Search Documents

By J. Vander Linden, R. De Ketelaere, M. Verhaege

In this paper, results are presented concerning the search to implement Supported Liquid Membrane (SLM) technology for the recovery of copper from electroplating effluents. Acid copper electroplating rinse solutions or effluents resulting from the post-treatment of, for example, cyanide-containing copper electroplating baths all contain copper (2+) in the lower concentration levels. A thorough study of the influence of the individual parameters and of their combined impact on mass transfer in small scale laboratory SLM modules has been performed, enabling to set forward the appropriate operating conditions for a pilot plant installation. The pilot plant, containing two SLM modules. of 18 m2 of surface area, has been tested extensively, including short and long term runs, with real process solutions. It was demonstrated that this installation is able to treat 40 l/h of acid copper sulphate rinse solutions· containing 500 ppm of copper. The final copper concentration in the effluent can be reduced to a few ppm while copper metal is recovered by electrolysis of the concentrate. This technology is also applicable to the treatment of solutions with low copper content of origins other than plating shops, such as tailings from copper plants or mine waters.

Jan 1, 2000

By J. Hansen

"ABSTRACTThe paper addresses the application of automated monitoring, control, and navigation to improve dragline performance. SummaryImproving dragline performance in the Canadian coal mines is critical to the continued success of the industry. Draglines represent a large capital investment and coal prices are low by historic standards. This paper argues that the introduction of monitoring, control, and navigation on draglines offers an opportunity to significantly reduce a dragline’s operating cost per cubic metre moved. To place the importance of this in perspective, a North Dakota mine calculates that every 1% increase in dragline productivity means a savings to the mine of US$340,000 per year. MonitorsAutomated dragline monitoring is a well established technology with commercial products available since the early 1980s. The three main reasons for placing monitors on draglines are (Walker, 1993):1. productivity increases: reduce variations between different operators’ performance across different shifts;2. quality increases: increase the percentage of ore and waste loads that go to the correct destination; and3. special projects (engineering projects): justify installing static field exciters and regulator upgrades; implement power management; aid operator training; study high performance buckets, rigging changes, and various excavation sequences.Mines as diverse as Kennecott’s Cordero- Rojo Complex in the United States and Natal Coal Corp.’s Optimum Mine in South Africa report dragline productivity increases of 10% to 20% in the region attributed to the implementation of dragline monitoring."

Jan 1, 2000

James Barnes is Managing Director of James Barnes & Associated Ltd which is a company that has invested ten years of development to provide developers with a transparent, user friendly consultation framework that identifies who needs to be consulted, how they are to be consulted and procedures required to manage the risks associated with getting all the wrong! Despite the assertion above, this paper is not about to provide delegates with the answer to whom they ought to consult or identify the expectations that Maori might have in regard to the consultation process. It would be a very brave person indeed who would venture an opinion on such a sensitive subject. There are no short cuts to finding out what expectations Maori might have on any given situation. Nothing can be taken for granted. What this paper will attempt to do however is provide practical insights into what might be on the minds of Maori interests as they deal with the issues associated with mineral resources, particularly those under Treaty of Waitangi Claim. The Treaty of Waitangi has a significant bearing on the current debate between Maori and the Crown regarding ownership of mineral resources in New Zealand. The Waitangi Tribunal is currently hearing a case presented by a number of Iwi over the ownership of oil and gas resources in Taranaki and Hawkes Bay. Others will follow. The Crown and Maori have never been able to settle differences over ownership rights without resorting to legal action and it looks like this scenario is about to be repeated in regards to minerals. The Crown has a duty to actively protect the Maori interest. This is a fundamental expectation in the relationship between Maori and the Crown. In the case of minerals, Maori have yet to see the Crown do its duty. The impact on developers has become evident through Maori objections to consent applications as the issues of mineral right remain unresolved.

