Search Documents

By E. P. Williams

"Prince Edward Island, Canada's smallest Maritime Province, is located in the southwestern part of the Gulf of St. Lawrence. The Province is more or less centrally located in the Maritimes Basin, a large intermontane basin within the Appalachian orogenic belt. The Maritimes Basin is subdivided into sub-basins and uplifts which exhibit two dominant structural trends: east and northeast. The Basin is known to be petroliferous because of the seeps, shows, oil shales and albertite found in southern New Brunswick and northern Nova Scotia and the gas and oil produced from the Stony Creek field near Moncton, New Brunswick.Permian beds are exposed on the Island, mostly along sea-cliffs. A maximum thickness of about 5,000 feet of red beds -shales, sandstones and conglomerates -make up the sequence. Over most of the Island, the Permian section is much thinner. Four key wells (Mississippian tests) and several shallower tests have been drilled. The Pennsylvanian-Mississippian section thickens rapidly off the Port Hill Uplift at the northwest, where it is less than 4,600 feet thick, and continues to thicken to about 20,000 feet in the Cumberland Basin at the southeast. Geological and geophysical data combine to give us the structural picture of the deeper beds.Prospective reservoir rocks are primarily in the Missis-sippian Horton and Windsor groups. Prospects are:-1. on or over structural highs in the basement; 2. on anticlines or fault highs; 3. over or peripheral to salt domes or salt-core anticlines; 4. at truncation pinchouts of Mississippian prospective beds; 5. in basal sandstone or granite wash on the pre-Carboni-ferous basement; and 6. in facies traps at changes from sandstone to shale or porous to tight carbonate rocks."

Jan 1, 1967

By Donald M. Keagy

How many times have you said or heard someone say, 'What are you doing right now?" And how many times have you heard the reply, "Breathing air!" Probably never, or at most only a few times in a facetious vein. Breathing air is absolutely necessary to sustain human life, and yet most of us take it completely for granted. Beginning ten to fifteen years ago there was growing concern on the part of the general public that pollution of the air is a threat to man's health and welfare. Concurrently much thought and effort was devoted to the task of defining and resolving the problem of air pollution. In the course of this effort it has become quite clear that our National policy in this regard should be founded upon three basic axioms: (1) Action should not be postponed until emergency conditions make it compulsory; (2) The air cannot be purified after it is polluted, and (3) Air pollution control cannot be accomplished without close cooperation among all levels of government, industry, and the public.

Jan 1, 1967

By F. Habashi

Conclusive evidence is given showing that the dissolution of gold in cyanide solution follows mainly the over-all equation A similar equation can also be written for the dissolution of silver. Theoretical derivation of the velocity equation for this reaction has been obtained, which describes quantitatively the experimental facts. The equation is as follows: where [CN-] and [O2] = the concentrations (in moles/ml) of cyanide and dissolved oxygen, respectively. DcN- and Do2 = the diffusion coefficients of cyanide and dissolved oxygen; 1.83 x 10-5 and 2.76 x 10-5 cm2 sec-1, respectively. A = the surface area of the metal in contact with the aqueous phase, in cm S = the thickness of the boundary layer; varies between 2 and 9 x 10-3 cm, depending on the speed and method of agitation. Rate being expressed in g. equiv. sec-1. INTRODUCTION During recent years a number of papers have been published on the kinetics of dissolution of gold and silver in cyanide solution.1,6 The authors agree that the rate of dissolution is diffusion-controlled, but disagree regarding the mechanism of the reaction. Some authors'-3 support the Bodlander equations: The apparently conflicting results, when critically reviewed, are concordant and lead to the conclusion that the proper equation for the dissolution reaction should be only Eq. 1. This conclusion is based on the following facts: 1) For every 2.2 equivalents of metal dissolved one mole O2 was consumed. 2) For every 1 equivalent of metal dissolved, 2 moles of cyanide were consumed.' 3) Hydrogen peroxide is formed during the dissolution of gold or silver, and for every 2.2 equivalents of metal dissolved, one mole H2O2 was produced.1,2 The fact that Kudryk and Kellogg4 did not detect H2O2 during the dissolution of gold should not throw doubt on the many affirmative reports of other investigators. Lund2 has shown that depending on the crystalline nature of the silver surface, (e.g. method of etching the sample) H2O2 may undergo catalytic decomposition heterogeneously according to: Further Kudryk and Kellogg4 carried out their experiments in the presence of 0.5% KC1 to achieve a greater electrolytic conductivity, and Matsudaira7 has shown that H2O2 is catalytically decomposed (homogeneously) in the presence of C1- ion in alkaline solution. 4) Experiments carried out by Boonstra8 and Lund2 showed that the dissolution of gold and silver respectively in KCN + H2O2 in the absence of oxygen was a slow process. Thus the reaction takes place to a minor extent only. Further kinetic studies showed that: 1) The rate of dissolution depends on the surface area of the metal in contact with the liquid phase, thus indicating that the process of dissolution is a heterogeneous process. 2) The rate of dissolution depends on the speed of stirring,5,6 thus indicating that the process is controlled by a physical phenomenon.

