Search Documents

By Judson G. Brown

In the May, 1969 issue of Mining Engineering the Editorial Director, John V. Beall, described the Japanese Onahama Copper Smelter and Refinery as follows: "On the shore of the Pacific, 120 miles north of Tokyo, is the world's most modern copper smelter and refinery.? One of the improvements that has been made at the Onahama Refinery is the quality of the electrolyte in the copper refinery electrolytic cells. This has been accomplished by reducing the concentration of slimes in the cells between the electrodes. In a December 19, 1966 review in Chemical Engineering magazine reference was made to some tests in Sweden as follows: ?However, at 1,000 amps/sq.M., satisfactory cathodes could be prepared, provided electrolyte flow past the anode and cathode was at least 3 to 4 meters per minute, and the slime content was not allowed to exceed 20 to 30 mg. per liter. By dropping the current to 500 amps with the same electrolyte velocity, the slime content could grow to 50 mg. per liter (50 ppm) without causing occlusion at the cathode." From this data it appears that the production capacity of copper refining electrolytic cells can be significantly increased. In order to do this the concentration of suspended contaminating slimes in the electrolyte solution is reduced by filtration. The electrolyte in-between the active electrodes must be purged with higher velocities to maintain a high concentration of the desirable copper ion in the liquid film adjacent to the cathode and the sulfate ion in the liquid film at the anode. This higher velocity also carries away from the cathode the undesirable impurities released from the anode as they are released into the electrolyte as filterable solids.

Jan 1, 1970

By G. C. Kachel

Significant effort has been expended and considerable success has been realized m the application of instrumentation and automatic control equipment in the mining and ore processing industries. This effort has been applied principally to process equipment with the objective of increasing throughput, minimizing labor requirements and/or improving grade or product quality. Less spectacular, but quite rewarding has been the successful application of instrumentation and automatic control equipment to a wide variety of material handling equipments. This paper describes some of this work including: (1) automatic weighment of load-haul-dump units and trams underground; (2) automation of skip loading; (3) instrumentation applied in feeders and conveyors; (4) level measurement in bins, silos, vessels and sumps; (5) automatic blending of sized materials; (6) automatic loading of ships, trains and trucks; (7) automatic control of tailings disposal facilities

Jan 1, 1973

By Tim Arnold

"Justified is a show on FX that takes place in Kentucky coal country. The two main characters, a cop named Raylan and a criminal named Boyd, are adversarial to the very end, yet they manage to maintain a seemingly inexplicable bond of friendship through it all. The final episode ends (spoiler alert) with Boyd asking Raylan why that is. He responds, “If I allow myself to be sentimental, there is one thing I wander back to” Boyd responds, “We dug coal together.” Fade to black.What creates these types of bonds between friends and co-workers in mining? I don’t know about you, but many of my best friends I met in mining. Certainly the people I respect the most in this world are a part of our industry. Good, honest, honorable men and women. And I am not just talking about the leaders of our industry. I am talking about great miners who taught me how to do the right thing and also be productive.I have had the pleasure to work for some great people and the misfortune of working for some of the loudest screamers. What I consider the worst butt-chewing in my life may surprise you. I once worked for a man I respected, because he showed me respect. He went on a business trip and left some instructions. For some reason, I was able to justify to myself that they applied to everybody but me, and I disobeyed them. When he returned he called me into his office and said to me: “Tim, you pissed me off when you did that.” He said it quietly and with no anger. I had lost his respect. This devastated me more than any screaming shift boss ever could have. I learned a lot about values from that conversation.Most of us will spend more time at work than we will with our families over a lifetime. It is natural that tight bonds be created at work. What I believe makes mining special is that these bonds are so strong. They are strengthened by the incredibly hard work our miners do. They work at all hours, on holidays and in all sorts of extreme weather conditions. The physical demands of the job are sometimes exhausting. Our bonds are further reinforced because the work is dangerous. Not only does management watch out for the wellbeing of their people, but each and every one of us looks out for one another. The bonds are made tight because our people are so passionate about what they do, no matter the department or profession. Finally, they are strong because of the thousands in the industry that keep doing the right thing, every day. We make great friends in this industry because of the strength of character of our people. That is why Boyd and Raylan respected one another so much."

Sep 1, 2016

By Jürg Künzle

The use of the underground space has been a recurring issue in human history, whereas the reasons for building subsurface structures have changed over time. In the decades to come, the world will be marked by a variety of underground projects never before seen. This paper describes a series of characteristic challenges of designing and building underground freight transportation systems, with reference to the example of Cargo sous terrain, a privately funded underground logistics project in Switzerland. It provides an overview of contracting practices that allow these challenges to be addressed with success.

