Search Documents

By S. H. Penn

One of the more challenging aspects of the unfolding age of space travel centers about the opportunity for man to use the natural resources of other worlds. The first of the extraterrestrial worlds to be exploited will be the moon. After only a scant few thousand years of scratching the earth's crust, man will embark upon a venture that for centuries has excited the imagination of many (while staggering that of most) and may become a reality within the next decade. There has never been a time when so much money and effort will have been expended to exploit an area about which so little is known. Paradoxically, this effort combines much of the detached objectivity so typical of our analytical time with the proverbial optimism of the indefatigable prospector. As the earliest manned lunar missions will be brief and exploratory in nature, astronauts will not be expected to attempt to exploit any of the possible lunar natural resources. In later missions, with a more extended period of time available for the astronauts to stay on the moon, it may be desirable or even necessary to "live off the land". The resulting exploitation of lunar resources will be intended primarily to reduce the dependence of manned missions upon terrestrial logistic support and to reduce the cost of maintaining lunar bases.

Jan 3, 1966

By W. H., Bassett

IN January, 1926, the writer began a study of the commercial value of beryllium in its relation to copper. The purpose of the investigation was not to make a mere laboratory study of the characteristics of beryllium-copper alloys, but to determine under mill conditions the behavior of copper when alloyed with beryllium and when other metals were added to such alloys; in other words, it was considered important to know whether the alloy bars could be hot-rolled or cold-worked, and what limits in composition would have to be established for these two methods of working. Consequently, more stress has been placed on the practical application of the alloys in engineering and commercial use than on a discussion of the metallography of the specimens examined, although this part of the matter has not been entirely neglected. Credit should be first given to G. Oesterheld,1 who, in 1916, published the copper-beryllium equilibrium diagram. Fig. 1 has been copied from the original article with the simple substitution of English words. It will be noted from Fig. 1 that alpha solid solutions are formed, up to about 1.5 per cent. Be (10.5 atom.). The freezing-point curve, after falling from 4.2 per cent. Be (23.5 atom.), enters into a very complicated form over the entire beta region. There is a possible compound, Cu2Be, at about 6.5 per cent. Be (32.3 atom.). The pure gamma range extends from 11.2 to 12.2 per cent. Be. (46.5 to 49 atom.), after which the liquidus rises rapidly to 30 per cent. Be. (75 atom.). The delta solution extends from 25 per cent. to an unknown percentage of beryllium. There is a eutectoid point at 575" C., extending from 1.5 to 11.2 per cent. Be., the maximum time interval of which occurs at 6 per cent. Be. Below this line the beta solution is described as breaking up into alpha and gamma. Microscopically, the eutectiferous alloy thus formed closely resembles pearlite, and requires a high magnification for its resolution.

Jan 1, 1927

By W. R. Barclay

IN MY general contact with industry I have become more and more impressed with the need for the closest possible co-operation between engineers and metallurgists, and particularly with the need for appreciation of the work that each group is doing to assist the other. Also, I am convinced that from time to time it. is vitally important to a true perspective of human progress in all its branches, and certainly a salutary corrective of undue optimism and pessimism to endeavor to carry the mind hack over certain periods in the advance of technical knowledge, and form some kind of broad estimate of what has been accomplished in the application of science to industry in the fields with which we, as individuals or groups, may for the time being be concerned. We cannot without some appreciable mental effort realize what our forerunners have dine For us. If the young engineer or metallurgist entering industry today could be suddenly transported to a quarter of a century ago, and be compelled to work with the materials then available and within the limitations of knowledge then attained, he would, on his return to present-day life, have a much greater appreciation of what has been accomplished before lie arrived on the scene, and, what is even more important, a far more acute sense of its inherent value to his profession. I propose here merely to indulge in a general summary of the subject of improved engineering metals and alloys rather than in details, and to deal exclusively with developments within my own experience.