Jan 1, 1967

By d&apos, Kathleen J. Amico

This summary appears in Minerals Yearbook volumes I-II, and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonweath of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The sections of this chapter and the area chapters in volume III contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1967

By E. G. King

The Bureau of Mines made experimental determinations of the heats of formation of forsterite and chrysotile at 298.15° K. The heat capacities of two polymorphs of serpentine, chrysotile and antigorite, were measured over the temperature range from 50° to 298° K and the entropies at 298.15° K were evaluated. The heat content of antigorite above 298.15° K was measured to 850° K. These thermochemical data were combined with other pertinent data to give heat and free energy of formation values at high temperatures. Free energy values are given for the reaction, forsterite + water = brucite + serpentine at different temperatures and pressures.

Jan 1, 1967

By D. E. Stephenson. Discussion by R. G. K. Morrison, L. Obert

R. G. K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que., Canada) - The discing of drill core has been a recognized pressure phenomenon for many years but only recently has an interest been taken in the mechanism involved. The work of Jaeger and Cook is referred to in the text. The authors have now advanced the study to establish, within certain loading limitations, a direct relationship between axial and radial stress at failure. This is an important contribution. In mines generally, where pressure conditions result in the spalling of openings, the faces of drifts and crosscuts, on scaling, usually show a concavity with respect to the opening very similar to the face of the drill hole after the separation of the stub. The same holds for shaft sinks. This suggests a similarity between the mechanism of the discing of core and that of the spalling of an opening, under pressure, to develop a more stable outline. The latter, commonly regarded as shear, is the most conspicuous type of failure observed in

Jan 1, 1967

By D. Bienstock

The use of alkalized alumina in removing sulfur dioxide from a coal-combustion flue gas at 625° F was investigated on a pilot plant scale. The absorber was 26 feet long and 1.6 inches ED. Counter-current gas-solids flow at gas velocities of 8 to 15 ft/sec in the presence and absence of baffles, as well as solids entrainment at gas velocities of 20 to 23 ft/sec with solids recycle, were employed. The spent absorbent as regenerated as fixed bed with the reducing gases--reformed natural .7.7d hydrogen. Of absorption-regeneration were successful completed using the alkalized alumina rolled into spherical granules 10 to 16 mesh. There was no loss in activity of absorbent toward SO2 with a modest attrition equivalent to 0.l percent of the solids feed. Supporting studies were conducted on the effect of the sodium content in the absorbent, the composition of the reducing gas, thermal treatment to increase absorbent hardness, and removal of absorbed chlorine from the absorbent. A mathematical model was formulated to describe the removal of SO2 by alkalized aluminum from fixed and falling beds.