Jun 13, 2021

By Evan Brinkerhoff, Steve Chorley

The largest hard rock TBM ever to bore in the USA, an 11.6 m diameter Robbins Main Beam TBM, recently underwent a planned in-tunnel diameter change to a more compact 9.9 meters. The first-of-itskind conversion process for the Main Beam TBM was undertaken 2.8 km into the bore and was not done inside a shaft or pre-excavated portal. This paper will detail the unique dual-diameter machine designed for the Mill Creek Drainage Relief Tunnel in Dallas, Texas, USA, machine performance, and successful size conversion process that took place in early 2021—a process that utilized the four C’s of construction to enormous benefit: Communication, Cooperation, Collaboration and Coordination.

Dec 1, 2022

By R. Aliberti, E. Comis, M. Wone

DC Water’s Clean Rivers (DCCR) program involves the construction of approximately 29 km (18 mi) of CSO tunnels in Potomac Group soils in the Washington DC area. Soils include an upper predominantly over-consolidated fine grained plastic material facies (P/A) and lower predominantly coarsegrained facies (PTX). As earth pressure balance (EPB) tunnel boring machines (TBMs) are mainly used in such soils, the correct approach to soil conditioning can make a considerable difference in TBM performance. Soil conditioning laboratory tests are often completed during the planning phase prior to TBM excavation to develop a baseline for soil conditioning, reduce risks, minimize costs, and improve performance. However, only a few basic tests are standardized to date, and conditioning regimes are fine-tuned during the mining phase. The paper illustrates the effort carried out to identify the correct soil conditioning regime for both PA and PTX facies to improve TBM overall performance and reduce ground movement during the excavation of the Northeast Boundary Tunnel (NEBT) in Washington DC.

Dec 1, 2022

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and MPSI merged, a unique opportunity occurred for two independent mill fabricators to compare various design procedures and the research upon which they were based. This paper documents such a comparison in the structural design area. Several SAG mill analyses are compared using both Boliden Allis and MPSI methods. The differences and similarities are then utilized in a correlation of critical stress definitions and the acceptable design and inspection criteria.

Jan 1, 1992

By Ali Kazmi, Wern-ping N. Chen

A load rating procedure was performed to evaluate safe load capacity of the Port of Miami Tunnel (POMT), FDOT Tunnel No. 871071 SR 887. The rating procedure performed on a total of eleven stations beneath roadways and with fill depth less than the tunnel exterior diameter (42 ft). Calculations on tunnel sections passing beneath roadways were performed to evaluate the structural response of the sections subject to moving vehicular loads, dead load, and earth pressures. Ratings were performed in accordance with AASHTO and FDOT guidelines. The procedure considered two types of vehicles (HL-93 and FL-120) and two rating levels (Design level and Permit level). As part of HL-93 vehicle, Tandem load was also considered for rating, separately. For HL-93 and HL-93 Tandem, inventory and operating level ratings were performed. The results show rating factors are high. The minimum rating factor is 16.8 using Inventory truck HL-93. For Permit level using FDOT FL-120 truck the minimum rating factor is 6.9. As can be seen, rating factors are higher than comparable analysis for bridges. This paper explains how the procedure can be implemented for tunnels and evaluates the rating results.

Dec 1, 2022

By Ryan P. Sullivan, Ben D. DiFiore, Robert J. Auber, Michael A. Piepenburg, Lisa M. Smiley

Pollution to Lake Erie will be significantly reduced by the Westerly Storage Tunnel (WST) system, which is mainly comprised of a 10,000-ft long tunnel and a dewatering pump station in the downstream tunnel shaft. Separate construction contracts for the tunnel and pump station required careful management of the interface risks. A key decision was to decouple the projects by relocating the mining shaft away from the pump station. The need to receive the tunnel boring machine (TBM) in the pump station shaft was eliminated by dismantling the 28-ft diameter TBM in the tunnel then carrying it back through the tunnel and up the mining shaft. This paper discusses how interface risks were successfully managed during design and construction to limit overall schedule impacts.

