Search Documents

By David E. Albus, Bidjan Ghahreman

A single-family home constructed on the side of a slope in Los Angeles, CA, was subjected to lateral forces due to soil slope creep on the pile foundation supporting the home. Impacts to the property included cracking and separations in the street, retaining walls, exterior concrete flatwork, and decorative concrete features in the rear yard area. The home was supported by concrete piles that penetrated the surficial soil mantle and were embedded in underlying bedrock. However, the home exhibited minor distress that suggested even the home was being affected by soil creep. Selected points on the home were monitored with an optical survey method and manometer over a period of two years to assess if the home was undergoing vertical or lateral movement. Monitoring data indicated the home was in fact moving down slope in a manner consistent with slope creep. As a result, the authors were concerned that continued movement due to slope creep could result in over-stressing of the piles that support the home and ultimately lead to failure of the foundation system. An evaluation was then undertaken to evaluate the behavior of the foundation system due to forces from slope creep. Research was performed during the course of evaluating the conditions to consider various approaches to modeling pile behavior of the piles supporting the home. Some research has been performed to field measure creep displacement of soils and rock in slopes. These previous works have found a diverse behavior of the soil displacement with depth (velocity profile) indicating the process is very complex. An example of various velocity profiles measured in field experiments is depicted in Figure 1. Other research focused on theoretical models of velocity profiles and exhibited similarities to some of the field measured cases.

Jan 1, 2018

By Radianto Elprama

For the realisation of the underground railway line RandstadRail in the city area of Rotterdam a bored tunnel is under construction. Diaphragm walls up to a depth of about 40 m were used to construct the building pits for the start shaft, the Blijdorp Station and the end shaft. The water tightness of the diaphragm walls was determined by leakage tests that were executed after the construction of the walls, but prior to the excavation of the building pits. The tests showed satisfactory results with a hydraulic resistance of the diaphragm walls of at least 500 days. To determine the water tightness of diaphragm walls it is recommended to follow the specific procedure as described in this paper.

Jan 1, 2006

By Q. M. Huang

In 1979 our company undertook the project of infra-structural work of White Swan Lake Hotel, (International class ) Guangzhou. Visit to the site showed that it was situated at the riverside, covering an area of 54,000 M2 with 30,000 M2 of which reclaimed from Pearl River. The material used for reclamation was black sand which was dredged from the nearby riverbed. The sand had the properties of high permeability and very low internal friction. The basement of the building was 6.2 m below ground level and 3 m lower than the riverbed. Apart from the pile foundation, a diaphragm wall was to be constructed prior to the commencement of excavation work for basement. A feasibility study was carried out to determine the method of construction which would maximize utilization of the plants and equipment that were available in the execution of the aforesaid foundation works. This report concerns only the construction of the diaphragm wall and the performance of the plants employed. A detailed delineation of the construction method is herein discussed

Jan 1, 2010

By M. Tominaga

An industrial port complex was constructed on the west coast of Leyte Island The work was started in December 1981 and completed in May 1984. This port complex includes a 665 m long wharf and can accommodate vessels ranging from a 60,000 DWT ore carrier to a 4 000 DWT general cargo ship. It now handles materials for and products from a copper smelter with an annual capacity of 130,000 t and a fertilizer plant with an annual capacity of 900,000 t. The Wharf structures consist mainly of interlocked steel pipe piles, steel sheet piles and steel pipe Piles. Material handling equipment such as unloaders, shiploaders, etc. were installed on the wharf. Site survey, planning, engineering design and construction aspects of the port development are discussed in this paper with particular emphasis on the wharf structure.