Jan 1, 1967

By D. T. Peters, C. R. Cupp

Aging of commercial 18 pct Ni maraging steel and of related binary, ternary, and quaternary alloys has been studied by electrical resistivity, X-ray diffrac-tion, and hardness measurements. The aging process is in three stages: 1) recovery of martensite; 2) two precipitation reactions; 3) formation of nickel- rich austenite. The main objective of this work was to discover the nature of the Co-Mu interaction. Addition of cobalt to the Fe-18 pct Ni-5pct Mo alloy results in acceleration of the pvecipitation reaction by increasing the super-sat~lration 0f molybdenum. The cobalt-containing al- loys show no incubation period for the precipitation reaction, but the alloy without cobalt shows an initial slow reaction. These results are interpreted in terms of precipitation on dislocations. At low aging temperatures, the presence of cobalt leads to the appearance of a second type of precipitate which is a particularly effective hardener. Cobalt was found to retard the formation of austenite. Overaging is a combination of classical overaging and the formation of austenite in the structure. he- activation energy for the precipitation reaction determined from resistivity ,measurements is 42.8 kcal per mole and the growth of the precipitate is found to obey at law at high tenzperatures and a tU3 law at low temperatures. HE mechanism of strengthening of the 18 pct Ni maraging steels has been studied extensively since 1962.'-? The strengthening is due to precipitation hardening of the martensitic matrix. The main precipitate is an inter metallic compound involving molybdenum, but there is disagreement about its identity.

Jan 1, 1967

By George H. K. Schenck

Diminishing returns in management's fight to lower manufacturing expenses have added luster to savings that can be achieved in delivered costs through creative management of the distribution function. This is especially true for companies engaged in the production of bulk commodities, for which transport costs may represent 25 to 50% or more of total delivered price, A. E. Cascino, vice president of International Minerals and Chemical Corporation, recently gave an example of why top management in his firm is concerned with distribution: "The price of a ton of phosphate rock, f.o.b. mine, is about $7. The cost of warehousing, freight, and handling frequently totals an additional $11 . . . . If one of our competitors . . . discovers a way in which he can cut his distribution costs by $3, we're dead! Even if we wanted to offset our competitor's more efficient means of shipping with reduced f.o.b. price for our product-we don't have that much profit margin . . . ." In a special report on the revolution now occurring in transportation of goods, Business Week stated in its September 24 issue: "Moving and storing goods on their way from mine and mill through various sub-assemblies to their final markets costs anywhere from $50 billion to $75 billion a year- $100 billion if paperwork costs are included.

Jan 1, 1967

The variation of austenitic grain size with temperature for the steels XKSlSO and XK9261 was determined using the vacuum ctching technique.It is shown that the effect of temperature on the mean grain intercept is relatively small, up to approximately 950°C. Above this temperature the rate of increase of grain size rises sharply.Within the limits of the 1-4 hr vacuum etching times used the effect of time at temperature is relatively small on the ASTM grain size of the steels.

Jan 1, 1967

By Harry Perry

U. S. consumption of sulfur and sulfur products is expected to increase at a rate of 8 percent per year between now and 1980, largely as a result of their use in fertilizer markets. World consumption is also increasing rapidly, but at a-lower rate, about 6-percent per year. In 1965, sulfur recovered in the United States from purification of natural gas; nearly doubled from the 1956-1960 average; production from pyrites declined; and production of elemental sulfur increased 15 percent. Concern about air pollution resulting from sulfur oxides produced from the combustion of fossil fuel has lead to intensive research on methods of removal before combustion, during combustion (in-process methods), and from the resulting flue gases. If all the sulfur in fossill fuels were recovered, more sulfur products would be produced than were consumed in the United States in 1965. Removal of sulfur from coal before combustion could result in a product sufficiently-high in sulfur to be a suitable raw material for sulfuric acid manufacture. In-process methods produce solid sulfates, some of which may have commercial value. Flue gas removal' methods for sulfur oxidest generally result in the production of a byproduct either of sulfuric acid or sulfur. The projected sale of these materials significantly lowers the anticipated cost of sulfur dioxides pollution abatement. Alternate methods for sulfur dioxide reduction are discussed. The various proposed processes are described and costs are given for the various methods for which estimates have been made.

