Search Documents

By R. J. Brison, O. F. Tangel

The development of a new method of mineral separation was sponsored by the International Salt Company, which requested Battelle Institute to investigate means for improving the quality and appearance of rock salt from the Company's Detroit mine. Although developed specifically for removing impurities from rock salt, the general method may be applicable to other separation problems. The principal impurities in rock salt from the Detroit mine are dolomite and anhydrite which represent 2 to 5 pct of the weight of the mined salt. In the size range from 1/4 to M in. (the range of primary interest in this project) the impurities are only partially liberated from the halite in normal production. Further size reduction to improve the liberation of impurities is not practicable in view of the market requirements for the coarse grades of rock salt. Laboratory separations in heavy liquids showed that, to improve the quality and appearance of the rock salt substantially, it would be necessary to remove not only free gangue particles but also a large proportion of the locked-in particles. Because rock salt is an inexpensive commodity, a low-cost process was required. Gravity methods were, of course, considered. The heavy-liquid separations indicated that a split at an effective specific gravity of 2.2 to 2.3 would be required. (The specific gravity of pure halite is 2.16.) Heavy-media separation was investigated but had the disadvantages that it was necessary both to operate with saturated brine and to dry the cleaned salt, and that the cleaned salt was darkened by the magnetite medium. Air tabling was tried but did not give the desired separation. It soon became apparent that established methods would not provide a satisfactory solution and work was undertaken on the development of a new process to solve the problem. PROCESS DEVELOPMENT Preliminary Experiments: At the start of the investigation, an analysis of the problem indicated that the diathermacy of rock salt—that is, its ability to transmit radiant heat—might form the basis for an efficient separation process. Under this theory, the impurities might be selectively heated by radiant heat. The particles could then be fed over a belt coated with a heat-sensitive substance so that the warm impure particles would adhere preferentially to the coating. After the initial experiments, made by heating the rock salt with an infrared lamp and separating the product on small sheets of resin-coated rubber, proved encouraging, a small continuous separation unit was set up. This comprised 1) a simple heating unit consisting of a vibrating feeder covered with aluminum foil and an infrared lamp mounted above the feeder and 2) a separation belt 6 in. wide and 36 in. long. A sketch of the device is shown in Fig. 1. Results with this apparatus confirmed the fact that a good separation was possible. It was apparent, however, that a considerable amount of experimental work would be needed to develop the scheme to a practical and economical process. The Process: Basically, the process consists of two main steps: 1) selective heating by radiation and 2) separation of the heated particles on a heat-sensitive surface. Because neither of these steps had previously been utilized commercially in mineral processing, it was necessary to do basic research on both aspects. Factors studied in the investigation included type of heat source, design of heating unit, design of separation belt, selection of heat-sensitive coating, removal of heated particles from the belt, contact between particles and coating, and maintenance of the heat-sensitive surface. Part of the experimental work was carried out on a small-scale unit consisting of the 36x6 in. belt and auxiliary apparatus, and part on a larger unit. For simplicity, discussion of work on both of these units is grouped together. SELECTIVE HEATING Radiant-Heat Source: The essential requirements for a radiant-heat source were 1) that the radiant heat be in a wave length range which is effectively absorbed by the impurities but not absorbed appreciably by the rock salt and 2) that it be dependable, practical, and economical. Selection of a heat source of suitable wave length range was one of the first considerations. It is well known that pure halite is highly transparent to radiant energy in wave lengths from 0.3 to 13 microns. However, the available data on infrared transmission by dolomite and anhydrite, particularly in the range below two microns, were not complete enough to serve as a reliable basis for selection of a heat source. Although it may have been possible to obtain sufficient data on infrared transmission and absorption to enable one to select the best heat source, a more direct procedure was used. This consisted simply of exposing the crude rock salt to each of several types of radiant-heat source on the small continuous separation device. The heat sources investigated, approximate source temperature used, and calculated wave length of maximum radiation are tabulated in Table I. Of the two types of tungsten-filament lamps investigated, both the short wave length photoflood lamps and the longer wave length infrared lamps were satisfactory from the standpoint of selectivity

Jan 1, 1961

By Damien Wagner

To reduce the emission of greenhouse gases by the steel industry, particularly for ironmaking, the production of DRI (Direct Reduced Iron) using hydrogen as the reducing gas instead of carbon monoxide is being considered. In this context, the reduction of pure hematite by hydrogen was studied at the laboratory scale, varying the experimental conditions and observing the rate and the course of the reaction. All the reduction experiments were performed in a thermobalance and supplementary characterization methods were used like scanning and transmission electron microscopy, X-ray diffraction, and Mössbauer spectrometry. The influence of rising temperature in the range 550-900°C is to accelerate the reaction; no slowing down was observed, contrary to some literature conclusions. A series of experiments consisted in interrupting the runs before complete conversion, thus enabling the characterization of partially reduced samples. Interpretation confirms the occurrence of three successive and rather separate reduction steps, through magnetite and wustite to iron, and illustrates a clear structural evolution of the samples. Finally, the influence of the sample type was revealed comparing a regular powder, a nanopowder and a sintered sample. The regular powder proved to be the most reactive despite its larger grain size, due to a more porous final structure.

Jan 1, 2006

By Quast K

A series of laboratory flotation tests were conducted to evaluate the effectiveness of various depressants as arsenic (and zinc) depressants in the lead cleaner stage of the NBHC mill at Broken Hill. The depressants used included potassium cyanide, ferrous sulphate, sodium hypochlorite, potassium ferricyanide and two Cyanamid commerical depressants, Aerodepressants 610 and 633. A standard roughing stage was completed before the addition of the reagents in the cleaning stage. All reagents tested produced significant arsenic depression, with the best results being obtained with the addition of potassium cyanide and sodium hypochlorite. Some of the depressants activated the zinc in the process of arsenic depression. The best result was obtained with the addition of 90 g/t potassium cyanide at a pH of 10 when arsenic recovery was only 1/4 that of the value obtained for the standard test.