Jan 1, 1938

By FREDERICW K. BRADLE

I HAVE been puzzled by two lines of thought'; one emanating from Washington, D. C., to the effect that we must all cheer up, that in a very short time, measured in terms of months, prices would begin to recover, business would become normal, and prosperity would continue on its way just as before the interruption of a year ago; and a second, coming from certain industrialists and economists, expressing fears that all commodity prices were in for a long downward trend, which would cause much unemployment, eventually drag down wages and so restrict purchasing power as to further aggravate the situation. One basis for the fear of a downward trend in commodity prices' is that ifter great wars a depression could last for something like 40 years-the downward trend to such a depression after our recent World War having been postponed for some reason or other; and the basis for another fear was that the production of gold was becoming less. I had 'also been trying for some time past to refresh my recollection as to how my ow11 particular lead interest climbed out of the depression of 1893; and as all the metals have had, and still have. relative values and prices, I can best express what I have in mind by talking principally about lead.

Jan 1, 1930

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is, relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.1 Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.2 Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general; development of the area was slow. To the south, the heavy. mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions.3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west. of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of-the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.2,3 The axis of the syncline dips to thee southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.4 Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary, band of secondary clays found intermittently, at points, across the, south of the province where glacial action did not disturb or remove them.8 In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to. 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.9 It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1952

By J. F. Enrietto

Internal friction measurements were used to determine the effect of manganese on the solubility and precipitation kinetics of nitrogen. Manganese, in concentrations up to 0.75 pct, has little effect on the solubility at temperatures above 250°C. On the other hand, at Concentrations as low as 0.15 pct, manganese inhibits the formation of iron nitrides, especially Fe4N, even though it may not form a precipitnte itself. The precipitation and solubility of carbides and nitrides have been extensively investigated in the pure Fe-C and Fe-N systems.1-3 In recent years, some effort has been ispent in studying the influence of substitutional alloying elements on the behavior of carbon and nitrogen in ferrite.4 -7 In particular Fast, Dijkstra, and Sladek have investigated the effect of 0.5 pct Mn on the internal friction and hardness during the quench aging of Fe-Mn-N alloys.', ' They found that at low temperatures (below 200°C) the presence of 0.5 pct Mn greatly retarded quench aging. For example, after 66 hr at 200°C very little precipitation had taken place in the iron alloyed with manganese, whereas precipitation was complete after a few minutes in a pure Fe-N alloy. The effect of varying the manganese content and the details of the precipitation process were not mentioned in these papers. Fast' postulated that manganese causes a local lowering of the free energy of the lattice with a resulting segregation of nitrogen atoms to these low energy sites. The segregated nitrogen atoms are bound so tightly to the manganese atoms that they cannot form a precipitate. The internal friction measurements of Dijkstra and Sladek tended to confirm the concept of segregation of nitrogen around manganese atoms, and the increase in free energy on transferring a mole of nitrogen atoms from a segregated to a "normal" lattice site was computed to be - 2800 cal. Dijkstra and Sladek9 distinguished between two types of precipitates: ortho, a nitride of appreciably different manganese content than that of the matrix, and para, a nitride with a manganese content essentially that of the matrix. With each type of precipitate a solubility, again designated ortho or para, can be associated. Since the internal friction maximum in alloys which were aged several hours at 600" C dropped almost to zero, Dijkstra and Sladek9 concluded that the ortho solubility must be very low. The effect of temperature on the ortho and para solubilities has no1: been investigated. There are obviously several gaps in our knowledge concerning the influence of manganese on the behavior of nitrogen in a-iron. It was the purpose of the experiments described in this paper to determine the following: 1) The ortho and para solubilities of nitrogen as a function of temperature. 2) The details of the precipitation process at elevated temperatures. 3) The effect of varying the manganese concentration on the above phenomena. EXPERIMENTAL PROCEDURE Internal friction is conveniently employed in studying the precipitation of nitrides and/or carbides from a -iron because it is one of the few parameters, perhaps the only one, which is not affected by the presence of the precipitate itself. For this reason, internal friction techniques were heavily relied upon in the present experiment. A) Preparat of -. All specimens were prepared from electrolytic iron and electrolytic manganese. Alloys containing 0.15, 0.33, 0.65, and 0.75 wt pct Mn were vacuum melted and cast into 25 lb ingots. After being hot rolled to 3/4 in. bars, the ingots were swaged and drawn to 0.030 in. wires. The wires wen? decarburized and denitrided by annealing at 750° C for 17 hr in flowing hydrogen saturated with warer vapor. To obtain a medium grain size, - 0.1 mm, the wires were then heated to 945oC, allowed to soak for 1 hr, furnace cooled to 750°C, and water quenched. Subsequent internal friction measurements showed that this procedure reduced the nitrogen and carbon concentrations of the alloys to less than 0.001 wt pct. The wires were nitrided by sealing them in pyrex capsules containing anhydrous ammonia and annealing them for 24 hr at 580°C, the nitrogen being retained in solid solution by quenching the capsule into water. Immediately after quenching, the wires were stored in liquid nitrogen to prevent any precipitation of nitrides. By varying the pressure of ammonia in the capsule, it was possible to produce any desired nitrogen concentration. B) Internal Friction. The internal Friction measurements were made on a torsional pendulum of the Ke type,'' a frequency OF 1. or 2 cps being used. For