Jan 1, 1967

By W. A. Nagel, R. P. Alger, H. Sherman, J. Tittmann

A sidewall epithermal neutron tool has been developed to substantially reduce environmental effects that have previously complicated neutron log interpretation. Designed for operation in uncased wells, the device provides increased accuracy in both liquid-filled and empty holes. A brief discussion of neutron moderation, diffusion and capture shows that logs using epithermal neutron detection depend on a smaller number of formation-characterizing parameters than those using thermal neutron or capture gamma ray detection. Thus, they come closer to providing an unambiguorls determination of hydrogen content. In this new device a directionally sensitive epithertnal neutron detection system has been incorporated in a side-wall source-detector skid to minimize borehole effects. The effects of variations in borehole size and shape, mud type, temperature and salinity are greatly reduced. Small residual borehole effects are then computationally accounted for in the surface control panel to provide a borehole-corrected neutron log. The log presents a direct recording of neutron-derived porosity on a linear scale. With corrections for borehole effects already applied, this direct recording of porosity simplifies log interpretation. Furthermore, comparison with a linear porosity presentation of a formation density log permits sandstones, limestones and dolomites to be readily identified. Thus, in complex or variable lithology, porosity is determined with greater accuracy and reliability than heretofore. Laboratory data and field results demonstrate the improvements in neutron logging afforded by this new side-wall epithermal neutron logging device. INTRODUCTION The new Sidewall Neutron Porosity (SNP) logging system, designed for use in uncased wells, provides reliability and accuracy never before achieved with neutron logs. The effects of variations in borehole diameter and shape, fluid salinity, mud weight and temperature—parameters that have long complicated neutron log interpretation— are suppressed or corrected for by this sidewall epithermal neutron detection system. Furthermore, to simplify interpretation the SNP log presents a direct recording of computed porosity on a linear scale. The performance improvements achieved by this new system arise primarily from the combination of two im- portant design features. First. though not unique to this new tool, an epithermal neutron detection system is used,',' Epithermal neutron detection substantially reduces the perturbing influences of the thermal neutron absorption properties of rock matrices and water salinity. Second, the neutron detection system is mounted in a directionally sensitive sidewall skid to greatly minimize borehole effects. The purpose of this paper is to explain briefy the advantages offered by the detection of epithermal neutrons, to describe the SNP equipment and the log, to present calibration and correction data and to give examples of interpretation methods made especially convenient by this new system. ADVANTAGES OF EPITHERMAL NEUTRON DETECTION Epithermal neutron detection, of all the neutron methods in current commercial use, provides the simplest determination of formation hydrogen content. Advantages of epithermal neutron detectors, as compared with thermal neutron and gamma ray detectors, are probably best explained by a brief review of the life of a source-emitted neutron. A fast neutron from the source will eventually be cap-tured by the nucleus of an atom. However. before capture is likely to occur, the fast neutron (energy of 100,000 electron volts (ev) or more) will be slowed down until it is in thermal equilibrium with its surroundings. The neutron is then considered to be a "thermal" neutron (average energy of 0.025 ev at 25C). The overwhelming majority of the slowing down thus occurs in reaching epithermal energies (energies just above thermal—0.5 to several ev). After reaching thermal energy. the neutron will "diffuse" through the formation with, on the average, no further energy change until capture. Upon the capture of the thermal neutron, relatively high energy gamma rays arc usually emitted. Hydrogen plays a very important role in the process of slowing down fast neutrons. On the other hand, the absorption effects of water salinity and low concentrations of other strong thermal neutron absorbers—relatively unimportant in the moderation process-—are very important in thermal diffusion, capture and the production of gamma rays. Thus, by detecting only epithermal neutrons with the SNP, spurious effects due to these thermal neutron absorbers are greatly minimized as compared to the effects on tools using thermal neutron or gamma ray detectors. The epithermal neutron detection system affords another important advantage. Log response in various litho-

