Search Documents

By Pirooz Barar

The new Stanley Hall building will house the center for bio-engineering and technology research for the UC Berkeley campus. The structure is located at the northeast part of campus, adjacent to Donner Lab, on the west side of Galey Road, approximately 600 ft. from the Hayward Fault. The building site has a complex geological formation. To the east there are clayey soil shale formations, and to the west there is greywake shattered sandstone. The water table is at 10 ft. below grade. The structure will consist of 6 levels below grade and 8 levels above grade, which calls for an 83 ft. deep excavation on the northeast side. There is an approximately 35 ft. grade differential between the east and west sides of the building. Because of this severe grade differential, as well as high water tables, the lateral forces on the building due to uneven earth pressures would have been 2 times the magnitude of the seismic forces. To mitigate the lateral earth pressures, a permanent Soil Nailed Wall, integrated with the structural system of the building was designed. PB&A, Inc.?s in-house design program ?Winslope? was utilized to design the system and the data obtained from a rigorous monitoring program, were used to calibrate several computer runs using Plaxis program.

Jan 1, 2004

By Paul J. Lewis

Replacement of the Monroe Street Viaduct in southwest Baltimore City, Maryland included transforming 240 feet of the south approach from a pile-supported multi-span bridge to a mechanically stabilized earth (MSE) embankment supported by vibro-concrete columns (VCCs) and a load transfer platform. The project area was underlain with highly compressible soils which would have resulted in up to 18 inches of settlement under the proposed embankment load. Adjacent structures and critical underground utilities would have been impacteded or damaged by this settlement. Various load transfer alternatives were evaluated to mitigate the anticipated settlement by supporting the embankment on a deeper, more competent stratum. The alternatives considered included compaction grout columns, stone columns, deep soil mixing, and VCCs. Deep soil mixing was eventually selected for design, however, as part of a value engineering proposal, the general contractor Joseph B. Fay Company, with assistance from Hayward Baker and the Collin Group, prepared and submitted an alternative consisting of VCCs. This paper presents the details of the value load transfer platform and VCC design. Loading tests were utilized to confirm the VCC capacity and field changes were implemented based on the test results.

Jan 1, 2007

By J. K. Mitchell

Soil improvement is examined within the context of the characteristics of different soil types, the types of ground improvement techniques that can be used to improve them, and the level of improvements that might be achieved. Several case histories are described to show how the particular soil and foundation characteristics influence the choice and success of different ground improvement techniques. Although the basic methods for soil improvement have been known for many centuries, there have been significant recent advances in the technology for their use. Time effects following the densification of cohesionless soils may lead to significant improvements in strength and stiffness. Unanticipated chemical reactions may follow stabilization using admixtures when soils for which there has been little prior experience are encountered. In some cases foundations that combine features of both ground improvement and deep foundation systems may provide good performance at reasonable cost.

Jan 1, 2010

By Jim Cook

Arsenal Football Club required the development of a new home stadium in north London, subsequently named the Emirates Stadium. The proposed development comprised a 60,000 seat stadium, with associated facilities and a sports training centre. Described are the foundation solutions and piling construction techniques used, which take into consideration the potential impacts on existing above and below ground railway infrastructure and underground water structures. Methods used by the piling contractor to improve aspects associated with health, safety and quality are also described.

Jan 1, 2008

By Ali Porbaha

In today's fast-track construction environment, owners are searching for non-conventional technologies to build their projects faster and safer while maintaining traffic flow during construction. To that end designers and contractors are providing solutions that incorporate many unique features to expedite construction processes. In addition to timely delivery of the finished highway products, there is an increasing interest in making the initial investment in applying innovative technologies and thereby minimizing costly maintenance of highway projects. Accordingly, the aim of this paper (along with the accompanying paper) is to examine innovative technologies, developed mostly in Europe, that accelerate construction of highway, runway and railway embankment foundations. For each technology, a basic concept, installation technique(s), and design considerations are discussed, along with the case history of a real-world project. The Geotextile Encased Columns (GEC), AuGeo, and Continuous Flight Auger (CFA) are presented in Part I. Deep Mixing (DM), Cut-Mix-Injection (FMI), Mass stabilization, and Combined soil Stabilization with Vertical columns (CSV) technologies are discussed in Part II.