Jan 1, 1962

By Paul E. Rosten

Introduction This papers describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Co. to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Co. operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously (Lindroos and Koski, 1966; Villar and Dawe, 1975; Koski, 1977). Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and fur¬nished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate¬kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to: (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1981

By M. C. Manderson

The sharp drop in world phosphate demand that took place in 1975 due to temporarily high prices, now seems to be reversing itself. And prices for both phosphate rock and phosphate fertilizers, which declined dramatically from their 1975 highs, now appear to be bottoming out. This recent price weakness has delayed new mining ventures that had been planned for completion by around 1980. While there is ample capacity to supply near-term rock needs, the stage seems to be emerging for a better supply-demand and price environment in the late 1970's and early 1980's.

Jan 1, 1979

By Robin O. Williams

AN investigation has been made of the Ni-Cr system for the purpose of elucidating certain points, namely the nature of aging in both terminal solid solutions and the nature of the phase diagram. Information pertaining to solubilities and precipitation has been obtained. Experimentation Five alloys, Table I, were arc melted in a cold copper crucible using electrolytic chromium and car-bony1 nickel, both dry hydrogen treated. These 100 g buttons were homogenized 24 hr at 1300°C in dry hydrogen and air cooled. Powders were prepared by filing or pulverizing and subsequent heat treatment was done in vacuum or helium using titanium chips as a getter. Powder of —80 mesh was filed from the 60 pct Ni alloy quenched from 1000°C and was sealed in silica under vacuum using a 250 °C outgassing. After aging as indicated in Table I1 the lattice parameters were measured on the quenched samples using the standard cos" 6 extrapolation. These parameters are considered accurate to roughly 0.0001A. In all cases chromium lines of 2.8812 ± 0.0005Å at 30°C were found. Drastic quenching from sufficiently high temperatures produced very sharp body-centered-cubic lines in the first four alloys without indications of transformations. Temperatures to 1250°C were used. Solid samples less than 1/16 in. thick were quenched in water without transformation and the powders could be adequately quenched in small helium filled thin wall silica tubing using a water quench. For those powder samples which were quenched from the two phase field the relative intensity of the body-centered-cubic lines and the face-centered-cubic lines were estimated and extrapolated to give the indicated solubility data in Fig. 1. The data for the two higher alloys were somewhat limited, the plotted points being the lowest temperature where no nickel phase was found. Neither filing, abrading, pulverizing, nor cooling to —190°C produced any new diffraction lines for solid samples quenched from the single phase region, nor did the character of the body-centered-cubic lines change Single phase body-centered-cubic powders likewise did not change on cooling to —190°C. Also, samples which had some precipitation due to inadequate quenching showed no additional changes under these conditions. The first change apparent by X-ray diffraction form samples quenched almost fast enough to prevent precipitation was the diffuseness of the body-centered-cubic lines, particularly on the low angle side, For slower cooling rates the diffuse face-centered-cubic lines appeared. Work on the large grained castings showed profuse streaking through some of the Laue spots while oscillating patterns showed broad body-centered-cubic and face-cen-tered-cubic lines as well as some new lines. For the 23.6 pct Ni alloy the new lines corresponded to 2.16, 1.96, and 1.86A and were more similar in character to the face-centered-cubic lines than the body-centered-cubic lines. Samples which were air cooled gave only face-centered-cubic and body-centered-cubic lines which were still broad. One pattern indicated that face-centered-cubic (111) plane was parallel to a body-centered-cubic (110) plane. For those samples which were examined by light microscopy there were details which were not resolved. However, varied and beautiful structures were obtained. Fig. 2 is of an alloy quenched in a helium filled silica tube from the single phase region and shows particles associated apparently with dislocations which are arranged in low angle boundaries. Finer, general precipitation has also taken place within the grains. Figs. 3 to 5 show the variety of structures produced in these alloys on continuous cooling. It appears that there are four distinct modes of precipitation as evidenced by these, figures. Annealing these structures at higher tem-peratures in the two phase field gives structures as shown in Fig. 6, which shows nickel plates in the chromium matrix which reprecipitated nickel on a much finer scale of the final quench. Lower annealing temperatures and shorter times naturally give finer plates of the nickel-rich phase. Samples of the first four alloys were annealed for appreciable times between 900º and 1250°C and gave structures like Fig. 6. The relative amounts of the two phases were measured and extrapolated to give solubility data as indicated in Fig. 1. The point at 1250°C was deduced from data of Oxx.1 These and most of the other samples were checked for ferromagnetism but none was apparent. In fact, it appeared that the magnetic susceptibilities were not more than three times that for paramagnetic chromium. Discussion In Fig. 1 it is seen that the solubility of nickel in chromium can be represented by a slightly curved line on the usual log X vs 1/T plot, These data are believed to be accurate to roughly 5 to 10º. There is only fair agreement with the data of Taylor and