Jan 1, 1991

By C. N. J. Wagner, E. N. Aqua

The bee alloys of the terminal solid solution of rhenium in niobium were investigated by X-ray diffraclion methods. The analysis of the broadening of the powder pattern peaks from the niobium-rich alloys, cold-worked by filing, showed evidence for faulting on (211) planes. The alloys with larger rhenium concentrations were brittle, and fractured when filed. The analysis of the shapes of the diffraction profiles from powders produced by hammering with steel plates) of these brittle alloys indicated that the broadening was due predominantly to platelets bounded by clibe planes. This result was consistent with the Laue patterns from single-cleazlage facets which showed evidence for clearage fracture on {100} planes. The influence of faulting on the mechanical properties of face-centered cubic (fcc) metals and alloys, i.e., how faulting affects the various dislocation configurations in fcc metals, is well-known.' The important question is whether or not faulting occurs in body-centered cubic (bcc) metals and alloys, and, furthermore, if faulting does occur, to what extent it affects the mechanical properties. Theoretical calculations indicate that the stacking-fault energy is rather high in most bcc metals.2 The results of sev-eral studies using transmission electron microscopy have indicated that faults are present in well-annealed and lightly deformed bcc metals and alloys, such as tungsten,3 vanadium,4 and Mo-Re alloys.5,6 These faults, as have been observed, may be stabilized by the presence of interstitial (C,N,O) atom segregation to the extended dislocations. In addition, there is considerable X-ray diffraction evidence for faulting in bee metals,7-8 using the same techniques that were successful for the study of faulting in fee metals and alloys.7 This X-ray diffraction method is currently the only technique applicable for the investigation of faulting in metals with high stacking fault energies, i.e., when severe amounts of deformation are required to produce sufficient amounts of faulting to be detectable by X-rays. The thinned films of heavily deformed metals will become opaque in the electron microscope due to the high dislocation densities present. In a previous investigation of faulting8 in bee metals of group Vb and VIb, the authors observed that niobium was ductile when filed at room temperature, and showed the highest density of faults on the (112) family of planes. A niobium-base alloy system was therefore chosen to study the effect of alloying on the occurrence of faults in a bcc alloy. There is a large range of terminal solid solubility of rhenium in the alloys of the bee refractory metals. All of the Group VIb-rhenium alloys, i.e., Cr-Re, Mo-Re, and W-Re, exhibit solid solution hardening without loss of ductility.9 In fact, the ductility reaches a maximum for alloys with compositions near to the limits of solubility. This enhanced ductility has been attributed to the lowering of the stacking-fault energy in the alloy; i.e., the increased amounts of twinning provide an additional mode of deformation, resulting in the observed high ductility.' Because of this demonstrated effect of rhenium in bee alloys, it was decided to study a series of alloys of Nb-Re. Using the same X-ray diffraction methods as described in the previous investigation,' one is able to identify the possible causes of broadening of the powder pattern peaks, e.q., particle size, microstrains, stacking faults, and/or twin faults. The separation of these various contributions to the measured peak shape is accomplished by the Warren-Averbach analysis.7 I) EXPERIMENTAL PROCEDURE A series of seven bee solid solution alloys containing from 2.5 to 21.5 at. pct Re (remainder niobium) were prepared at the General Electric Research Laboratory. Buttons, weighing 25 g, were alloyed from electron-beam-melted niobium chips and random rhenium sheet by arc melting in a water-cooled copper crucible, under an argon atmosphere. The buttons were inverted and completely remelted to promote homogenization. The nominal alloy compositions are listed in Table I. Samples of the cold-worked alloys were obtained by filing to produce a powder for the X-ray study. Alloys too brittle to be filed were hammered with steel plates. The resultant filings or brittle impactings were screened through 150-mesh classifiers and compacted to the required shape for the diffractometer holder. The X-ray diffraction peaks were automatically recorded by fixed time counting at uniform 28 intervals, or by continuous registration with a ratemeter. In all cases, the (110)-(220) and (200)-(400) pairs of peaks and the (211), (310), (222), and (321) reflections were measured on a GE-XRD5 diffractometer using CuKa radiation with nickel filter or MoKct radiation and a LiF monochromator in the diffracted beam. The first part of the data reduction, completed with the aid of a series of programmed computations,10 was the analytical resolution of the Kol component of the diffraction profile. Subsequent computations were then made with reference only to the resolved Kol peak shape. These included the measurement of the

Jan 1, 1967

By Robert J. Timko

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has re- searched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world, and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1986