Jan 1, 2002

By Silvana B. Foá

Results from full-scale loading tests showed the use of the dynamic increasing energy test (DIET) to verify the capacity of deep foundations. This method allows the measurement of dynamic resistance - displacement curve and the prediction of the static resistance -displacement curve of the pile-soil system. The comparison between the use of DIET versus the static load test is also considered herein. This work was divided in two different phases, the first accomplished in Salvador (Bahia) and the second in Brasilia (Federal District), both in Brazil. The first phase consisted of field loading tests carried out on piles comprised by an approximate 10 to 12 meters thick deposit of fine saturated sand, overlying a stiff clay layer, which is found in certain areas of the Brazilian Northeast. Two metallic (rail track) piles were field loaded in this site. One of them was dynamically tested and the other was statically tested. The second site belongs to the Post Graduate Program of the University of Brasilia. It is comprised by an approximate 8 to 14 meter think deposit of porous clay, overlying a hard strata of saprolitic state. In this site a unique precast driven centrifuged pile was tested. The DIET procedure has demonstrated to be a tool of fast execution and low cost (if compared to static load test). It is a promising procedure to evaluate the behavior of pile-soil system.

Jan 1, 2002

By Robert J. Carle

This paper reviews a variety of highway structures which have been built using steel sheet piling as the permanent structural elements of bridge piers, abutments and wingwalls. Those structures built over the past 20 years in Europe include major highway bridges over railroads, highways and waterways in both urban and rural locations. Most highway structures built in the United States using steel sheet piling have been limited to secondary roads in rural locations. The main thrust of this paper is the presentation of various design concepts for highway structures which utilize steel sheet piling. The main purpose is to challenge the profession to move forward from this conceptual presentation and to develop the details necessary to provide safe, cost-effective structures which go well beyond the scope of those being built in the United States today.

Jan 1, 1989

By Alan Christopherson

Nearshore construction projects often require installation of steel piles and specific methodologies of installing piles may adversely affect nearby species of concern. Water is an uncompressible medium which allows for easy transmission of energy through the water column. Energy transmission through water depends on the following factors for pile driving: 1) direct contact of the pile and the water; 2) the depth of the water column; 3) the size of the pile; 4) type of hammer; and 5) the energy of the hammer. Seasonal restrictions are usually the best practicable alternative for reducing habitat impacts when pile driving activities may adversely affect the species of concern. When seasonal restrictions are not practical other options need to be evaluated, including mitigation and noise attenuation devices. The broad array of mitigation options will not be discussed as part of this presentation but instead will focus on noise attenuation technologies. Dewatered cofferdams can be effective noise attenuators as they eliminate direct contact of the pile with water while driving. Also, introduction of a compressible medium, like air, near the energy source can provide sound energy attenuation. An unconfined bubble curtain is relatively inexpensive but is not effective in tidal marine projects or rivers and may have unacceptable secondary effects. Secondary effects must be evaluated as these can increase exponentially for larger projects. Secondary effects to the environment include air quality degradation from air compressor use, transportation costs for fuel and equipment, and the potential for injecting oily compressed air into the water column. The confined bubble curtain works well in nearly all environments. It usually is more expensive initially, relative to an unconfined air curtain, but there is less potential for harmful secondary effects. Generally, seasonal restrictions will be adequate to protect species of concern. However, there are conditions in which mitigation or one of the sound attenuation options should be utilized. Site specific factors, including the amount of energy being imparted into the environment, sensitivity of the species of concern, current, accessibility, length of time needed to complete the project, and the cost of the sound attenuation, should be factored into the permit evaluation.

Jan 1, 2013

By Douglas L. Scaggs

Driving piles in under water applications has become more common place over the past twenty years. Where only a water depth reachable with a follower or dewatered cofferdam was the rule in the past, newer technologies developed for the offshore oil and gas industry have made depths of even several thousand feet possible offering new possibilities in foundation design and installation. With the new technology, engineers can now more efficiently design structures by placing foundations optimally thereby reducing weight and cost of the overall structure.

