Search Documents

By Robert L. Martin, Brian W. Stump, David P. Anderson, David Gross

In an attempt to better understand the impact that large mining shots will have on verifying compliance with the international, worldwide, Comprehensive Test Ban Treaty (CTBT, no nuclear explosion tests), a series of seismic and videographic experiments has been conducted during the past two years at the Black Thunder Coal Mine. Personnel from the mine and Los Alamos National Laboratory have cooperated closely to design and perform experiments to produce results with mutual benefit to both organizations. This paper will summarize our activities, highlighting the unique results of each.

Jan 1, 1997

By U Nyberg

Peak particle velocity (PPV) and distance measurements from a single-charge blast test conducted by Swedish researchers in iron ore at the Kiruna Mine in northern Sweden are presented. They are used along with theoretical PPVs calculated using an equation based on hydrodynamics to determine a damage distance range caused by a single charge. This equation, which relates PPV to explosive properties, charge geometry, and distance from a charge, was then applied to a charge of different geometry that was used in drift rounds. A comparison between calculated and measured PPVs suggests that the stoping holes likely damage the easer hole locations, and the easer holes produce damage to the perimeter hole locations. The practical effect is that typical damage limit predictions based on measurements conducted in fresh or undamaged rock are conservative. This suggests that even when perimeter control is not exercised in drifting (i.e., the perimeter holes are fully loaded), the resulting damage may be less than normally expected due to the wave damping effect of the pre-damaged rock. Due to the damping effect, poor perimeter blasting practices are somewhat self correcting. However, it must be strongly emphasized that well-engineered blast designs with perimeter control are highly beneficial in relation to both economic and safety aspects.

Jan 1, 2011

By P D. Katsabanis, K Steeves, D Dombrowski

Accurate electronic detonators with firing time accuracy within 100 microseconds of the nominal have been used to control blast results in terms of fragmentation, vibrations and wall control. Axisymmetric experiments and experiments utilizing small benches have been conducted in order to calibrate a numerical model under development and examine the influence of delay interval on wall control, fragmentation and vibrations. The results obtained so far indicate definite advantages of precise timing in reducing back break and wall damage. Fragmentation is affected by the delay interval and high speed film observations and measurements indicate that the delay interval should allow the damage zone from each blasthole to be fully established prior to the detonation of the next borehole. Studies on vibration control demonstrated that vibration synthesis work using signature shots can only be of use if accurate delays are employed.

Jan 1, 1995

By Alan Minchinton, Ian Kirby, Jim Chan

It has long been known that successful blasting in soft and hard rock can require the use of different explosives. While choosing an explosive of the right energy density is important, the dynamics associated with non-ideal detonation behaviour play an equally major role. Tuning the energy release rate of an explosive to optimise its blast efficiency can be likened to tuning an internal combustion engine to improve its performance.

Jan 1, 2014

By Thomas A. Simpson, Yung-Kwaun Jow, Dennis L. Gamble

Construction of the $200 million Riverchase Galleria Mall in Hoover, Alabama was started in early 1984. The construction area consists of about 70 acres. The extensive building complex requires heavy concrete foundations which have to be poured during the early stages of construction and on a nearly daily situation so that contractual agreements can be met on a timely basis.

Jan 1, 1985

By Chuck Kliche, Bill Clements

This paper relates some of the experiences, good and bad, of blasting adjacent to residences of the primary author during his 15+ years of field blasting in the Northern Great Plains region. During this highly-rewarding blasting career, the author has become aware of two major issues in residential blasting: 1) What we call “Risk/Reward Ratio.”Some questions that must be asked by the blaster prior to taking on any blasting job include: - Can we eliminate or minimize the risk? - Is the reward worth the risk? - Do I have a measure of “nervous confidence” about the shot? 2) Public Relations. Two key elements to public relations are: - Notification - Education All the education in the world to the adjacent populous of what’s happening, of blasting in general, or of what to expect from the blasting does little good without notification. Good public relations is a key to controlling the cost of liability in a litigious society.

Jan 1, 2009

By Yoshihiro Moriyama, Toshihiro Okitsu, Ryouichi Banno

The fracturing composition using the gas pressure generated by the thermit decomposition reaction gives the following performances.

Jan 1, 1995

By Jaak J. K Daemen, Clayton R. Morlock

A study was performed to evaluate the predictability of airblast overpressures induces by production mine blasting. Thirty-seven production blasts were monitored using 3 blasting seismographs giving over 100 blast overpressure records. Blasts were monitored at 5 coal highwall operations and at a limestone quarry, all in the midwest. Blasts consisting of small surface charges were monitored to permit an assessment of prediction methods under controlled conditions, as well as to observe actual delay intervals and their influence on the overpressure.

Jan 1, 1983

By Charles L. Greening

MARTIN MARIETTA CEMENT at Martinsburg, West Virginia, has been and presently is engaged in coupling present open pit with old underground workings. Various drilling and blasting techniques have been introduced in an endeavor to achieve optimum results. This paper will relate to three roof shots at Martinsburg, one of which realized a controlled blast of 248,000 tons of material.