By K. G. Wikle, J. G. Klein, W. W. Beaver

Consolidation of hydride process, electrolytic, calcium reduced, and comminuted thorium powder, as well as saw chips and lathe turnings, by vacuum hot pressing and by cold pressing-vacuum sintering was studied. The mechanical properties of the consolidated material in the extruded form are compared with those of wrought castings. AT present there little little industrial use for thorium metal, although it has some important though small scale applications in electronic equipment. Despite its high inelting point—about 1750°C —a low modulus of elasticity, 11.4xl0 si at 20°C;' relatively low mechanical properties coupled with a high density, 11.7 g per cu cm; and an unusually high chemical activity with normal atmospheres limit any structural applications. The metal is utilized as an alloying element principally in magnesium. Pure thorium finds utility as electrodes in gaseous discharge lamps such as the high intensity mercury lamp' because its low work function and high electron emissivity provide lower starting potentials and more uniform operating characteristics than other available materials. The metal is also found in photoelectric tubes used for the measurement of the ultraviolet spectrum." Thorium metal has been used in germicidal lamps of the cold cathode type as sputtered coatings on nickel in order to provide a low work function surface and a low starting voltage. Other applications have involved the radioactive properties of thorium for the production of ionized particles." The potential value of thorium is much greater than its present use pattern because of possible utility in the field of nuclear power. Th may be converted through nuclear reaction to a fissionable element U which should be capable of acting similarly to U in the g'eneration of atomic power. Thorium has been reported to be about three times as plentiful as uranium in the earth's crust, placing it in the order of abundance of lead and molybdenum." Thus, it is of interest in augmenting the potential supply of fissionable material for nuclear power. Because of its high melting point, thorium is usually produced as a powder through the calcium reduction of its oxide or thermal reduction of halides by sodium, magnesium, and calcium. It may also be produced in flake form by electrolysis of fused alkali or alkaline earth chloricles and fluorides. Therefore, powder metallurgy assumes importance in the fab- rication of thorium metal shapes. Furthermore, it is rather difficult to obtain pure thorium by melting, as the molten metal reacts readily with graphite as well as oxide, carbide, and nitride refractories. These contaminate the melt with oxides, carbides, and metallic impurities." The current investigation was undertaken to examine the fabrication of thorium by powder metallurgy methods which have been used for the commercial production of beryllium and other metals.' A sparcity of data concerning the comparative cold and hot compaction of thorium powders of different derivation existed. Therefore, all commercially available types were examined along with other experimentally produced thorium powders in order to round out the comparison of consolidated thorium powders with melted reguline metal. Review of the Literature By heating a mixture of ThC1, with potassium, Berzelius made the first thorium metal as an impure powder in 1828. Improvements in the basic process, increasing thorium assay to 99 pct, were made by several investigators including Arsem," Lely and Hamberger10 and Von Bolton." Calcium reduction of Tho, to make powders was investigated by Berger," Huppertz,'" Kroll," and Kuzel and Wedekind.'" A thorium powder produced by this method using a CaC1, fluxing agent assayed 99.7 pct, as reported by Marden and Rentschler.'" Compacted and sintered, this product was found to be ductile, and could be fabricated into wire and sheet. Improvements of the calcium reduction process were made later" wherein CaCl, was eliminated from the reaction, producing metal assaying 99.8 pct Th. Further work by Lilliendah118 howed that a coarser metal could be obtained by the substitution of ThC1, or ThOC1, for oxide with consequent advantage of stability to atmospheric reaction. Reports on the technology of thorium developed in Germany during World War II have been made by Espe."' Thorium powder of 99.5 pct Th was obtained by reduction of the oxide by calcium. Screening to —200 mesh, compacting with about 20 tsi, and sintering in vacuo at 1320" to 1360°C for 3 hr resulted in a porous sinter cake. The sinter cake was sufficiently ductile to be worked into bar, wire, and sheet which could be employed as electrode materials.

Jan 1, 1957

By G. U. Greene

The various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulphur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1)† states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As. Experimental Work In the present research, the author used for methods in an attempt to determine the composition of the various phases: (1) chemical, (2) microscopic, (3) roentgenographic and (4) thermal. Previous to this research, considerable time had been spent making analyses of different speisses, but unfortunately no very definite conclusions could be made as a result of these analyses.

Jan 1, 1937

By Dinesh Agrawal

Microwave energy has been in use for variety of applications for over 50 years. These applications include communication, food processing, wood drying, rubber vulcanization, medical therapy, polymers, etc. In the last two decades microwave heating has been also applied very effectively and efficiently to heat and sinter ceramic materials. Microwave heating is recognized for its various advantages, such as: time and energy saving, very rapid heating rates, considerably reduced processing cycle time and temperature, fine microstructures and improved mechanical properties, better product performance, etc. The most recent application of microwaves has been in the field of metallic materials for sintering, brazing/joining and melting. Several common steel compositions, pure metals and refractory metals have been sintered in microwaves to nearly full density with improved mechanical properties. Many commercial powder-metal components of various alloy compositions including iron and steel, copper, aluminum, nickel, Mo, Co, Ti, W, Sn, etc., and their alloys have also been sintered in microwaves producing better properties than their conventional counterparts by using a 2.45 GHz multimode microwave system. This work has been further extended to join and braze bulk metal pieces, especially super alloy based turbine blades. Further, in a specially designed microwave cavity, even the bulk metals can be made to couple with the microwave field and melted. The implications of these findings are obvious in the field of powder metal technology.

Jan 1, 2006

By T. F. Bower, M. C. Flemings, H. D. Brody

A series of experiments are reported which show thai reasonable assumptions for analysis of solute redistribution in solidification of castings and ingols illclr(de: negligible undercooling before nuclcation of solid phases, negligible increase of solute in advance of the tips of growing dendrites, complete diffusion within the Liquid oer distances the order, of dentrite arm spacings, platelike dentrite t/o?$holog?.. Qzmli/ali,e and periment is obtained JOY Al-Cu alloys front measurements of amount of nonequilibrium second phase, minimum solute content at the centers dentrites arms (after solidification), and 3) change in minimum solute content in dentrite arms during solidification. In a previous paper' analyses were given describing solute redistribution in dendritic solidification. The analyses were undertaken primarily to permit prediction of "severity of microsegregation" in a casting or ingot after solidification and cooling to room temperature, but can also be used to predict "local fraction solid' as a function of temperature in the solidifying alloy. Numerical results were given for Al-Cu alloys. The aims of this paper are to examine the validity of some of the assumptions of that analysis, and to compare predictions of the theory with experiments. All experiments reported are on Al-Cu alloys, the bulk on Al-4.5 pct Cu alloy. EXPERIMENTS Experiments conducted were on small ingots, 41/2 in. in diam by about 10 in. high. solidified in a controlled thermal environment (i.e., in a resistance-heated, re-circulating air furnace, whose temperature could be controlled to 1°C). In one series of experiments, the ingots were solidified very slowly (solidification time was varied from 8 to 1000 hr) and at constant rate of heat extraction. In a second series of experiments the ingots were solidified ( 'unidirectionally". Fig. 1 is a sketch of the method of making the two different types of ingots. The unidirectionally solidified ingots were fully columnar, and the slowly solidified ingots had equiaxed structures, Fig. 2. In making the slowly solidified ingots, the mold employed was carbon steel, coated with inert refractory. Typically the mold and its environment were heated to 700°C. The molten alloy was then poured into the mold and the temperature of the system equilibrated above the liquidus. The environment of the mold was next cooled with a controller responding to a differential thermocouple that measured the difference between the temperature of the melt and the temperature of the mold environment. The differential thermocouple consisted of one chromel-alumel junction in the melt connected in opposition with a second junction in the furnace. The potential across the differential thermocouple was input to the controller which acted to keep this potential at a set. constant value; hence the temperature difference between the two junctions was maintained nearly constant. Major resistance to heat flow in the above apparatus was between the metal surface and the furnace atmosphere, not in the metal itself. By maintaining a constant temperature difference between the metal and the furnace atmosphere, the controller maintained an essentially constant rate of heat extraction during solidification, regardless of amount of heat released by the metal per unit temperature change. When the metal temperature dropped just below the eutectic temperature. the ingot was removed from the furnace and water-quenched. The unidirectionally solidified ingots were cast in a similar mold to the foregoing except that provision was made to extract heat through the bottom face of the mold by passing air or water through the mold base, Fig. 1. For these experiments, metal and mold temperature were again equilibrated above the liquidus. Temperature of the mold environment was then held

