Search Documents

Characterising the weight percentage of each mineral in base metal ores is an integral part of assessing the quality of an ore in terms of its processing properties. The Rietveld method, which uses X-ray diffraction data, has been applied to routinely quantify the minerals in lead/zinc and copper ores from Mount Isa Mines Limited and supergene copper ores from Ernest Henry Mining as well as their related products from the concentrators. The Rietveld method has been tested by comparing Rietveld mineral data with a standard sample with known mineral weight percentages and comparing Rietveld mineral data with mineral data calculated from elemental assays where the element only exists in one mineral such as lead in galena. Where this latter situation does not occur, the Rietveld method has been checked with both elemental and optical microscope data. In all cases, there is a good correspondence between the Rietveld data and the data it was checked against with absolute differences generally in the range of 0.5 to 3 wt per cent. The Rietveld method generally quantifies all minerals occurring over 1 wt per cent in one analysis and is less expensive and more routine compared to traditional methods such as optical microscope point counting. The Rietveld method can be applied to many stages of the mining cycle such as exploration, feasibility studies, mining, minerals processing and for environmental studies.

Jan 1, 1998

Aspects of the formation, decomposition and acid solubility of zinc ferrite were examined to find potential ways of increasing the recovery of zinc from a calcination process of mineral concentrates. Ferrite can begin to form within 2 hours at 450¦C. while complete reaction can occur after 35 minutes at 700¦C. The nature of the starting materials has a pronounced effect on the rate of formation and below 700¦C. ZnSO4 and Fe2O3 proved to be the least reactive of the materials investigated. It is possible that iron in a mineral admixed h sphalerite can be converted to a relatively inactive form, however, it does not seem possible to prevent zince f formation when iron is in the sphalerite lattice. At the two temperatures examined, 650¦C. and 700¦C, the presence of SO2 in the atmosphere accelerate .e formation of ferrite. Prolonged exposure to such atmospheres, however, caused the ferrite to decompose to ZnSO4 and Fe203. The optimum temperature for decomposition was 650¦C. and it was virtually complete within 2 hours in an atmosphere of 10% SO2 in air. Zinc ferrite was also decomposed by CO at low concentrations, and by heating with limestone at 1000¦C. for at least 2 hours. The solubility of zinc ferrite in acid was influenced by the starting materials used. As both the reaction temperature and the time at temperature increased the acid solubility decreased. The acid solubility was a minimum when the ___i_.. n - I -r~...................c -..... F, fe..i+e --A frn... A01- +^ Z(lo/

Jan 1, 1970

There are significant Mineral Resource and Reserve reporting challenges facing a mining company operating in the global arena. This paper specifically examines the Mineral Resource and Reserve reporting challenge facing BHP Billiton. The changing regulatory environment creates a significant challenge for global mining companies when reporting Mineral Resources and Reserves. The development and implementation of internal policies and standards for collecting and collating resource and reserve information is required for corporate governance, however the challenge is then to report this information publicly in such a way as to comply with the various codes and requirements in the many jurisdictions in which the company is required to report. The move to an International Code is not only desirable but is an essential requirement in todayÆs global market. The agreement to report using a single code internationally is however only the first step. A truly practical international reporting system must have common definitions and guidelines for interpretation as well as an international approach to the definition of a Competent Person, and even more importantly a common acceptance of that code by the relevant investment regulatory bodies. Without the universal acceptance of the concept of an international reporting code by the major regulatory bodies, implementation of such a code will be limited. With the major global mining companies seeking to raise capital in the USA, the worldÆs largest capital market, the Securities and Exchange Commission (SEC) and its approach to reserve reporting is becoming increasingly important. The development and implementation of an International Code must gain the support and acceptance of the SEC if it is to be successful.