Jan 1, 2010

By Ramdane Bahar

"Abstract The design foundations can be performed using Menard pressuremeter rules that require a limit pressure and a pressuremeter modulus. In recent years, another trend of interpretation of this test is appeared. It consists of identifying the rheological soil parameters using analytical or numerical methods and then used to evaluate the bearing capacity and settlement of soil foundations using numerical software. This paper deals with the bearing capacity and settlement predictions of bored piles using two approaches. The first one is the method called ""Pressident"" which is a numerical program developed to analyse pressuremeter tests taking into account the Duncan and Chang model. The second approach is the method developed by Bahar and Olivari based on the generalised elastoplastic Prager’s model with the Von Mises criterion which is suitable to describe the behaviour of saturated clays under undrained conditions. The pressuremeter data, collected on various research and consulting projects are used to explore the relationship between limit pressure and undrained shear strength obtained by the two methods. Numerical calculations, by FLAC2D software taking into account the rheological parameters derived from these two methods, are performed in order to predict the behaviour of a single bored pile subjected to an axial vertical load. The predictions are comparedto the measured data.IntroductionThe Menard Pressuremeter test has been used extensively to measure in situ soil properties and for the design deep foundations in Algeria. These tests are an useful and economical way for obtaining reliable in situ properties of soils and provide the measurement of in situ stress-strain response of soils. From this test, the design foundations can be performed using pressuremeter rules that require a limit pressure, pl, and a pressuremeter modulus, EM. These two parameters are derived from the pressuremeter curve or deduced from existing correlations with undrained cohesion and internal angle friction (Ménard, 1957; Amar and Jézéquel, 1972), and are used to evaluate the bearing capacity of soil foundations and the expected settlements. But, they can also help to identify usual soil parameters required by simple constitutive models for soils in numerical calculations."

Jan 1, 2014

By Issa S. Oweis

Limestone is a sedimentary rock composed primarily of calcite (calcium carbonate). In the presence of an aqueous solution of carbon dioxide (carbonic acid) bicarbonate radicals (2HCO3)- are produced that are highly soluble. The same type of reactions occur in terrains where dolomite (calcium magnesium bicarbonate) reacts with carbonic acid to produce highly soluble bicarbonates (4HCO3)-. The source of carbon dioxide is the small content in rainfall but to a large extent from the organics in the soil. The solution activity depends on many factors including the content of carbon in the rock, acidity of soil water, groundwater velocity and other factors. The resulting features are referred to in literature as sinkholes, solution channels, caves, karstic topography, and cavernous limestone. The presence of solution features affect the shafts in several ways: (a) the shaft resistance is affected by voids along the shaft, (b) concreting of the shaft should consider the presence of voids along the shaft, and (c) the shaft base may be in close proximity to a solution feature that may cause future collapse under structural loads. Methods to mitigate such effects include verification of rock to below the base (vertically and laterally). Cavities are stable by virtue of arching in the rock. Under the action of end bearing from a shaft, the arch may collapse depending on its proximity to the base of the shaft and the strength of the rock. This paper focuses on this issue. Finite Element analyses are conducted to relate shaft end load and bearing area that will produce failure based on given rock properties, size and location of cavity. Failure is defined as settlement of the base equivalent to 5% of shaft socket diameter. The software Plaxis is used for analysis. The rock is considered as c-f material derived based on Hoek-Brown failure criteria (2002 edition) that is based on Geological Strength Index (GSI).

Jan 1, 2009

By A. B. Desai

The construction of 1144 nos. of piles, each 1.5 m diameter, bored-cast-in-situ type and varying in depths from 6.5 to 23m, has been completed as foundation for 26 piers of 548 m long aqueduct across Orsang river to carry 1128 m3 water of Narmada Main Canal of the Sardar Sarovar Project in Gujarat. These piles are socketed 1.5 m into foundation grade rockmass. The portal system of 44 nos. of piles and pile cap at the top for each pier is analyzed considering the portal fixed at bottom of piles. The borings for pile shaft were done deploying reverse mud circulation rigs and also by conventional chiseling and bailing operations. Besides vertical loading tests and lateral loading test on piles, dynamic tests such as low strain integrity testing on 290 piles and high strain pile testing on 17 piles were also conducted. The results indicated that (a) the settlement/ displacement are much less than the prescribed limits (b) good quality of concrete (c) piles are firmly socketed and (d) piles have adequate structural capacity to withstand the design load.

