Search Documents

By Franklin H. Allison

The influence of cobalt and nickel on the properties of steel might be readily expected to be very similar. The two elements occupy close and somewhat unusual positions in the periodic table, their chemical behavior and compounds are so completely analogous and their various physical properties, including the ferro-magnetic characteristic, show such 3 remarkable correspondence, that there is no doubt of a strong resemblance existing between these two metals. However, the variety of properties that are obtained from steel is due largely to the fact that the element iron possesses allotropic forms. Alloying elements that affect these allot ropic forms, or alter the nature of the allotropic changes, exert a profound influence on the resulting steel. In the case of nickel and cobalt, although these elements are very similar chemically and physically, it is found that they differ distinctly in their individual effects on the critical points of iron. Both nickel and cobalt form a series of homogeneous solid solutions with iron at temperatures above 1500" F. The difference in their behavior does not occur until changes begin to take place in the solid state below this temperature. An inspection of the respective thermal equilibrium diagrams at the lower temperatures makes the opposite effects of nickel and cobalt clearly evident. Effect of Nickel and Cobalt in Binary Alloys with Iron The binary diagram of iron-nickel has been investigated by a number of workers. The lower temperature portion in Fig. 1 is reconstructed from the data of D. and H, Hanson.1 The diagram of iron-cobalt, shown in Fig. 2, is taken from the work of Ruer and Kaneko.2 Masumoto3 has recently discovered a lower critical point in cobalt and this has been added to the diagram. In both diagrams the space lattice structures as determined by Andrews4 have been included. It is interesting to note

Jan 1, 1927

By T. J. Koppenaal, M. E. Fine

The critical resolved shear stress of aCu-A1 single crystals has been investigated as a function of composition, testing temperature, and strain rate. The strength, and its temperature and strain rate dependency increase markedly with aluminum content. The solid solution strengthening at 4.2°K is much larger than at room temperature. The activation energy for the low temperature dislocation cutting process increases from about 0.17 ev for a 0.5 at. pct A1 alloy to about 0.50 ev for a 14 at. pct A1 alloy. This result is attributed to an increase in the width of extended dislocations due to the known decrease in the stacking fault energy. In addition, the activation volumes at 4.2 and 77°K decrease with aluminum additions. Concerning the solid solution strengthening in the 296° to 373°K range, no definite conclusions are reached, but it is suggested that subgrains and cutting of subgrains are important. In a previous paper,' the authors reported that adding aluminum to copper produces two types of strengthening: a yield point effect and an increase in the lower yield stress. This behavior is illustrated in Fig. 1 by shear stress-shear strain curves of furnace-cooled single crystals of pure copper and Cu-14 at. pct A1. The yield point effect, At, was thoroughly studied previously1 and shown to be associated with short-range order. The present paper reports an investigation of the lower-yield stress in aCu-A1 single crystals as a function of composition, testing temperature, and strain rate. EXPERIMENTAL PROCEDURE Single cryski1 tensile specimens were prepared in the same manner as previously described.l Briefly,

Jan 1, 1962

By T. F. Witherbee

(Read at the Amenia Meeting, October, 1878.) As the forms of blown-out furnaces are of much interest to iron-masters and metallurgists, the manner of taking the accompanying sections of the Cedar Point stack is here given. The diagrams show the original and also the final shape of the furnace after a two years and twelve days' blast, during which the following solid materials passed through it, viz.: Coal, 41,000 tons; ore, 57,000 tons ; limestone, 30,000; total, 128,000 gross tons. Product, 41 1/4 tons per day Bessemer pig iron. The apparatus used in taking the sections was a modification of that proposed by Mr. Frank Firmstone,* and consisted of a sliding rule, to follow around the circumference of the stack, which rule was connected by a string to a segment of a circle of 24 inches radius. The segment was carried by an arm which connected it to a hub as a centre, 2 inches in diameter. A second string was wound around the hub, and communicated motion to a pencil-carrier, the pencil of which marked out on paper the exact outline, and reduced it to a scale of 1/2 inch to the foot. The whole machine was made in about three hours, with the facilities of a carpenter's shop, and gave in operation every irregularity of the lining. The sections were taken at salient points, by lowering a hanging staging on which the apparatus was placed. Tracings from the paper of the machine were made, and, as in this case several copies were required, the tracings were glued on to thin sheets of basswood, and patterns carefully sawed out with a bracket saw. * Transactions, vol. iii, p. 106.