Jan 1, 2002

By H Waterer, L Zheng, T Kalinowski

The Hunter Valley Coal Chain (HVCC) consists of mining companies, rail operators, rail track owners and terminal operators, together forming the worldÆs largest coal exporting facility. In 2008, the throughput of HVCC was about 92 million tonnes, or more than ten per cent of the worldÆs total trade in coal for that year. The coal export operation generates around $15 billion in annual export income for Australia. As demand has increased significantly in recent years, and is expected to increase further in the future, efficient supply chain management is crucial. The Hunter Valley Coal Chain Coordinator Limited (HVCCC) was founded to enable integrated planning and coordination of the interests of all parties, thus improving the efficiency of the system as a whole. One of the many planning challenges faced by the HVCCC is that of annual maintenance planning. Different supply chain elements, such as trains, railway track, terminal equipment and load points, must undergo regular preventive and corrective maintenance, leading to significant reductions in system capacity (up to 15 per cent). However good alignment of the maintenance tasks can reduce their impact, and the HVCCC undertakes an annual process to ensure the impact of maintenance on the supply chain capacity is as small as possible. This is achieved in an iterative negotiation process between HVCCC and individual service providers. In the past, maintenance schedule optimisation was largely manual, which for the more than 1000 tasks involved is quite labour-intensive.In this paper the authors describe an approach developed at the University of Newcastle in partnership with the HVCCC to automate this schedule optimisation process. We will discuss our experience in applying exact (mixed integer programming) and heuristic techniques from mathematics and computer science to address the problem. This work is anticipated to lead to new decision-support tools for the HVCCCÆs capacity planning team.

Sep 26, 2011

In the years prior to the outbreak of war in 1939 Australia's production of copper had declined from a peak of about 80,000 tons in 1911-1915 to approximately 25,000 tons in 1939. This production met the need of the slowly growing national requirement and gave an excess for export. However, with the intensification of the war effort in 1942 due to the imminence of a Japanese invasion of this country, or at least a blockade of the sea lanes, it became necessary to expand production of armaments, and consequently the demand for copper increased beyond the capacity of the industry. Importation of copper to Australia during the period 1940-1944 was 131,000 tons.When exploration of the Mount Isa orebody was first being carried out in 1928, No. ID diamond drill disclosed the presence of some copper ore lying outside the limits of the Black Star orebody2, but it was not until 1941-1942 that the development of No. 7 level in the Black Star orebody enabled the existence of a lode of copper ore of economic grade to be established. At the request of the Commonwealth Government of the day a programme of development for copper production was undertaken whilst lead smelting was continued as before the war.A series of flotation tests on up to 1,500 tons of ore at a time, was undertaken and the concentrate so obtained was stockpiled. These tests were conducted, using one section of the lead mill, and demonstrated that a concentrate grade of 22-23% Cu with a recovery of 80-85% might be expected.These recovery figures were afterwards much improved, and 93-95%was obtained before the close of smelting in 1946.

Jan 1, 1953

By Ushakov S

New geological and geophysical in vestigation including our detailed field observation in different regions of the Koryak upland testify that Nor- theastern Eurasia margin eastward of the Ochotsk-Chukotka belt is composed of a collage of allochtonous terranes arcs and sedimentary filling of back- arc basins, which bordered North East Siberia and Chukotka (1)1). Ancient island are assemblages are the most tipical for this region (2-4; shown by heavy line). They are marked by long (500-1000 km) volcanic belts which become younger towards the Pacific up the Latest Jurassic-Neocomi- an (2) to Late Cretaceous (3) and Pale- Gene (4).

Jan 1, 1987

By Dight P. M, Dugan K. J

Design approaches for the artificial support of open pit walls have been reviewed and the main factors affecting support performance have been identified. An example of passive support in a potentially unstable pit wall has been used to demonstrate the importance of slope displacement as part of the support design process.

Jan 1, 1989

By S Ellis, J McMullen, M Habner

A new leaching regime was implemented at Kalgoorlie Consolidated Gold MinesÆ (KCGM) Gidji plant on a cyanide leach of ultra-fine ground sulfide concentrate. High lime concentration and lead nitrate were used to overcome the refractoriness of the fine sulfides (high reactivity of fine sulfides with the presence of gold tellurides). The leach pretreatment stage was shown to be detrimental and was shut down. Lime titration was introduced as part of the process control. It was shown that the leach could be performed at low dissolved oxygen, (ie 3 - 5 ppm) to avoid sulfide oxidation and the associated high cyanide and lime consumption. Plant results showed reduced cyanide consumption (40 per cent) and an accelerated leaching rate, whereby most of the gold was dissolved in 24 hours compared to 72 hours used previously. Similar work was performed at KCGMÆs Fimiston plant, which leached a combined ultra-fine ground sulfide concentrate along with the slimes fraction from hydrocycloning the bulk flotation concentrate. The use of lead nitrate, high lime and carbon-in-leach generated a faster leaching rate and minimised adsorption of gold on fine pyrite particles. The grind, previously controlled with a P80, was replaced by a P98 to give a better operational indication of top size hydrocyclone performance. Before the implementation of the changes, average leach residues for slimes and UFG were respectively 4.0 g/t and 5.5 g/t. With the modifications to the leaching regime, average leach residues were lower by 1.5 - 2.0 g/t. Whilst significant improvements have been demonstrated, further work is progressing at KCGM to further reduce ultra-fine concentrate leach tail grades, and also to improve the understanding of concentrate refractoriness and the factors responsible for differences between laboratory and plant leach results. Estimated profits since the implementation of the new approach are in the range of $A3.5 million per year.

