Search Documents

By R. L. Solmer

During 1959-61, the Bureau of Mines investigated the strain and deformation induced in rock and concrete linings around mine openings by retreat panel caving at the Climax Molybdenum mine. Two concrete-lined slusher drifts on the Phillipson level of the mine were instrumented with both electrical strain gages and extensometers. Changes in strain and deformation were recorded over an 18-month period during the undercutting and caving of the mining panel. General agreement was found between the strain and deformation measurements and the hypothesis that the vertical component of the stress field on the openings is almost completely removed by undercutting. This phenomenon is a possible explanation for the structural failures that occur in the slusher drifts during the undercutting cycle.

Jan 1, 1965

By Gilbert M. Farrior

The electrical resistivity the coefficient of electrical resistivity the Hall coefficient, and the absolute thermoelectric power were determined in this Bureau of Mines investigation for nine compositions of the TiB2-CrB2 sub-system. The numerical values of the electrical resistivity and the thermo-electric power were greater for the intermediate compositions than for the end members. The absolute values of the Hall coefficients and the coefficients of electrical resistivity were less for the intermediate compositions than for the end members. The electrical resistivities and Hall coefficients were about the order of magnitude of most metals--from 34 to 202 microhm-cm and from about 0 to -23.3 X 10-4 cuP/coulomb. The thermoelectric power was somewhat greater than that of most metals--up to 15.6 microvolts per 0 C.

Jan 1, 1965

By Harry M. Conger

Kaiser Steel Corporation's Eagle Mountain Mine is located in the Colorado Desert, 60 miles east of Indio, California. Concentrates from the mine are shipped by rail 164 miles to the company's steel mill at Fontana, and also to Longbeach, California for export. Temperatures are typical of the lower desert ranging from a high of 120 degrees in the summer to a low of 25 degrees in the winter. The average annual rainfall of about two inches comes mainly as cloud bursts during the summer months. From its inception, the Eagle Mountain Mine has had the problem of breaking its mine rock. Practices followed from 1949 until 1962 were very costly, did not produce uniformly good fragmentation, and were incapable of sustaining high production. During this period, every conventional type of explosive then in use was tried and found to be unsatisfactory for one reason or another. The first slurry test work at Eagle Mountain was started in 195E and finally by 1962, after having tried all the slurry mixtures then available including some "home made" formulas, a metallized slurry was perfected at the mine which overcame all of the disadvantages of former blasting methods.

Jan 1, 1965

By J. M. Kuchta

Experimental data are presented on the autoignition temperature (AIT) characteristics of the hydrocarbon jet fuel, JP-6, in various oxygen-nitrogen atmospheres under conditions of constant volume and constant pressure. AIT's of this fuel in air varied little with fuel injection pressure but increased greatly with decreasing fuel content at low fuel-air-ratios. They also increased with decreasing oxygen content of the fuel vapor-oxidant atmosphere. Consistent with thermal ignition theory, the ignition temperatures increased with decreasing initial pressure, ignition delay, and vessel radius; expressions are given which define the observed variation of AIT with these variables for JP-6 fuel vapor-air mixtures. The significance of autoignition temperature data obtained using various ignition criteria is discussed to show the usefulness of such data in evaluating fire and explosion hazards. In addition, data are presented on the extent of oxidation that occurs prior to autoignition of this fuel in air at various temperatures.