Jan 1, 1878

By William Ian Wark, Alwyn Birchmore Cox

DIFFERENT parts of the world in which mineral separation by flotation is practiced experience vastly different natural temperatures, and in some districts there is a big difference between summer and winter temperatures. It will be shown in this paper that the temperature is of considerable importance where it is desired to separate pyrite or arsenopyrite from other minerals. It is probable that some of the differences obtained in the flotation of these minerals at plants working under otherwise similar conditions are due to temperature variations. The influence of temperature on the flotation of galena, chalcopyrite and sphalerite by xanthates is less marked than its influence on pyrite flotation. EXPERIMENTAL METHOD The methods used have been described previously.1-4 In each test the clean mineral specimen was immersed in a solution prepared by adding the reagents in the following order: (1) sodium carbonate and hydrochloric acid as necessary to buffer the solution and to give approximately the pH value desired, (2) sodium cyanide, (3) copper sulphate, (4) ethyl xanthate, followed by (5) a final adjustment of pH value. After ½ hr. the mineral was tested for a xanthate film by bringing a bubble of air into apparent contact with the submerged polished surface. If true contact (spreading) was not obtained within ½ min. and after cleaning the surface by wiping with a small linen pad, it was concluded that the adsorption of a xanthate film had been prevented. Following the method already described (ref. 2), curves have been constructed such that for a solution ' composition corresponding to any point below the curve, contact between mineral and air is possible, whereas for a solution composition corresponding to any point above the curve, contact is impossible.

Jan 1, 1938

By Alwyn Birchmore Cox, Ian William Wark

Different parts of the world in which mineral separation by flotation is practiced experience vastly different natural temperatures, and in some districts there is a big difference between summer and winter temperatures. It will be shown in this paper that the temperature is of considerable importance where it is desired to separate pyrite or arsenopyrite from other minerals. It is probable that some of the differences obtained in the flotation of these minerals at plants working under otherwise similar conditions are due to temperature variations. The influence of temperature on the flotation of galena, chalcopyrite and sphalerite by xanthates is less marked than its influence on pyrite flotation. Experimental Method The methods used have been described previously.l-4 In each test the clean mineral specimen was immersed in a solution prepared by adding the reagents in the following order: (1) sodium carbonate and hydrochloric acid as necessary to buffer the solution and to give approximately the pH value desired, (2) sodium cyanide, (3) copper sulphate, (4) ethyl xanthate, followed by (5) a final adjustment of pH value. After ½ hr. the mineral was tested for a xanthate film by bringing a bubble of air into apparent contact with the submerged polished surface. If true contact (spreading) was not obtained within ½ min. and after cleaning the surface by wiping with a small linen pad, it was concluded that the adsorption of a xanthate film had been prevented. Following the method already described (ref. 2), curves have been constructed such that for a solution composition corresponding to any point below the curve, contact between mineral and air is possible, whereas for a solution composition corresponding to any point above the curve, contact is impossible.