Jan 1, 2005

Information from bores in the LatTobe Valley has been accumulating for over fifty years, and the manual extraction of details has become a limiting factor in their use.Punched card equipment, installed by the State Electricity Commission for accounting purposes, was known to be available for reasonable periods, and it was suggested that this could help in the extraction of data from the voluminous records.Investigation showed that they could be substantially duplicated on cards, with consequent gains on many operations; the cards being regarded as an auxiliary to the existing records.BRIEF DESCRIPTION OF RECORDSAs a bore is drilled a continuous record of the strata is kept, together with notes on the presence of water or any unusual features which the driller may observe.When coal is struck, samples of each ten feet are usually sent for analysis.The location and surface level of each bore is fixed by surveyors, and details of dates and methods of drilling are also kept.Bores are allocated numbers, prefixed by the name of the parish within which they are drilled. Numbers are allocated in conjunction with the Department of Mines, to avoid duplication.Records of strata and analyses are kept in folders, with 100 bore numbers per folder.Standard plans are drawn, showing the locations, bore numbers and surface levels. For each bore they also show the depth and thickness of coal struck, and the total depth drilled.Cross sections are then drawn, connecting the various coal seams, which have been identified by the geologist.

Jan 1, 1960

The overall mineral assemblage of the Broken Hill orebody is similar to that of a skarn. However unlike the classical skarns it does not represent contact metamorphism of pre-existing limestone beds. It is a stratiform accumulation of exhalative-sedimentary silica, sulphides, (Ca, Fe, Mn) silicates and carbonates, fluoride and phosphate that has later undergone regional metamorphism. The resulting development of coarse-grained quartz, sphalerite, galena, rhodonite, bustamite, mixed carbonates, fluorite, apatite and many minor phases has produced a sulphide-rich skarn- like mass that like many others of its kind, might best be referred to as a stratiform skarn. Recent investigations of occurrences of this type are showing that the incidence of concentrations of particular metamorphic minerals in and adjacent to such orebodies are closely related to bedding and to former sedimentary facies patterns. From this it appears that the mineral assemblages may be used to deduce not only the nature of the materials laid down in the beds, but also the physico-chemical conditions under which sedimentation took place. Several stratiform deposits, including Broken Hill, are used as examples to show that variations in these conditions may have a profound influence on the subsequent response of the rock to regional metamorphism and hence on the mineral assemblages that finally develop.

Jan 1, 1983

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. C. H. MARTIN) IN PRESENTING THE CERTIF1CATE TO SIR GEORGE FISHER, C.M.G.Members of The Institute, distinguished guests, of which there are many, ladies and gentlemen, you are welcome.And might I add a special welcome to Lady Mawby and Lady Fisher and to Sir George's only son Peter, who with his wife, Betty and one of Sir George's three daughters, Helen, are present this evening, and also to Sir Maurice's son, Colin, and Colin's wife, Jay, also in our company.The family presence must surely be a great source of pleasure and satisfaction to all those so intimately concerned.It is hardly. necessary for me to state the sole and only rC'l.son for our presence here tonight, which is to conJer on Sir George Fisher and Sir Maurice Mawby Honorary Membership of The Australasian Institute of Mining and Metallurgy, and at the same time to acknowledge two people who have rendered great service to the mining industry albeit tinged with sadness to all of us in the knowledge that from now on their influence may diminish.

Jan 1, 1976

Results of blasting trials conducted at Gregory Mine, a large open cut coal mine situated in the Bowen Basin, show that fragmentation was improved or equalled whilst reducing the amount of explosives previously required. This was achieved by a system of deck loading whereby two or more explosive charges, separated by air gaps, were positioned in the blast hole, thereby extending the effective explosive column whilst minimizing the total explosives required. In the three trials to date, a saving of approximately 213 kg of ANFO per blast hole was achieved. This represented an approximate 20% reduc- tion in ANFO requirements.