Jan 1, 1965

By R. E. Ogilvie, H. C. Gatos, R. E. Hanneman

The ejj-ect of high pressures on chemical inter-diffusion in the Fe-V system was determined by analyses of concentration vs distance profiles of atmospheric and high-pressure diffusion couples. Diffusion data were obtained as a function of tern -perature and composition. Activation energies, activation volumes, and frequency factors were determined at 1 atm, 20 kbars, and 40 kbars as a function concentration in the a and y phases. The A great deal of research has been carried out in the measurement and understanding of binary chemical inter diffusion in solids. Studies of the effects of high pressure on interdiffusion in binary systems, however, have been virtually nonexistent until the present work. This paper gives a detailed account of the effect of high pressure on interdiffusion and the Kirkendall effect in the Fe-V system. The present data are compared to existing theo- Kirkendall effects were measured at 1 atm and 40 kbars. At 1 atm Dy > DFe at the marker concentration; however, Dv approaches DFe under pressure, and at 40 kbars the values are approximately equal. The high-pressure and atmospheric diffusion data are evaluated on the basis of theoretical models. Chemical analyses of the diffusion -couple profiles were made using an electron microbeam probe. retical treatments of pressure dependence of diffusion which are based upon self-diffusion studies. THEORY The rates of atomic migration in metals and alloys are regulated by the repulsive forces exerted on an atom during its motion from one equilibrium lattice site to another and by the availability of a jump site. Application of high pressure is expected to decrease diffusion rates because it decreases interatomic distances as well as defect concentrations. A number of theoretical treatments have been focused on the problem of calculating self-diffusion coefficients in solids under atmospheric pressure. In general, the vacancy mechanism of diffusion appears to be dominant at high temperatures in most metallic systems. The migration of an atom by this

Jan 1, 1965

By M. R. Geer

Samples of coal from six beds in the Roslyn-Cle Elum field of Washington were subjected to float-and-sink tests to determine their amenability to the production of high-ash boiler fuel for on-site power generation. Grindability tests and analyses of ash were made. All of the coals would require some degree of cleaning to insure a product of 25 percent ash. With two of the coals the entire size range would have to be washed. With the other four, it would suffice to clean only the coarse coal and bypass the raw fines.

Jan 1, 1965

By P. S. Rudman

Laves phases, AB2, are considered as Izerrzisub-stitutional solutions m1hich are defined by a one-for-truo replacement scheme. Atomic-size tnisfit is considered in terms of deviations of the ratio 2V°b/V°A from unity, where v° = atomic volume. A simple elastic model has been used to calculated deviations from "Vegard&apos;s law of atomic vol-umes". Comparison has been made between calculated and observed atomic-volume deviations fov 222 Laves phases. Agreement is generally very good although there ave some few exceptions which appear to be excusable in terms of electronic changes that ore beyond the scope of the present model. We can consider the formation of a binary sub-stitutional solution A-B from an A solvent as one-for-one replacements of A atoms by B atoms. As the atomic-size ratio deviates from unity, the solution becomes thermodynamically less stable and hence more restricted because of atomic-misfit strain energy. In accordance with our previously presented conclusion1 that the atomic volume, v, is in general the most appropriate measure of atomic size, the ideal size ratio for a binary sub-stitutional solution is vg/vA = 1. The Laves phases have been described by Berry and Raynor2 in terms of various stacking sequences of hexagonal layers of B atoms for the three structures MgZn2(C14), MgCu2(C15), and MgNi2(C36). To form the Laves phase of ideal composition AB, we start with complete hexagonal layers of B atoms in the appropriate stacking sequence and we remove, according to an appropriate scheme for each structure, two out of every four B atoms and replace the two removed atoms by one A atom. We thus might expect to find that the ideal size ratio for the Laves phases is 2v/B/ VA= 1. From this point of view, then, we call Laves phases hemi-substitutional solutions since we employ one-for-two replacements. By analogy with substitutional solutions we can expect for Laves phases that as the ratio 2VB/Va deviates from unity the phase occurrence will be more restricted. Laves3 has plotted the distribution of Laves phases as a function of the radius ratio, ?A/rB, and found that, while the distribution extended from 1.05 < rA/B < 1.50, the