Jan 1, 2013

By Ruth McKeown, Gilson de F. N. Gitirana, Murray Fredlund, HaiHua Lu

The current design standards for the use of anchors in slopes is based on two-dimensional (2D) limit equilibrium analyses. Anchors are considered as discrete loads and the 2D anchor, factored based on the spacing distance, corresponds to extending anchors indefinitely in the third dimension. A three-dimensional (3D) analysis offers a more realistic representation of the problem, including the true discrete nature of the anchor point loads. This paper explores the typical differences between analyzing anchors in 2D and 3D, using four typical conceptual models. Slopes with constant cross sections were shown to be adequately represented by the traditional 2D approach. The maximum difference between 2D and 3D models was 21% and becomes negligible for lower anchor spacing values, as expected. A slope with an external load was analyzed to evaluate critical slip surfaces with lower aspect ratios. Slip surfaces with lower aspect ratios presented higher edge effects that contributed to the stability of the slope. The results indicate that optimum design requires the 3D evaluation of field conditions inducing low aspect ratios, such as concave and convex surfaces, weak layers, and external loads. INTRODUCTION Slopes may be stabilized using a variety of solutions, including anchors. When performing an analysis, geotechnical engineers often follow the traditional two-dimensional (2D), Limit Equilibrium Method (LEM). It is important to understand the consequences and limitations of the assumptions on which the 2D LEM is based. There are numerous studies on anchors that show the importance of considering the actual three-dimensional field conditions. Desai et al. (1986) proposed a three-dimensional procedure based on the Finite Element Method and considering elastoplastic behavior and interface elements, to account for stress and displacement distributions, the relative motion between the anchors and the soil mass, and nonlinear soil behavior. Several important stabilization mechanisms were explained. The role of grout injection was evaluated in terms of the produced normal stresses along the anchor-soil bounding surface. The approach was shown to reproduce adequately experimental tests on a sand, proving realistic stress distributions around the anchor. Nonlinear soil behavior influenced to a large extend relative interface motions. Michalowski (1989) applied an upper-bound limit analysis in 3D to slope stability analyses. Anchors were not specifically considered in this study, but the consideration of locally loaded conditions shed light on important modeling aspects. The manner how the slide mechanism becomes three- dimensional as the slope is locally loaded was demonstrated. This emphasizes the fact that anchors should produce field conditions that require 3D analysis approaches.

Jan 1, 2019

By J. W. Slatter

Cast in situ screw piling techniques (both displacement and non displacement) have seen considerable growth in recent years due to competitive production rates, low noise and vibration free installation. However the discussion on the mechanics of auger installation, which has implications on the installation effects and installation forces of screw piling augers, has been almost exclusively targeted towards non displacement techniques and in particular continuous flight augers (CFA). This paper discusses the historical development of the understanding of screw piling auger mechanics in sands and presents a new theoretical model to predict the soil transport and displacement characteristics of both displacement and non displacement augers with variable geometry.

Jan 1, 2000

By Larry D. Olson

Research, hardware development, and field testing have been conducted on systems to allow easy and accurate determination of both foundation tip depth as well as the properties of the soils at and above the foundation tip. The nondestructive testing method used for tip depth determination is the Parallel Seismic (PS) method, while the soil properties are determined by a Cone Penetrometer Test (CPT). The research and development effort reported herein uses a novel combination of the two methods to allow a single piece of portable field equipment to perform both tests. A system has been developed and tested that includes a triaxial geophone and a hydrophone in the cone probe tip to allow collection of the PS data by a CPT rig without requiring a drill rig with hollow stem augers. Using the instrumented tip along with a standard instrumented CPT cone allows for the simultaneous determination of both the depth of unknown foundations and the measurement of soil properties along the length of the unknown foundation. The combined system allows for a more complete and accurate analysis of foundation capacity and scour susceptibility.

Jan 1, 2007

By Clifford J. Wren

A geotechnical foundation solution was required to halt and prevent further structural distress suffered by a residential four storey apartment building in Hamilton, Scotland. Residents of the ten year old building started to notice cracking and signs of distress approximately one year after moving into the property. A detailed intrusive inspection of the structure revealed that the building was moving and had suffered significant settlement and structural distress at the shared party wall between it and an adjoining building. Roger Bullivant Limited (RBL) was appointed Principal Contractor to carry out an agreed remedial works contract which included a complete structural ?strip-out? of the ground floor, underpinning, contiguous bored pile retaining wall and reinstatement. The paper describes how a proprietary pile and needle beam underpinning system was used to prevent further differential movement and provide a new secure foundation for the residential building. The case study illustrates how a flexible problem solving approach can be applied to a difficult and sensitive geotechnical project.

Jan 1, 2008

By Douglas L. Scaggs

Over the past several years, pile foundations have grown to meet the demands of larger and heavier structures. As the foundations have grown, so has the need for larger and more robust piles to carry the increased loads. Seismic considerations have also required larger and tougher piles to withstand the added component of supporting structures during earthquakes. While H-piles, precast concrete piles, timber piles and small pipe piles have been the product of choice, many applications are now calling for much larger piling requiring larger equipment and presenting the contractor with new challenges. This paper is not intended to be a ?how to? guide as much as a discussion on the potential pitfalls a contractor should watch out for when considering a project where mega piles are required.