Jan 1, 1967

By R. K. Iyengar, G. C. Duderstadt

An investigation was carried out to determine the effect of Ca-Si additions on the dissolved oxygen content of liquid steel. An apparent equilibrium was reached after holding the melt for some time when the total oxygen content of the melt was identical with the dissolved oxygen. Results of the investigation show that for deoxidation with silicon and manganese the apparent equilibrium is reached after 8 to 12 min and the oxygen content of the melt is in good agreement with values reported in the literature for similar steel compositions. Ca-Si additions decrease the dissolved oxygen content appreciably below that obtained with Si-Mn deoxidation. It is postulated that some calcium dissolved in liquid steel at the time of its vaporization combines with dissolved oxygen to form CaO which then fluxes the manganese silicate, thereby lowering the activity of the deoxidation products. Slow flotation of calcium silicate inclusions is attributed to their slower growth rate. An addition of aluminum (to yield <0.005 pct Alsol) prior to introduction of Ca-Si improves the kinetics of removal of resulting deoxidation products. WITH the introduction of continuous casting of billets and blooms, application of calcium-containing alloys for deoxidation purposes has gained new interest. More so than in conventional ingot casting, the degree of control of the dissolved and total oxygen contents in steel for continuous casting can determine the success or failure of the operation because these affect both surface (pinholes) and internal quality of the billets. Of the available deoxidizers, only silicon has so far found wide application. However, in the typical range of application (0.20/0.30 pct Si), it is too weak a deoxidizer to suppress pinhole frequency to the level desirable for all but the least demanding appli-cations (approximately 10/50 pinholes per sq ft, de-pending on degree of subsequent reduction). On the other hand, Vincent&apos; has shown that it requires ap-proximately 0.007/0.008 pct A1 soluble in the steel to suppress pinhole formation to <10 pinholes per sq ft. In view of the difficulty of consistently maintaining this aluminum level and the associated problem of tundish nozzle constriction2 when aluminum is added to the ladle, steelmakers have searched for other de-oxidation alloys to circumvent the problem. Calcium-containing alloys offer such a possibility. When employed as a partial substitute for silicon, CaSi (30 pct Ca/60 pct Si) additions are reported to yield adequate pinhole contro1.3 Its use simultaneously preserves the "fluidity" of the steel and ensures good castability.4 Oxygen contents as low as 0.007 to 0.014 pct have been obtained with CaSi additions varying between 3 to 8 lb per ton.5-7 Due to the high degree of vaporization of calcium at the temperature of molten steel and the different methods used to introduce it into the liquid, the reported results show considerable scatter and lack of consistency. According to several investiga- deoxidation tors, the flotation characteristics of CaSi products are not as favorable as those found for alumi-num but are similar to those established for silicates with low alumina content.678 Thus, cleanliness ratings were improved when CaSi was replaced by a com-bination of Si + A1 followed by CaMnSi additions.5,9 In view of the lack of a comprehensive description of the deoxidation potential of CaSi alloys, a study was undertaken of the effect of CaSi additions on oxygen content in comparison to Si + Mn and Si + Mn + Al. The alloy chosen for this study contained 63 pct Si, 32 pct Ca, <3 pct Al, and 2.5 pct Fe. EXPERIMENTAL PROCEDURE The experiments were divided in three groups as shown in Table I. In each group, the CaSi addition was increased successively while maintaining the melt composition constant. The experiments in the third group were designed to determine the effect of prede-oxidation with small amounts of aluminum. Ingot iron, containing 0.02 to 0.03 pct C and 0.03 to 0.05 pct Mn, was melted in a 100-lb magnesia crucible. Pig iron was added to the melt under air in an induction furnace to attain the desired carbon content of 0.05 to 0.15 pct and thereby control the initial oxygen content of the melt between 0.04 and 0.015 pct. After removal of the slag, the furnace was sealed and argon was introduced through an opening in the graphite cover, Fig. 1. When the desired temperature was reached, electrolytic manganese was added to the melt and pin samples were taken (7 mm silica tubing) to establish initial oxygen content. To obtain maximum efficiency, CaSi and metallic silicon were introduced in a sealed steel pipe into the bath. This procedure assured minimum loss of calcium through vaporization as the deoxidants were always released at the bottom of the melt. Samples were taken at regular intervals and quenched in water. Temperature of the bath was measured with a Pt/Pt-10 pct Rh thermocouple. Portions of the pin sample were used for oxygen analysis; five determinations per sample were made to obtain average oxygen content. Oxygen analyses were made by the inert carrier gas fusion method with frequent cross checks with the vacuum fusion method.