Jan 1, 1958

By W. E. Bonini, E. A. Hickok

IN the course of an investigation directed toward expanding ground-water facilities in Essex and Morris counties, New Jersey, the Board of Water Commissioners of the city of East Orange authorized a seismic-refraction survey' for the purpose of de-lineating bedrock topography below unconsolidated overburden. Results of the survey were highly satisfactory and led to the preparation of a comparatively detailed bedrock contour map. Knowledge of the bedrock depth and configuration was an important aid in selection of sites for test drilling. The portion of the East Orange Water Reserve under consideration is in the flood plain of the Pas-saic River about 10 miles west of Newark, N. J. The flood plain is about 175 ft above mean sea level and is bordered by low hills rising to elevations of approximately 250 ft. The bedrock underlying the Water Reserve consists of sandstone and shale of the Triassic Brunswick formation and is covered everywhere by deposits of unconsolidated glacial outwash sand and gravel, lacustrine clay, and recent river silt as much as 150 ft thick. Yield of wells in the sandstone and shale averages 100 to 200 gpm. Since production wells constructed in the sand and gravel aquifer in the buried river valley shown on the contour map (Fig. 1) yield 300 to 1400 gpm, it was proposed to locate additional production wells in this buried valley, where the yields per well would be maximum. In 1939 and 1946 the East Orange Water Dept. had electrical-resistivity surveys made to determine depths to bedrock. From the resistivity data the exploration company prepared a bedrock contour map. A well field expansion program begun in 1955 utilized this information to locate sites for test wells along a predicted northward extension of the buried valley in which existing production wells are located. After several test wells (wells 201-205) had been drilled, it became apparent that the resistivity information was unreliable." For example, test well 201 recorded bedrock at a depth of 72 ft, whereas the resistivity depth determination was 130 ft. As a consequence, the test drilling program was temporarily suspended and a seismic survey was under- taken to determine the topography and extent of the buried valley known from well records to underlie the existing well field. In the first phase of this study, several seismic shot point locations were placed at sites where well logs had been obtained previously. This procedure is necessary in a new area to determine whether the seismic method is applicable and what degree of accuracy is to be expected. At the East Orange Water Reserve, depths obtained from the shot points near test wells 202, 203, and 204 were within 8 to 11 pct of the depths logged (Table I). With this assurance that accurate results could be obtained, additional seismic spreads were located on the Water Reserve. Using a portable refraction seismograph, in the fall of 1955 a crew of four men shot a total of 29 reversed seismic spreads in a period equivalent to six field days. Charges as heavy as 3 1b of 40 pct dynamite were necessary at a few places to overcome ground vibrations caused by traffic on nearby highways. At most other sites, a 1-1b charge was sufficient. Travel-time plots were made for all spreads, and depths and true velocities were calculated according to formulas for multiple sloping layers by Ewing, Woollard, and Vine.' The plot of spread 7 (Fig. 2) is typical of the short spreads in which bedrock was shallow—about 50 ft in this case. Where there were not enough arrivals through the bedrock to define the high velocity bedrock line, the spreads were lengthened. This was done by placing shots on line several hundred feet away from each end of the line of geophones. It was then possible to construct complete reverse plots for both short and extended shot points (see spread 27, Fig. 3). Four individual depths were calculated from each extended spread. Three and in some cases four seismic layers were observed. The surficial layer had a velocity range of 900 to 1200 fps, the lowest velocity recorded. This seismic layer is above the water table and is interpreted as recent river silt. The bedrock had the highest velocities, which ranged from 10,600 to 16,400 fps. Intermediate velocities ranged from 4500 to 6800 fps. In every case the intermediate layer was within