Jan 1, 1982

By Michael K. Phang, Thomas A. Simpson

Field studies at an underground mine site were conducted to evaluate and monitor blast-induced vibrations on an underground coal mine roof. The vibration data were evaluated so that a suitable damage criteria or guidelines from which a safe operating distance between surface blasting and underground mine operations can be established.

Jan 1, 1984

By Leslie Taylor, Uli Leiste

In this paper, results from small scale testing conducted to determine pressure time profi les acting on a plate (taken to represent the bottom of a vehicle) at any given distance from the center of the plate will be presented. These results will be discussed in relation to visual observations of the upward moving sand.

Jan 1, 2008

By W. Reisz

The fear of heights is a natural defense against performing a dangerous and unnatural act such as standing on the edge of a hundred foot wall. Yet through familiarity, a casual attitude often exists. Those of us, who work near highwalls on a daily basis, may become overly comfortable in our surroundings, losing sight of the disaster which may often rest a single misstep away. And this is where the hidden dangers lie.

Jan 1, 2009

By Gary Anderson, J. P. Remi Proulx

Rio Tinto’s Colowyo Coal Mine produces 2.1 million tons per year in northwest Colorado. Colowyo uses the terrace mining method to recover up to seven coal seams ranging in thickness from 5 to 20 feet. Coal recovery in the 6 foot thick high grade C-seam has recently been challenged due to large variations in the pitch and roll of the seam. As well, some coal damage was seen due to an increased thickness of the overburden consisting of a hard sandstone channel.

Jan 1, 2012

By Deepankar Das, Gulshan Kumar Sadhwani, Jyoti Prakash Sahoo

Sindesar Khurd Mine (SKM), the largest underground mine in the Hindustan Zinc Limited portfolio, is located approximately 60 kilometers (37 miles) north of Udaipur. In the 2018 financial year SKM achieved an annual ore production of 4.5 Mt (4.42 million LT) and mined metal production of 247 kt (243,099 LT).

Jan 1, 2019

By G Alan Foster

Many complaints generated from blasting operations result from the marked human response to ground transmitted vibrations and air blast effects and so many authorities have considered the regulation of blasting in terms of human response rather than, as previously, in terms of preventing damage to structures.

Jan 1, 1981

By Donald H. Matthews

The usual method of dismantling massive concrete formations with explosives, is to totally demolish the entire concrete structure. If any portion of a concrete structure is required to remain in its original form and retain its structural integrity, the use of explosives is usually forbidden and the portion to be dismantled is demolished by mechanical means, using various techniques and equipment that are tedious and expensive.

Jan 1, 1978

By Y Omura

If dynamite is used in hot metal mines, it may be subject to decomposition, and the increase in nitroglycol vapour under the high temperatures causes bad headaches of workers. Also the explosives containing ammonium nitrate are very dangerous when mixed with sulfide ores at a high temperature!. Therefore we developed a heat-resistant water gel explosive which is safe to be handled at these hot metal mines.

Jan 1, 1983

By W C. Burkle

A rather common observation over the last several decades at least has been that rock or ore properties influence blasting results more than does the explosive type that has been used in the blast. It we accept that premise than it is held here that the material to be blasted should receive even closer attention as to its properties. Several years ago, Dr. Richard Ash published papers that pointed out the rock properties that mostly influence blasting. These principles are given attention in this paper. We have gone somewhat further - or lets say expanded this subject in regard to the role of rock structure in open pit blasting. Though open pit work is given some prominence, we believe that much can be observed and applied to underground mining.

Jan 1, 1979

By Thomas Leonard, Philip R. Berger, Bryan E. Papillon

Bardon Trimount Inc., a large producer of aggregate, crushed stone, and concrete, was experiencing significant public opposition to its five quarries in the Boston area. It was believed by the authors that this opposition could be significantly lessened if the total number of blasts per week were reduced. Although the blasting company at these quarries, Austin Powder Company, contended that this could easily and safely be accomplished by increasing the size of the blasts, regulations precluded this alternative by limiting the total amount of explosives that could be used per blast.

Jan 1, 1996

This paper describes the circuit simulations based on SPICE of the SDI Electronic Detonator System at the system level. SDI is launching the Electronic Detonator System with a robust serial protocol exhibiting great ease in field usability and deployment. Programmable delay time with increment of 1 ms up to 10s is possible. Bus length of up to 2 km containing 1600 detonators can be utilized. This system was analyzed using SPICE simulations and an Excel-based firing model spreadsheet. The effects of wire diameter, resistivity, detonator leakage characteristics, blasting array topology (lumped, linearly distributed or branched) were simulated using the firing model. Such spreadsheet is instrumental in determining the blasting topology of any given detonator number and bus wire diameter or resistivity. Initial simulation results were interactively coupled back into making the serial protocol more robust during typical mining conditions.

Jan 1, 2006