Jan 1, 1970

By L. von Ketelhodt

Dual energy X-ray transmission (DE-XRT) sorting is a recent development in the range of sensor-based sorting technologies available today. DE-XRT is particularly suitable for dry coarse coal beneficiation in the size range -120 mm +12 mm. In this paper, we describe the technology and show the results of a number of test runs conducted on different types of coal from the USA and South Africa. The results have shown that DE-XRT is an effective technology not only for deshaling of coal and removing pyritic sulphur but also for separating coal and torbanite. The use of dry deshaling methods will be more important as water availability becomes a greater concern. DE-XRT is one such technology which will be incorporated in future dry coal processing plants.

Jan 1, 2010

By J. W. Graham

For many years the author has been cognizant of the difficulty encountered by some in treating with the water influx formulas for unsteady-state fluid flow as pertain to the material balance equation. This has particularly applied in establishing reservoir performance and identifying reservoir pressure, which to the practicing engineer has entailed a trial-and-error procedure, and for others has necessitated resorting to computing devices and reiteration processes. In retrospect this difficulty stems from the fact that reservoir pressure in the material balance formulas, as well as associated with the water influx equations, is an inexplicit term, and the work reported in the past is irrefutable. However, what will be presented in this paper is another approach to the problem, whereby the entire material balance equation will be treated by the Laplace transformation, and reservoir pressure which hereto has been inexplicit, can now be isolated by mathematical procedure to relate that parameter with all the factors contributing to its change. This is the simplification entailed, that treats first with an undersaturated oil reservoir as an integrated effect from the inception of production. The second phase pertains to saturated oil reservoirs that encompass a survey traverse. Although both methods of approach are necessarily different in aspect, the most interesting fact is that the mathematics so deduced are identical. Both the linear and radial water-drive systems are incorporated. for which an illustrated factual example is offered for the latter, treating with a saturated oil reservoir. INTRODUCTIO N What is performed in this work is the simplification of an involved computation by advanced analysis. Although such may be construed as a contradiction when one treats with higher mathematics; nevertheless, when direction is given to such an undertaking the results car. be most revealing. Likewise, it is to be mentioned that the bases for these mathematics have been developed on the expediency of the occasion. This is not to be inferred as a qualification of this work, but rather the demands frequently placed upon the author in his private prac- tice in meeting a time limit. A situation, instead of being fraught with hazards, often has given emphasis to creative thought. What will be entailed in this work is the simplification of the material balance formulas by the Laplace Transformation., Although this reveals entirely new horizons that will be given expression in a forthcoming tract, it suffices in the present instance to limit our attention to this phase of the development that treats both with an undersaturated and saturated oil reservoir. To orient the reader&apos;s thoughts as to what is involved in this simplification is the recognition that reservoir pressure, as such, is an inexplicit term in the material balance equation. This is the independent parameter that defines the total history of performance in the author&apos;s&apos; unsteady-state water influx formulas, as well as the basis for the physical dependency of fluid behavior within the formation as prescribed in the Schil-thuis&apos; material balance equation. Therefore, to isolate reservoir pressure, which is the most essential factor in any reservoir study, is rather a cumbersome procedure entailing either a trial-and-error calculation for the engineer; or as some prefer, a reiteration process performed on a computing device. However, once such an equation can be transcribed as a Laplace transformation, this inexplicitness so expressed can be alleviated to identify reservoir pressure as an explicit function of all the factors contributing to its change. This is the simplification encompassed, that will treat first with an undersaturated oil reservoir as an integrated effect from the inception of production, and secondly, with a saturated oil reservoir as a survey traverse. Although the two approaches are necessarily different because of the uhvsics involved. it is an interesting commentary that the mathematics are identical, showing the interdependency of the two methods. In order to acquaint the reader with this development, the simplest case will be treated first; namely, an under-saturated oil reservoir subject to a linear water drive. However, what may be construed for this example as an idealistic case is actually a most practical application in certain parts of the world, where the size of the fields are so large that radial water-drive approaches the configuration of a linear drive. Further, to avoid the repetition of much symbolism, frequent references will be made to the work of the author and an associate on Laplace Transformations3,

By J. Murray Riddell, Arthur E. Anderson, Grover J. Holt

OUT of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the seasor1 of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in low gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1938

By Leon Eliel

TEN years ago .a broad knowledge of aerial mapping, coupled with a smattering of geology, qualified one to speak on the subject of the appli-cation of aerial mapping to geology. Today, with aerial maps a common tool in the hands of expert geologists on every continent throughout the world, it would be nothing short of presumptuous for the author of this paper, who is not a geologist, to give any geological statements on his own authority. Relatively, today we are only purveyors of general geological gossip, with a definite case here and there by way of illustration. But we can present a story of the really marvellous strides that have been made in the evolution of aerial mapping, built around a skeleton of geological tidbits, from which some useful conclusions may be drawn. The average geologist goes about reading his aerial maps much as one would approach the problem of deciphering a cryptogram. To begin with, typical key expressions appear in recurring sequences and under certain conditions. If once the meaning of these. isolated bits of infor-mation can be ascertained, the message begins to take meaning.. In a similar fashion, the geologist works out his key from aerial maps of territory with which he has some familiarity. He learns that a certain type of thin, white line may mean a vein of quartz. He sees that a certain change in the photographic tone of vegetation on the ground reflects two kinds of soils on opposite sides of a contact. He sees that a certain type of alignment of topographical features often means a fault. He learns that by the erosion pattern he can frequently distinguish soft formations from harder ones. And so, bit by bit, he ties together the information of the picture with his experience on the ground until he develops a reasonably creditable capacity of interpretation. Through the complete gamut of surface conditions, ranging all the way from flat, arid, exposed desert terrain to dense jungle, or rugged mountains, the evidence from which the geologist must make his inter-pretation varies with bewildering profusion. The quality of photographs which are obtainable may range from perfect pictures in the desert to almost useless smudges in the steaming jungles. One thing he has learned with certainty-the airplane carrying its mapping camera is a superb reconnaissance tool, only awaiting his ingenuity in correlating the pictures with the ground to simplify most exploratory problems.