Jan 1, 1959

By Robert C. Paddock

INTRODUCTION A way of producing 3,000 tpd from the El Mochito Mine was needed. Of this production, 2,000 tpd must come from the San Juan orebody. The original sub-level stoping method did not give satisfactory results due to ground instability, and the highly irregular ore/waste contacts encountered . The experience gained from the initial system helped guide research into the ground instability problem. Results from this work, combined with knowledge gained about the orebcdy configuration, defined constraints that were previously not fully appreciated. These constraints, and others, combined with objectives, were considered together to develop a new mining method. No single technique was found to be suitable, so a hybrid mining system was developed. A combination of ramping, cut and fill, and vertical crater retreat, with an option to use top heading and benching was developed. To complement the mining system, the type of equipment needed was decided upoun. Also, to support the mining system at this expanded rate of product ion, major modifications of existing infrastructure were required. THE EL MOCHITO MINE The El Mochito Mine, of Rosario Resources Corporation, has been in continuous product ion since 198. The mine began operations in April of that yeas at a rate of 100 tpd. The reserves in 198 were 100,000 tons of silver ore assayed at 1,250 grams per tonne. As of the end of 1979, the El Mochito orebodies have produced over 5.6 million tonnes of ore averaging 516 grams per tonne silver, 6.8 lead, and 7.8% zinc. Present ore reserves are about 7.9 million tonnes, averaging 138 grams per tonne silver, 4.6% lead, and 8.7% zinc, with minor quantities of copper, cadmium and gold. An expansion plan to increase mill production two fold to 2,500 tonnes per day is underway. This expansion will require the mine to produce 3,000 tpd. The mine consists of numerous orebodies, all of which have been mined to a certain extent. Of all the orebodies, the San Juan contains 8% of known reserves. This amounts to about 6.7 million tonnes. The significance of the San Juan orebody to the future life of the El Mochito Mine is obvious. If the required mine production of 3,000 tpd is to be sustained, the San Juan must be the source of the majority of that production. Due to the mineability and overall logistics concerned with the other orebodies, the San Juan must be able to reach and maintain a production rate of 2,000 tpd by 1982. GEOLOGY OF THE SAN JUAN OREBODY The El Mochito Mine is a classic example of a chimney replacement deposit in limestone. Similar deposits axe found in Mexico, at the Naica, Providencia, and Santa Eulia Mines. The El Mochito Mine is located at the south- western end of the Sula Valley on the western edge of the Honduras Depression in the Central Cordillera and Central Highlands of Honduras in a setting of Mesozoic sediments. The orebodies occur in a structural basin developed between NNE trending normal faults and apparently hinged on the south end. Topographically, the Mochito Basin lies between the uplifted Santa Barbara mountain in the west and the Palmer Ridge on the east. The San Juan orebody occurs near the intersection of the NE trending San Juan fault and the ENE trending Porvenir fault. The downward continuation of the orebody is controlled by the westward rake of these NW and N dipping structures. The discovery of the San Juan orebody is attributed to analysis of structural evidence of known ore deposits by in-company geologists. The composition of the San Juan orebody is primarily garnet skarn, with local concentrations of hedenbergite and magnetite. The economically important sulfide mineralization consists of (in decreasing abundance), sphalerite , galena, pyrrhotite , and chalcopyrite. There is some indication that a Cu-Ag mineral such as tetrahedrite may also be present. The skarns were formed by replacement of the original limestone by hydrothermal water migrating upward roughly along the intersection between the Porvenir fault system and the San Juan fault system. Textural evidence suggests that the orebody is a composite of several pulses of hydrothermal activity which would explain, in pat, the great irregularity of the contacts and the large horizontal variation in mineralogy. A general pattern of skarn types can be seen in the orebody, partially accounting for the observed lateral variation in grades. This zonation is very generalized, and one or more zones may be missing in any given locality. The orebody is almost invaxiably surrounded by a 2 cm to 25 cm zone of bustamite skaxn with low values. The border skarn is usually