Jan 1, 1939

By Ian William Wark, Alwyn Birchmore Cox

Different parts of the world in which mineral separation by flotation is practiced experience vastly different natural temperatures, and in some districts there is a big difference between summer and winter temperatures. It will be shown in this paper that the temperature is of considerable importance where it is desired to separate pyrite or arsenopyrite from other minerals. It is probable that some of the differences obtained in the flotation of these minerals at plants working under otherwise similar conditions are due to temperature variations. The influence of temperature on the flotation of galena, chalcopyrite and sphalerite by xanthates is less marked than its influence on pyrite flotation. Experimental Method The methods used have been described previously.l-4 In each test the clean mineral specimen was immersed in a solution prepared by adding the reagents in the following order: (1) sodium carbonate and hydrochloric acid as necessary to buffer the solution and to give approximately the pH value desired, (2) sodium cyanide, (3) copper sulphate, (4) ethyl xanthate, followed by (5) a final adjustment of pH value. After ½ hr. the mineral was tested for a xanthate film by bringing a bubble of air into apparent contact with the submerged polished surface. If true contact (spreading) was not obtained within ½ min. and after cleaning the surface by wiping with a small linen pad, it was concluded that the adsorption of a xanthate film had been prevented. Following the method already described (ref. 2), curves have been constructed such that for a solution composition corresponding to any point below the curve, contact between mineral and air is possible, whereas for a solution composition corresponding to any point above the curve, contact is impossible.

Jan 1, 1939

By H. J. Rose

SIXTY-FIVE million net tons of coal were carbonized in the by-product and beehive coke ovens1 of the United States during 1924. This tonnage represented 13.4 per cent. of the bituminous coal which was mined in that year. Table 1 shows production and disposition.2 TABLE 1.-Production and Disposition of Oven Coke in 1924 BY-PRODUCT BEEHIVE TOTAL Coal charged into ovens, tons 49,061,339 15,914,310 64,975,649 Coke produced (exclusive of screenings and breeze), tons 33,983,568 10,286;037 44,269,605 Average yield of coke, per cent 69.3 61.6 68.1 Disposition of coke: PER PER PER CENT. CENT. CENT. Blast furnace 82.5 82.8 82.6 Foundry 4.6 13.3 6.6 Domestic 8.3 1.4 6.7 Water gas manufacture and all other uses 4.6 2.5 4.1 Cokes having somewhat different combinations of chemical and physical properties are desired for the various uses listed above, and these properties depend primarily upon the types of coal used. American coals have a wide range of purity and coking quality, and the chief subject of this paper will be the selection of coals for the manufacture of blast furnace, foundry, domestic, and water-gas coke, in by-product coke ovens. It will obviously be necessary to include a discussion of those physical and chemical characteristics that are generally considered essential or desirable for each type of coke.

Jan 7, 1926

By Charles M. Means

A thoroughly modern coal-handling system has been installed at the Pittsburgh Terminal H. H. &. Coal Co.'s new No. 8 shaft, or Cover-dale mine, about 11 mi. (17.7 km.) from Pittsburgh on a spur of the Montour R. R. The Pittsburgh scam, which is the one worked, is reached at a depth of 342 ft. (104 m.). Power is delivered to the mine at 22,000 volts over a transmission line of the bow-arrow type of construction. A private telephone line connecting the various mines and the main office in Pittsburgh is carried on the same poles. The high-tension line is brought to an outdoor, step-down, transformer substation, where three 833-kv.-a., single-phase, 60-cycle, oil-insulated, self-cooled transformers reduce the potential to 2300 volts. The transformers are protected by electrolytic, aluminum-cell lightning arresters, horn gaps, and choke coils. High and low-tension busses, together with fuses, choke coils and air-break horn-gap switches with thcir remote-control operating mechanism are mounted on a substantial structural-steel tower 25 ft. (7.6 m.) in height. Mine Substation The transformer substation is adjacent to a. pressed-brick building that houses direct-current substation equipment together with switchboards, etc., for the control and distribution of power. This building also contains the hoist for the men and supplies. Main Switchboard The 2300-volt circuit is carried underground in a conduit from the transformer substation to an oil switch in the substation and supply hoist building. This is the main switch controlling the 2300-volt busbars mounted back to a twelve-panel black-slate switchboard. From the switchboard, 2300-volt circuits are carried to transformers feeding the street and house lighting systems and to other transformers furnishing power for the elevator and lighting circuits in the store building. Other 2300-volt circuits run from this switchboard to the main hoist building, fan house and auxiliary or man-and-supply hoist. High-tension wiring,