Jan 1, 2000

By Masaru Tomoguchi, Tom Nishiyama, Naoto Sasamoto

"In Hanaoka Mine, which was one of the major ""black ore"" (Kuroko) mines in the north part of Japan, mining has finished in 1994, and only mineral processing plant is available now. Recently this mineral processing plant has been applied to the soil washing. Soils contaminated with heavy metals are excavated and transported to the plant. The soils are separated to cleaned soil and metal enrichment through the process which consists of scrubbing, classification, extraction, insolubilization, flotation, and so on. The process is flexibly designed for each contaminated soil, in order to the products can be recycled as cleaned soils or metal sources. . Soils contaminated with arsenic and lead were treated in 1999, which were entrusted from Environmental Agency of Japan.IntroductionDowa Mining has had the mine site named ""Hanaoka Mine"" and ""Kosaka Mine"" in the north part of Japan. Those mines consisted of some ore deposits and produced ""black ore"" (Kuroko) and ""yellow ore"" (Oko), which are complex sulfide ore. The ""black ore"" mainly consists of sphalerite, galena and barite with accessory chalcopyrite, tetrahedrite and Au, Ag minerals. The ""yellow ore"" mainly consists of powdery and clayey ore containing chalcopyrite and. pyrite, with a little sphalerite and galena. Each mine site had mineral processing plant respectively, ""Hanaoka Mine"" had two and ""Kosaka Mine"" had one plant. Those plants were operated by flotation process to separate each mineral, and produced concentrates of copper, lead, zinc, pyrite, barite and so on.Unfortunately, the mine had closed one by one because of change in economical circumstances and the lack of ore reserves. Mill plants were also closed and dismantled, but the last ""Matsumine mill plant"" of Hanaoka Mine was remained to be utilized usefully. In the circumstance like that, we came across with soil remediation business. Recent reports say that subsurface contamination in Japan is being grown substantially and that it can be a serious matter beyond the imagination of our society. So nowadays we have a tendency to pay attention to the environmental issues including subsurface one."

Jan 1, 2000

By Masayuki Kudoh, Tohru Maruyama, Yohichi. Ito

When hypo-peritectic carbon steel is quenched during unidirectional solidification, the region of fine columnar grain is observed. It is classified into two coexisting phases. One is coexisting phases of liquid, delta and gamma in the upper part of the region, and the other is coexisting phases of delta and gamma in the lower part of the region. To form the coexisting part of the three phases means that solidification in this experiment proceeds in non-equilibrium state. The size of the narrow side of one fine columnar grain coincides with the arm spacing of a primary dendrite and this result is the same as the hyper-peritectic carbon steel. However, the boundary of the fine grain in the hypo-peritectic carbon steel is formed in different location from that of the hyper-peritectic carbon steel. The former is formed in the skeleton of the dendrite, while the latter is formed in the interspacing of the dendrite. The region of the fine grain changes suddenly to that of the coarse grain when the delta phase in the coexisting part of two phases disappears completely. Therefore, the delta phase in the hypo-peritectic carbon steel might prevent the growth of gamma grain. In order to recognize it, ferrite formers such as Mo, V and Ni are added in the sample. Then, the longitudinal length of the fine columnar grain extends in the sequence of the no addition, Mo, V and Nb.

Jan 1, 2000

By Kathleen S. Smith, Katherine Walton-Day, James F. Ranville

Four different scales of observation were used to evaluate the potential effects of a fluvial tailings deposit on water quality along the flood plain of the upper Arkansas River south of Leadville, Colorado. First, we collected surficial material and subjected it to batch water-leaching test. Second, we excavated and leached an intact eight-inch diameter core. Third, we examined the water quality of the shallow ground water beneath the fluvial tailings deposit, and fourth, we monitored water quality along a 5-km reach of the adjacent Arkansas River. Leaching of surficial samples indicates that there is a reservoir of readily water-soluble material yielding elevated metal concentrations and high acidity. However, there are minimal measurable water quality effects of the fluvial tailings deposit on the adjacent reach of the Arkansas River.