Dec 1, 2022

By J. F. Barry

Newmont Mining Corporation and Barrick Goldstrike Mines, Inc. concluded an exchange of land and reserves in an agreement signed May 3, 1999.This exchange of assets allowed Newmont to develop the Deep Post underground mine from within Barrick’s Betze-Post open pit, thus reducing capital expenditures, lowering operating costs, and advancing the production schedule by nearly three years. Based on previous experience, Newmont is confident that the Deep Post underground mine can be successfully developed and operated within a large, active, open pit mine. The project also faces difficult geotechnical conditions including weak ground, scattered pockets of groundwater, and elevated rock temperatures.

Jan 1, 2000

By Andrew J. Neale, Chelvan Veloo

P.T. Freeport Indonesia currently operate a 600,000 t/d mining and 125,000 t/d milling operation in the remote highlands of Irian Jaya, Indonesia. The isolated location and generally difficult working conditions make for challenges not encountered in most North American operations. In spite of this, the mill technical groups have been able to develop and maintain a highly effective level of plant wide automation. This has been achieved through the appropriate selection of available technologies and the implementation of innovative management practices. This paper provides an overview of the control systems currently installed and focuses on those practices which have resulted in the long term success of process control at Freeport.

Jan 1, 1997

By Sean Masse

New Gold?s New Afton Mine, located 8 km (5 miles) west of Kamloops, British Columbia, is a 4.5-Mt/a (5-million stpy) block cave mine, making it the highest tonnage underground hard rock mine in Canada. The reserve is estimated at 52.5 Mt (55.9 million st) with grades of 0.65 g/t (0.02 oz/st) gold and 0.93 percent copper (2012). Commercial production was achieved in July 2012 and nameplate production was achieved ahead of schedule in September 2012, with the cave breaching to surface in 2013. The mill has a SAG and a ball mill with a froth flotation circuit.

Jan 1, 2014

By James J. Gusek

The Atlantic City iron mine is located in Fremont County in central Wyoming, near the historic gold mining camps of Atlantic City and South Pass City. The mine lies on the southeast flank of the Wind River Mountains at an elevation of about 2,470 m (8,100 ft) above sea level (Fig. 1). An 81-h M2 (200-acre) tailings impoundment at the Atlantic City taconite operation has been a source of blowing dust. The site qualified for reclamation under Wyoming&apos;s Abandoned Mine Land (AML) reclamation program. The ultimate reclamation construction incorporated commercially available organic amendments and fertilizers into a 300-mm- (12-in.-) thick cap of a sterile clay loam cover material. The water level was lowered in an adjacent flooded mine pit that was feeding uncontrolled seeps into the tailings basin. A wide tailings pond spillway was built that allows flood control while minimizing seasonal water-level fluctuations in the pond. Rock berms and rock snow fences were built for wind-erosion control and soil-moisture preservation. Future work includes tree planting in the protective wind/ snow shadows of rock berms and rock snow fences and plugging a decant pipe. US Steel opened the Atlantic City iron mine in August 1962. It closed in 1983. Taconite iron ore was mined by surface methods. The ore was magnetically separated from the waste. The magnetic concentrate was mixed with bentonite, formed into pellets and roasted to produce a blast furnace feed stock for US Steel&apos;s blast furnaces in Geneva, UT. The pellets were hauled by rail to the Geneva Iron Works. The Atlantic City Mine produced three types of wastes. These included waste rock overburden from mining, a coarse-grained (sand to small-gravel sized), nonmagnetic reject rock termed "cobbs" and fine-grained tailings ranging from 600 to 75 µm (28 to <200 mesh). The waste rock has been used as an aggregate/rip rap source by a local contractor and the Wyoming Department of Transportation (WYDOT). WYDOT also

Jan 1, 1998

By Georgene Renner

With more than 800 booth spaces sold and 540 exhibiting companies displaying their wares, there was something for everyone on the exhibit floor of the 2014 SME Annual Meeting in Salt Lake City, UT Feb. 23-26. The following is a sample of what was offered at the 2014 meeting.