Jan 1, 1981

By Frank L. Nason

(New York meeting, February, 1912) IN the year 1904 an eminent Swedish geologist prepared a report on the iron-ore reserves of the world. His estimates follow: Countries. Tons. United States, 1,100,000,000 Great Britain, . 1,000,000,000 Germany, 2,200, 000, 000 Spain, 500,000,000 Russia and Finland, 1,500,000,000 France, 1.500, 000, 000 Sweden, . 1,000,000,000 Austria-Hungary, . 1,000,000,000 Other countries, 1,200,000,000 Total, . 10,000, 000, 000 The iron-ore allotted to the United States by the Swedish geologist is barely sufficient to last 20 years at the present rate of consumption. On the other hand (according to Edwin C. Eckel,1 from whom the above and following statistics are quoted), there is hardly need for worry on the part of our iron industries for the, next two centuries or more. Upon the basis of careful work by the U. S. Geological Survey, in which Mr. Eckel has taken an important part, the following estimates arc definitely, but by no means finally, given for the United States District. Tons. Lake Superior District, . . 1,500,000,000 to 2,000,000,000 Alabama, red hematite. . . 1,000,000,000 brown hematite, 725,000,000 Georgia, red hematite, 200,000,000 brown hematite, 125,000,000 Tennessee red hematite, . 6110,000,000 I brown hematite, 225,000,000 Virginia., red hematite, 50,000,000 brown hematite, 300,000,000 Total, . . 4,725,000,000 to :5,225,000,000