Jan 1, 2000

By R. L. Guerguerian

Nowadays, most grinding mills driven by a wrap-around ring motor are operating successfully. Some of the earlier problems could be attributed to the lateral stiffness and stability of their bearings. As a result, modifications to the bearings included the rearrangement of the shoes, or the addition of more shoes, closer to the horizontal centerline. This technical paper reports a study of the effects of bearings on the lateral stiffness of grinding mills driven by a wrap-around ring motor. The discussions cover the design of the four shoe trunnion bearings and examine the effects of the angular location of the shoes.

Jan 1, 2000

By E. J. Beckman, R. M. Enick, C. Shi

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. Two inexpensive and environmentally benign fluids were selected for the study, water and carbon dioxide. The separation, which is conducted at 295 K and at the vapor pressure of carbon dioxide (6.0 MPa), is based on differences in wettability between the precious metals and other minerals. Contact-angle results indicated that, in the presence of water and liquid CO2, gold is slightly hydrophobic. The addition of CO2-soluble fluoroalkyl thiols or f uoroetherthiols increased the hydrophobicity of gold exposed to water and CO2 to a greater extent than alkylthiols. Minerals, including quartz, pyrite and magnetite, were hydrophilic. During the separation, an aqueous slurry of fine mineral and gold particles was mixed with liquid carbon dioxide. Pure gold particles (-325 mesh) were found to agglomerate at the H2O-CO2 interface. The minerals tended to remain in the aqueous phase. Despite these promising preliminary results, very poor gold recoveries were obtained when applying the procedure to an Australian gravity concentrate. This was attributed to the native gold particles in the concentrate being either too large, agglomerated in slimes or coated with minerals. Although this particular application was unsuccessful, this water-CO2 biphase technique may be applicable for other separations that require the removal of very fine, hydrophobic particles from an aqueous slurry.

Jan 1, 2000

By P Cavieres, R Dunlop, S Gaete

El Teniente Mine started the exploitation of the primary rock in the beginning of the 1980s decade, using caving methods. Since the beginning the mining activities have induced seismicity including some occasional rockbursts. Owing to the relevant damages, the mining operations were stopped in some production sectors. This paper describes the concepts that have been used in order to control the induced seismicity based on the strategies for controlling the rockmass breaking process, which depend on mining parameters. It also presents the main concepts applied in the Teniente Sub6 sector design and the experience collected during its sector exploitation.

Jan 1, 2000

By P. Meyers, F. DeSilva, L. Gottlieb

A number of tests looking at lead removal using ion exchange resins of various types from various aqueous streams have been undertaken. The tests focused on strong acid cation (SAC) and weak acid cation 0N AC) resins. It was found that the mechanism of lead removal is partly by lead filtration rather than solely by ion exchange in a large portion of the applications studied. This is not surprising since lead carbonate is essentially insoluble and almost all water supplies contain at least some carbonate alkalinity. Regeneration of lead from exhausted resins containing significant amounts of lead may not be practical in some cases because of the large chemical and waste volumes involved. Since lead, .·along with many other very insoluble metals, is often present as a suspended solid rather than in ionic form, ion exchange is probably not always the best technology for bulk lead removal.

Jan 1, 2000

By T. L. Owen

Since 1993 Cyprus Amax has brought $2.5 billion dollars of greenfield and expansion projects into production, taking it from a mid-sized domestic minerals company into a major international minerals organization. The near simultaneous development of these multiple mineral projects in different locations around the world provided the opportunity for Cyprus Amax to develop a formal project management approach based, in large part, on an outsourcing philosophy. This formal project management system along with its outsourcing philosophy has served the growth agenda of Cyprus Amax extremely well. These preceding factors, coupled with the in-house retention of a core project group that fully understands the breadth of skills and abilities needed to undertake development of multiple large projects successfully, have been the cornerstone of Cyprus Amax’s project development success.