Jan 1, 1996

By experience we know about the natural event of ocean-tides. In geophysics we say that the earth-tides phenomenon is the elastico-viscous response of the earth's body to the attraction potential of moon and sun. By the fact that the tides on the planet take place in a regular periodic frequency, due to the earth rotation of 24 houres for one cycle, the rotation of the moon in about 28 days around the earth and finally to the rotation of the earth-moon combination around the sun in 365 days this phenomenon is a very important one in geophysics. The exact calculation of the acting forces is possible and the comparison of the earth's body response to these forces as well.

Jan 1, 1987

By J. X. Wu

An investigation on the seismic damage to buildings with pile foundations in Tianjin region, was conducted after the earthquake which hit Tangshan in 1976. It showed that most pile-founded buildings have an excellent aseismic capacity. In this paper, several pile-founded projects suffering the seismic damage are introduced as examples, simplified calculations are made of the vertical bearing capacity of pile foundations and of the horizontal seismic force, and suggestions are presented in conection with the design of pile foundations in the liquified ground soil. The paper shows a frame structure which has a plie foundation with a box-shaped base. Analyses if its response to the earthquake has been carried out in accordance with the F.E.M. and results have been obtained.

Jan 1, 2010

By A. Mazzucato

This paper presents the experimental results of driving and load tests on an instrumented pile driven into a test pit filled with fine homogeneous sand.

Jan 1, 2010

By George Mylonakis

The curvatures and subsequent bending imposed to piles by the surrounding soil during the passage of strong seismic waves is studied. This type of bending develops even in the absence of a superstructure and is referred to as "kinematic bending", to distinguish it from bending imposed to piles by loads generated from the inertia of the superstructure ("inertial bending"). Although kinematic loading may be severe in the presence of sharp stiffness discontinuities in the profile and may lead to damage, it has received little attention by engineers. The scope of the paper is twofold: (i) to discuss some fundamental aspects of seismic pile bending, and (ii) to review some existing design methods. To this end, a dimensionless bending strain parameter (instead of the more commonly used bending moment), and a strain transmissibility function relating pile bending strain and corresponding soil shear strain are introduced. Numerical examples are also presented.

Jan 1, 2002

By B. N. Hira

A multistoreyed residential complex was at the penultimate stage of construction by ONGC at Nazira, Assam. The site was situated at high earthquake zone. The subsoil was very weak and contained soft to medium clay with water table almost at the ground level. The bearing capacity of soil was quite poor particularly with predicted settlement beyond permissible limit. In this situation, the conventional shallow and deep foundations were found uneconomical and ground improvement with granular piles was considered as the viable solution. ONGC approached the Central Building Research Institute with the request to design granular piles along with R.C.C. foundation and other suitable cost effective measures. CBRI collected relevant geotechnical informations and supplimented the data by conducting field tests at site and laboratory tests at Roorkee. Rational design of 30 cm dia. and 5.00 meter deep granular piles were suggested with isolated and combined RCC footings over the reinforced soil. In addition to several structural and geotechnical advantages, the granular pile foundation provided considerable economy in the cost of construction. The paper presents the salient geotechnical and structural informations of the challenging project and provides the design details of the innovative granular pile-system. It also furnishes the design approach of the RC footings and other elements of the foundation.

Jan 1, 1996

Abouleid,A.F.327 Ajdic, I.451 Albert, L.F. 221,307 Alem, A. 525 Asama, T. 431 Avgherinos, P. J. 373 Baker Jr, C.N. 331 Balossi Restelli, A. 171 Beckwith,G.H.33 Bellini, A. 469 Bermingham, P. 481 Bertero,M. 171,535 Beyer, M. 503 Bottiau, M.41 Botto, G. 205 Bruskeland, O. 337 Budhu, M. 349 Bullivant, R.A. 181 Bustamante, M.G. 185, 475, 535