Jan 1, 2013

By Cau T. Bui

Thanks to Doi-moi (renovation) policy, many great bridges were constructed in Vietnam to meet demands of her booming economy in the recent decade and deep foundation structures were the only alternatives for the foundations of these great bridges. The deep foundation structures were constructed by modern technologies and almost of all these deep foundation structures were designed by foreign companies and carried out by Vietnamese workers and engineers under supervision of foreign experts. Beside successes, there were several failure cases in which the collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation killing 54 workers and seriously injuring 80 other workers was the most serious. This paper introduces construction techniques of the deep foundation structures applied to building of great bridges in Vietnam recently. It will especially focus on two failure cases: 1) collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation and 2) failure of drilled shaft foundation of Thanh-tri bridge due to poor construction technique and management. These two failure cases were greatly concerned by both bridge specialists and the public. Reasons of and lessons from these two failure cases will be carefully discussed. From the two failure cases, this paper will draw some lessons that should be important issues to be seriously paid attention when designing and constructing deep foundations in Vietnam.

Jan 1, 2008

By Matthew C. Pierson

Due to space limitations for transportation projects, many times sound walls must be constructed above mechanically stabilized earth (MSE) walls. These sound walls must resist lateral loads from wind or impact and must therefore be constructed on drilled shafts passing through the reinforced fill for the MSE Wall. Current design methods for the drilled shafts are believed to be overly conservative. Full scale lateral load testing of three foot diameter shafts contained within and solely supported by a 20 foot tall MSE block wall was conducted and the lateral capacity was evaluated. Shafts were tested individually and as a group. The data collected from full scale testing was then used to calibrate numerical models. This paper contains a discussion of how the facing type and stiffness affects the behavior of the numerical model as well as selected comparisons between the actual test data and selected model simulation results.

Jan 1, 2009

By Narong Thasnanipan

Performance of diameter 1.5 m toe-grouted bored pile founded at depth 44 m in sand-gravel formation of Chiang Mai City is presented in this paper. Toe grouting was applied by using tube-a-manchette method. Effectiveness of toe grouting was observed from the standard penetration tests conducted immediately below pile toe through grouting pipes at two stages, prior to grouting and three weeks after completion of grouting. Improvement of pile end resistance by toe-grouting is demonstrated with a series of back analyses carried out by load-transfer method employing hyperbolic transfer function. Construction experience of large diameter deep-seated bored piles in multi-layered subsoil and practical aspects of toe-grouting are also briefly discussed.

Jan 1, 2002

By Roberto Nova

The selection of the Osterberg Cell (O-Cell) technology as the standard testing method for deep foundations of the Railways Po Viaduct in Northern Italy offered a relevant number of field measures on large bored pile behaviour in alluvial soils. The assessment of pile response during such ?non standard? testing procedure was performed through the comparison with standard top load tests on companion piles as well as by numerical models of the tests including a simplified pile-soil interaction scheme. As shown in this paper, the O-Cell technology allowed a careful assessment of the non-linear pile behaviour even at quite small loading levels as those required by a posteriori proof tests on production piles. Simple numerical models proved to be very effective in the simulation and the interpretation of pile behaviour during such unconventional testing procedure.

Jan 1, 2008

By Gary L. Seider

Chance, a Division of Hubbell Power Systems, Inc., in conjunction with Sailors Engineering, Inc. has updated its Helical Design Capacity Software. This latest version, ?HeliCAP® v2.0?, is a state-of-the-art helical anchor and pile capacity program designed to operate in the Microsoft® environment. The program calculates the tension and compression capacity along with the frictional capacity, if applicable, of CHANCE® Civil Construction helical anchors and piles using design theories and methods adopted by Chance. This paper details the current state of practice employed by the software in the design methods and installation methodologies of helical anchors and piles.

Jan 1, 2007

By Peter J. Nicholson

Recognition of the liquefaction susceptibility of dam embankments has been heightened since the San Fernando Dam near failure incident in 1971. Both the downstream and upstream slopes of dams can be at risk for slope failure that can lead to breaching of the dam during or after a seismic event. Many dams have been remediated by various means such as the installation of stone columns or by excavation and replacement of the liquefaction susceptible material. Recent engineering and technology advances in equipment and materials has shown that construction of shear walls to the appropriate depths and at the right center to center spacing may be an economical alternative to the more traditional methods. Recently, the downstream embankments of at least 4 dams, from South Carolina to California, have been, or in the process of being remediated by the use of shear walls. The method of installation has been either multi-axis Cement Deep Soil Mixing walls or walls constructed by the use of trench excavation under self-hardening slurry. Four case histories of dam remediation are discussed, three by multi-axis paddle auger CDSM equipment one with the use of self hardening slurry trenches.

Jan 1, 2008