Jan 1, 1965

By A. G. Weber, H. J. Welge

A published calculation method for predicting incompressible, multidimensional fluid displacement has been adapted to the problems of water and gas coning in oil wells. Since depth and radial distance from the wellbore are the two key dimensions affecting the shape of a gas or water cone, coning calculations are well suited to the use of two-dimensional methods. The alternating direction implicit procedure (ADIP) was used for relaxation calculations of two-phase potentials in a two-dimensional grid. From the potentials and the capillary pressure relationship, saturation and pressure distributions were calculated which trace cone growth with time. Predictions have been made for well producing histories both before and after core breakthrough. To check validity of the method, two-dimensional calculations have matched the coning behavior and produced water-oil ratio history of a laboratory sand-packed model. They have also matched the coning behavior of several producing wells, for which the calculations were compared with produced water or gas cuts and logs showing water or gas cone movements. INTRODUCTION The application of two-phase, two-dimensional calculations using ADIP to various reservoir flow problems has been described in the literature.1-3 When adapted for computer solution, this method has proved to be a powerful tool for simulating well and reservoir behavior. This paper discusses the method as applied to well coning calculations. Single-well and coning calculations comprise an especially difficult class of two-dimensional problems which require special techniques for computer calculation and determination of reservoir characteristics. Refs. 4 through 8 describe previous approaches to the coning problem. Several examples of water and gas coning calculations, including studies on both laboratory models and producing wells, are presented here. The two-dimensional method accounts realistically for the most critical parameters affecting coning behavior, including production rate, formation stratification, horizontal and vertical permeabilities, depth of well penetration, gravity and capillary forces. The method considers the different densities and viscosities of the two phases and the relative permeability and capillary pressure characteristics of the rock and fluids. In addition to tracing cone growth in the vicinity of the wellbore, the method calculates the overall movement of the fluid interface throughout the well&apos;s drainage volume. Incompressible fluid flow is assumed to occur between the producing interval and the well&apos;s limit of drainage. Calculations can be made for the producing history both before and after cone breakthrough. A typical two-dimensional grid or array of blocks used to solve a coning problem contains about 400 blocks. The well&apos;s cylindrical drainage volume can be represented by about 20 radial subdivisions and the formation thickness by 20 vertical subdivisions. The grid spacing is normally smaller near the withdrawal interval to define the cone shape accurately. For this work we used an IBM 7074 digital computer having a core memory of 10,000 ten-digit words. A typical study, covering 5 to 10 years of well producing history, required from three to six hours of computing time. MATHEMATICAL SIMULATION OF CONING BEHAVIOR BASIC METHOD In coning calculations, the reservoir volume drained by the producing well is represented by a two-dimensional system of blocks as shown in Fig. 1 for water coning studies. The horizontal dimensions of the blocks increase with radial distance from the well axis in geometric progression, i.e., the block size is small near the wellbore and large near the well&apos;s drainage radius (re). Vertically, the blocks are bounded by horizontal planes located at different depths through the

Jan 1, 1965

By J. E. Harris

By elimination of other possible nucleation processes, it has been demonstrated, for commercially pure magnesium and a Mg-Al alloy, that at stresses less than that necessary for triple-point cracking creep cavities are most probably nucleated heterogeneously at second-phase particles. Evidence for the existence of such particles is presented and the role of grain boundary sliding in the nucleation process is examined quantitatively. DURING creep deformation of polycrystalline magnesium and its dilute alloys in the temperature range 0.45 to 0.7 Tm (Tm = absolute melting temperature) cavities form mainly along grain boundaries oriented normal to the stress axis and failure eventually occurs by their growth and impingement.&apos; The possibility of low-ductility creep failure of magnesium-alloy reactor cans during service has prompted a number of studies of cavity formation in these materials.2-5 In this paper divergent theories of cavity nucleation6-10 are examined critically and conclusions drawn regarding the most probable mechanism of formation of cavities in magnesium. The paper is divided into two parts. The first section consists of the review and quantitative assessment of the possible role of grain boundary sliding in the nucleation process. In the second part an experimental program is described where an electron-microscope technique has been used to determine if second-phase particles exist in as-received commercially pure magnesium and in a magnesium alloy 1) THEORETICAL REVIEW Possible nucleation sites for creep cavities are: a) high-angle grain boundary triple points,11-14 b) subboundary/grain boundary intersections,15-18 c) ledges in the grain boundary, 19-25 d) second-phase particles. 9,26-30 Each of these possibilities is now considered with special reference to deformation of magnesium. 1.1) Triple-Point Cracking. The stroh31 condition to nucleate fracture is: " > vr [1] where ss = applied shear stress, ? = surface energy, C = shear modulus, L = length of sliding interface. This relationship is independent of the nature of the interface and it is possible to calculate the stress concentration at the end of a sliding high-angle grain boundary and thus deduce, approximately,* the minimum applied stress necessary to nucleate triple-point cracking. Such theoretical predictions for Nimonic alloys have been made by McLean13 and found to agree quite closely with the minimum stress determined by experiment. Stresses capable of nucleating triple-point cracking should also be sufficient to nucleate fracture at a grain boundary due to intragranular slip, for the lengths of sliding interface in the two cases are approximately equal. Thus the minimum stress for triple-point cracking should represent a demarcation between failure due to general "cracking" and that due to cavitation. Hauser, Landon, and Dorn32 have demonstrated that for polycrystalline magnesium in the temperature range 78° to 298°K the fracture stress is inversely proportional to the square root of the mean grain diameter. As pointed out by stroh31 this result indicates that Eq. [I] describes the fracture characteristics of magnesium at low temperatures. Heal3 has reported that for rapid deformation (112 pct hr-1) of polycrystalline magnesium the transition from cracking to cavitation occurs in the temperature range 175" to 275°C. He also presented the fracture-stress values for the same material tested under similar conditions. From Eq. [I] taking G = 1.3 x 10" dynes , ? = 600 ergs . cm-2,33 and L = 0.017 cm, a Stroh-McLean13,31 tensile stress of -266 kg. cm-2 is calculated, corresponding to a transition temperature of -190°C; this is in