Jan 1, 1967

By N. R. Adsit

THE B-Ni system was chosen for this study because of the great interest being shown in boron-fiber-strengthened composite materials. Boron fibers were obtained from Texaco Experiment, Inc. They average 4.2 mils in diam with a 0.5-mil tungsten wire in the center. In order to make the diffusion couple, the fibers were included in the nickel matrix by electroforming. The samples were placed in a preheated furnace for the desired temperature and length of time. Sectioning and polishing the samples revealed concentric rings as shown in Fig. 1. The average penetration distance, X, was calculated by measuring the radius of the second phase (the white shell in Fig. 1) and subtracting the original radius. The second phase was identified as NiB by X-ray diffraction. This allows the kinetics of the formation of the phase NiB to be calculated by Eq. [I], which is taken from offman:"

Jan 1, 1967

By R. D. Pehlke, J. V. Gluck

AS a portion of a general study of liquid-metal thermodynamics, high-temperature galvanic cells were used to study the effect of added dilute solutes on the activity of zinc in dilute solution with molten bismuth in the range 450° to 650°C. 1,2 The cells were of the type The experimental procedures have been described previously.1 In the course of studies conducted in the bismuth-rich corner of the systems Bi-Zn-Au and Bi-Zn-Cu, marked discontinuities were observed in the electromotive force-temperature relations for a number of the experimental compositions. Above the discontinuity temperatures, the relations, which were linear, exhibited slopes similar to the binary alloy of the same mole fraction zinc, as shown in Figs. I and 2. Below the discontinuity temperatures, the slopes were markedly different, but the relations remained linear. In general, as the amount of the third eletnent was increased, the slope of the lower portion of the relations tended to become less positive. The slopes of electromotive force-temperature relations reflect the entropy of mixing of zinc and, therefore, the occurrence of a discontinuity marks the transition between two different equilibrium situations involving the solution of zinc. A number of other investigators3-5 have used such observations to determine liquidus boundaries in binary alloys. Since the upper portions of the ternary electromotive force-temperature relations of this study had the same slopes as the binary alloys, the discontinuities are interpreted as marking the transition between the single-phase liquid region and the underlying two- and three-phase regions. Reference to the Zn-Bi equilibrium diagram6 confirms that the binary alloys were single-phase liquids at the experimental temperatures. Fig. I shows the electromotive force-temperature relations for the alloys containing Bi-Zn-Au and Fig. 2 shows similar relations for the Bi-Zn-Cu alloys. In the lower portion of each figure, the temperature of the discontinuity is plotted vs the mole fraction of the added solute at the various levels of zinc concentra- tion. Cross-plots from these curves at constant temperature permitted the construction of the partial liquidus surface isotherms shown in Figs. 3 and 4.

