 'l (.. -11: 'C'a) :_'-, ?'( )'t. 11. ~.C is 11 c' iC1cnlC:rtc:rr'd at the 1)crnv(jr Federal Center, 1)u:r',L C,r_i1f,U, rK.]

Jan 1, 1972

By O A. Cottrill, G A. Oldfield, S B. Nowell

Host-rock û wallrock major and trace element geochemistry associated with epithermal gold mineralisation in the Hauraki Goldfield of New Zealand is poorly documented, even though rock geochemistry is a recognised tool in exploration. Such responses assist in recognition of the regional scale imprint of fossil hydrothermal activity, and indicate targets for detailed evaluation within these alteration zones.   Recent investigation of gold deposits in the Waihi (Gladstone), Golden Cross (Empire), Thames (Waiotahi) and Coromandel (Tokatea) areas indicate enrichments of Au, As and Sb in the andesitic wallrocks hosting mineralisation. Of the other elements examined, Si, K and Rb are enriched, and Na, Ca, and Sr are depleted at all deposits. These trends are best developed in the vicinity of veining. In deposits with clay alteration dominating (Waiotahi and Tokatea) there is also depletion of Mg, Mn, Zn and Cu. Ba and Cr are variably enriched or depleted within different styles of alteration. Base-metal enrichment in the wallrocks is not a feature of Hauraki deposits.

Jan 1, 1990

By P. H. Derbyshire

The use of continuous flight auger piles has increased significantly in the U.K. to such an extent that it is now the most widely used method of constructing small diameter bored piles. This paper describes the improvements in equipment, techniques and particularly monitoring that have led to this growth. A review of the equipment in use describes how purpose built self erecting machines have been generally adopted. Improvements in ancilliary equipment are described. Concrete has almost completely replaced grout and techniques have been developed to extend the length of reinforcement that can be placed. Leading specialist contractors have developed instrumentation to monitor the construction of the pile (in terms of time, depth, torque, concrete pressure and flow) and keep a record for checking. A further significant development of this monitoring by means of sensors at various levels in the auger stem is described. The results obtained from this monitoring are reviewed and future developments discussed.

Jan 1, 1989

The MINER Act of 2006 mandated that all underground coal mines must install and maintain refuge chambers. Refuge chambers serve as a temporary shelter in case of emergency. Several factors affect the performance of a refuge chamber: heat production inside the chamber and introduction of CO when chamber doors are opened are two major factors. This study examines the CO purging process and to determine total air quantity and time necessary to lower the CO con-centration to safe levels for different inlet/outlet configurations using three-dimensional simulation technique. The study uses Reynolds Averaged Navier Stokes and continuity equations along with the spe-cies transport model assuming uniform air mixing. The heat transfer of any kind is neglected and the purging process is assumed to take place isothermally. The standard k-e model is utilized for simulating turbulence in the flow field. This research provides useful guidelines in developing an efficient strategy for purging refuge chamber. Keywords: Airlock chamber, Purging, Carbon monoxide, Turbulence

Feb 27, 2013

Mr D. Wilson was born in Vereeniging, where he also completed his schooling, matriculating from General Smuts High School in 1977. Mr K.A. van Gessel was born in 1937. His final studies were conducted at Delft University, where he graduated with an M.Sc. degree in mining engineering. Mr J.G. McCaUum was born in 1938 and matriculated at Jeppe Boys' High School, Johannesburg. Mr H. Scot RusseU started his mining career at Randfontein Estates Gold Mining Co. Witwatersrand, Limited, where he served as temporary Geological Assistant, Sampler, Surveyor, Shift Boss, and Mine Overseer. Mr A.M.P. Henderson was born in 1950, in Kiel, West Germany. Mr J.L. Nel matriculated in 1957. This was folowed by his atainment ofthe folowing degrees: B.Sc. (Chemistry, Physics) in 1961, B.Sc. Hons. (Metalurgy) in 1965, M.Sc. (Metalurgy) in 1967, and MDD (student of the year) in 1981

Jan 1, 1989

[A Editor's Note: Annual Reviews of various subjects and areas are found in February issues of Mining and Metallurgy and Mining Engineering. These Annual Reviews are not listed per se in the Index. Abating Stream Pollution in Anthracite Coal Fields. ME Mar 50 Abbadia San Salvatore mine, Italy. T178, 297 Abbott, C.E.: Limestone Mine in the Birmingham District. With Discussion. T129, 62 ABC Typifies Trend to Mechanized Mining and Coal Preparation. ME Dec 50 Abel, J.F.: Statistical Analysis of Tunnel Supporting Loads. T235, 288 Sulzbach, J. F., and Walker, D.K.: Ice Tunneling in Greenland. ME Jun 59 Aberfoyle tin mines, sphalerite, chalcopyrite, stannite, as intergrowths. T214, 1147 Abnormal Behavior of Some Ore Constituents and Their Effect on Blast Furnace Operation, The. T241, 1 Abrams, C.J.: Industry's Responsibility in Postwar Economy. M&M Mar 45 and Haley, D.F.: History of Crushing and Milling at Climax. M&M Jun 46]