Jan 1, 1965

By Robert C. Johnson

Single crystal whiskers of ZrO2 and TiO2 were grown by solution and crystallization of these oxides in molten baths. Mixtures of Na2B407 and LiC1 were the most suitable growth media for zirconia. Sodium borate alone and Na2CO3 plus SiO2 were best suited for titania. The solubilities of zirconia and titania in molten sodium borate were determined, Whether zirconia whiskers were dendritic or nondendritic depended on the temperature used. The best single crystal whiskers were grown below 1,100° C. Titania whiskers always grew as single crystals. The tensile strengths of zirconia and titania whiskers were about 15,000 psi and 50,000 psi, respectively. Modulus of rupture was about 49,000 psi for zirconia whiskers and 75,000 psi for titania whiskers. Chemical analyses showed the zirconia and titania whiskers to be pure. The zirconia and titania whiskers were shown by X-ray analysis to be, respectively, baddeleyite and rutile.

Jan 1, 1965

Mr. O. F. Lewis opened the meeting at 9:00 a.m. lie announced that Stan Shuhart, had the following announcement. to make: Stan. Shubart: George Delamater of Fort, Lauderdale, Florida scads greetings to his friends here at the meeting. O. F. Lewis: Thank yon, Stan. This morning we will start our meeting by turning it over to a very distinguished gentleman. I&apos;m sure all of you know him. He started his work career many, many years ago, but lie doesn&apos;t look nearly this old, and his energy belies this. From 1.910 to 1916 he was a chemist with the American Smelting & Refining Co. at. Garfield, Utah. From 16 to &apos;17 he was a broker with J. A. Hogle Company at Salt Lake. From 1917 to 1948 he was a metallurgist, ore buyer, assistant manager and later general manager of the Utah department. ASRC at Salt Lake City; and also president of the Garfield Chemical Co. Since 1951 to the present. time he has been President and General Manager of the Independent Coal & Coke Co. and Vice President of the Western Rock Bit Co. He has held many, many honorary positions; former Chairman of the Board of Regents of the University of Utah, former President of the Salt Lake Winter Sports Association, Past President. of the Community Chest there, and is presently a Director of National Coal Association, a Director of the First Security Bank of Salt Lake City, Utah, and also a Director of the Hotel Utah.