Jan 1, 1922

By H. P. Allen

THE chloridizing mill of the Standard Reduction Co. is located about 75 miles south of Salt Lake City on the Tintic branch of the Denver & Rio Grande Western R. R. and 12 miles from the Tintic Standard mine. The daily capacity is 200 tons of a siliceous, low-grade, silver-lead ore from this property. It has operated continuously since it was started in January, 1921. The process consists essentially of a chloridizing roast followed by a percolating leach with a nearly saturated solution of common salt, acidified with sulfuric acid, the precipitation of silver on sponge copper and of copper and lead on tin-plate cuttings. The precipitates are shipped to a smelter. Some of the general ideas involved are said to have been used by Augustin in England, in 1840. A number of textbooks treat of the subject, especially the chloridizing roast followed by a leach with sodium hyposulfite or amalgamation. The process was revived in this district by Theo. P. Holt, N. C. Christensen, the Bureau of Mines, and others.

Jan 8, 1925

By M. Baeyertr

Since 1915 many papers and books have covered industrial applications of X-rays from various angles. Two of the more recent are a paper by Fink and Archer, which describes in detail the technique of radiography, and a paper by Clark2, which embraces the whole field of X-ray metallogmphy. This paper, therefore, is confined to work of the X-ray Laboratory of the Western Electric Co., which naturally divides into two categories: radiography and diffraction patterns of various types. Radiography Radiography is the field in which the application of X-rays has had most general appeal among the industries which produce or use metals and alloys. Equipment permitting the examination of heavy sections of metals less permeable than aluminum or other light alloys requires apparatus capable of generating hard X-rays over a considerable period of time. The equipment used in the work presented in this paper is practically identical with that described by Fink and Archer in their paper on radiography in industry and is easily capable of penetrating 1/8 in. of lead. Radiography is used in two major groups of problems: (1) in the development of cquipment and tools and (2) in studies of materials. So far there has been no instance in which the use of radiography for routine inspection is justified. This is partly due to the fact that the manufacture of telephone apparatus involves the production of many identical parts by standardized procedures and equipment that has had development and trial before being put on a regular production basis. It is during this stage of development of equipment and tools that radiography has been used to particular advantage.

Jan 1, 1931

By T. S. Spice, H. L. Lovell, R. W. Utley

With the increased demand for lightweight aggregate, such materials have been manufactured from slags, clays, slates and, to a minor extent, the refuse of coal preparation processes. The latter source is attractive due to current interest in eliminating air pollution and improving the unsightly appearance of refuse piles as well as potential economic advantages, if a satisfactory product can be manufactured. A study has been made relating the composition of coal refuse, expressed as washability data, and the properties of a resulting aggregate. Three different refuse samples (bituminous and anthracite) were separated at gravities ranging from 1.4 to 2.96. Their chemical composition was determined. Aggregates were prepared in the laboratory from these fractions before and after ashing, at temperatures between 1250' and 1350°C. The specific gravity, expansion and compressive strength of the products were measured. The response of the refuse to bloat is related to the chemical composition of the ash to yield a glass of desirable viscosity and to the presence of a material which will form a gas in the appropriate temperature range. Carbonaceous material within the particle is a negative factor since after the glassy phase forms, oxygen cannot enter the mass thus inhibiting bloating. Precombustion of the refuse is also detrimental since it removes substances of gas-forming capability. The fraction sinking at 2.60 yielded an aggregate which had the lowest specific gravity, greatest expansion and greatest compressive strength. The purpose of this study was to seek and evaluate possible relationships between the composition of coal refuse, as expressed by washability data and factors affecting the production of a lightweight aggregate from refuse by bloating. The study was related to an intense program in the Department of Mineral Preparation at the Pennsyl- vania State University to study the possible elimination of air pollution from coal refuse fires by producing a low-carbon secondary refuse. Another phase of this program is considering possible uses of such a secondary refuse. Thus one study was to determine if a lightweight aggregate could be produced from this new refuse material and what effect the nature of refuse beneficiation would have upon the characteristics of a commercial aggregate product. It was hoped that these studies would assist in the design of a process and in establishing the optimum specific gravities at which refuse separation could be made in respect to the production of a low grade fuel from the float product and a raw material for lightweight aggregate from the sink product. The combination of producing a saleable low grade fuel and a lightweight aggregate, while at the same time minimizing disposal costs and air pollution contributions would be attractive to the coal mining industry. MECHANISM OF BLOATING Austin, Nunes and Sullivan,1 Ehlers,3 Everhart, 4 Riley7 and others, have stated that bloating is an expansion process in which two essential conditions exist simultaneously. These are: the development of a glassy phase over a relatively wide temperature range (the viscosity of this glassy phase plays a major role in the retention of the evolved gases) and the evolution of gases (SO2, SO3, CO2 and O2) from mineral decomposition in sufficient quantities at appropriate temperatures to form a cellular structure in the mass. Unless these two "type" reactions take place at the same time or in overlapping ranges of time and temperature, cellulation will not occur. In this event, the gas will escape or the melt will be too fluid to retain it; or if retained, the cells may be too large or the walls too thin for good strength in the product. The stages that occur when clays and shales are heated in an oxidizing atmosphere may be summarized as follows: 1) Drying and removal of free water to 200°C. 2) Absorbed water dehydration period (200 to 480°C). 3) Chemically-combined water dehydration period (480 to 700°C).