Jan 1, 1989

By K McNabb, M H. Turner, P A. Jenkin

Mining of the Agnew nickel deposit commenced in 1970 using a variety of underground mining methods, though with mixed success due to the difficult ground conditions. WMC Resources Ltd acquired the operation in 1989, and commenced nickel production with an open pit. In 1995 all production reverted to the rejuvenated underground mine, using exclusively SLC (sublevel caving) methods. Currently the mine produces 1.4 Mt per annum, at an average grade of 1.74 per cent Ni. Underground mining of the Perseverance orebody has always presented significant challenges due to the difficult ground conditions in the weak and altered ultramafic rocks. The range of problems include areas of swelling minerals, intense and extremely weak shear zones, relatively high in situ stress, and in other areas very brittle rocks. Under these conditions rock mechanics input has been and remains a critical element of the mining strategy. Severe ground behaviour difficulties down to a depth of 500 m below surface prompted a review of the mining strategy for the large disseminated nickel orebody, including evaluation of alternative mining methods. However, sublevel caving was ultimately selected as the preferred method, and a re-design of the SLC cross-cut layout followed. A selection of rock mechanics investigations of interest are described, including complex virgin stress measurements, detailed ground behaviour monitoring, and the use of non-linear stress analyses to re-design the mine layout. Subsequent ground behaviour, support design and production scheduling are also described.

Jan 1, 2000

By Clark G

The latest addition to the grinding circuit at Bougainville Copper Limited is another 5.5m by 7.3m primary mill (No.13). The mill can operate in a primary or secondary mode. Its distinguishing feature is its capability for speed variation, by means of a cycloconverter-fed synchronous ring motor. The engineering and metallurgical reasons for selecting such a drive system are described together with aspects of the installation and commissioning. Results of investigations into the relationship between mill speed and grinding efficiency are presented. It is concluded that mill speed variation within the range 70 to 80% of critical speed has very little effect on grinding performance. Beyond this range, grinding performance deteriorates. The same conclusions were reached when mill speed was varied at reduced ball charge levels.

Jan 1, 1986

By M Roberts

The aim of this paper is to evaluate the technical feasibility of application of the electric monorail as a haulage system in hard-rock underground mining in Australia, in comparison to conventional truck haulage systems. The elements of the system being investigated include mine design and layout, installation, loading and unloading subsystems, tramming speeds, cost and productivity, automation, ground support, safety and environmental factors. Electric monorail systems are potentially more cost-effective due to a range of factors: only the one system may be needed for the transportation of workers, material and rock; and excavations for monorail haulage can be smaller and mined at much steeper gradients than for truck haulage. The smaller excavation size also reduces the need for costly ground support and û in another important measure for the health and safety of mine workers, and for energy savings û it reduces ventilation requirements. Electric monorail haulage technology is being applied in hard rock mines in South Africa and considerable benefits have been realised by the industry in that country. In Australia, mine designs for metal mines generally remain based on truck haulage and/or shaft hoisting systems. There is a tendency to apply these haulage systems to every orebody. For the industry to achieve sustained growth against a backdrop of volatile diesel prices and environmental concerns, new generation underground haulage systems are required. The monorail haulage system offers opportunities in improving materials handling efficiencies in underground mining operations. This paper examines the application of monorail haulage in metalliferous underground mining, presents comparative data with track and trackless haulage systems and develops concepts for system application in combination with conveyor belt haulage and narrow vein mining situations.

Jan 1, 2005

By S R. Grano, M Vera

This paper deals with two separate case studies investigating the froth phase performance and characterisation of two industrial rougher/ scavenger flotation circuits. Froth phase performance was quantified using a mass balance approach to estimate froth zone recovery. Measured characteristics of the froth phase included frother solution concentration determined by gas chromatography, and the time taken for an equilibrium froth sample to decay to one-half of its original froth height. The latter measurement is referred to as the æfroth half-lifeÆ and is strongly linked to froth stability. Special methods and techniques developed to preserve frother in solution and to measure froth half-life are briefly described. The frother type in the first case study was a mixture of straight and branched alcohols, whilst the frother type in the second case study was a mixture of alcohols, aldehydes and triethoxybutane. The first case study focussed on a flotation circuit treating a low-grade ore containing only a small fraction of floatable copper sulfide minerals, while the second case study focussed on a flotation circuit treating a higher grade complex sulfide ore containing significant quantities of chalcopyrite, galena, sphalerite and pyrite. It was found that froth zone recovery of valuable mineral generally decreased down-the-bank of the two industrial rougher/scavenger circuits. Moreover, decreases in froth zone recovery significantly limit the overall cell recovery of valuable mineral achievable from the plant scavenger cells. However, the decrease in froth zone recovery could not be linked to the removal of frother from the pulp solution to the concentrate product in the preceding rougher flotation stages. Measurements of residual frother in solution suggested that, approximately, only five to ten per cent of the added frother was removed into the rougher/scavenger concentrate, with the remainder appearing in the scavenger tailings. This finding suggested there was apparently adequate frother in solution in the scavenger stages.