Jan 1, 1994

By Tariq B. Hamid

Deep excavation is commonly associated with construction of different deep below-grade structural elements (e.g., basement walls and slabs, tunnels, retaining walls, tanks, utilities, etc.) Deep Excavation Retaining Systems (DERS) are required when open cuts with safe slopes are not possible. Careful analysis, design, and planning of the DERS are required to provide safe below-grade construction and secure nearby structures from damaging effects that may result from the deep excavation. Selection and design of temporary or permanent DERS (e.g., soldier pile and lagging, sheet piling walls, secant pile walls, tie backs, etc.) can have significant impact on time, cost, and performance. In order to design DERS using conventional methods, it is necessary to obtain shear strength parameters, angle of internal friction (ø), and cohesion (c), of retained soils. Residual shear strength parameters (ø'res, c'res) obtained from drained direct shear tests and triaxial tests on saturated samples have been commonly used in practice for the analysis and design of DERS. However, there are cases where ground water table remains at or below the base of excavation during the design lifetime of DERS. In such cases, the soil above the ground water table is in an unsaturated state. Therefore, it is important to account for the unsaturated conditions of soils in order to optimize the design of DERS. This paper is focused on implementing the basic concepts of unsaturated soils mechanics including matric suction and soils-water characteristic curve (SWCC) to estimate design shear strength parameters of unsaturated soils (i.e., ø°, c', and ø') for the design of a cantilever sheet pile walls, a typical case of study of the DERS. The results of this study indicate that the determination of unsaturated soil strength shear strength parameters is simple. In addition, using unsaturated soil mechanics theories has an outstanding impact on the design of retaining systems.

Jan 1, 2006

By Seung-hoon Lee

The use of piled raft foundations has been considered as an economical alternative to conventional piled foundations because a portion of the applied load is carried by the raft in the design of piled raft foundation. In analyzing the behavior of a piled raft foundation as a settlement reducer, an accurate estimate of settlements of the system should be made on the basis of the understanding of nonlinear behavior of piles in layered soils as well as the interaction between the raft, soils, and piles. Although the 3-dimensional finite element method and simplified analysis methods have been used for the design of piled raft foundations, these methods were found to be inadequate for the practical purpose or could not consider the interactions properly. This study developed an approximate hybrid method of analysis to be used for the practical design of piled raft foundations considering pile-soil, raft-soil, pile-soil-pile and raft-soil-pile interactions. In the presented method of analysis, the settlements of the system are estimated satisfying the compatibility of two separate models which are the flexible raft model consisting of 2-dimensional finite elements supported by springs representing soils and piles, and the group-pile model embedded in layers of soil having different properties. Comparisons with other analytical methods as well as a 3-dimensional FEM program were made to verify the sufficient capabilities of the proposed hybrid model for application to practical design and analysis of piled raft foundations.

Jan 1, 2008

By Roger Frank

"Abstract After noting the importance of standardization for piles, the European system is described (execution, tests and design, etc.). Some important aspects of Eurocode 7 are outlined (like the role of pile load tests). Finally, the calculation methods in the recent French standard for the design of piles following Eurocode 7 are shortly addressed.Importance of standardization for piles Like for other fields of geotechnical engineering, pile engineering is a complex art. For piles, the challenges are particularly numerous and many things must be mastered properly: - the soil investigation must be serious and adequate (for instance, deep enough!);- the choice of the pile type and the assumed behaviour must be assessed in order to reach a safe and economic design of the overall foundation;- the execution itself (construction and/or installation) deserves special attention and must follow strict state-of-the art rules.The geotechnical engineer, in charge of the design of a pile foundation, must have in mind the parameters linked to the variety of soils, of soil conditions and of pile types. A wide range of strong environmental issues are also to be considered: minimum disturbance during the execution processes, long-duration friendliness of the “inclusions” into the ground (to avoid pollution of the soils and waters, for instance) and respect of the neighbouring structures.Pile engineering plays in a world which is constantly moving and progressing: constructions expand in new difficult areas, actions on piles are more and more important, new execution techniques of piles are developed, research into the complex behaviour of pile foundations has no end, etc. Our views on how piles and group of piles really work are constantly evolving!"