Jan 1, 1965

H. H. Campbell, Steelton, Pa. (communication to the Secretary) : I wish to thank Mr. Webster for the copious quotations he has made from my writings, as he has given nearly all the arguments I wish to advance. It is necessary to note, however, his statement that most of his experiments were made on universal-mill plates, and that these were not subject to my condemnation of irregularity. I think this is a mistake. It is well known that universal-mill plates are finished under very different conditions of temperature, with the express purpose of regulating the tensile strength. This is a perfectly legitimate practice; but it renders almost worthless any calculations on the relations of the chemical and physical equations when the influence of such finishing is omitted. Another important point Mr. Webster has not answered at all. I have shown by an excerpt from his own table that two entirely different formulæ may be constructed; and it is undeniable that one is as valid as the other, since Mr. Webster started with no premise at all save an assumption that the effect of carbon was constant. This was an assumption pure and simple, and hence has no special virtue. The whole result of Mr. Webster's investigation is not that the effect of carbon is a constant, and that those of phosphorus and manganese are variables. On the contrary, there are two answers, with nothing to show which is right. We learn that if carbon is a constant, then phosphorus and manganese are variables; but that if phosphorus and manganese are constants, then carbon is a variable. This is a distinct advance over complete ignorance, but it is not final and satisfactory from either a mathematical or metallurgical standpoint. Regarding my own formulæ, I would say that they are used regularly in the testing-laboratories of the Pennsylvania Steel Company. The tensile strength of every heat is calculated

Jan 1, 1899

By O. F. Thornton, D. L. Marshall

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,' although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.' wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By D. L. Marshall, O. F. Thornton

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,' although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.' wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By H. S. Martin

ALTHOUGH it was known some years ago at the- Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65¬mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. EARLIEST USE op MICROSCOPIC EXAMINATION OF TAILINGS As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for micro-scopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral particles or grains may be classified into separate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain no other included sulfides; 2. Grains in which all three of the copper sulfides are represented (the core may he of chalcopyrite, partially altered to bornite, these two minerals being entirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite.