Jan 1, 1965

By John G. Simmons

A tutorial account of the tunnel effect between metal electrodes separated by a thin insulating film is presented. Energy diagrams of metal-insulator -metal sandwiches are briefly discussed, and the isothermal and thermal J-V characteristics for symmetric and asymmetric tunnel junctions are derived from a generalized expression. Experimental data from tunnel junctions are presented, and it is shown how, correlation between theory and experiment permits a determination of some of the oxide properties. Finally, the barrier heights in AT-Al2O3-A1 junctions determined by various inr3estigators are discussed. The object of this paper is to give a tutorial account of the electric-tunnel effect between metal electrodes separated by a thin insulating film and to illustrate its utility in the study of metal-oxide interfaces. This paper will emphasize the theoretical aspects of the electric-tunnel effect: however, a brief account of the more recent experimental work will be presented. A more comprehensive experimental study of the tunnel effect will be presented in the following paper by Drs. Pollack and Morris, see p. 497. We will open with a discussion of the energy diagrams for metal-insulator-metal junctions and what we mean by the electric-tunnel effect. Following this is an account of the theoretical studies of Sommerfeld and Bethe, and Holm, and the recently reported calculations on symmetric and asymmetric junctions using the generalized formula. The theoretical presentation is concluded with calculations on the temperature dependence of the tunnel J-V characteristic. In the experimental section, it is shown how barrier heights and thicknesses are determined by comparing the experimental data with the theory. Finally, the results of various investigators on the determination of the barrier heights in Al-Al2O,-A1 systems are discussed. I) POTENTIAL BARRIERS BETWEEN CLOSELY SPACED ELECTRODES Since it is necessary to supply energy to a metal in order to observe electron emission from its surface, it is evident that the potential energy of an electron within a metal is lower than that of an electron at rest outside the metal. It follows, then, that the electron must undergo a change in potential as it crosses the metal-vacuum interface. In the Sommerfeld1 free-electron theory of metals it is assumed that the free electrons, the electrons responsible for the electrical characteristics of metals, move in a constant potential environment in the metal, and are contained within the metal by a potential barrier at the metal-vacuum interface. It will be evident that the idea of a constant potential environment is a very idealized model, since the potential energy of an electron is influenced by all of the atoms and the other electrons within the metal; however, its use is justified by the many excellent results it gives.2 Fig. l (a) is the energy diagram of the model envisaged by Sommerfeld; the metal is represented by a potential-energy well of depth V,; the vacuum level represents the energy of an electron at rest outside the metal. At 0°K the electrons, which exist in pairs in discrete energy levels, fill up the well to an energy ?, the Fermi level. The distance, Vo - ?, from the Fermi level to the vacuum level is known as the work function of the metal, and represents the minimum energy required to free electrons from the interior of the metal at 0°K.