Jan 1, 1936

By Gareth Thomas

The analysis of Kikuchi pattersns of exct ovientalions from single cryslals and paired Kikuchi lines from single and overlapping crystals is shown to be useful and quanlitalve and is applied to Phase transfovnzcitions including ordering, spinodals, mavten-silic, and nuclealion and growth pyocesses. 112 pinciple, the analysis of exacl orientations enables the crystal system and the Bravais lattice of a crystal to he determined. The advantages of the davk-field imaging technigure for detecting vevy small precipitates are also described. ALTHOUGH Kikuchi electron-diffraction patterns were first observed nearly 40 years ago,&apos; little systematic application seems to have been made of them, until fairly recently during electron microscopy, when their usefulness in contrast experimen and for determining exact orientations8&apos;9 has been pointed out. With the availability of gonio-metric specimen tilting stages it has now become possible to make much wider use of diffraction patterns, particularly the Kikuchi pattern, which is the main subject of this paper. The treatment presented here is not exhaustive but it is hoped that it will stimulate more use of Kikuchi patterns during electron-microscopy investigations. The Kikuchi pattern is formed as a result of Bragg diffraction of the inelastically scattered electrons produced during the interaction of the beam and thick specimens, The important feature of these patterns is that they give an accurate representation of the symmetry of the crystal being investigated, so that it is possible to identify crystal systems and even the Bravais lattice. This means that new structures, e.g., formed in phase transformations, may be identified during normal electron microscopy, so that Kikuchi-pattern analyses considerably extend the uses of the electron microscope. Recent work has also shown that dark-field images are more informative than bright-field images, particularly, for observing small precipitates. The second part of this paper discusses some applications and advantages of dark-field imaging in studies of two-phase systems. 1) DIFFRACTION PATTERNS 1.1) Spot Patterns. Electron-diffraction spot patterns have their limitations because of the importance of the form factor on the intensities and shape of the reciprocal lattice points. Because of the extension of these points into relrods, reflections are possible over a large angular range (+5 deg) and the patterns from thin regions can be complicated because second-layer relrods intersect the reflecting sphere. Spot patterns can thus give only an approximate idea of the crystallography unless the foil is tilted into exact orientation. In this case the spot pattern is symmetrical, with equal numbers of spots on the positive and negative zone directions about the origin. Such cases are necessary for structural analyses and have been used recently to determine the crystal structure of the ordered Ta64C phase." Exact orientation means that the plane of the reciprocal lattice lies exactly normal to the incident beam as shown in Fig. 1(b). It should be noted that in exact orientations the angle of reflection is less than the exact Bragg angle 9 so that the reciprocal lattice points lie to the outside of the sphere, Fig. 1(b). This deviation is denoted by the parameter s and in the usual convention4 s is negative for exact orientations and, of course, zero at the exact reflecting position shown in Fig. l(a). In order to avoid secondary reflections from thickness relrods it is advantageous to work in thicker regions of foils. Diffraction from thick regions may also produce Kikuchi patterns and as dis-

Jan 1, 1965

By Billy L. Crowder, John M. Fairfield

The implantation of B+ , P+, and As&apos; into silicon has been studied with the purpose of making shallow p-n junctions. The influence of such parameters as 1) ion energy, 2) target orientation and temperature, 3) total dose, and 4) annealing schedule was investigated. An energy range of 70 to 300 kev was used for boron and phosphorus implants and up to 500 kev for arsenic. It is found that the experimental projected range agrees well with theory and that shallow junction depths can be made reproducibly. ION implantation has received much attention recently as a technique for doping semiconductors. Specifically, it has the potential of supplementing or replacing the diffusion process as a method for making p-n junctions. In a few specific cases it has been used successfully to make semiconductor junction devices. Potential advantages of ion implantation doping over diffusion techniques are: 1) It affords greater control of shallow junction depths (< 0.2 µ) while maintaining high peak concentrations. This is particularly important for high-speed switching devices, since lower junction capacitances and resistances can be achieved. 2) More precise registration of small planar structures can be realized if proper masking procedures are employed. This advantage is especially useful in the design of high-density integrated circuits. It has been used to advantage in FET fabrication since the edge of the source or drain can be aligned precisely at the edge of the gate electrode.&apos; 3) Ion implanatation permits lower temperatures than diffusion techniques. This factor alleviates the problem of compatibility of diffusivities often encountered when designing multiple-junction structures. Also, the lower temperatures create fewer thermal defects and dislocations, which may account for the high efficiency of some ion-implanted solar cells.2 4) Impurity profiles can be more easily tailored to resemble ideal distributions. Successful exploitation of the potential advantages of ion implantation techniques will depend on increased knowledge and understanding of the subject. The factors likely to be influential in determining impurity distribution profiles in ion-implanted single-crystal targets have been reviewed by J. F. Gibbons.3 In addition to the mass and energy of the implanted ion, the total dose, target orientation, and target temperature are important parameters. The annealing temperature required for removing lattice damage and incorporating the implanted species on an electrically active site is very important. This paper describes an investigation of some of these factors. Implants of boron, phosphorus, and arsenic into silicon have been studied. Energy ranges of 50 to 300 kev were used for boron and phosphorus and up to 500 kev for arsenic. In addition to the implantation energy, the effects of total dose, target temperature, and post implant anneal have been investigated. EXPERIMENTAL PROCEDURE The implantation targets were silicon wafers cut from Czochralski-grown crystals, lapped, and chemically polished. The orientations were (111), (110). and (100) with misorientations of up to 7 deg from the principal axis. For this study, accurate target alignment (i.e., within 0.1 deg) was not available and quoted misorientation values should be regarded as approximate . The implantation equipment consisted of an ion source, a 300-kev linear accelerator tube, an electromagnetic separator, and the associated target supporting and beam focusing assemblies. The ion source was a simple oscillating electron type source,4 which has been described elsewhere.5 The gaseous compounds BF3, PF5, and AsH3 were used as ion sources for B+, P+, As+, and AS+&apos;. Analyzed current levels of up to 20 pamp could be obtained; however, for this investigation target current levels of 1-3 µ amp were usually employed. The analyzed ion beam was collimated through a double slit (1.4 x 0.4 cm) and swept perpendicularly to the long axis of the slit such that an area of about 2 sq cm on each target was covered. Dosages of around 1015 cm-2 were normally employed, but smaller amounts were also used for comparison. A uniform flux density over the bombarded area was assured by the continuous use of profile monitors similar to those described by Wegner and Feigenbaum.6 Post-implant annealing was accomplished in an argon atmosphere in a temperature range of 600" to 950°C. It was not part of the purpose of this investigation to study the annealing kinetics; however, some isochronal and isothermal anneal experiments were conducted to determine the time and temperature necessary to render a reasonably high portion of the implanted ions electrically active (i.e., higher than 50 pct). Post-implant anneal temperatures of around 900° and 600°C were required for boron, and arsenic and phosphorus implants, respectively. Arsenic and phosphorus implants increased in conductivity rather abruptly at the proper anneal temperature of the isochronal curve, but boron increased more gradually over a wider range. Isothermal anneal curves were reasonably flat after 10 min, so an anneal time of 1/2 hr was used for the experimental results described below. The profiling techniques were: 1) neutron activation analysis, 2) differential sheet resistance,7 and 3) junction staining.8 The differential sheet resistance technique is commonly employed in this type of study. Its principal disadvantage is the uncertainty of the ef-