Jan 1, 1972

By J. Oré

An alternative method for dewatering slurry (tailings) is the use of geocontainers (MacTubes). The practical application of this work was carried out in the concentrator plant of the Raura Mining Company, located in the occidental mountain between Huánuco and Lima in Peru?s central highland. For the development of the research, the MATLAB R2012a software MGeST (v. 1.0) was used (Slurry Geocontainer Maccaferri Treatment). MGeST is used for sizing MacTubes, which allows determination of the most important design parameters, such as height (H), filling residual pressure (P1O ), strength of geosynthetic (T), and dehydration height. Compared with GeoCoPS v. 3.0, there is a maximum difference of 3% between the results obtained. The tailing to be treated in the MacTube have a specific weight of 11.62 kN/m3. After several tests it was determined that a MacTube of an apparent opening size of 0.22 mm was required for this specific weight.

Aug 1, 2013

By T. Wang, R. G. Reddy

"A new eutectic of LiNO3-NaNO3-KNO3 ternary system was calculated by using thermodynamic modeling and the eutectic temperature was predicted to be 389.15K. The melting point was determined using Differential Scanning Calorimetry (DSC). On repeated measurements, it was found that the melting point of the eutectic composition showed excellent reproducibility with the predicted value. The heat capacity was also measured using DSC and the data as function of temperature were fit to polynomial functions. Subsequently, the thermodynamic properties such as enthalpy, entropy and Gibbs energies of this novel ternary eutectic salt mixture were deduced as function of temperature.IntroductionIn these days, the provision of the large amount of energy required in the peak period relies more and more on the parabolic trough solar power plant and it works by utilizing the thermal transfer fluid. Consequently, the development of inoovative thermal transfer fluid with higher energy storage density is paramount to lower the expense for generating energy [1-4]."

Jan 1, 2013

By Lassi Klemettinen

For better understanding and maximal value utilization of the WEEE smelting process, the behavior and distribution of different trace elements must be known. In this study, the behavior of nickel as a trace element was studied in an equilibrium system with metallic copper—spinel saturated iron silicate slag (with 3 wt-% K2O)—iron aluminous spinel—gas. The experiments were conducted in alumina crucibles at 1300 °C, in oxygen pressure range of 10−10–10−5 atm. A time series of 15–60 min experiments was also conducted for investigating the formation rate of the primary spinel phase in the system. The results show that the distribution coefficient of nickel between metallic copper and liquid slag changes from approximately 70 to 0.4 along the increasing oxygen pressure range. In addition, a significant part of the nickel deports into the spinel phase. The spinel formation was investigated based on composition analysis results and visual observations from SEM-images.

[A Aalseth, Earl P. (M 51) Geol, Amerada Petr. Corp., Box 1498, Billings, Mont. Abadie, Henry G. (M 43) Asst to Supvr of Oper, Long Beach Oil Dev. Co., 255 S. Santa Clara, Long Beach 7, Calif. Abbe, T. Waldo (A 56) Ass't Dist Oper Supt, Sun Oil Co., Beaumont, Tex. Abbott, J. L. (M 56) Partner, Pritchard & Abbott, 501, Century Bldg, Fort Worth, Tex. Abbott, Richard H. (J 51) Owner, Abbott & Howard, 422 W. Hermosa, San Antonio, Tex. Abbott, Seth J., Jr. (M 51) Tekoil Corp., .2;A6 Mercantile Nat'l. Bank. Dallas, Tex. Abbott,. William G. (M 50) Div Mgr, Rice Eng. & Op. Inc., Box 1142, Hobbs, N. M. Abderhalden, R. R. (J,59) Box 100, Carmi, Ill. Abel, Malcolm D., Gen Mgr, Bakke Oil Co., Midland, Tex. Abel, Raymond L. (M 28) Prof of Chem Engr, Univ. of Pittsburgh, Pittsburgh 13, Pa. Abel, Wayne K. (M 57) 1513 Patton Drive, Odessa, Tex.]