Jan 1, 1967

By Bengt Helmerson

A new tankhouse was started in January 1959 at the Copper Refinery of the Boliden Co., Skelleftehamn, Sweden. In early 1961 a semiautomatic machine for looping and straightening of starting sheets was introduced to substitute previous manual operations. The machine as well as consequent, racking and handling is described. Finally, economic benefits achieved and new constructions for the future are discussed. HISTORY Tankhouse operations at the Boliden Co. 's Smelter in Skelleftehamn started in 1932 on a scale that since then has been gradually increasing. In order to rationalize the operations, a new tankhouse was erected. It went into production in January 1959 and was designed for a yearly production of 35,000 metric tons at a current density of 16 amps per sq ft. Already from the beginning, however, the tankhouse has been run with a current density of 21.5 amps per sq ft, corresponding to a maximum capacity of 50,000 tons a year. During the time of planning of the new tankhouse, due consideration was given to the possibilities of mechanizing the operations. New ideas could be and were actually tested on full or pilot plant scale in the old tankhouse. In that way we developed a system for the cathode handling including washing, weighing, and transportation. A system using forklift trucks in combination with trailers and overhead cranes has been developed for transportation and racking of anodes and also for handling of anode scrap. With respect to the electrolyte, circulation and temperature control are partly automatic. Special attention was paid to the production of starting sheets, which operation normally requires a great number of man hours, and it was made the object of a particular survey as to the best ways of straightening starting sheets, attaching loops to the sheets, and so forth. As a result, a machine was designed during 1957-58 and built in our own shops. After a period of tests, the new equipment was put in operation commercially on the 10th of April, 1961. Since this date the machine has produced about 2 million starting sheets without interruption and has been the only source of looped starting sheets for the tankhouse. GENERAL DESCRIPTION Fig. 1 shows all the major parts of the system. These parts are: slitting machine with feeding table (I), standard roller leveler, type Ungerer (2), tilting roller table (3), conveyors for sheets and suspension bars (4, 7), storage of suspension bars (51, punching and stitching machine (6), two lift-turn-tilt tables (8) for discharging the starting sheets, two rack conveyors (9) for sheet assemblies. Included are a hy-daulic pump station and panels for pneumatic and electric controls. SLITTING AND STRAIGHTENING The machine is fed by hand by a man sitting in front of the slitting-machine table, Fig. 2. This operator inserts one sheet at a time into the slitter. After being trimmed, the sheet is automatically conveyed to the following step of handling, straightening. The slitting machine cuts away about 8 mm of the upper and lower parts of the sheet (in relation to its original position in the stripper section) for two reasons. The first one is to give the machine sheets of uniform dimensions; the second one is a matter of quality. Normally the starting sheets as stripped have a thick edge at the bottom end. This part would collect anode slimes and might also cause short circuits when inserted in the cells without trimming. The straightener used is of German construction

Jan 1, 1967

Jan 1, 1967

By A. L. Service

In 1965 the Western phosphate industry ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock and phosphate rock products. It has become an important regional industry and, since the close of World War II, it has become important in the national phosphate economy. This report includes an evaluation of the trends and outlook for the Western phosphate industry through 1975 as part of the Bureau's program to determine the rate at which the Nation's mineral resources are being utilized. The first part of this report is concerned with the relationship between the Western phosphate industry and that of the United States and the world. It describes the principal phosphate deposits and discusses production, export, and import of phosphate rock and marketable products. The second part of the report is concerned with the Western phosphate industry and discusses trends and outlook through 1975. Projections for the utilization of phosphate rock, phosphate fertilizers, and elemental phosphorus have been developed and extended through 1975 in an effort to provide data and information pertaining to the rate of depletion of the Nation's phosphate resources.