By Marcos de Paiva Bueno, Leonardo Ribeiro Lara, Rajiv Chandramohan, Thiago de Almeida, Greg Lane

This paper explores the impact of the significant difference between the number of geochemical assays conducted for grade estimation and the number of comminution tests performed for throughput and performance forecasting. Both grade and throughput are key factors in determining the project. We analysed 154 feasibility study reports to assess the impact of sample frequency for comminution test work on project revenue. This disparity in size between assay and comminution data arises because geological and resource-grade risks cannot be managed without extensive geochemical testing, whereas comminution risks are traditionally mitigated through design methods and the use of contingencies. This approach is partly due to the relatively high cost and large sample requirements associated with traditional comminution tests. Our analysis demonstrates that insufficient comminution sampling and testing leads to uncertainties in throughput forecasts, creating significant financial risks. Data from the feasibility studies show that a 1% change in mill throughput can result in up to a 5% variation in Net Present Value (NPV), underscoring the sensitivity of project economics to operational performance. Building on previous work, we reference studies that reveal how low frequency of comminution testing can increase uncertainty in mill throughput forecasts and increase financial risks. We propose an approach that optimises the number of comminution samples tested to enhance forecast accuracy and reduce NPV variance. By adopting this approach, mining projects can improve financial reliability and mitigate risks associated with underperformance in SAG and AG mill-based operations.

Feb 1, 2025

By Erwan Yap, Brian Mangogna, Craig Romrell, Jeff McKay, Weishi Mang, Andrea Deml, Adam Steimel, Justin Dix

The Doe Run Company (Doe Run), a global supplier of lead (Pb), copper (Cu) and zinc (Zn) concentrates, and lead metal alloys, installed an enterprise expert control system— termed as Digital One—on the company’s Pb, Cu and Zn circuits at its Buick Mill in December 2022. Digital One was developed with Metso and deploys Metso’s product, VisioFroth™. This automated system is now running and optimizing the flotation processes for all three circuits (Pb, Zn and Cu), all plant air and methyl isobutyl carbinol (MIBC). In addition, Digital One also controls a second, newly built, modern flotation reagent system. Digital One also paves the way for automation and expert control of the entire mill, integrating grinding, thickening and filtration. Digital One is digitally immersed in a universal distributed control system (DCS); therefore, today’s mineral processing plants may be upgraded to it or designed around it. This presentation will explore the plant design and operation of this technology at the Doe Run Buick Mill.

Feb 1, 2024

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By A. Bhargava, V. Nasri

Traditionally, secant piles have been utilized to provide temporary support during excavation for shafts and cut-and-cover tunnels. As an alternative, the secant piles can be included into the permanent structure, where they serve as the envelope sustaining the lateral loads and gravity of the permanent structure in addition to supporting the excavation during construction. This has several benets, such as shorter building times and lower excavation costs. Recent construction of an approach structure and an underground station as part of Montréal, Canada’s Réseau Express Métropolitain (REM), one of the biggest transit systems in North America, was completed with remarkable success using this. In this paper, a case study based on a project that employed secant piles as the permanent liner is presented. Techniques to guarantee a watertight construction with over a century of service life are described, along with a variety of structural and waterproong methods applied to create an economical design.

Jun 23, 2024

By John Kuyt, Zili Li, Michael Mooney, Michele Mangione

"INTRODUCTIONTwin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world. A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a betterunderstanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This paper discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link Project OverviewThe Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with over 7km of twin-bore road tunnels, two lanes each, with several caverns, interchanges, and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a Public-Private Partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5m double-shield Herrenknecht TBMs [1]. The TBMs were used in EPB-type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1 m diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in a 9 segments + 1 key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis [2]. Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Jan 1, 2016

By Erik Marsh, Frederick C. Harris Jr., Javad Sattarvand, Joshua Dahl, Alireza Kamran Pishhesari

Based on the mine safety and health administration (MSHA)reports, mining truck accidents are among the significant causes of fatalities in the mining industry. The major causes of haulage accidents can be divided into non-driving and driving factors, such as truck-related sudden failures and operator performance. Numerous parameters affect trucks' safe operation, but situational awareness plays a significant role. Due to the distinct structure of mining trucks, making them efficient for mining purposes, the operator has a very limited field of view (FOV), making them prone to accidents resulting in losing lives. The cabin's position blocks the truck's right and rear sides, creating several blind points around it. Aiming to test/train the operator's awareness of the surrounding, a proximity detection system is developed through a multiplayer virtual reality (VR) application to investigate the human factor in equipment collisions. The operators were examined and monitored when asked to conduct what exactly happened in the Marigold mine truck accident without being aware of the scenario. After receiving sound, vibration, and visual alarm warnings, their reaction and performance were analyzed. The platform is developed using the Unity game engine for HTC VIVE virtual reality goggles. An Omni-direction treadmill and a motion simulator platform are utilized for the player and dump truck operators. Fifteen students were monitored when driving the dump truck receiving/not receiving proximity detection alarms. None of them repeated the accident when receiving proximity alarms. Also, they found the visual alarm the most comfortable while driving the truck.

Jun 25, 2023