Jan 1, 2000

By Paul Schmiesing, Matt Higgins

Central Oregon is a fast growing resort community centered in Bend, Oregon. Bend is bordered by the Cascade Mountains to the west and the high dessert to the east. Central Oregon is blanketed with lava rock with little topsoil. Ditch blasting is a staple in the area. Almost all utilities excavation (gas lines, sewer lines, water lines, and electrical lines) requires blasting. There is also a considerable amount of blasting required for site excavations and drywells. On average, there are over 500 blasts per year in Bend alone. All of this blasting is done using small holes, generally 2.5 inches in diameter. Typical ditches will have 200 holes, between 2-3 rows wide, with an average depth of 8 feet, and on 36 inch centers. Almost all shots are dry. Successful blasting requires careful control of drilling and loading. The vesicular basalt contains numerous lava tubes and caves making drilling and loading difficult. The rock conditions vary greatly from one side of town to the other requiring different powder factors and different scale of distances for vibration control. Caret%1 calculations of vibration predictions and use of site-specific seismic info is necessary. Marry shots will require deck loading and careful timing to ensure one-charge per delay. It is an every day occurrence to be blasting near residential and commercial structures or high pressure gas lines. Many times ditch blasting will incorporate excavation blasting. The different hole patterns used for the ditches and the excavation shots presents challenging timing sequences.

Jan 1, 2000

By S M. Denn

The Cawse nickel-cobalt operation is situated 50 km NW of Kalgoorlie in Western Australia, at latitude30o22'30'' south and longitude 121o08'30'' east on the Kalgoorlie 1:250 000 geological map sheet (SH 51-9) (see Figure 1). The project is owned and operated by Centaur Nickel Pty Ltd (CTR) and was the first in Australia to commercially produce nickel metal and cobalt sulphide through pressure acid leach (PAL) technology. Cawse has a total resource base (all categories of resources + reserves) of 213 million tonnes Mt at 0.7 per cent Ni and 0.04 per cent Co, comprising 127 Mt at Cawse Central which is 100 per cent owned by CTR and 86 Mt at Cawse Extended where CTR has a 80 per cent equity. Cawse Extended is located immediately to the northwest of the Cawse Central leases. All current reserves (proved and probable) of 30 Mt at 1.0 per cent nickel are contained within Cawse Central. In addition the Siberia project area 20 kilometres to the NW has a resource of 63 Mt at 0.7 per cent Ni. Cawse is a dry laterite deposit, with nickel and cobalt hosted by iron and manganese oxides. Cawse Central mineralisation extends over a ten kilometre strike length, with three pits currently being mined. The Bunyip pit has the premier nickel and cobalt grades within Cawse Central. There are seven dominant lithology types forming mappable units within current pit exposures. Four of these units are host to nickel and cobalt mineralisation. Ore types are defined as Upgrade, Grind and Non-upgrade, depending on their physical characteristics with respect to the treatment route. Mining commenced in February 1998. To the end of calender 1999 the operation has produced 2100 tonnes nickel plate and 470 tonnes of cobalt as a cobalt sulphide product. Future production will target 9000 tonnes per annum Ni metal and up to 2000 tonnes per annum Co, based on processing 500 000 tonnes of ore per annum.