Jan 1, 1970

By R. K. Ham, M. L. Wayman

TD-Nickel has been broken in tension and in fatigue at voom temperature. Rod specimens failed in tension by necking, with axial cracks attributed to voids elongated in the extrusion direction. Fatigue specimens failed in shear. Thin-film electron microscopy showed that the subgrain structure of TD-Nickel was very stable, and that particle-matrix detachment was very difficult, in tension and fatigue. TD-Nickel softened slightly during fatigue but had a high fatigue ratio (0.5at 10&apos; cycles). Fractography suggested that Stage I fatigue crack propagation is greatly extended in TD-Nickel. Td-NICKEL* is a dispersion of 2 pct by volume of thoria (ThO2) in nickel, produced by powder-metallurgical methods including compaction, sintering, and extrusion. The spherical thoria particles, which may have a mean diameter of a few hundred angstroms, are dispersed with a mean planar spacing of a few thousand angstroms. By a combination of cold working and annealing, a subgrain or cell structure of dislocations intimately associated with the dispersion can be produced.&apos; This gives the material useful tensile properties which are extremely resistant to exposure to high temperatures.&apos;-= At the same time, the material shows considerable ductility.3&apos;4 At the beginning of the present work, it was considered of great interest to investigate the mechanical stability of TD-Nickel under conditions of fatigue. On the one hand, materials which derive strength from a cold-worked structure are unstable in that they are susceptible to fatigue softening: in addition, the presence of discontinuities such as the particle-matrix interfaces might be expected to assist in the initiation and propagation of fatigue cracks, in that they may provide local concentrations of internal stress and sites for the initiation of voids." On the other hand, the substantial ductility of TD-Nickel suggests that if it obeys Coffin&apos;s relation8 (or the more refined form proposed by Manson9) it should have good fatigue resistance. The initial purpose of this investigation was to assess the importance of these factors. Also, relatively little fundamental work has been done on the mechanism of fatigue in dispersion-strengthened materials. Work on overaged A1-4 pct CU10-12 revealed a very large Bauschinger effect indicative of internal stresses at the particles, and very great fatigue hardening1&apos; presumably due to the multiple slip stimulated by these internal stresses, followed by softening which was initially due to softening in the matrix, but later might have arisen from cracking at the particle-matrix interfaces. The study of overaged Al-4 pct Cu could not settle this latter point by the electron microscopy of thin films, since the dispersion is too coarse. A previous study of the fatigue of internally oxidized copper13 was complicated by inter granular failure, attributed to oxide particles at grain bouhdaries; internal oxidation of single crystals, however, improved their fatigue properties.&apos;3 Investigations of SAP (sintered aluminum powder) are complicated by the complex particle shapes, and the possibility of continuous internal oxide films.14 It was hoped to avoid these difficulties with TD-Nickel, which had the further advantages that it was commercially available and suitable for study by the thin-film technique. 1) MATERIALS AND EXPERIMENTAL PROCEDURE TD-Nickel was purchased from the Driver-Harris Co. as 3/9-in.-diam rod which had been extruded, swaged, and "stress-relieved" (normally at 1010°C for 1 hr). Continuous-radius fatigue specimens with a minimum diameter of -0.1 in. were ground to shape and electropolished in 40 pct phosphoric, 35 pct sul-furic, 25 pct water at 25oC, with a stainless-steel cathode, at -6 v. Fatigue tests were carried out at room temperature with a Sonntag SF-1-U machine operating in push-pull at 1800 cycles per min, and in an Instron TT-C-L modified for reversed stressing at 26 cycles per min as described elsewhere.10 Round tensile specimens were ground with 0.85-in. gage lengths of 0.135 in, diam, electropolished, and tested in a Tinius Olsen hydraulic machine. The surfaces of fatigue specimens were examined with a Reichert metallograph. Discs for electron microscopy with a Siemens Elmiskop I were spark-cut 0.01 in. thick with a modified Servomet 11 employing a tool of moving molybdenum wire, cleaned in 50 pct acetic, 30 pct nitric, 10 pct phosphoric, and 10pctsul-furic at 85oC, and thinned by the window method in the electropolishing solution at -20°C and -6 v. Two-stage replicas (parlodion, then Pt-50 pct C self-shadowed at 40 deg) were taken from fatigue fracture surfaces for electron microscopy. Plane sections parallel to the specimen axis and containing the direction of fatigue crack propagation were polished, etched with Carapella&apos;s reagent, and examined optically. Transmission Laue X-ray photographs of as-received material electropolished to a point were used to determine preferred orientation. 2) RESULTS 2.1) The Structure of As-Received Material. Grains -1 µ diam and elongated 20 to 30 u in the direction of the rod axis were observed, With&apos; elongated "intergran-ular" voids (-4 p diam and -90 µ long and identified as such using longitudinal and transverse sections and