Jul 1, 1912

By G. W. Ostroot, S. Shryock

Cementing deep, high-temperature oil wells where static temperatures range from 350 to 400F has become routine in the part decade. In the United States there were 271 wells drilled deeper than 15,000 ft during 1963. Many of these wells had static temperatures higher than 400F. Bottom-hole static temperatures near 700F are now realities in the geother-mal (steam producing) wells of California's Salton Sea area. The detailed planning initiated prior to drilling the wells is discussed together with the methods, materials and equipment used in solving the cementing problems which are encountered. Data are also presented that lead to development of cementing compositions that provide adequate thickening time, do not retrogress in strength, and maintain low permeability under these extreme temperature conditions. Field data include the cementing programs used on eight relatively trouble-free geothermal steam wells in the Salton Sea area. INTRODUCTION Not too many years ago cementing oil wells with temperatures in the range of 300F caused considerable anxiety. In some areas of the United States it is now fairly common to cement wells having bottom-hole static temperatures in excess of 400F. We are now confronted with the problem of cementing wells with temperatures ranging from 500 to 700F. Temperatures in this order of magnitude are often found in geothermal steam wells. From where does this extreme heat emanate? There are many theories as to the source of this steam flow. The most widely held views are: (1) heat- ing of ground water fairly close to the surface by an intrusive mass of hot rock; (2) steam generation from a reservoir of metamorphic rock, normally found below 25,000 ft and not at the shallower depths of the Salton Sea reservoir; and (3) high-temperature gases (water vapor) escaping and migrating from molten or semi-molten rock (magma) at a considerable depth. Of these. No. 3 seems to be the most generally acceptable explanation. Heat from springs and fumaroles has been used for years as a means of heating and cooking; however, significant progress in harnessing the vast power of underground steam reservoirs has been relatively slow. The first large-scale attempt to use the heat generated by steam from wells was made in Italy around the beginning of the 20th century. In excess of 250,000 kw of electrical power is now being produced from holes around Larde-rello, Italy. Another very active drilling program was initiated in the volcanic area of New Zealand in 1949.' Natural steam for power projects in the United States began in the early 1920's. An early commercial steam field is located at the Geysers, approximately 75 miles north of San Francisco, an area discovered in 1847 and used for many years as a health resort. Steam originates from 15 wells that have been drilled since 1957. The present output from this project is 25,000 kw. Success of the Geysers operation has been responsible for several companies taking a careful look at the feasibility of producing steam for power generation in the Salton Sea area of Southern California's Imperial Valley. Geothermal steam activity in this latter area began in 1961 when O'Neill, Ashmun and Hilliard completed Sportsman No. 1, at that time the hottest wellbore in the world.' Since its References given at end of paver. completion seven additional wells have been successfully completed in this area. Many problems encountered in drilling steam wells had to be overcome to make the ventures successful. Formation temperatures encountered in the Salton Sea seemed to be a straight-line function (a gradient of 13F per 100 ft of depth).' This imposed severe conditions on all aspects of drilling and completion. This varied, to some extent, from gradients in the older geothermal areas. Not to be overlooked is the effect of these temperatures on casing creep or elongation by thermal expansion (Table I), because standard API flanged wellhead equipment makes no provision for this kind of performance. Floating equipment was redesigned, and changes in types of downhole equipment were made in an effort to eliminate anticipated problems. In the later completed wells, standard oil-well cementing equipment has been used. During the early development of geothermal steam wells there were some problems resulting from blowouts. However, these were eliminated in the deeper Salton Sea wells and no problems were encountered with the drilling mud. A sodium surfactant mud was used on the Sportsman No. 1 to drill from 2,690 to total depth. Nevertheless, it was necessary that a cooling system be added and the mud cooled before circulating it back into the well. The difficulty in evaluating the size of the steam area and its potential in terms of pounds of steam and years of productivity still has not been resolved. Economic complexities have also entered into the steam play in the Salton Sea. The wells at the Geysers were drilled at a cost of $15,000 to $20,-000, whereas the Salton Sea wells will cost more than $150,000. This cost differential has to some extent been accounted for because of the heavily

Jan 1, 1965

By AIME

[Fig. 1], at left, is a corrected version of the first figure of the paper. Please note corrections in labeling of deposits.

Jan 1, 1973

By AIME AIME

The following acts of the Directors are reported for the information of members:¬ At a meeting held November 3, 1905, Messrs. Henri Le Chatelier, of Paris, France, and Andrew Carnegie, of New York, N. Y., having been nominated by a large number of members, and recommended by unanimous vote of the Council, were unanimously elected Honorary Members, in recognition of their distinguished services to the arts and professions represented by the Institute. At a meeting held February 7, 1,906, Dr. James Douglas, of New York, N. Y., having been" nominated by a large number of leading members, and recommended by unammous vote of the Council, was unanimously elected an Honorary Member, in recognition of his distinguished services to the practice and the literature of mining and metallurgy, his zealous and loyal devotion to this Institute, his fraternal generosity towards professional colleagues, and his effective advocacy, by public utterance and private example, of the free communication of technical knowledge and experience. At the same meeting, By-Law IV., which now authorizes the Secretary to appoint an '1 Assistant Editor," was amended by substituting the words, " Assistant with the title of Editor." At the same meeting, the resignation of Mr. Theodore Dwight, as Assistant Secretary and Assistant Treasurer of the Institute, was presented and accepted, and the Secretary was instructed to express to Mr. Dwight the thanks of the Board for his loyal and efficient services, and its regret that he could not continue in that position. . [SECRETARY'S NOTE.-Mr. Dwight's resignation, dictated solely by the demands of private business, covers only his immediate management of this office. He is still a Director and Councilor, and a representative of the Institute in matters connected with the new Carnegie Building, etc.-R. W. R.] At the same meeting, the Secretary and the Treasurer reported respectively their appointment of Mr. Henry WT. B. Howard as Assistant Secretary and Assistant Treasurer, to fill