Jan 1, 2005

By Bratt G. C, Horsham T. R, Langlois D. R

Mercury is precipitated from weakly acidic sulphuric acid plant waste liquor at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited. Factors determining the choice of process and reagent, as well as details of process development including scale- up, and the time scale of implementation are outlined. The plant is designed for a maximum flow of 120 m3/h.of liquor containing mercury and saturated with sulphur dioxide. Mercury is precipitated by fluidised beds of aluminium pellets contained in lead columns. Liquor is then clarified with plate and frame presses. Experimental work on the mercury precip- itation reaction was conducted in three phases involving a scale-up of 100 times in equipment size. Extensive pilot filtration work was carried out on a 1 m2 press. Scale-up of 120 times was required for specification of plant filters. The basis of scale-up is outlined.

Jan 1, 1977

By A Sinuhaji, H Kalangi, T B. Setyoko

Ore fragmentation at the DOZ block cave mine is highly variable, both as a function of rock type and column height of draw. Initially, the mine was constructed and equipped with limited capability to handle drawpoint oversize material. Significant issues with drawpoint availability and achieving overall mine production targets resulted. A suite of secondary sizing tools was added to the mine equipment fleet over a one-year time frame. Although significant oversize continues to be experienced, use of the correct secondary breakage tool for each particular oversize or hang-up occurrence has resulted in increased drawpoint availability, production rate, draw compliance, and operator safety. Currently, a range of secondary breakage techniques is being utilised to size material for delivery to the primary crusher. Run-of-mine material (3) is directly mucked to ore passes fitted with grizzlys that have one-metre square openings. Ore containing small boulders (>1 m3, 3) is loader-trammed to ore passes fitted with rockbreakers. Medium-sized boulders (>2 m3) accessible from the drawpoint are drilled with Sandvik Tamrock Commando drills. Boulders hung-up within the drawbell are drilled and charged with a Sandvik Tamrock Secondary Breakage Unit. Compacted, fine-grained muck is blasted utilising 55 mm cartridge powder concussion bombs.

Jan 1, 2005

This paper presents a review of heat illness in mining, including reference to several recent investigations by the author. Heat illness is a collective term, covering the conditions of heat stroke, heat exhaustion, heat cramps and miliaria rubra. Heat stroke is life-threatening and is by far the most serious condition. It is rare in mining, if appropriate control measures are instituted. Heat exhaustion is primarily due to hypohydration, following prolonged sweating in hot conditions. Symptoms include fatigue, headaches, dizziness, anorexia, nausea, vomiting, shortness of breath, or brief syncope. Confusion, ataxia, prolonged unconsciousness or convulsions are strongly suggestive of heat stroke. Heat cramps are painful involuntary contractions of skeletal muscle associated with work in hot conditions. The limbs are usually involved and the spasms typically last a few minutes, during which the affected part of the body is incapacitated. Heat cramps tend to occur in heat exhaustion, when hypohydration becomes marked. Miliaria rubra is a skin rash caused by extravasation of sweat into the skin, as a result of obstruction of the sweat glands. It occurs after prolonged and profuse sweating in hot environments. It can take three to four weeks of sedentary duties, in an air-conditioned surface environment, for the condition to resolve. Heat illness would be unlikely in underground mining, if the thermal environment was sufficiently well controlled by ventilation and refrigeration. This is however, often not practicable. Where engineering controls alone cannot provide sufficient control of risk, the residual risk can be assessed using an appropriate heat stress index. While procedural controls may further reduce the residual risk, it is important to remember that these are less reliable than engineering controls and cases of heat illness may still occur. Procedural controls include the application of heat stress limits, education, hydration, self-pacing, early symptom reporting, medical advice, acclimatisation procedures, air conditioned accommodation, support to achieve a healthy body mass index, and an effective emergency response capacity.

Jan 1, 2005

Resource developers in Papua New Guinea (PNG) are now, more than ever before, confronted with land-owner related issues that can hinder their corporate objectives.Development of PNG's custom-arily owned land since independence has brought sudden changes with mixed success. Exploitation of mineral resources has had its share of problems, and Highlands Gold Limit-ed's (HGL) endeavours in the central Highlands of PNG are no exception.

Jan 1, 1994