Jan 1, 2014

By N. Shariatmadari

In recent years, determining bearing capacity of piles from in-situ testing data as a complement of static and dynamic analysis has been used by geotechnical engineers. In this paper, different approaches for estimating base bearing capacity of piles from SPT data has been compared and evaluated. A new method for pile base bearing capacity in sand is proposed using SPT records. Data averaging, failure zone extension, and plunging failure of piles have been addressed in the proposed approach. A data bank comprising 10 full scale static load tests on instrumented piles and 26 dynamic tests, analyzed with signal matching technique by CAPWAP software, was used for validation. The SPT data that was performed close to pile locations is also included in the data base. Comparison of current methods by error investigation with Log-Normal approach demonstrates that the proposed method predicts pile base capacity with more accuracy and less scatter in comparison to other methods.

Jan 1, 2006

By James M. Tantalla, Dwight Metcalf, Roderic A. Ellman Jr.

"The construction of a new low head hydro-electric plant at the Cannelton Lock and Dam required the design and construction of a cofferdam to accommodate a deep excavation extending approximately 150 feet below the Ohio River levels. The new plant, which generates about 390 GWh of electricity annually, is owned by American Municipal Power (AMP). A specialist team was assembled to design and construct the cofferdam, marine dike and CB slurry wall that helped make the project successful and on time for project delivery.Because the new plant diverts water from the locks and dam through a powerhouse to generate power, it would need to be partially in the river to operate properly. To accomplish this, approximately 250,000 square feet of land was reclaimed from the river by construction of a marine dike. The dike, combined with the design and construction of a 150 foot deep cement bentonite (CB) cutoff wall enabled construction of the new plant in the dry. Extensive dewatering analyses were performed using Modflow to evaluate pumping requirements and the number of wells needed to maintain ground water at required levels within the side slopes and final subgrade. A monitoring program consisting of inclinometers, piezometers and movement monitoring points were used to monitor cofferdam stability and performance throughout construction. Detailed two and three dimensional stability analyses that included a parametric study of fluctuating river levels and slurry unit weight were performed to ensure stability and suitable low permeability of the trench during cut-off wall excavation both on land and in the marine dike. The wall was constructed with both a hydromill excavating primary panels and a clamshell following behind to construct secondary panels. Data acquisition systems onboard the excavating equipment allowed for detailed confirmation of the continuity of the wall at each interface between panels. Another challenging aspect was the CB mix design for the trench. The cofferdam required the construction of a 1,300-foot long marine dike downstream of the existing dam up to 100 feet tall founded on existing river sediment to enclose the site and cut-off the seepage into the excavation from the river. Marine dike construction utilized vibro-compaction to pre-densify granular fills placed underwater through which the CB trench extended."

Jan 1, 2016

By S. L. Karunakaran

Selection of an appropriate foundation system requires great skill and ingenuity on the part of the designer. Certain guidelines for choosing between a pile and raft foundation are presented. A number of methods are available for estimating the capacity of piles, giving a wide range of values for the theoretical load carrying capacity. A few aspects to be taken into account while arriving at an appropriate theoretical capacity are discussed. The effect of fluctuation of water table level on the pile capacity and method of accounting for this factor on the pile capacity obtained through initial load test are also discussed. A case study presents a comparison between the estimated values of capacity of piles and the values obtained through the initial load test.

Jan 1, 1996

By Gary L. Seider

Helical screw piles are used in various applications including the underpinning of distressed foundations and as deep foundations for new structures. At present, maximum design loads range between 12.5 and 50 tons. Helical piles installed with in-situ grouting of the central steel shaft are a relatively new type of deep foundation, which have extended the present maximum design loads to the 100-ton range. Vickars & Clemence discussed this new foundation system in a paper presented at GEO-Denver 2000 in Denver, CO. Over the past three years, grouted shaft helicals have been used successfully on remedial and new construction projects all across North America. The authors have studied several construction projects in a variety of soil conditions to compile a list of practical design guidelines. Those guidelines include installability of grouted shaft helicals based on soil type, equipment requirements, grout selection, and theoretical vs. actual load capacity. In a number of cases, full-scale, field load tests were conducted in both granular and cohesive soils and the results broken down between tip resistance on the helix bearing plates and friction resistance on the grouted shaft. Data is presented which will further efforts to develop a design model and method to accurately predict the axial and lateral capacity of grouted shaft helicals.

Jan 1, 2003