Jan 1, 2000

By G. R. Dunning, M. R. Wilson

"Abstract - The early Paleozoic accretionary tectonic regime that was established along the Laurentian margin of the Newfoundland Appalachians provided a favorable setting for shear-hosted gold mineralization along a major terrane suture, the Baie Verte-Brompton Line. The Stog’er Tight prospect is one of several mesothermal-style gold occurrences hosted by shear zones within accreted ophiolites and oceanic arc terranes on the Baie Verte Peninsula. It is an epigenetic, stratabound deposit that is confined to shallow-level gabbro sills within the volcanic cover sequence of the allochthonous Point Rousse ophiolite complex. Gold mineralization at Stog’er Tight is associated with hydrothermal mineral assemblages represented by chlorite-calcite, sericite-ankerite, red albitepyrite (±Au) and chlorite-magnetite alteration zones. Gold occurs with pyrite within the intensely altered gabbro, along the margins of syn- to late-shear, quartz-rich, replacement veins.The Stog’er Tight gabbro served as a rigid body conducive to shear deformation and fluid penetration, whereas, its high Fe-Ti oxide content induced fluid oxidation and gold-pyrite precipitation. Hydrothermal alteration involved progressive CO2, S, Na, and LILE metasomatism, along with significant enrichments in the REE, HFSE, and Th in the high-grade ore zone. Temperatures of vein formation and alteration are constrained by oxygen isotope thermometry to be between 250°C and 480°C. Isotopic compositions of vein quartz from the Stog’er Tight prospect are uniform (??O = +12.5 ± 1‰) and fall within the range cited for many shear-hosted, auriferous quartz veins.A U-Pb zircon igneous age of 483 +3/-2 Ma for the Stog’er Tight gabbro is consistent with its stratigraphic correlation with other Ordovician ophiolitic and volcanic arc/back-arc assemblages in Newfoundland. The U-Pb age of a rare variety of hydrothermal zircon recovered from the high-grade ore zone directly constrains the timing of gold mineralization to 420 ±5 Ma, in accord with a major orogenic episode of Silurian age that produced many of the magmatic and metamorphic rock suites in north-central Newfoundland. Our results are consistent with a post-peak metamorphic, late-magmatic model for gold mineralization that occurred during the waning stages of Silurian orogenesis, driven by emplacement of I-type granitoid intrusions into the crust."

Jan 1, 2000

By Michael Olmsted

Inspection of boreholes prior to blasting can result in cost reductions as well as increases in efficiency and safety. Until recently, borehole inspection was performed in two manners. For simple inspections, a flashlight was used to view the upper part of the hole. More thorough inspections were performed with long tool strings developed for oil field applications. Borehole inspection tools developed specifically for mining and blasting applications have now been developed. Video Cameras developed for borehole inspection have been in service for several years. Now measurement tools are available, developed specifically for mining.

Jan 1, 2000

By Monica Pavlik, Thomas Wildeman

Water from the Forest Queen mine adit near Silverton, Colorado drains into a natural wetland. Because the pH of the water averages 5 and the iron concentration averages 18 mg/L, it was thought that the wetland might naturally treat the water. Of most concern with respect to the aquatic environment is zinc whose concentration averages 0.60 mg/L. Starting in October 1997, the surface waters, ground waters in the peat substrate, and the sediments in the wetland were sampled and analyzed four times over the course of four months. The adit water primarily remains as surface water where Fe, minor amounts of Al, and no Zn are removed. After the adit water enters the peat, then it is found that the pH rises to 5.8-6.5 and sulfate is reduced. The removal of Zn and A1 is caused by these two changes. However, Fe in its reduced state is quite soluble and may be remobilized in the reduced environment of the peat.

Jan 1, 2000

By R. Stenne

This paper deals with a complementary soil investigation which being part of the contract helped understand the behavior of a softened clay and adjusted the design of a retaining structure accordingly. The investigated softened clay proved to have lost its original strength but had maintained some characteristics of its stress history and in particular high horizontal stress. Pressuremeter tests and flat dilatometer tests were of interest to estimate the at rest earth pressure. A design consisting of a T-shaped slurry wall in conjunction with transverse walls was the most effective solution to cope with high active pressures and low passive pressures.