Jan 1, 1965

By A. K. Mukherjee, J. E. Dorn, J. D. Mole

Investigations were carried out on the effect of polyslip on the strain hardening of aluminum single crystals. The orientations investigated were those lor which the tensile axis was in the [001], [111], [112], and [012] directions plus another for which the Schmid angles for {111}(110) slip were 1 deg. The experimental data were analyzed on a model based on the intersection of dislocations with particular emphasis on the effect of polyslip on the activation volume for inter-section. It is shown that the rate of strain hardening inreases for those orientations wherein attractive dislocation intersections occur and that those orientations which produce the greater number of such intersections exhibit the greater strain hardening. Good correlation of the data is obtained with the concept that attractive junctions, as proposed by Saada, Play an important role in accounting for the rate of strain hardening. EXISTING concepts on the nature and cause of strain hardening in fcc metals have been deduced principally from experiments on the deformation of single crystals under single slip. The effect of crystal orientation on the shapes of the stress-strain curves for single slip have been summarized by seegerl and more recently by Clarebrough and Hargreaves.2 Tensile specimens whose axes fall near the center of the [001]-[011] line of the standard triangle of the stereographic projection exhibit the longest range of easy glide (Stage I) and the lowest rates of linear hardening (Stage 11) whereas specimens whose axes lie near fie [001]-[111] line of the standard triangle have limited or no easy-glide range and exhibit somewhat higher linear strain-hardening rates. Specimens whose axes lie near the [001] or the [ill] poles do not exhibit easy glide and have the highest rates of linear hardening. Kocks3 has shown that the highest rates of linear hardening Occur under Polyslip when the tensile axis coincides with the [111] or the [ 001] pole. Since the rate of strain hardening is sensitive to specimen orientation and the incidence of polyslip, these relationships might help to discriminate between various dislocation models for strain hardening in fcc metals. Previous attempts to analyze the effect of orientation on strain hardening,1"3 however, did not provide a unique answer to this problem. Consequently the present investigation was undertaken wherein additional data, particularly that for the effect of polyslip on the activation volume for intersection, was also determined in order to provide more complete information on the details of strain hardening. Whereas analyses of these data reveal that several recommended models for strain hardening are at variance with the facts, good correlation of the data is obtained with the concept that attractive junctions4 play an important role in accounting for the rate of strain hardening. I) EXPERIMENTAL APPROACH seegerl demonstrated that slip in fcc crystals at low temperatures is dependent on thermally activated intersection of glide dislocations with forest dislocations. This has been confirmed by tests on single crystals of aluminum by Mitra, Osborne and Dorn5 and on polycrystalline aluminum by Mitra and Darn.&apos; Thus in accord with Seeger&apos;s theory, the shear strain rate, ?, below a critical temperature, T, is where .V is the number of points of contact per unit volume between forest dislocations and glide dislocations, A is the area swept out per successful intersection, b is the Burgers vector, v is the frequency of vibration of the segment of the glide dislocation undertaking intersection, U is the activation energy for intersection, k is Boltzmann&apos;s constant, and T is the absolute temperature. For aluminum, which has an extremely high staeking-fault energy, the constriction energy is negligibly small and therefore the activation energy decreases practically linearly with the stress according to as will be recomfirmed later, where Uo is jog energy at the absolute zero, G and Go are the shear moduli at the test temperature T and O°K, respectively, L is the spacing of the forest dislocations, t is the applied shear stress for slip, and tGo is the stress field that must be surmounted athermally.

Jan 1, 1965

By John S. Berber

Tar produced as a byproduct from low-temperature carbonization of coal contains only small amounts of valuable lower boiling tar acids but relatively high percentages of high-boiling tar acids. These high-boiling tar acids are characterized by a high degree of alkylation and can be converted into the lower boiling homologs by catalytic treatment to remove the alkyl groups or decrease their chain lengths.

Jan 1, 1965

By J. H. Brophy, A. L. Prill, H. W. Hayden

An error lzas been found in the conventional way of determining the time exponent of linear shrinkage for the solution-precipitation stage of liquid-phase sintering. Large amounts of shrinkage due to initial rearrangenzent result in erroneously low exponents and tni si dentification of the rate-controlling process. Two alternative, mathematically correct, methods of calculation are applied to existing data on Fe-Cu, WC-Co, and Tic-Ni-Mo. This results in reidentifi-cation of the rate-controlling process and somewhat better agreement with related data. In each case the solution-precipitation process is solution-controlled and not diffusion-controlled. THE liquid-phase sintering process has been the object of a considerable amount of research for many years. Linear shrinkage vs time data at various sintering temperatures have been used recently in an attempt to identify the prevailing mass-transport processes in a number of metallic and nonmetallic systems. There is an analytical error inherent in the methods previously used for handling data during the "solution-precipitation" stage of shrinkage which must be recognized before the correct rate-controlling processes can be determined. It is the purpose of this paper to show how the error has affected previous conclusions and to suggest corrections. A number of mechanisms have been proposed to explain experimental observations during sintering in the presence of a liquid phase. The earliest of these is due to Price, Smithells, and williamsl who attributed the observed growth of the solid phase to the simultaneous solution of smaller particles and growth of larger particles. From the work of Lenel et al.2,3 and Gurland and Norton4 has come the suggestion that the liquid-phase sintering process may be divided for analysis into three steps: 1) rearrangement upon formation of the liquid phase; 2) solution and reprecipitation of the solid phase in the liquid; and 3) "coalescence" or a final stage of sintering, characteristically slower than the solution-precipitation process. The sequence of steps is shown schematically in Fig. 1. Kingery5 presented a thermodynamic and kinetic analysis of the first two "stages" of the liquid-phase sintering process in which the functional dependence of lineal shrink- age on time at temperature was used to identify the rate-controlling mass-transport process. Table I summarizes the time dependences and processes considered by Kingery.5 This method of data presentation has been employed by Kingery and coworkers for Fe-CU,6 WC-Co, and a number of nonmetallic systems," and bv Whalen and Humenik for Tic-Ni-Mo and Fe-cu.8 In each of these studies, the rate-controlling step during the "solution-precipitation" stage was identified from the slope of the curve in that stage on a logarithmic plot such as Fig. 1. However, in all of the previous studies, at a certain composition, relatively large amounts of shrinkage due to rearrangement preceded the solution-precipitation stage. Under these conditions, the larger the amount of rearrangement shrinkage the