Jan 1, 1961

By M. L. Apel

A conceptual approach to the bioremediation of uranium mill tailings (UMT) is presented., This approach focuses on, biosorption to remediate the. effluent solution and bioleaching remediate the. solid fraction. Comparative biosorption studies were performed with synthetic single metal solutions using a commercially available biopolymer. The maximum rate of metal sorption by calcium alginate was found to be 5.43, 6,39, 6.48, and 9.74 mg dm-3 min-1 for U022*, Ba2+, Cd2+ and Zn2+, respectively. Activation energy (AEa) for barium uptake by calcium alginate beads was determined to be 11.5 kJ, indicating a diffusion controlled reaction mechanism. Thermodynamic values (AG+ AH+ and ASt) of the metal-alginate activated complex, as reported in the literature, were found to be in agreement with those calculated from this research. Results show that this biopolymer can be effectively applied in the removal of select metals prevalent in uranium mill tailing effluents and associated waste streams.

Jan 1, 1991

By Youn-Bae Kang

Evaporation mechanism of S from liquid Fe–C–S alloys at 1873 K was proposed by analyzing available experimental data. It has been known that increasing C content in liquid alloy increases activity coefficient of S ðfSÞ, and it could raise driving force for the evaporation reaction S = S(g). However, experimental data of the evaporation of S in the Fe–C–S alloys could not be accounted for only by considering the increases of fS. In the present study, formation of carbosulfides, CS(g) and CS2(g), was additionally taken into account in order to explain role of C for the accelerated S evaporation. Surface adsorption of S was also taken into account, which retards the evaporation rate of S. An evaporation model equation was formulated. It can be applied to calculate the evaporation rate of S over wider C content (from zero to its saturation to liquid alloy).

Aase, Glenn D., (J'40) Jr. Met.. American Smelt. k Refin. Co., Selby, Calif. Abadie, Henry G., (J'43) Petr. Engr., Avenal, Calif. Abbott, Clarence E., (M'04) Civil Engr., V.P.. Tennessee Coal, Iron & R.R. Co., 1542 Brown Marx Bldg., Birmingham, Ala. Abel, Raymond L., (M'28) Chem. Engr., C.O., Pitts¬burgh Chem. Warfare Procurement Dist., American Bank Bldg., Pittsburgh. Pa. Abel, Walter D.. (M'32) Min. Engr., Supvr. Engr., R.F.C.Lee Angeles, Calif. Abele, Louis T., (M'31) Route No. 1, Adameville, Tenn. Abell, Leo M., (M'31) Mill Supt. & Met., Emperor Gold Min. Co. Ltd., Vatukoula, Fiji Is. Abernathy, G. E., (M'38) Geol., Kansas State Geol. Survey, Pittsburg, Kans. Abernathy, Jack H,, (M'40) Asst. Cenl. Supt. of Prod., Sunray Oil Co., 11th Floor, Philtower Bldg.. Tulsa 3. Okla. Abernethy, D. Carl, (M'44) Min. Engr. Rm. 3217, N. Int. Bldg., Washington, D. C.

Jan 1, 1944

By R. D. Wilson

Ten to twelve million tons of dust is produced by cement kilns annu-ally in the United States, resulting in a serious waste disposal problem. The Bureau of Mines investigated two alkali volatilization methods for converting this dust into materials for making portland cement and a useful potassium product. Portland cement kiln dust was found to be composed of finely ground cement raw materials (CaC03 and 8i02) having a layer of alkali sulfate (K2S04 and Na2S04). In this form, it cannot be directly recycled to cement kilns because concrete is weakened by a reaction between the alkali and the aggregate. Portland cements with 28-day strengths above 5,000 psi were produced from low-alkali residues using sintering and melting methods. For nearly complete removal of alkalies, primarily potassium sulfate, from cement kiln dust, a temperature above 1,300° C and a reducing atmosphere were required.

Jan 1, 1986

Thermodynamics and kinetics? of the removal of Va elements (As,Sb,Bi) from copper were investigated 1n the fire relining by alkaline carbonate fluxes such as Li 2co3 , Na 2CO3 and K2CO3. The distribution coefficients of As, Sb and Bl between alkaline carbonate fluxes and mo) ten copper were ?obtained at 1200°C under the different oxygen potentials. As and Sb were easily removed from copper to fluxes as pentavalent oxide form. On the other hand, Bi was hardly removed except by a Ll2CO3 flux. The removal rates of Va elements from copper were also measured In the temperature range of 1150°C.- 1250°C. The removal rates of As and Sb were much higher than that of Bi. The removal rates of Va elements showed the same order of the distribution coefficients. The removal rate could be expressed by following equation. (1).

Jan 1, 1987