Jan 1, 2000

By Jayagopal Ucbil, M. Krishna, V. T. Vijayalakshmi

"The pitting susceptibility of aluminium metal matrix composites reinforced with garnet particles has been examined using static weight loss method by exposing the metal matrix composites (MMC) specimens to the action of IN HCI acid at laboratory temperature for different time intervals. It was found that the corrosion rate decreased with increase in weight percentage of reinforcement while the corrosion rate was a function of the matrix alloy but not of the reinforcement material. Further, it was found that the rate of corrosion was dependent on the interface region formed between the reinforcement and the matrix. A comparison of the base matrix with the corresponding composite when subjected to heat treatment for varying periods of 4, 8, and 12 hours respectively was made. The comparison revealed that corrosion resistance of the composite increased with the duration of heat treatment and this has established a considerable improvement in corrosion resistance of the composite when compared with the base matrix.IntroductionMetal matrix composites (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and light weight [1-5]. The trend is towards safe usage of the MMC parts in the automobile engine, which work particularly at high temperature and pressure environments [6-7]. Particles reinforced MMCs have been most popular over the last two decades. Among the MMCs, the most popular families are represented by aluminium reinforced with ceramic particles. Although the incorporation of the second phase into a matrix material can enhance the physical and mechanical properties of the base metal, it could also significantly change the corrosion behavior."

Jan 1, 2000

By Hideo Nakae, Hideki Yamaura, Toshiaki Kimura

"In 1968 J. N. Reding et al. suggested processes for fabricating composites. According to their patent, decompression atmosphere, which occurs during the reaction between magnesium and oxygen and/or nitrogen in the closed system, causes the spontaneous infiltration of melt into narrow spaces such as ceramic preforms. However, they did not report the proof of this phenomenon or the industrial manufacturing method. Therefore, this research measured the pressure change among SiC particles surrounding molten aluminum. As a result, the pressure reduction during the Mg reaction was identified. Moreover, the existence of Mg3N2, which improves the wettability between Al alloy melt and SiC particles on the interface, was observed on the surface of particles. Applying these two phenomena, a new process for the manufacturing of cast discontinuously reinforced aluminum composites (DRA) was developed. This new method is expected to produce DRA without additional pressure.IntroductionWith the increasing demands for light-weight materials in the automotive and aerospace industry in recent years, ceramic particulate reinforced aluminum matrix composites called DRA (Discontinuously Reinforced Aluminum Composite) have been receiving significant attention because of its lightness, superior abrasion resistance, high heat conductivity and low thermal expansion [1-3]. Consequently, DRA was considered for electronic parts such as heat-sinks or a base for power semiconductors, and began to be applied for automotive parts including brake drums, discs, cylinder liners, pistons and so on [4- 6]. However, high machining cost is one of the significant barriers to widespread use ofDRA. One solution to this problem is the adoption of cast DRA that can be produce to near-net shape, reducing machining cost."

Jan 1, 2000

By Yasuhiko Ito

"This talk is concentrated on the topics of compound film formation on the substrate electrode by interdiffusion of substrate element and electrochemically deposited species and/or by direct electrochemical implantation of the component element of the film into the substrate. As a typical example, electrochemical implantation of nitrogen atom into Ti metal to form TiN surface film is described. Another example is the formation of various kinds of intermetallic compound films including Ni2Y, Ni2Dy and Pd3 Y by the electrochemical implantation of lanthanoid elements into transition metal electrodes. By combining these two methods, Sm-Fe-N ternary material film also could be formed. The principle and application of the ""electrochemical implantation"" are discussed in detail.IntroductionGenerally speaking, surface film formation by molten salt electrochemical process can be divided into the following three categories:(i) single element film formation on the electrode by electrodeposition,(ii) compound film formation on the electrode by electrocodepostion of more than two elements, and(iii) compound film formation on the substrate electrode by interdiffusion of substrate element and electrochemically deposited species and/or by direct electrochemical implantation of the component element of the film into the substrate.This talk is .concentrated on the topics of category (iii), especially on the electrochemical implantation. Typical example can be seen in the electrochemical implantation of nitrogen atom into Ti metal to form TiN surface film. Another example is the formation of various kinds of intermetallic compound films including Ni2 Y, Ni2Dy and Pd3 Y by the electrochemical implantation of lanthanoid elements into transition metal electrodes. By combining these two methods, Sm-Fe-N ternary material film also could be formed. The principle and application of the ""electrochemical implantation"" are discussed in detail with examples above as well as other experimental results also obtained very recently in the author's laboratory."

Jan 1, 2000