Jan 1, 1929

By E. W. Mehal, R. H. Cox

A planar Gunn oscillator was developed for use in a monolithic microwave integrated circuit. The device was designed to operate in the frequency range of 20 to 30 GHz with a continuous wave output. Selective epitaxial deposition was used to form the n+n-n+ device structure in (111)-B semi-insuluting GaAs. The active n- region was about 5 µ thick and was doped to about 2 x 1015 electrons per cu cm by the reactor background. The mobility was -5000 sq cm v-1 sec-1. The n+ epitaxial deposits were doped to 1 x 10" electrons per cu cm using S2Cl2. Planarity of the three DURING the past few years, new microwave devices in discrete form have been developed utilizing GaAs. The next logical step is to combine these devices in a successive deposits was quite good; total overgrowth was less than 1 µ. Metal ohmic contacts were applied to the n+ or n- regions using a Ag-In-Ge alloy. The n+n-n+ devices had symmetric IV characteristics and could be operated C. W. for both directions of device bias. Metal ohmic contacts made directly to the n-region always Produced asymmetric devices. C. W. operation was obtained over the 22 to 28 GHz frequency range. The best performance obtained was 1.5 mw C. LV. output at 28 GHz. microwave integrated circuit. A potential application would be a radar receiver operating in the millimeter wavelength region. The key component in such an integrated circuit is a microwave oscillator, recently described by Gunn.1, 2 Under the influence of a large electric field, high-resistivity GaAs exhibits a bulk negative resistance, and high-frequency current oscillations result. Since relatively high voltage and

Jan 1, 1969

By E. Hoek

INTRODUCTION Rock slope stability research has been in progress for the past four years at the Royal School of Mines in London under the sponsorship of a consortium of 23 companies* with interests in open pit mining. This paper reviews the principal aims and achievements of this research project. In order to assist the reader in following these details, the basic philosophy underlying the formulation and direction of this research project is discussed. DISTRIBUTION OF RESPONSIBILITY In open pit mining, the economic necessity of keeping waste rock removal to a minimum generally means that the mine slopes have to be excavated to the steepest possible slope angle. On the other hand, excessive steepening of these slopes can induce failures, which may negate the economic benefits that have been aimed at and which may also result in loss of life and damage to equipment. Consequently, where slope failures are likely to prove to be a problem, an evaluation of the stability of the slopes to be created should be included as part of the overall pit design. How is the stability of a rock slope evaluated? When this question was examined, during discussions on the research policy to be followed at the Royal School of Mines, it was clear that relatively few satisfactory techniques were available in a form that would be comprehensible and therefore useful to the practical mining engineer. It was recognised that the research project must be directed towards two distinct aims: a) The evaluation of existing techniques for rock slope stability analysis and the provision of new techniques where these existing methods were found to be inadequate and b) The presentation of the results of this evaluation and research in a form that would be useful to engineers without specialist training in rock mechanics. It was soon realized that a university based research team, however large and efficient, could not achieve these aims without the co-operation and assistance of mining engineers,

Jan 1, 1972

The manpower and time involved in primary blasthole stemming at Kennecott Copper Corp.'s Bingham Canyon mine have been reduced considerable through the use of a mobile stemming machine invented y three mine employees. The patented machine, developed 2% years ago at an estimated cost of $5000 for two units, is the brainchild of Thomas R. Carlson, mine plant superintendent; Alvin J. McIntosh, drilling and blasting engineer; and Jay K. Buehler, field repair general foreman. According to McIntosh, the machine has been well received by the mine employees, who have been relieved of the tedious task of hand shoveling drill cuttings into the blastholes. It is estimated that the stemming machine has saved the mine approximately $25,000 per year in overtime and regular labor costs.

Jan 12, 1976

From 1917 to 1926 mining at the Climax Molybdenum Co. property was confined to the Leal and White levels at elevations of 12,145 and 11,935 ft respectively and to surface outcrops above the Leal level. At present the production is coming from the Phillipson and Storke levels at elevations of 11,465 and 11,168 ft. Until 1926 when B. S. Butler recognized the relationship existing between the orebody and a central core of fine-grained hydrothermal quartz, the orebody was believed to be tabular in form. The orebody lies within the pre-Cambrian granites and schists and another rock type designated as the Climax porphyry and surrounds a highly silicious core, the mineable portion of which varies in thickness from 250 to 400 ft.