Jan 1, 1967

By David W. James, Howard Jones, George M. Leak

Conditions are described for producing, by primary recrystallization, a matrix suitable for the growth of large grains near (110)[001] orientation in silicon iron strip by secondary recrystallizaliun in a steep temperature gradient. The orientation distribution of these large grains is expressed in terms of rotational deviations about the cross-rolling direction, the rolling direction, and the normal to the sheet, the deviational spread increasing in that order. With the aid of cowplenientary published data on the orientation dependence of growth rate, it is shown that this observation is consistent with the oriented-growth theory of recrystallization lextures. It is conclutled that growth-rate and orientation-distribution data obtained in a steep thermal gradient should be used with caution to account for isothermally Produced recrystallization textures. SEVERAL authors have reported methods of growing large grains by re crystallization of a small-grained matrix in silicon iron 1- B and pure a cr The present study was a preliminary in the growth of single crystals and bicrystals for surface relaxation," grain boundary mobility, and grain boundary diffusion studies. The method was to control the growth of a seed crystal into a suitable primary re crystallized matrix by feeding through a steep temperature gradient. The driving energy for growth derived from the grain boundary energy released as the seed crystals grew into the matrix. Thus, stability of the matrix against normal grain growth was considered to be essential for success. It was known that the manganese sulfide dispersion present in commercial silicon iron performs this function during secondary recrystallization to the (110)[001.] texture.12 Hence commercial, rather than high-purity, material was used throughout. The paper describes the growth conditions for grains large enough to be used as seed crystals for further growth into single crystals. The orientation distribution of the seed crystals is analyzed and its significance for the theory of recrystallization textures is discussed. EXPERIMENTAL PROCEDURE Strip material was supplied by the Steel Co. of Wales, Ltd. The chemical analysis in weight percent was Si, 2.90; C, 0.015; Mn, 0.059; P, 0.011; S, 0.027; Ni, 0.032; 0, 0.009; Fe, balance. A gradient furnace of similar design to one described previously4 was loaned from B.I.S.R.A. It consisted essentially of a vertical water-cooled copper slot projecting downwards into the hot zone of a molybdenum furnace. Hydrogen was passed through the furnace to protect both heating element and specimen from oxidation. Strip specimens up to 8 cm wide and 0.2 cm thick were sealed into the furnace at the mouth of the copper slot. A coating of light oil on the strip surface maintained the seal during translation of a specimen. The maximum temperature gradient in the region just below the copper slot was 500°C per cm over 1 cm, with the hottest point controlled at 1175°C. Several large grains would usually grow by secondary recrystallization from the primary matrix when a specimen was immersed in the hot zone for about 30 min. A back-reflection X-ray camera was constructed to facilitate rapid and accurate orientation determinations of the large grains produced. It was possible to reproduce a standard geometry, with regard to strip and camera, without the tedium of careful alignment on each occasion. Specimens, typically 4 cm wide and 75 cm long, were cut with the longitudinal axis parallel to the rolling direction of the original strip. The surfaces were cleaned by immersion alternately in a hot aqueous solution containing 2 pct hydrofluoric acid plus 10 pct sulfuric acid and in cold 10 pct nitric acid. The nitric acid etch was just sufficient to reveal the grain structure. Rolling and annealing treatments to prepare the matrix (discussed below) were followed by growth of seed crystals in the gradient furnace. The matrix was transformed to a single crystal by growth of a selected seed crystal connected to the matrix by a thin neck. 4,5 Growth was promoted by controlled feeding into the gradient furnace. Several single crystals of controlled orientation were grown successfully from seed crystals by twisting the interconnecting neck in a reorien-tation jig.4 EXPERIMENTAL RESULTS AND DISCUSSION Growth Conditions. A suitable matrix for growth of large grains was prepared starting from primary re-crystallized strip 1.9 mm thick. This was cold-rolled in two stages each being followed by a recrystallization anneal at 800°C for a few minutes. Such treatment gave the required growth matrix only if the two cold-reduction stages were each performed in several passes and in the following ranges: the first, 30 to 70 pct; the second, 10 to 50 pct. Immersion in the temperature gradient otherwise resulted in an equiaxed

Jan 1, 1967

By R. E. Hamilton

"The requirements for effective optimization of a mineral dressing operation are discussed, with specific reference to a flotation system . Also considered are the relation-ships between automatic control and optimization pro-grams. Variables are classified into the following groups, and the significance of the classification is discussed: (a) Directly measurable (b) Directly manipulable (c) Uncontrollable (d) Calculable from measurable variables (e) Affected by changes in manipulable or uncontrol-lable variables. New sensors for measuring variables not normally measured are described."

Jan 1, 1967

By J. B. Zink

The Bureau of Mines developed a spectrochemical method to determine six constituents in coal ash in the following concentration ranges: silica 9 to 63 percent, alumina 7.5 to 35 percent, ferric oxide 2 to 30 percent, calcium oxide 1 to 29 percent, magnesium oxide 0.5 to 6 percent, and titanium oxide 0.5 to 4 percent. Samples of coal ash are fused with a mixture of lithium tetraborate and vanadium pentoxide. The resulting beads are crushed, mixed with powdered graphite, and briquetted. The pellets are analyzed spectrographically, using controlled high-voltage spark excitation. Vanadium serves as the internal standard. Effects due to matrix variations are minimized by fusion with lithium tetraborate. Intensity ratios of selected analytical lines are determined photometrically, Concentrations are read from analytical curves, prepared from synthetic standards, relating log intensity ratios to log concentration. A combustion procedure is used to determine sulfur tri-oxide. The method is most useful when large numbers of coal ashes must be analyzed but a high degree of accuracy is not essential.

Jan 1, 1967