Mar 1, 1906

By Charles R. Keyes

Discussion of the paper of Charles R. Keyes, Bi-Monthly Bulletin, No. 19, January, 1908, pp. 1 to 31. BERNARD MACDONALD, Guanajuato, Mexico (communication to the Secretary*) :-Mr. Keyes's paper is very interesting to me because of my personal experience with the development of the ore-deposits of Lake Valley. Seeing that many of the important facts connected with the early history of the development of these mines are either now unknown, or have become more or less distorted, and thinking that it would be interesting as well as valuable to have these recorded as a historical supplement to Mr. Keyes's elaborate paper, I present the following narrative: In February, 1881, soon after the Atchison, Topeka & Santa Fé railroad made connection with the Southern Pacific at Denting, N. M., the Lake Valley properties were brought to the attention of New York and Philadelphia capitalists by John A. Miller, of Silver City, N. M. At that time silver was $1.10 all ounce and silver-mining was very attractive. Vast fortunes were being made in Leadville and other Colorado camps, and Tombstone was pouring out its millions. Lake Valley, like all' other mining-camps in their early history, had its drawbacks, but the railroad, then passing within 14 miles of it, mitigated many of these. The camp lay in the foot-hills of the Black range, in which the Apaches had their stronghold, and raided, when it suited their convenience, the surrounding country, killing the prospectors and pioneer settlers and stealing their cattle. This band of Indians was joined by the outlaws and desperadoes from the frontiers of Texas, Arizona, and Mexico, who collectively defied the United States soldiers, restrained, as the latter were, by the mollycoddles from the East. The brutality of the Indian raids through Arizona and New Mexico in those days would scarcely be believed now, but they stain in deep

Feb 1, 1909

By Mäkinen, Eero

OUTOKUMPU, a large copper mine in eastern Finland, has the distinction of being one of the few important mines in the world discovered by a geologist the late Otto Triistedt, of the Geological Sur- vey of Finland, having found the out- clop in 1910 by tracing glacial ore boulders, some of which had been carried as far as fifty kilometres. As the mine had no connection with either railways or waterways and the possibilities of transport were poor, the owners first tried the Hybinette hydrometallurgical process to extract the copper. The raw ore was finely crushed, treated by a sulphatizing roast. and then leached. The resulting solution was electrolyzed, using lead anodes. This experimental plant, having a capacity of 10,000 tons (all Ions are metric tons in this paper) of raw ore and producing 300 to LEO0 tons of electrolytic copper annually, was built in 1913 and run until dis-

Jan 1, 1938

By W. A. Gibson, A. D. Trujillo

The Santa Rita copper deposit first served as a source of native copper for Indian implements and weapons. In 1801 Santa Rita copper, trans- ported by mule train to Chihuahua, began to be used commercially for making coins. It was a small- scale operation made difficult by Indian raids, transportation costs and depletion of the higher grade ores. There was, moreover, no known method for economically extracting copper from the under- lying low grade sulfide ores. Originally, copper and copper oxide ores were mined by underground methods, but there was virtually no development of the deposit-which became United States territory after the Treaty of Guadalupe Hidalgo in 1848-for almost a hundred years. A number of small underground mines had been started during that time, but it was not until 1873 that all the principal claims were consolidated under one control.

Jan 1, 1966

By T. W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (water box) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 % reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2012

By K. A. Natarajan, S. C. Riemer, I. Iwasaki

The relative significance of corrosive and erosive wear in magnetic taconite grinding is examined. The influence of different types of aeration (nitrogen, air, and oxygen) on ball wear was established for mild steel and high carbon low alloy steel balls. Ball wear data from dry and wet grinding tests are compared with those obtained in the presence of an organic solvent that does not promote electrochemical corrosion. Marked ball grinding tests and electrochemical measurements involving ball material and magnetite electrodes indicate that contribution from oxygen toward wear (corrosive wear) is relatively small, and abrasive wear appears to be significant. Rheological properties of the slurry appear to have an important bearing on the abrasive wear of grinding balls.

Jan 1, 1985