Jan 1, 1965

By H. T. McAdams

Current theories of fracture maintain that brittle materials contain flaws or regions of weakness at which fracture originates. Whether a particular flaw grows depends upon the stress distribution in its vicinity and upon the presence of other stress relieving mechanisms capable of absorbing the applied energy. Under load, therefore, certain of these flaws will be activated, and the resulting fragments will have a size distribution determined by the spatial distribution of active flaws. Gaudin and Meloy,1 assuming a random occurrence of flaws, have derived the size distribution of fragments as

Jan 1, 1965

By R. C. Wilcox, R. V. Lawrence, P. A. Calhoun

The V-Rh-Si, Nb-Rh-Si, and Cr-Rh-Si systems were investigated to evaluate the extent of solid solubility between binary Cr3O structures. All Cr3O components lie within the favorable atomic size range1 for the formation of the Cr3O structure. Previous studies indicated complete solid solubility between V3Si and V3Sn2 and no solubility between Sn and cr3si3 or Si and Nb3Rh.4 The Cr3O structure is not found in the Cr-Sn and Nb-Si binary systems. Powder compacts were are-melted under argon, homogenized in a vacuum at 1000°C, and water-quenched. Alloys containing greater than 15 at. pet Si were annealed 100 hr. X-ray diffractometer methods were used to study all systems utilizing copper radiation for the Cr-Rh-Si system and chromium radiation for the other two systems. V-Rh-Si System. The alloys prepared in the V-Rh-Si system and the measured lattice parameters for the Cr3O structure found in each alloy are listed in Table I. The characteristic Cr3O diffraction pattern was found in all binary alloys. The measured lattice parameter of V3Rh (VRS-1) is in agreement with the reported value5 while the value for V3Si (VRS-5) is only in fair agreement.&apos; In