Aug 1, 1955

By Milton Glicken

THE airborne geophysicist is a busy man these days. In his plane he may have the airborne magnetometer, the airborne scintillation counter, and the airborne electromagnetic surveying system. Each of these is an independent tool, but all require additional auxiliary equipment for locating the aircraft in space: recording altimeters and Shoran or aerial cameras. Now there is still another piece of equipment, the airborne magnetic gradiometer, an accessory to the magnetometer. To understand its uses, consider the function of the magnetometer itself. Aside from detecting magnetic ore, the airborne magnetometer finds greatest use in spotting intrusions of igneous material. Where there is enough contrast in magnetic susceptibility of igneous rock and adjacent formations, it outlines the intrusion. Certain minerals also influence the magnetometer directly, but with the exception of magnetite and possibly one or two others, their effect is weak and can be detected only when there is sufficient ore and the magnetometer flight passes very close to it. An igneous intrusion of infinite depth with vertical sides is represented on a magnetometer record by an anomaly, as in Fig. 1. Amplitude of the high depends on susceptibility contrast of the igneous rock. Generally speaking, the edge of the intrusion lies below the point of inflection of the curve, and this point, where the curvature changes from positive to negative on the magnetometer profile, would be near A in Fig. 1, with a counterpart, of course, on the other side. Location of the contact is one of the principal objects of the survey, but finding the precise point is not always easy, as inspection of the curve near A will show. Mineralization is often found at the contact zones, as at B. Magnetic effects, if detected, may be small, as in B', and when superimposed on the anomaly due to the instrusion they are very difficult to discern and analyze. Furthermore, if these small fluctuations are to be perceived by the magnetometer the vertical scale should be large. This increases the slopes of the anomaly and makes detection of small deviations and inflection points even more difficult. The airborne magnetic gradiometer was designed to help overcome these difficulties. What it presents is the first derivative of the magnetometer record with respect to time, that is to say, the slope at any point. Fig. 2 represents an actual magnetometer record (solid line) with the corresponding gradiometer record (dashed line) superimposed. Both records read from right to left. Vertical lines on the original magnetometer record are automatic steps designed to keep the pen from going off scale. The slope of any curve is greatest at the point of inflection or point where the curvature changes sign, and this point is a maximum (or minimum) on the gradi- ometer. The chief advantage of the gradiometer is that maxima or minima are much easier to see and to locate precisely; hence an accurate location for the point of inflection can easily be found. Note that points C and D are more sharply defined than C and D'. Similarly the small fluctuations of the original record, so important to the interpreter, are far more clearly shown at E, F, and G, than on the original record at E', F', and G'. Though not necessarily highs and lows on the gradiometer, they do show up clearly what would take a painstaking analysis to detect on the original magnetometer record. Will the gradiometer have a particular configuration which indicates an orebody? Not necessarily. The total intensity curve, or original magnetometer record, can display an orebody in various ways, depending on dimensions, orientation, latitude, and composition, as well as on direction, flight height, and instrumental sensitivity of the traverse. Where the total intensity can take on so many different shapes the gradiometer must vary too. It is generally recognized that interpretation of total intensity magnetometer records requires an expert analysis; the gradiometer can be of considerable assistance to the expert but it does not replace him. Mechanism of the gradiometer is simple. A Leeds & Northrup recorder in the aircraft records the magnetic gradient simultaneously with the total intensity, which is on another recorder. Fiducial marks are put on both records simultaneously and the speed of the paper through the recorders is kept the same on both. This makes it possible to place one record over the other for direct comparison. In the laboratory the flights are positioned on a map. Maximum and minimum points on the gradiometer, which can then be posted on the map at their proper locations, may be expected to fall along a trend crossing the direction of flight. Trends should indicate the edge of an intrusion, or some other important features, and when superimposed on the total intensity contour map help greatly to locate the points of inflection, or line of zero curvature.

Jan 1, 1956