Jan 1, 1968

By J. L. Lamon, W. Crafts

Study with the electron microscope of the carbides in vanadium-chromium-molybdenum steels after tempering up to 1000 hr at 600 teelsto 1400°F confirmed that alloy carbides are formed at the secondary hardening temperature by decomposition of the plate-like iron carbides. It was also demonstrated that vanadium carbide persists as much smaller particles than do chromium- or molybdenum-bearing carbides. Conditions conducive to the formation of fine vanadium carbides are indicated to be favorable for high temperature strength. IN order to determine the effects of long exposure at high temperatures on vanadium-bearing steels, a survey has been made of their hardness and carbide structure. The behavior of carbides in the tempering of martensite was studied by X ray diffraction and electron microscope examination of electrolytically extracted residues in greater detail than in an earlier investigation.&apos; A group of steels with about 0.25 pct carbon and containing chromium up to 5 pct, molybdenum up to 1 pct, and vanadium up to 1 pct was either quenched or annealed and then tempered for peri- ods of up to 1000 hr at 600° to 1400°F. Their hardness after tempering agreed with the Hollomon and Jaffe2 relation of equivalency of time and temperature, and with the degree of secondary hardening predicted from composition. Further, the appearance of the carbides indicated that the time and temperature equivalency relation was also applicable to the degree of carbide development. The mechanism of the tempering of martensite was demonstrated more clearly than in the earlier study. It was confirmed that carbides develop from martensite as poorly defined plates of the Fe2C type carbide followed by thickening of the plates with a transition to Fe,C. Finally the plate structure deteriorates into a lacy mass from which alloy carbides emerge as chunky particles that grow slowly with further increase of tempering temperature. Vanadium carbide derived from tempered martensite was found in characteristically small particles that tended to grow very slowly. The addition of chromium or molybdenum to a steel with predominant vanadium carbide tended to introduce carbides of a chromium- or molybdenum-bearing type having a somewhat larger particle size. The Cr,C, type carbide particles were larger than those of the V,C, type and somewhat smaller than the carbides in steel containing both Cr,C and M,C. Similar observations were made of the carbides in the pear lite of annealed steels. It appeared that high temperature properties would be benefited by the retention of the fine carbide particles that result from a balance of composition and heat-treatment designed to produce a maximum amount of vanadium carbide. Procedure: The steels used in the investigation were made with a base of Armco iron in a high-frequency furnace at the Union Carbide and Carbon Research Labs., Inc. The steels were deoxidized

Jan 1, 1951

There are two mechanisms in the flo- tation process by which particles are transported from the pulp to the con- centrate: bubble-mineral aggregation and entrainment. It is the chemical processes which occur in the pulp which are critical to the success of flotation since they control the floatability of different min- erals and the selectivity which can be obtained. However, these chemical pro- cesses are so complex that metallurgists are still limited in their ability to predict the floatability of particles in industrial circuits by consideration of the minerals present and the chemical environment. The alternative approach to understand- ing flotation is to examine the behaviour of minerals in industrial flotation pro- cesses, to recognise similarities and differences, and to define the "laws" which appear to apply. Using this ap- proach it has been found that minerals float at a rate which is proportional to their concentration in the pulp, and that the rate of flotation of different min- erals is influenced by variables which&apos; affect the pulp or the froth phase. The ultimate application of this approach is the use of models for circuit simulation purposes. It is this alternative approach which is the theme of this paper. One of the most important problems in understanding the technology of flotation has been in defining the characteristics of the particles being floated. Particles entering flotation vary widely in size and mineral composition, and different par- ticle types float at different rates. These rates do not change uniformly as operating variables change. It has been conventional practice to assess flotation performance in terms of the metal contents of total streams because no better method has been available, and this procedure has obscured important effects which occur in

Jan 1, 1984

By Takahiko Okura, Chiharu Tokoro, Shunta Shibuya

Copper concentrates bearing arsenic as enargite (Cu3AsS4) or tennantite (Cu12As4S13) have disadvantage on copper smelting environmentally and economically, so those concentrates should be treated decently. In this paper, some experiments of arsenic removal from several kinds of copper concentrates by heat treatment in an inert atmosphere were discussed. In this study, several samples in which arsenic contents varied 0.18 to 8.3 wt % were heated to the temperature range of 400 °C to 700 °C under argon gas flow during 1 hour. The heat residues and volatilized materials (V.M.) were analyzed by XRD, XRF, ICP-AES, XAFS and MLA to analyze residual concentration of arsenic and residual mineral composition. Experimental results showed that arsenic removal from copper concentrates advanced in 2 steps; at the temperature range of 500 ° C to 550 °C and of 550 °C to 650 °C, respectively. MLA analysis showed that a few of arsenic in enargite was removed by 550 °C heating and a majority of it was still combined with copper and sulfur as tennantite. On the other hand, arsenic in tennantite was removed almost completely by 650 °C heating. Furthermore, a particular type of arsenic mineral, such as Cobaltite (CoAsS) still remained after heating at 700 °C.

Jan 1, 2014