Jan 1, 1965

By E. R. Gilbert, D. E. Munson

Creep of copper under 75 to 1.50 kg per sq cm stresses at temperatures near the melting point was found to he a complex reaction controlled by three mechanisms acting in parallel. In order of appearance with decreasing temperature, the auerage activation energies, Qc , are 168, 79, and 24 kcal per mole. Stress dependence of the minimum creep rate was found to he an exponential for the two high-Qc processes and a power law for the low-Qc, process. Transition of control occurs from one mechanism to another. The relative transition temperature depends upon the applied stress, and the range oiler which the transition occurs depends upon the difference in the activation energies of the mechanisms. The creep behavior at high temperature is explained by the climb of dislocations through thermally or mechanically formed jogs, CREEP in pure fcc metals at temperatures in excess of one half the absolute melting point is normally controlled by dislocation c1imb.1,2 A climb model which seems applicable, according to an extensive analysis of data,3 was derived by Weert-man.4 This model assumes jog-saturated dislocations and predicts an activation energy, Qc, nearly equal to that for self-diffusion, USd. Although the requirement of jog saturation is restrictive, agreement between theory and experiment seems adequate. Many other theoretical treatments, including an early model by Mott,5 include detailed consideration of jog formation as an initial requirement for climb. These models predict activation energies for creep which differ from those of self-diffusion. Seeger6,7 postulates an observed activation energy related to the stacking-fault energy. Thus, Usd <Qc<5Usd + Uj where Uj is the jog-formation energy. Seeger incorporated qualitatively the influence of the relative numbers of thermal and athermal jogs. Expanding this concept, Shoeck8 explicitly states a function based on formation mode and relative numbers of vacancies: e r ci exp {-uf/k T} exp {-Um/k T} [ 1 ] where Uf and Um are energies of vacancy formation and migration, respectively. The concentration of jogs, Cj, depends upon the manner of jog production. For intersection jogs, Cj is not sensitive E. R. GILBERT, Junior Member AIME, formerly with De- to temperature; for thermal jogs, Cj is proportional to exp {—Uj /k T}. Schoeck regards each mode as a distinct mechanism; therefore, the mechanisms may act together.299 The diversity predicted by theory, surprisingly, has not been substantiated by experimental results. A significant investigation must include the extremes in stacking-fault energy. Extensive creep studies of aluminum10 and nickel,11,12 high stacking-fault energy metals, have been made. Comparable studies on a low stacking-fault energy metal, such as copper, have not. It is the purpose of this paper to report the results of an investigation of the creep of copper under conditions which favor thermal jogs. EXPERIMENTAL Cylindrical compression creep specimens (0.240 in. in diameter by 0.400 in. long) were machined from cold-drawn rods of electrolytic tough-pitch copper containing 0.0007 Mg, 0.002 Fe, 0.001 Ni, 0.0005 Ag, Cd < 0.005, and Pb < 0.005 wt pct impurities. Undetected spectrographically was a nominal 0.04 wt pct 0, which occurs as a Cu2O constituent distributed discontinuously at grain boundaries. Vacuum annealing at 900°C for 15 min produced a stable 0.03-mm average grain diameter. Testing was carried out using apparatus similar to that described by sherby,13 modified by enclosing platens and a push rod in a vacuum cylinder. Normally this arrangement resulted in pressures less than 10 Only a slight surface tarnish, less than 0.0005 in. in thickness, occurred during the test. The applied stress, corrected for atmospheric pressure, was maintained within 2 pct of the desired true stress by the addition of lead shot at fixed strain increments. Creep strain was measured with dial gages as a relative displacement of the upper and lower platens; accuracy of measurement was 0.0001 in. Two creep-test methods were used, the differential or cyclic temperature14 and the isothermal, to obtain creep data at stress levels of 150, 100, and 75 kg per sq cm over the temperature range of 620° to 1032°C. Minimum creep rates were used from both test methods; this was considered proper because comparable temperature tests or cycling to the same temperature gave the same creep rate, within experimental error. The cold vacuum test chamber, with the unstressed specimen in place, was heated to temperature by placing a preheated furnace over the chamber. Temperature equilibrium was attained within 30 min. For the cyclic tests, the stress was removed during the 5 to 10 min necessary to effect the temperature change and re-

Jan 1, 1965

By J. B. Moritz

From the beginning, man has concerned himself with the task of controlling the elements and forces about him so as to provide a better and easier life. In the accomplishment of this task, he is required to utilize in the best way possible the resources which are available to him. In many cases, the available resources must bee refined before they are in a useable form. Many products in the mining industry fall into this category, as some form of refinement is generally needed to produce a saleable product. Over the years man developed more efficient ways of extracting the resources from earth through the use of electrical and mechanical devices. A reduction in manual labor, which is a by-product of increased efficiency through machines, has also been enjoyed. The combination of man&apos;s senses and new devices has also enabled man to reach a high level of control in the refinement process. Control of a process through machinery and man&apos;s senses has been termed an "art." Until recently man&apos;s senses (sight, feel) were the only method available for making measurements simply because suitable measurement devices (instruments) were not available. Even today some items cannot be measured and man&apos;s senses must be used. However, the development in our instrument laboratories tends to indicate that time will eliminate this. In recent years, control of many processes has been reduced to a science and part or all of the art eliminated. This does not imply that process art should be degraded; however, when a process is reduced to a science, uniformity of the product from day to day is attained. Decreased processing time and more efficient use of additives and raw materials are other benefits that result from control of a process when it is reduced to a science.

Jan 1, 1965

Jan 1, 1965